On GMAC4.xx each descriptor contains 2 buffers of 16KB (each).
Initially, those 2 buffers was filled in dwmac4_rd_prepare_tx_desc but
it is actually not needed. Indeed, stmmac driver supports frame up to
9000 bytes (jumbo). So only one buffer is needed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the PTP fpga to hps clock source for the stmmac module
the appropriate bit in the System Manager FPGA Interface Group register
needs to be set. This is not set by the bootloader setup when the
HPS emac pins are being for this emac module.
This allows the PTP clock to be sourced from the FPGA and also connects
the PTP pps and ext trig signals to the stmmac PTP hardware.
Patch proposed by Phil Collins.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
While initializing the phy, the stmmac driver sets the
PHY_IGNORE_INTERRUPT so the PAL won't call the adjust hook
that is needed, on some platforms, e.g. STi, to invoke the glue.
The patch allows the PAL to poll the stmmac_adjust_link just one time
in case of a switch is attached, setting later the PHY_IGNORE_INTERRUPT
flag.
Moving this kind of logic inside the adjust_link it makes sense to
anticipate the check for EEE that will never initialized in this
scenario.
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just updates the driver to the version fully
tested on STi platforms. This version is Jan_2016.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the whole GMAC4 support inside the
stmmac d.d. now able to use the new HW and some new features
i.e.: TSO.
It is missing the multi-queue and split Header support at this
stage.
This patch also updates the driver version and the stmmac.txt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to support the snps,dwmac-4.00 and snps,dwmac-4.10a
and related features on the platform driver.
See binding doc for further details.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For gmac3, the MMC addr map is: 0x100 - 0x2fc
For gmac4, the MMC addr map is: 0x700 - 0x8fc
So instead of adding 0x600 to the IO address when setup the mmc,
the RMON base address is saved inside the private structure and
then used to manage the counters.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the initial support for GMAC4 that includes
the main callbacks to setup the core module: including
Csum, basic filtering, mac address and interrupt (MMC,
MTL, PMT) No LPI added.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA behavior is linked to descriptor management:
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
-DMA_CH#_TxDesc_Tail_Pointer: address of the last
descriptor to send + 1.
-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
descriptor
-The descriptor Tail Pointer register contains the pointer to the
descriptor address (N). The base address and the current
descriptor decide the address of the current descriptor that the
DMA can process. The descriptors up to one location less than the
one indicated by the descriptor tail pointer (N-1) are owned by
the DMA. The DMA continues to process the descriptors until the
following condition occurs:
"current descriptor pointer == Descriptor Tail pointer"
Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new transfer:
"current descriptor pointer < Descriptor tail pointer"
The DMA automatically wraps around the base address when the end
of ring is reached.
Up to 8 DMA could be use but currently we only use one (channel0)
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the main header file to define all the
macro used for GMAC4 DMA and CORE parts.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of main changes of GMAC 4.xx IP is descriptors management.
-descriptors are only used in ring mode.
-A descriptor is composed of 4 32bits registers (no more extended
descriptors)
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor
ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
-DMA_CH#_TxDesc_Tail_Pointer: address of the last
descriptor to send + 1.
-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
descriptor
-The descriptor Tail Pointer register contains the pointer to the
descriptor address (N). The base address and the current
descriptor decide the address of the current descriptor that the
DMA can process. The descriptors up to one location less than the
one indicated by the descriptor tail pointer (N-1) are owned by
the DMA. The DMA continues to process the descriptors until the
following condition occurs:
"current descriptor pointer == Descriptor Tail pointer"
Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new
transfer:
"current descriptor pointer < Descriptor tail pointer"
The DMA automatically wraps around the base address when the end
of ring is reached.
-New features are available on IP:
-TSO (TCP Segmentation Offload) for TX only
-Split header: to have header and payload in 2 different buffers
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
synopsys_uid is only used once after setup, to get synopsys_id
by using shitf/mask operation. It's no longer used then.
So, remove this temporary variable and directly compute
synopsys_id from setup routine.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid lot of check in stmmac_main for display ring management
and support the GMAC4 chip, the display_ring function is moved
into dedicated descriptor file.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On next GMAC IP generation (4.xx), the way to get hw feature
is not the same than on previous 3.xx. As it is hardware
dependent, the way to get hw capabilities should be defined in dma ops of
each MAC IP. It will avoid also a huge computation of hw capabilities in
stmmac_main.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.
The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 88f8b1bb41.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixs a regression raised when test on chips that use
the normal descriptor layout. In fact, no len bits were set for
the TDES1 and no OWN bit inside the TDES0.
Signed-off-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a dt mdio entry has been added least assume that we wont
search for phys attached. The DT and of_mdiobus_register already do
this. This stops DSA phys being found and phys created for them, as
this is handled by the DSA driver.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:115:15-21: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch manages the case when you have an Ethernet MAC with
a "fixed link", and not connected to a normal MDIO-managed PHY device.
The test of phy_bus_name was not helpful because it was never affected
and replaced by the mdio test node.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just updates the driver to the version fully
tested on STi platforms. This version is Oct_2015.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a threshold now used to also limit the skb allocation
when use zero-copy. This is to avoid that there are incoherence
in the ring due to a failure on skb allocation under very
aggressive testing and under low memory conditions.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allow this driver to copy tiny frames during the reception
process. This is giving more stability while stressing the driver on STi
embedded systems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_bus_name can be NULL when "fixed-link" property isn't used.
Then, since "stmmac: do not poll phy handler when attach a switch",
phy_bus_name ptr needs to be checked before strcmp is called.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids to call the stmmac_adjust_link when
the driver is connected to a switch by using the FIXED_PHY
support. Prior this patch the phydev->irq was set as PHY_POLL
so periodically the phy handler was invoked spending useless
time because the link cannot actually change.
Note that the stmmac_adjust_link will be called just one
time and this guarantees that the ST glue logic will be
setup according to the mode and speed fixed.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fill the first descriptor just before granting
the DMA engine so at the end of the xmit.
The patch takes care about the algorithm adopted to mitigate the
interrupts, then it fixes the last segment in case of no fragments.
Moreover, this new implementation does not pass any "ter" field when
prepare the descriptors because this is not necessary.
The patch also details the memory barrier in the xmit.
As final results, this patch guarantees the same performances
but fixing a case if small datagram are sent. In fact, this
kind of test is impacted if no coalesce is done.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dirty index can be updated out of the loop where all the
tx resources are claimed. This will help on performances too.
Also a useless debug printk has been removed from the main loop.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch "inline" get_tx_owner and get_ls routines. It Results in a
unique read to tdes0, instead of three, to check TX_OWN and LS bits,
and other status bits.
It helps improve driver TX path by removing two uncached read/writes
inside TX clean loop for enhanced descriptors but not for normal ones
because the des1 must be read in any case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to optimize the way to manage the TDES inside the
xmit function. When prepare the frame, some settings (e.g. OWN
bit) can be merged. This has been reworked to improve the tx
performances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RDES0 register can be read several times while doing RX of a
packet.
This patch slightly improves RX path performance by reading rdes0
once for two operation: check rx owner, get rx status bits.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize tx_clean by avoiding a des3 read in stmmac_clean_desc3().
In ring mode, TX, des3 seems only used when xmit a jumbo frame.
In case of normal descriptors, it may also be used for time
stamping.
Clean it in the above two case, without reading it.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
last_segment field is read twice from dma descriptors in stmmac_clean().
Add last_segment to dma data so that this flag is from priv
structure in cache instead of memory.
It avoids reading twice from memory for each loop in stmmac_clean().
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the code pulls out the length field when
unmapping a buffer directly from the descriptor. This will result
in an uncached read to a dma_alloc_coherent() region. There is no
need to do this, so this patch simply puts the value directly into
a data structure which will hit the cache.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to rework the ring management now optimized.
The indexes into the ring buffer are always incremented, and
the entry is accessed via doing a modulo to find the "real"
position in the ring.
It is inefficient, modulo is an expensive operation.
The formula [(entry + 1) & (size - 1)] is now adopted on
a ring that is power-of-2 in size.
Then, the number of elements cannot be set by command line but
it is fixed.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch completely changes the descriptor layout to improve
the whole performances due to the single read usage of the
descriptors in critical paths.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.
After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.
For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to share the same reset procedure between dwmac100 and
dwmac1000 chips.
This will also help on enhancing the driver and support new chips.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally, most of the platforms using this driver did not define an mdio subnode
in the devicetree. Commit e34d65 ("stmmac: create of compatible mdio bus for stmmac driver")
introduced a backward compatibily issue by using of_mdiobus_register explicitly
with an mdio subnode. This patch fixes the issue by calling the function
mdiobus_register, when mdio subnode is not found. The driver is now compatible
with both modes.
Fixes: e34d65696d ("stmmac: create of compatible mdio bus for stmmac driver")
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides an options to use the ptp clock routed from the Altera FPGA
fabric. Instead of the defalt eosc1 clock connected to the ARM HPS core.
This setting affects all emacs in the core as the ptp clock is common.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_config_sub_second_increment set the sub second increment to 20ns.
Driver is configured to use the fine adjustment method where the sub second
register is incremented when the acculumator incremented by the addend
register wraps overflows. This accumulator is update on every ptp clk
cycle. If a ptp clk with a period of greater than 20ns was used the
sub second register would not get updated correctly.
Instead set the sub sec increment to twice the period of the ptp clk.
This result in the addend register being set mid range and overflow
the accumlator every 2 clock cycles.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA driver needs to be passed a reference to an mdio bus. Typically
the mac is configured to use a fixed link but the mdio bus still needs
to be registered so that it con configure the switch.
This patch follows the same process as the altera tse ethernet driver for
creation of the mdio bus.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dwmac-sunxi has 2 callbacks that were called from stmmac_platform as
part of the probe and remove sequences.
Ater the conversion of dwmac-sunxi into a standalone platform driver,
the .init function is called before calling into the stmmac driver
core, but .exit is not called to clean up if stmmac returns an error.
This patch fixes the probe error path. This properly cleans up and
releases resources when the driver core fails to probe.
Cc: Joachim Eastwood <manabian@gmail.com>
Fixes: 9a9e9a1ede ("stmmac: dwmac-sunxi: turn setup callback into a
probe function")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a memleak when suspend/resume this driver version.
Currently the stmmac, during resume step, reallocates all the resources
but they are not released when suspend.
The patch is not to release these resources but the logic has been changed.
In fact, it is not necessary to free and reallocate all from scratch
because the memory data will be always preserved.
As final solution, the patch just reinit the descriptors and the rx/tx
pointers only when resume. Tested done on STi boxes.
Reported-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Typically we return error pointers when we want to use those
pointers in the non-error case, but this function is just
returning error pointers or NULL for success. Change the style to
plain int to follow normal kernel coding styles.
Cc: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For GMAC newer than 3.40a there is a new register (Reg_9) that provides the
status of all modules of the transmit and receive paths and FIFO status.
These can be exposed via ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive skb buffers can be preallocated when the link is opened
according to mtu size.
While testing on a network environment with not standard MTU (e.g. 3000),
a panic occurred if an incoming packet had a length greater than rx skb
buffer size. This is because the HW is programmed to copy, from the DMA,
an Jumbo frame and the Sw must check if the allocated buffer is enough to
store the frame.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stmmac_mdio_reset, was called from stmmac_resume, it was not
resetting the PHY due to which MAC was not getting reset properly and
hence ethernet interface not was resumed properly.
The issue was currently only reproducible on stih301-b2204.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of the st,tx-retime-src is missing from device-tree
(it's an optional field) the driver will invoke the strcasecmp to check
which clock has been selected and this is a bug; the else condition
is needed.
In the dwmac_setup, the "rs" variable, passed to the strcasecmp, was not
initialized and the compiler, depending on the options adopted, could
take it in some different part of the stack generating the hang in such
configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the csr clock in case of 300MHz is provided.
Reported-by: Kent Borg <Kent.Borg@csr.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resume the HW is re-configured but some settings can be lost.
For example, the MAC Address_X High/Low Registers used for VLAN tagging..
So, while resuming, the set_filter callback needs to be invoked to
re-program perfect and hash-table registers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building dwmac-ipq806x on a 64-bit architecture produces a harmless
warning from gcc:
stmmac/dwmac-ipq806x.c: In function 'ipq806x_gmac_probe':
include/linux/bitops.h:6:19: warning: overflow in implicit constant conversion [-Woverflow]
val = QSGMII_PHY_CDR_EN |
stmmac/dwmac-ipq806x.c:333:8: note: in expansion of macro 'QSGMII_PHY_CDR_EN'
#define QSGMII_PHY_CDR_EN BIT(0)
#define BIT(nr) (1UL << (nr))
This is a result of the type conversion rules in C, when we take the
logical OR of multiple different types. In particular, we have
and unsigned long
QSGMII_PHY_CDR_EN == BIT(0) == (1ul << 0) == 0x0000000000000001ul
and a signed int
0xC << QSGMII_PHY_TX_DRV_AMP_OFFSET == 0xc0000000
which together gives a signed long value
0xffffffffc0000001l
and when this is passed into a function that takes an unsigned int type,
gcc warns about the signed overflow and the loss of the upper 32-bits that
are all ones.
This patch adds 'ul' type modifiers to the literal numbers passed in
here, so now the expression remains an 'unsigned long' with the upper
bits all zero, and that avoids the signed overflow and the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b1c17215d7 ("stmmac: add ipq806x glue layer")
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable phy_iface is double-initialized to itself.
This patch remove that.
Reported-by: coverity (CID 1271141)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
priv->hwts_*_en indicate if timestamping is enabled/disabled at run
time. But priv->dma_cap.time_stamp and priv->dma_cap.atime_stamp
indicates HW is support for PTPv1/PTPv2.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to deprecate the use of 'struct timespec' on 32-bit
architectures, as it is will overflow in 2038. The stmmac
driver uses it to read the current time, and can simply
be changed to use ktime_get_real_ts64() instead.
Because of hardware limitations, there is still an overflow
in year 2106, which we cannot really avoid, but this documents
the overflow.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable can store negative values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset delays used for stmmac are in the order of 10ms to 1 second,
which is far too long for udelay usage, so switch to using msleep.
Practically this fixes the PHY not being reliably detected in some cases
as udelay wouldn't actually delay for long enough to let the phy
reliably be reset.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current check of phydev with IS_ERR(phydev) may make not much sense
because of_phy_connect() returns NULL on failure instead of error value.
Still for checking result of phy_connect() IS_ERR() makes perfect sense.
So let's use combined check IS_ERR_OR_NULL() that covers both cases.
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch b1c17215d718: "stmmac: add ipq806x glue layer", leads to the
following static checker warning:
.../stmmac/dwmac-ipq806x.c:314 ipq806x_gmac_probe()
warn: double left shift '1 << (1 << gmac->id)'
The NSS_COMMON_CLK_SRC_CTRL_OFFSET macro is used once as an offset, and
once as a mask, which is a bug indeed. We'll fix it by defining the
offset as the real offset value and computing the mask from it when
required.
Tested on IPQ806x ref designs AP148 & DB149.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 50649ab149 ("stmmac: drop driver from stmmac platform code")
was a bit overzealous in removing code and dropped the MODULE_*
macro's that are still needed since stmmac_platform can be a module.
Fix this by putting the macro's remvoed in 50649ab149 back.
This fixes the following errors when used as a module:
stmmac_platform: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
stmmac_platform: Unknown symbol devm_kmalloc (err 0)
stmmac_platform: Unknown symbol stmmac_suspend (err 0)
stmmac_platform: Unknown symbol platform_get_irq_byname (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0)
stmmac_platform: Unknown symbol platform_get_resource (err 0)
stmmac_platform: Unknown symbol of_get_phy_mode (err 0)
stmmac_platform: Unknown symbol of_property_read_u32_array (err 0)
stmmac_platform: Unknown symbol of_alias_get_id (err 0)
stmmac_platform: Unknown symbol stmmac_resume (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0)
Fixes: 50649ab149 ("stmmac: drop driver from stmmac platform code")
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the two platform specific init callbacks and make
them use a common one by creating a function member in
the internal data structure. This allow us to remove the
layer of indirection and simplify the code a bit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all dwmac-* drivers have been converted to have a proper probe
function the setup callback can now be removed. Also remove the
free callback that wasn't used by any driver.
New dwmac-* drivers should implement standard probe and remove
functions to preform any needed setup and teardown.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the setup glue callback and use rk_gmac_ops as OF match
data so it can used directly when calling rk_gmac_setup.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark the rk_gmac_ops structures as static const as they should be.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new private structure for OF match data in the
dwmac-sti driver. This enables us to eventually drop the
common OF match data structure which contains a lot of
unused fields.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since only a few of the dwmac-* drivers actually need to use
the OF match move handling into the dwmac-* drivers that need
it. This will also allow dwmac-* drivers to use their own
custom match data structure.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all dwmac-* drivers now have their own probe function move
the common one into dwmac-generic driver and drop the EXPORT.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new probe functions that call the necessary setup
functions. This is done in preparation for a code refactor
in this driver and dropping the common probe function in
stmmac_platform.c.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and prepares the
driver for further clean ups.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move sun7i_gmac_setup in preparation for turning it into
a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move socfpga_dwmac_probe in preparation for turning it into
a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform a proper probe
function can be created from the setup glue callback. This
makes it look more like a standard driver and the OF match
data can also be dropped.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ipq806x_gmac_fix_mac_speed in preparation for turning
the setup glue callback in a proper probe function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:304:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[je: rebase and insert newline before return]
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 803f8fc462 ("stmmac: move driver data setting into
stmmac_dvr_probe") mistakenly set priv and not priv->dev as
driver data. This meant that the remove, resume and suspend
callbacks that fetched and tried to use this data would most
likely explode. Fix the issue by using the correct variable.
Fixes: 803f8fc462 ("stmmac: move driver data setting into stmmac_dvr_probe")
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform we can now create
a proper probe function in this driver. By doing so we can drop
the OF match data and simplify the overall driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few functions from stmmac_platform we can now create
a proper probe function in this driver. By doing so we can drop
the OF match data and simplify the overall driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export stmmac_probe_config_dt() and stmmac_get_platform_resources()
so they can be used in the dwmac-* drivers themselves. This will
allow us to build more flexible and standalone drivers which just
use stmmac_platform as a library for setup functions.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since stmmac_probe_config_dt() allocates the platform data structure
it is cleaner if it just returned this structure directly. This
function will later be used in the probe function in dwmac-* drivers.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor all code that deals with platform resources into it's
own get function. This function will later be used in the probe
function in dwmac-* drivers.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor code to clearly separate probing non-dt versus dt. In the
non-dt case platform data must be supplied to probe successfully.
For dt the platform data structure is created and match data is
copied into it. Note that support for supplying platform data in
dt from AUXDATA is dropped as no users in mainline does this.
This change will allow dt dwmac-* drivers to call the config_dt()
function from probe to create the needed platform data struct and
retrieve common dt properties.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using of_device_get_match_data() the code that retrieve
match data can be simplified quite a bit.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of descriptor init procedure only takes
care about setting/clearing ownership flag in "des0"/"des1"
fields while it is perfectly possible to get unexpected bits
set because of the following factors:
[1] On driver probe underlying memory allocated with
dma_alloc_coherent() might not be zeroed and so
it will be filled with garbage.
[2] During driver operation some bits could be set by SD/MMC
controller (for example error flags etc).
And unexpected and/or randomly set flags in "des0"/"des1"
fields may lead to unpredictable behavior of GMAC DMA block.
This change addresses both items above with:
[1] Use of dma_zalloc_coherent() instead of simple
dma_alloc_coherent() to make sure allocated memory is
zeroed. That shouldn't affect performance because
this allocation only happens once on driver probe.
[2] Do explicit zeroing of both "des0" and "des1" fields
of all buffer descriptors during initialization of
DMA transfer.
And while at it fixed identation of dma_free_coherent()
counterpart as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE