Declare ADC1 clkctrl which feeds the magnetic-reader/ADC1 hardware
module.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-2-miquel.raynal@bootlin.com
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Yu Jiahua <yujiahua1@huawei.com>
Link: https://lore.kernel.org/r/20210616034826.37276-1-yujiahua1@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the omap2_dpll_round_rate routine attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The gpmc clock is needed to update omap5 to boot with genpd with the
related devicetree patches. The ocmc clock is currently not used but
let's add it so we have all the clocks for the l3main2 defined.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/gate.c:67: warning: Function parameter or member 'hw' not described in 'omap36xx_gate_clk_enable_with_hsdiv_restore'
drivers/clk/ti/gate.c:67: warning: Excess function parameter 'clk' description in 'omap36xx_gate_clk_enable_with_hsdiv_restore'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-17-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll.c:163: warning: Function parameter or member 'user' not described in '_register_dpll'
drivers/clk/ti/dpll.c:163: warning: Excess function parameter 'hw' description in '_register_dpll'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-16-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/clockdomain.c:107: warning: Function parameter or member 'hw' not described in 'omap2_init_clk_clkdm'
drivers/clk/ti/clockdomain.c:107: warning: Excess function parameter 'clk' description in 'omap2_init_clk_clkdm'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-14-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll44xx.c:114: warning: Function parameter or member 'hw' not described in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:114: warning: Function parameter or member 'parent_rate' not described in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:114: warning: Excess function parameter 'clk' description in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:150: warning: Function parameter or member 'hw' not described in 'omap4_dpll_regm4xen_round_rate'
drivers/clk/ti/dpll44xx.c:150: warning: Function parameter or member 'parent_rate' not described in 'omap4_dpll_regm4xen_round_rate'
drivers/clk/ti/dpll44xx.c:150: warning: Excess function parameter 'clk' description in 'omap4_dpll_regm4xen_round_rate'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-11-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll3xxx.c:414: warning: Function parameter or member 'hw' not described in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:414: warning: Function parameter or member 'parent_rate' not described in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:414: warning: Excess function parameter 'clk' description in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:437: warning: Function parameter or member 'hw' not described in 'omap3_noncore_dpll_enable'
drivers/clk/ti/dpll3xxx.c:437: warning: Excess function parameter 'clk' description in 'omap3_noncore_dpll_enable'
drivers/clk/ti/dpll3xxx.c:479: warning: Function parameter or member 'hw' not described in 'omap3_noncore_dpll_disable'
drivers/clk/ti/dpll3xxx.c:479: warning: Excess function parameter 'clk' description in 'omap3_noncore_dpll_disable'
drivers/clk/ti/dpll3xxx.c:755: warning: Function parameter or member 'hw' not described in 'omap3_clkoutx2_recalc'
drivers/clk/ti/dpll3xxx.c:755: warning: Function parameter or member 'parent_rate' not described in 'omap3_clkoutx2_recalc'
drivers/clk/ti/dpll3xxx.c:755: warning: Excess function parameter 'clk' description in 'omap3_clkoutx2_recalc'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-4-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/clkt_dpll.c:284: warning: Function parameter or member 'hw' not described in 'omap2_dpll_round_rate'
drivers/clk/ti/clkt_dpll.c:284: warning: Function parameter or member 'parent_rate' not described in 'omap2_dpll_round_rate'
drivers/clk/ti/clkt_dpll.c:284: warning: Excess function parameter 'clk' description in 'omap2_dpll_round_rate'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-3-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ability to get struct clk pointers from a struct clk_hw so that clk providers
can consume the clks they provide, if they need to do something like that. This
has been a long missing part of the clk provider API that will help us move
away from exposing a struct clk pointer in the struct clk_hw. Tracepoints are
added for the clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to help
developers understand the hardware enable state of clks in case firmware or
bootloader state is different than what is expected. Overall the core changes
are mostly improving the clk driver writing experience.
At the driver level, we have the usual collection of driver updates and new
drivers for new SoCs. This time around the Qualcomm folks introduced a good
handful of clk drivers for various parts of three or four SoCs. The SiFive
folks added a new clk driver for their FU740 SoCs, coming in second on the
diffstat and then Atmel AT91 and Amlogic SoCs had lots of work done after that
for various new features. One last thing to note in the driver area is that the
i.MX driver has gained a new binding to support SCU clks after being on the
list for many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and tweaks that
come from more testing and finding out that some configuration was wrong or
that a driver could support being built as a module.
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks
-----BEGIN PGP SIGNATURE-----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=Wt9O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
Having the ABE DPLL ref and bypass muxes set to different inputs was
causing the DPLL not to lock when TIMER8 was used, as it is in the Pyra
for the backlight.
This patch fixes this by setting abe_dpll_bypass_clk_mux to sys_32k_ck
in omap5xxx_dt_clk_init.
A similar patch may also be needed for OMAP44xx which has similar code
in omap4xxx_dt_clk_init, but I have not added this as I have no hardware
to test on.
Signed-off-by: David Shah <dave@ds0.me>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/1d3abe2512054866cc2ea7b2592238f4fa06502a.1607253531.git.hns@goldelico.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If clk_register fails, we should goto free branch
before function returns to prevent memleak.
Fixes: 163152cbbe ("clk: ti: Add support for FAPLL on dm816x")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201113131623.2098222-1-zhangqilong3@huawei.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Similar to what we've done for IPU and DSP let's ignore the status bit
for the IVA clkctrl register.
The clkctrl status won't change unless the related rstctrl is deasserted,
and the rstctrl status won't change unless the clkctrl is enabled.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to what we've done for IPU and DSP let's ignore the status bit
for the IVA clkctrl register.
The clkctrl status won't change unless the related rstctrl is deasserted,
and the rstctrl status won't change unless the clkctrl is enabled.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend and resume to work with genpd on am4, we must keep
l3 main clock always on. Otherwise prm_omap driver will shut down the l3
main clock on suspend when simple-pm-bus and GENPD_FLAG_PM_CLK are used.
Note that we already keep the l3 main clock always on with the legacy
platform code.
Later on we may want to start managing the l3 main clock with a dedicated
interconnect driver instead of using simple-pm-bus and GENPD_FLAG_PM_CLK.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend and resume to work with genpd on am3, we must keep
l3 main clock always on. Otherwise prm_omap driver will shut down the l3
main clock on suspend when simple-pm-bus and GENPD_FLAG_PM_CLK are used.
Note that we already keep the l3 main clock always on with the legacy
platform code.
Later on we may want to start managing the l3 main clock with a dedicated
interconnect driver instead of using simple-pm-bus and GENPD_FLAG_PM_CLK.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a memory leak induced by not calling clk_put after doing of_clk_get.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907082600.454-3-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk pointer passed to omap2_clk_(deny|allow)_idle can be NULL, so
add checks for this.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907082600.454-2-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
Fix the following gcc warning:
drivers/clk/ti/clk-7xx.c:320:43: warning: ‘dra7_gpu_sys_clk_data’
defined but not used [-Wunused-const-variable=]
static const struct omap_clkctrl_div_data dra7_gpu_sys_clk_data
__initconst = {
^~~~~~~~~~~~~~~~~~~~~
drivers/clk/ti/clk-7xx.c:315:27: warning: ‘dra7_gpu_sys_clk_parents’
defined but not used [-Wunused-const-variable=]
static const char * const dra7_gpu_sys_clk_parents[] __initconst = {
^~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lkml.kernel.org/r/20200417073523.42520-1-yanaijie@huawei.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We need sysclk6_ck enabled early as it is needed by l4_ls and system
timers early on boot. This removes the dependency of system timers to
the interconnect related code that can be then probed later on when
suitable at module_init time.
Cc: linux-clk@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This clock entry does not exist on any other devices except DRA76,
so mark it as specific to that SoC only.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200430083640.8621-3-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
gpu_cm:* parent clock name is wrong, replace this with correct
gpu-clkctrl:* clock. Otherwise the clock ends up in the orphaned list.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200430083640.8621-2-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
L4 secure clocks do not have their parents set currently, which ends
them up to the orphan clock list. Fix this by adding either l3 or l4
clock as their parent.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200429131341.4697-4-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
L4 secure clocks do not have their parents set currently, which ends
them up to the orphan clock list. Fix this by adding either l3 or l4
clock as their parent.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200429131341.4697-3-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The parent_names is never released for a component clock definition,
causing some memory leak. Fix by releasing it once it is no longer
needed.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200429131341.4697-2-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Addition of the new internal API to get the clkctrl names missed adding
the same conversion in place for the subclocks. This leads into missed
parent/child relationships (i.e. orphaned clocks) with mixed node name
handling, for example with omap4/omap5 where the l4_per clocks are using
new naming, but rest are using old. Fix by converting the subclock
registration to pick correct names for the clocks also.
Fixes: 6c30905205 ("clk: ti: clkctrl: Fix hidden dependency to node name")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200430083451.8562-1-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Right now, trying to use RTC purely with the ti-sysc / clkctrl framework
fails to enable the RTC module properly. Based on experimentation, this
appears to be because RTC is sourced from the clkdiv32k optional clock.
TRM is not very clear on this topic, but fix the RTC to use the proper
source clock nevertheless.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200424152301.4018-1-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clkctrl_get_name incorrectly calls of_node_put when it is not really
doing of_node_get. This causes a boot time warning later on:
[ 0.000000] OF: ERROR: Bad of_node_put() on /ocp/interconnect@4a000000/segmen
t@0/target-module@5000/cm_core_aon@0/ipu-cm@500/ipu1-clkctrl@20
Fix by dropping the of_node_put from the function.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 6c30905205 ("clk: ti: clkctrl: Fix hidden dependency to node name")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200424124725.9895-1-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
We are missing alwon ethernet clock for dm814x and this prevents us
from probing the CPSW with device tree only data. Looks like Ethernet
currently only works if it has been enabled in the bootloader.
Looks like relying on the bootloader clocks is not an issue with the
mainline kernel currently, but it will be an issue when configuring
CPSW Ethernet to probe with device tree data only as we will be managing
the clocks.
Fixes: 26ca2e9738 ("clk: ti: dm814: add clkctrl clock data")
Cc: linux-clk@vger.kernel.org
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently enabling clkctrl clock on am4 can fail for RTC as the clock
parent is wrong for RTC.
Fixes: 76a1049b84 ("clk: ti: am43xx: add new clkctrl data for am43xx")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20200221171030.39326-1-tony@atomide.com
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is some material that we picked up into our tree late, or that had
more complex dependencies on more than one topic branch that makes sense
to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to better
reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards
-----BEGIN PGP SIGNATURE-----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=R7GU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
the normal collection of driver updates to support new SoCs, fix incorrect
data, and convert various drivers to clk_hw based APIs.
In the core, we allow clk_ops::init() to return an error code now so that we
can fail clk registration if the callback does something like fail to allocate
memory. We also add a new "terminate" clk_op so that things done in
clk_ops::init() can be undone, e.g. free memory. We also spit out a warning now
when critical clks fail to enable and we support changing clk rates and
enable/disable state through debugfs when developers compile the kernel
themselves.
On the driver front, we get support for what seems like a lot of Qualcomm and
NXP SoCs given that those vendors dominate the diffstat. There are a couple new
drivers for Xilinx and Amlogic SoCs too. The updates are all small things like
fixing the way glitch free muxes switch parents, avoiding div-by-zero problems,
or fixing data like parent names. See the updates section below for more
details.
Finally, the "basic" clk types have been converted to support specifying
parents with clk_hw pointers. This work includes an overhaul of the fixed-rate
clk type to be more modern by using clk_hw APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting
-----BEGIN PGP SIGNATURE-----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=UjXu
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
The secure clocks on omap5 are similar to what we already have for dra7
with dra7_l4sec_clkctrl_regs and documented in the omap5432 TRM in
"Table 3-1044. CORE_CM_CORE Registers Mapping Summary".
The secure clocks are part of the l4per clock manager. As the l4per
clock manager has now two clock domains as children, let's also update
the l4per clockdomain node name to follow the "clock" node naming with
a domain specific compatible property.
Compared to omap4, omap5 has more clocks working in hardare autogating
mode.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The secure clocks on omap4 are similar to what we already have for dra7
in dra7_l4sec_clkctrl_regs and documented in the omap4460 TRM "Table
3-1346 L4PER_CM2 Registers Mapping Summary".
The secure clocks are part of the l4_per clock manager. As the l4_per
clock manager has now two clock domains as children, let's also update
the l4_per clockdomain node name to follow the "clock" node naming with
a domain specific compatible property.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We currently have a hidden dependency to the device tree node name for
the clkctrl clocks. Instead of using standard node name like "clock", we
must use "l4-per-clkctrl" type naming so the clock driver can find the
associated clock domain. Further, if "clk" is specified for a clock node
name, the driver sets TI_CLK_CLKCTRL_COMPAT flag that uses different
logic for the clock name based on the parent node name for the all the
clkctrl clocks for the SoC.
If the clock node naming dependency is not understood, the related
clockdomain is not found, or a wrong one can get used if a clock manager
has multiple clock domains.
As each clkctrl instance represents a single clock domain, let's allow
using domain specific compatible names to specify the clock domain.
This simplifies things and removes the hidden dependency to the node
name. And then later on, after the node names have been standardized,
we can drop the related code for parsing the node names.
Let's also update the binding to use standard "clock" node naming
instead of "clk" and add the missing description for reg.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is similar to what we have for omap5 except the gpu_cm address is
different, the mux clocks have one more source option, and there's no
divider clock.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "gpu-clkctrl@" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
For accessing the GPU, we also need to configure the interconnect target
module for GPU similar to what we have for omap5, I'll send that change
separately.
Cc: Benoit Parrot <bparrot@ti.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Looks like we're missing AESS clock for omap5. This is similar to what
omap4 has.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The parent clk for gmac clk ctrl has to be gmac_main_clk (125MHz) instead
of dpll_gmac_ck (1GHz). This is caused incorrect CPSW MDIO operation.
Hence, fix it.
Fixes: dffa9051d5 ('clk: ti: dra7: add new clkctrl data')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add clkctrl data for VPE.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add clkctrl data for CAM domain.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is not needed for anything, and prevents proper PM transitions for
parent devices which is bad in case of ti-sysc; this effectively kills
PM completely. Thus, remove the flag.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lkml.kernel.org/r/20191114101718.20619-1-peter.ujfalusi@ti.com
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Miquel Raynal