This patch adds support for the watchdog core found on newer MediaTek Wifi
SoCs MT7621 and MT7628. There is no symbol for MT7628 as it is a subtype of
MT7620 so we depend on that instead.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds support for the Sigma Designs SMP86xx/SMP87xx family built-in
watchdog.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Zodiac Aerospace RAVE Watchdog Procesor.
This device implements a watchdog timer, accessible over I2C.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add WD support for Alphascale asm9260 SoC. This driver
provide support for different function modes:
- HW mode to trigger SoC reset on timeout
- SW mode do soft reset if needed
- DEBUG mode
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog is instantiated in a FPGA that is memory mapped. It is
made of only one register, called the feed register. Writing to this
register will re-arm the watchdog for a given time (and enable it if it
was disable). It can be disabled by writing a special value into it.
It is part of a syscon block, and the watchdog register offset in this
block varies from board to board. This offset is passed in the syscon
property after the phandle to the syscon node.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds watchdog driver for CSRatlas7 platform.
On CSRatlas7, the 6th timer can act as a watchdog timer
when the Watchdog mode is enabled.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: William Wang <William.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
From SAMA5D4, the watchdog timer is upgrated with a new feature,
which is describled as in the datasheet, "WDT_MR can be written
until a LOCKMR command is issued in WDT_CR".
That is to say, as long as the bootstrap and u-boot don't issue
a LOCKMR command, WDT_MR can be written more than once in the driver.
So the SAMA5D4 watchdog driver's implementation is different from
the at91sam9260 watchdog driver implemented in file at91sam9_wdt.c.
The user application open the device file to enable the watchdog timer
hardware, and close to disable it, and set the watchdog timer timeout
by seting WDV and WDD fields of WDT_MR register, and ping the watchdog
by issuing WDRSTT command to WDT_CR register with hard-coded key.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the watchdog timer found in NXP LPC SoCs
family, which includes LPC18xx/LPC43xx. Other SoCs in that family may
share the same watchdog hardware.
Watchdog driver registers a restart handler that will restart the system
by performing an incorrect feed after ensuring the watchdog is enabled in
reset mode.
As watchdog cannot be disabled in hardware, driver's stop routine will
regularly send a keepalive ping using a timer.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add watchdog driver support for DA9062
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit add a driver for the watchdog functionality of the Conexant CX92755
SoC, from the Digicolor series of SoCs. Of 8 system timers provided by the
CX92755, the first one, timer A, can reset the chip when its counter reaches
zero. This driver uses this capability to provide userspace with a standard
watchdog, using the watchdog timer driver core framework. This driver also
implements a reboot handler for the reboot(2) system call.
The watchdog driver shares the timer registers with the CX92755 timer driver
(drivers/clocksource/timer-digicolor.c). The timer driver, however, uses only
timers other than A, so both drivers should coexist.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Mediatek SoC integrated
watchdog. This driver supports watchdog and software reset
for mt65xx and mt81xx SoCs.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the watchdog driver for the Amlogic Meson SoCs used also
to reboot the device.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver supports the watchdog device inside the DA9063 PMIC.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for the watchdog timer available in Ricoh RN5T618
PMIC. The device supports a programmable expiration time of 1, 8, 32
or 128 seconds.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the watchdog timer block found in the Krait Processor
Subsystem (KPSS) on the MSM8960, APQ8064, and IPQ8064.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add Cadence WDT driver. This is used by Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added driver to support the 14F021P00 BMC Watchdog.
The BMC is a Board Management Controller including watchdog functionality.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
Add initial Intel MID watchdog driver support.
This driver is an initial implementation of generic Intel MID watchdog
driver. Currently it supports Intel Merrifield platform.
Signed-off-by: Eric Ernst <eric.ernst@intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since both chips are now supported by the w83627hf watchdog driver,
the chip specific drivers are no longer needed and can be removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Converted the vmwatchdog driver to use the kernel's watchdog API.
Signed-off-by: Philipp Hachtmann <phacht@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a driver for the hardware watchdogs in NVIDIA Tegra SoCs (Tegra30 and
later). This driver will configure one watchdog timer that will reset the
system in the case of a watchdog timeout.
This driver binds to the nvidia,tegra30-timer device node and gets its
register base from there.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a watchdog driver for devices controlled through GPIO,
(Analog Devices ADM706, Maxim MAX823, National NE555 etc).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the watchdog timer used on the BCM281xx
family of SoCs.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On CSR SiRFprimaII and SiRFatlasVI, the 6th timer can act as a watchdog
timer when the Watchdog mode is enabled.
watchdog occur when TIMER watchdog counter matches the value software
pre-set, when this event occurs, the effect is the same as the system
software reset.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a watchdog driver for the main hardware watchdog timer
found on MOXA ART SoCs.
The MOXA ART SoC provides one writable timer register, restarting
the hardware once it reaches zero. The register is auto decremented
every APB clock cycle.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the driver for the watchdog found in the Allwinner A10 and
A13 SoCs. It has DT-support and uses the new watchdog framework.
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the driver for the watchdog devices found on MEN Mikro
Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the
watchdog framework.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for watchdog timer hardware present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add watchdog timer support for the on-board PLD found on some Kontron
embedded modules.
Originally-From: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that the new driver is in place, we can remove the old one.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Replace the existing STMP3xxx driver because it has enough drawbacks
that a rewrite is apropriate. The new driver is designed to use the
watchdog framework which makes it a lot smaller and avoids open coding
the watchdog API again. It also uses now an explicitly exported function
from the RTC driver to set up its registers (the old driver silently
reused the hopefully(!) already remapped RTC registers). Also, this
driver is mach independent, while the old one depends on a mach replaced
by another one a year ago. Since the user interface is still the
standard watchdog API, users don't need to adapt.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the ux500_wdt watchdog that is found in
ST-Ericsson Ux500 platform. The driver is based on PRCMU APIs.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the Watchdog patch for the DA9055 PMIC. This patch has got dependency on
the DA9055 MFD core.
This patch is functionally tested on SMDK6410
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver adds support for the watchdog functionality provided by
the Dialog Semiconductor DA9052 PMIC chip.
Tested on samsung smdkv6410 and i.mx53 QS boards.
Signed-off-by: Anthony Olech <Anthony.Olech@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add driver for the watchdog timer built into the
Intel Atom E6XX (TunnelCreek) processor.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The platform is removed, so there are no users of this driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
New driver for the hardware watchdog timer on VIA chipsets.
This driver uses the new watchdog framework.
PnP must be enabled in BIOS to get full control of watchdog registers.
The timer code has been added by Wim Van Sebroeck.
Tested on a Artigo A1100, VX855 chipset.
Signed-off-by: Marc Vertes <marc.vertes@sigfox.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove the driver (that was added in v2.6.32) since the architecture
has never been merged into mainline.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WatchDog Timer Driver Core is a framework
that contains the common code for all watchdog-driver's.
It also introduces a watchdog device structure and the
operations that go with it.
This is the introduction of this framework. This part
supports the minimal watchdog userspace API (or with
other words: the functionality to use /dev/watchdog's
open, release and write functionality as defined in
the simplest watchdog API). Extra functionality will
follow in the next set of patches.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Watchdog timer device driver for Xilinx xps_timebase_wdt compatible ip cores.
It takes watchdog timer configuration from device tree and it needs that its
parent has defined the property "clock-frecuency".
It is compatible with watchdog timer kernel API, so user apps like watchdogd
may talk with it.
Signed-off-by: Alejandro Cabrera <aldaya@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Synopsys DesignWare watchdog is found in several ARM based systems
and provides a choice of 16 timeout periods depending on the clock
input. The watchdog cannot be disabled once started.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
John Crispin