MDIO busses typically operate at 2.5MHz. However many devices can
operate at faster speeds. This then allows more MDIO transactions per
second, useful for Ethernet switch statistics, or Ethernet PHY TDR
data. Allow the bus speed to be configured, using the standard
"clock-frequency" property, which i2c busses use to indicate the bus
speed. Before using this property, ensure all devices on the bus do
actually support the requested clock speed.
Suggested-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Measurements of the MDIO bus have shown that driving the MDIO bus
using interrupts is slow. Back to back MDIO transactions take about
90us, with 25us spent performing the transaction, and the remainder of
the time the bus is idle.
Replacing the completion interrupt with polled IO results in back to
back transactions of 40us. The polling loop waiting for the hardware
to complete the transaction takes around 28us. Which suggests
interrupt handling has an overhead of 50us, and polled IO nearly
halves this overhead, and doubles the MDIO performance.
Suggested-by: Chris Heally <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline rtl8169_make_unusable_by_asic() and simplify it:
- Address field doesn't need to be poisoned because descriptor is
owned by CPU now
- desc->opts1 is set by rtl8169_mark_to_asic() and rtl8169_rx_fill(),
therefore we don't have to preserve any field parts.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_mark_as_last_descriptor() has just one user, so inline it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2020-04-19
This series contains updates to e1000e and igc only.
Sasha adds new device IDs supported by the igc driver.
Vitaly fixes the S0ix entry and exit flows in e1000e for TGP and newer
MAC types when a cable is connected.
Andre has the remaining changes in the series, starting with cleanup of
the igc driver of duplicate code. Added a check for
IGC_MAC_STATE_SRC_ADDR flag which is unsupported for MAC filters in igc.
Cleaned up the return values for igc_add_mac_filter(), where the return
value was not being used, so update the function to only return success
or failure. Fix the return value of igc_uc_unsync() as well. Refactor
the igc driver in several functions to help reduce the convoluted logic
and simplify the driver filtering mechanisms. Improve the MAC address
checks when adding a MAC filter. Lastly, improve the log messages
related to MAC address filtering to ease debugging.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove casting the values returned by memory allocation function.
Coccinelle emits WARNING: casting value returned by memory allocation
function to struct pointer is useless.
This issue was detected by using the Coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove casting the values returned by memory allocation function.
Coccinelle emits WARNING: casting value returned by memory allocation
function to (struct cas_init_block *) is useless.
This issue was detected by using the Coccinelle software.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Infrastructure Entry Delete Register (IEDR) is used to delete
entries stored in the KVD linear database. Currently, it is only
possible to delete entries of size up to 2048. Future firmware versions
will support deletion of entries of size up to 4096.
Increase the size of the field so that the driver will be able to
perform such deletions in the future, when required.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit fc25996e6f ("mlxsw: spectrum_router: Increase
scale of IPv6 nexthop groups"), each nexthop group is hashed by XOR-ing
the interface indexes of all the member nexthop devices.
To avoid many different nexthop groups ending up using the same key, the
above commit started hashing the interface indexes themselves before
they are XOR-ed.
However, in cases in which there are many nexthop groups that all use
the same nexthop device and only differ in the gateway IP, we can still
end up in a situation in which all the groups are using the same key.
This eventually leads to -EBUSY error from rhashtable during insertion.
Improve the situation by also making the gateway IP part of the key.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Realtek PHY driver takes care of adding the needed delay now,
therefore we can remove the delay here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:700:2-8: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:702:2-8: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds log messages to functions related to the MAC address
filtering code to ease debugging.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does a code refactoring in igc_del_mac_filter() so it uses
the new helper igc_find_mac_filter() and improves the comment about the
special handling when deleting the default filter.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The helper igc_mac_entry_can_be_used() implementation is a bit
convoluted since it does two different things: find a not-in-use slot
in mac_table or find an in-use slot where the address and address type
match. This patch does a code refactoring and break it up into two
helper functions.
With this patch we might traverse mac_table twice in some situations,
but this is not harmful performance-wise (mac_table has only 16 entries
and adding mac filters is not hot-path), and it improves igc_add_mac_
filter() readability considerably.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the previous two patches, igc_add_mac_steering_filter() and
igc_del_mac_steering_filter() became a pointless wrapper of
igc_add_mac_filter() and igc_del_mac_filter().
This patch removes these wrappers and update callers to call
igc_add_mac_filter() and igc_del_mac_filter() directly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The IGC_MAC_STATE_QUEUE_STEERING bit in mac_table[i].state is
utilized to indicate that frames matching the filter are assigned to
mac_table[i].queue. This bit is not strictly necessary since we can
convey the same information as follows: queue == -1 means queue
assignment is disabled, otherwise it is enabled.
In addition to make the code simpler, this change fixes some awkward
situations where we pass a complete misleading 'queue' value such as in
igc_uc_sync().
So this patch removes IGC_MAC_STATE_QUEUE_STEERING and also takes the
opportunity to improve the igc_add_mac_filter documentation.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igc_add_mac_filter() doesn't allow us to have more than one entry with
the same address and address type in adapter->mac_table so checking if
'queue' matches in igc_del_mac_filter() isn't necessary. This patch
removes that check.
This patch also takes the opportunity to improve the igc_del_mac_filter
documentation and remove comment which is not applicable to this I225
controller.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igc_add_mac_filter() doesn't allow filters with invalid MAC address to
be added to adapter->mac_table so, in igc_del_mac_filter(), we can early
return if MAC address is invalid. No need to traverse the table.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current igc_rar_set_index() implementation is a bit convoluted so this
patch does some code refactoring to improve it.
The helper igc_rar_set_index() is about writing MAC filter settings into
hardware registers. Logic such as address validation belongs to
functions upper in the call chain such as igc_set_mac() and
igc_add_mac_filter(). So this patch moves the is_valid_ether_addr() call
to igc_add_mac_filter(). No need to touch igc_set_mac() since it already
checks it.
The variables 'rar_low' and 'rar_high' represent the value in registers
RAL and RAH so we rename them to 'ral' and 'rah', respectively, to
match the registers names.
To make it explicit, filter settings are passed as arguments to the
function instead of reading them from adapter->mac_table "under the
hood". Also, the function was renamed to igc_set_mac_filter_hw to make
it more clear what it does.
Finally, the patch removes some wrfl() calls and comments not needed.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case igc_del_mac_filter() returns error, that error is masked
since the functions always return 0 (success). This patch fixes
igc_uc_unsync() so it returns whatever value igc_del_mac_filter()
returns (0 on success, negative number on error).
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of success, igc_add_mac_filter() returns the index in
adapter->mac_table where the requested filter was added. This
information, however, is not used by any caller of that function.
In fact, callers have extra code just to handle this returning
index as 0 (success).
So this patch changes the function to return 0 on success instead,
and cleans up the extra code.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The IGC_MAC_STATE_SRC_ADDR flags is not supported by igc_add_mac_
filter() so this patch adds a check for it and returns -ENOTSUPP
in case it is set.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does a code refactoring in the MAC address filtering logic to
get rid of some duplicate code.
IGC driver has two functions to add MAC address filters that are pretty
much the same: igc_add_mac_filter() and igc_add_mac_filter_flags(). The
only difference is that the latter allows the callee to specify the
'flags' parameter while the former has it hard coded as zero. The same
rationale applies to filter deletion counterparts.
So this patch refactors igc_add_mac_filter() and igc_del_mac_filter() so
they handle the 'flags' parameters, removes the _flags() functions, and
fixes callees accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added a fix to S0ix entry and exit flows for TGP and above
MAC types, to the case when the Ethernet cable is connected
and the link is up. With that the system is able to reach
SLP_S0 when going to freeze power state.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device IDs for the next step of i225
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add workaround for hw issues with TSO on RTL8168evl. This workaround is
based on information I got from Realtek, and *should* allow to safely
enable TSO on this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and avoid the overhead of calling vlan_get_protocol().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At that place in rtl_init_one() we can safely use rtl8169_set_features()
to configure the chip according to the default features.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we set RX_VLAN_8125 unconditionally, even if
NETIF_F_HW_VLAN_CTAG_RX may not be set. Don't touch these bits,
and let only rtl8169_set_features() control them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HIGHDMA is added to vlan_features by register_netdev(),
therefore we can omit this here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting the ocp_base to rtl_init_one(). Where supported the value
is always the same, and if not supported it doesn't hurt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each ENETC station interface (SI) has a VLAN filter list and a port
flag (PSIPVMR) by which it can be put in "VLAN promiscuous" mode, which
enables the reception of VLAN-tagged traffic even if it is not in the
VLAN filtering list.
Currently the handling of this setting works like this: the port starts
off as VLAN promiscuous, then it switches to enabling VLAN filtering as
soon as the first VLAN is installed in its filter via
.ndo_vlan_rx_add_vid. In practice that does not work out very well,
because more often than not, the first VLAN to be installed is out of
the control of the user: the 8021q module, if loaded, adds its rule for
802.1p (VID 0) traffic upon bringing the interface up.
What the user is currently seeing in ethtool is this:
ethtool -k eno2
rx-vlan-filter: on [fixed]
which doesn't match the intention of the code, but the practical reality
of having the 8021q module install its VID which has the side-effect of
turning on VLAN filtering in this driver. All in all, a slightly
confusing experience.
So instead of letting this driver switch the VLAN filtering state by
itself, just wire it up with the rx-vlan-filter feature from ethtool,
and let it be user-configurable just through that knob, except for one
case, see below.
In promiscuous mode, it is more intuitive that all traffic is received,
including VLAN tagged traffic. It appears that it is necessary to set
the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
also temporarily enabled. On exit from promiscuous mode, the setting
made by ethtool is restored.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the VCAP IS2 will produce a single match for each frame, on
the most specific classification.
Example: a ping packet (ICMP over IPv4 over Ethernet) sent from an IP
address of 10.0.0.1 and a MAC address of 96:18:82:00:04:01 will match
this rule:
tc filter add dev swp0 ingress protocol ipv4 \
flower skip_sw src_ip 10.0.0.1 action drop
but not this one:
tc filter add dev swp0 ingress \
flower skip_sw src_mac 96:18:82:00:04:01 action drop
Currently the driver does not really warn the user in any way about
this, and the behavior is rather strange anyway.
The current patch is a workaround to force matches on MAC_ETYPE keys
(DMAC and SMAC) for all packets irrespective of higher layer protocol.
The setting is made at the port level.
Of course this breaks all other non-src_mac and non-dst_mac matches, so
rule exclusivity checks have been added to the driver, in order to never
have rules of both types on any ingress port.
The bits that discard higher-level protocol information are set only
once a MAC_ETYPE rule is added to a filter block, and only for the ports
that are bound to that filter block. Then all further non-MAC_ETYPE
rules added to that filter block should be denied by the ports bound to
it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug when the user adds the first MAC address filter
via ethtool NFC mechanism.
When the first MAC address filter is added, it overwrites the default
MAC address filter configured at RAL[0] and RAH[0]. As consequence,
frames addressed to the interface MAC address are not sent to host
anymore.
This patch fixes the bug by calling igc_set_default_mac_filter() during
adapter init so the position 0 of adapter->mac_table[] is assigned to
the default MAC address.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IGC driver has no support for tc-flower filters so this patch removes
some leftover code, probably copied from IGB driver by mistake.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The support for ethtool Network Flow Classification (NFC) queue
redirection based on destination MAC address is currently broken in IGC.
For instance, if we add the following rule, matching frames aren't
enqueued on the expected rx queue.
$ ethtool -N IFNAME flow-type ether dst 3c:fd:fe:9e:7f:71 queue 2
The issue here is due to the fact that igc_rar_set_index() is missing
code to enable the queue selection feature from Receive Address High
(RAH) register. This patch adds the missing code and fixes the issue.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i225 device support copper mode only
PHY signal detect indication for copper fiber switch
not applicable to i225 part
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This assignment of the feature NETIF_F_HW_TC
occurs prior to the initial setup of the local
hw_features variable.
This ensures that NETIF_F_HW_TC are marked
as user changeable, and also enables it by
default when the driver loads.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IGC_START_ITR has beed defined twice
This patch come to fix it
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes some register overwriting when dumping registers via
ethtool.
We have a total of 16 RAL registers, starting at offset 139. So RAH
offset should be 139 + 16 = 155, not 145. As result some RAL registers
are overwritten. Likewise, RAH registers are also overwritten by TDBAL,
TDBAH, TDLEN, and TDH registers.
To fix this bug while preserving the ABI, this patch re-writes RAL and
RAH registers at the end of 'regs_buff' and bumps regs->version. It also
removes some pointless comments in the middle of igc_set_regs().
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move igc_adapter and igc_ring structures up to avoid
forward declaration
It is not necessary to forward declare these structures
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We support only copper mode
Not applicable for i225 parts
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Formally Destination bit should be kept reserved to
support legacy drivers and ignore on write/read
operation
Not applicable for i225 parts
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.
To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.
drivers/net/ethernet/intel/e1000/e1000_main.c: In function ‘e1000_xmit_frame’:
drivers/net/ethernet/intel/e1000/e1000_main.c:3143:18: warning: statement will never be executed [-Wswitch-unreachable]
3143 | unsigned int pull_size;
| ^~~~~~~~~
[1] https://bugs.llvm.org/show_bug.cgi?id=44916
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds support for ETF offloading for the i225 controller.
For i225, the LaunchTime feature is almost a subset of the Qbv
feature. The main change from the i210 is that the launchtime of each
packet is specified as an offset applied to the BASET register. BASET
is automatically incremented each cycle.
For i225, the approach chosen is to re-use most of the setup used for
taprio offloading. With a few changes:
- The more or less obvious one is that when ETF is enabled, we should
set add the expected launchtime to the (advanced) transmit
descriptor;
- The less obvious, is that when taprio offloading is not enabled, we
add a dummy schedule (all queues are open all the time, with a cycle
time of 1 second).
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support for translating taprio schedules into i225 cycles. This
will allow schedules to run in the hardware, making the schedules
enforcement more precise and saving CPU time.
Right now, the only simple schedules are allowed, complex schedules are
rejected. "simple" in this context are schedules that each HW queue is
opened and closed only once in each cycle.
Changing schedules is still not supported as well.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Partial generic segmentation offload is a hybrid between TSO and GSO.
What is effectively does is take advantage of certain traits of TCP and
tunnels so that instead of having to rewrite the packet headers for each
segment only in the inner-most transport header and possible the outer-most
network header need to be updated.
This allows devices that do not support tunnel offload or tunnels
offloads with checksum to still make use of segmentation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver uses __napi_schedule_irqoff() which is fine as long as it is
invoked with disabled interrupts by everybody. Since the commit
mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq
context. This may lead to list corruption if another driver uses
__napi_schedule_irqoff() in IRQ context.
Use __napi_schedule() which safe to use from IRQ and softirq context.
Fixes: 85b85c8534 ("amd-xgbe: Re-issue interrupt if interrupt status not cleared")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit bfcb813203 ("net: dsa:
configure the MTU for switch ports") my Lamobo R1 platform which uses
an allwinner,sun7i-a20-gmac compatible Ethernet MAC started to fail
by rejecting a MTU of 1536. The reason for that is that the DMA
capabilities are not readable on this version of the IP, and there
is also no 'tx-fifo-depth' property being provided in Device Tree. The
property is documented as optional, and is not provided.
Chen-Yu indicated that the FIFO sizes are 4KB for TX and 16KB for RX, so
provide these values through platform data as an immediate fix until
various Device Tree sources get updated accordingly.
Fixes: eaf4fac478 ("net: stmmac: Do not accept invalid MTU values")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn