[ Upstream commit 74e1c956a68a65d642447d852e95b3fbb69bebaa ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b972d6b3b46345023aee56a95df8e2c137aa4ee4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edfea889a049abe80f0d55c0365bf60fbade272f ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae1 ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98c ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0df3c7d7a73d75153090637392c0b73a63cdc24a ]
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98c ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4306c047415a227bc72f0e7ba9bde1ccdac10435 ]
STM32MP15xx RM0436 Rev 6 section 46.3 System timer generator (STGEN) states
"
Arm recommends that the system counter is in an always-on power domain.
This is not supported in the current implementation, therefore STGEN should
be saved and restored before Standby mode entry, and restored at Standby
exit by secure software.
...
"
Instead of piling up workarounds in the firmware which is difficult to
update, add "arm,no-tick-in-suspend" DT property into the timer node to
indicate the timer is stopped in suspend, and let the kernel fix the
timer up.
Fixes: 8471a20253 ("ARM: dts: stm32: add stm32mp157c initial support")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cca46f811d0000c1522a5e18ea48c27a15e45c05 ]
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3066a.dtsi'.
Fixes: fadc780624 ("ARM: dts: rockchip: add rk3066 hdmi nodes")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/8b229dcc-94e4-4bbc-9efc-9d5ddd694532@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 88208d3cd79821117fd3fb80d9bcab618467d37b upstream.
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-origen.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: bd08f6277e ("ARM: dts: Add keypad entries to Exynos4412 based Origen")
Link: https://lore.kernel.org/r/20240312183105.715735-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ac4c1d794e7ff454d191bbdab7585ed8dbf3758 upstream.
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-smdk4412.dtb: keypad@100a0000: 'key-A', 'key-B', 'key-C', 'key-D', 'key-E', 'linux,keypad-no-autorepeat' do not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: c9b92dd701 ("ARM: dts: Add keypad entries to SMDK4412")
Link: https://lore.kernel.org/r/20240312183105.715735-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87d8e522d6f5a004f0aa06c0def302df65aff296 upstream.
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4210-smdkv310.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: 0561ceabd0 ("ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN")
Link: https://lore.kernel.org/r/20240312183105.715735-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e027b71762e84ee9d4ba9ad5401b956b9e83ed2a ]
By checking the pmic node with microchip,mcp16502.yaml#
'regulator-suspend-voltage' does not match any of the
regexes 'pinctrl-[0-9]+' from schema microchip,mcp16502.yaml#
which inherits regulator.yaml#. So replace regulator-suspend-voltage
with regulator-suspend-microvolt to avoid the inconsitency.
Fixes: 85b1304b9d ("ARM: dts: at91: sama7g5ek: set regulator voltages for standby state")
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240404123824.19182-2-andrei.simion@microchip.com
[claudiu.beznea: added a dot before starting the last sentence in commit
description]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 585e4dc07100a6465b3da8d24e46188064c1c925 ]
Fix rk3288 hdmi ports node so that it matches the
rockchip,dw-hdmi.yaml binding with some reordering
to align with the (new) documentation about
property ordering.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/cc3a9b4f-076d-4660-b464-615003b6a066@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 831e0cd4f9ee15a4f02ae10b67e7fdc10eb2b4fc ]
Fix an obvious spelling error in the PMIC compatible in the MMP2
Brownstone DTS file.
Fixes: 58f1193e62 ("mfd: max8925: Add dts")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Closes: https://lore.kernel.org/linux-devicetree/1410884282-18041-1-git-send-email-k.kozlowski@samsung.com/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125-brownstone-typo-fix-v2-1-45bc48a0c81c@skole.hr
[krzysztof: Just 10 years to take a patch, not bad! Rephrased commit
msg]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79978bff2e4b8e05ebdf5fc3ee6b794002393484 ]
We identified that the PHYs actually do not work since commit 7da7b84fee
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 023bd910d3ab735459f84b22bb99fb9e00bd9d76 ]
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497f ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3baa4c5143d65ebab2de0d99a395e5f4f1f46608 ]
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 724c4bf0e4bf81dba77736afb93964c986c3c123 ]
The qfprom actually is bigger than 0x1000, so adjust the reg.
Note that the non-ECC-corrected qfprom can be found at 0xfc4b8000
(-0x4000). The current reg points to the ECC-corrected qfprom block
which should have equivalent values at all offsets compared to the
non-corrected version.
[luca@z3ntu.xyz: extract to standalone patch and adjust for review
comments]
Fixes: c59ffb5193 ("arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240210-msm8974-qfprom-v3-1-26c424160334@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 090c4094574705b0afc7d37825cdc5d06f0e7e02 ]
External clocks should be defined as zero-Hz clocks in the SoC .dtsi,
and overridden in the board .dts when present.
Correct the clock rate of extal1 from 25 to 26 MHz, to match the crystal
oscillator present on the APE6-EVM board.
Fixes: a76809a329 ("ARM: shmobile: r8a73a4: Common clock framework DT description")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/1692bc8cd465d62168cbf110522ad62a7af3f606.1705315614.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f02b0f0dc26fbb77fe47b6e47cc5c211f0432c37 ]
The dtc interrupt_map warning is off because its dependency,
interrupt_provider, is off by default. Fix all the warnings so it can be
enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-4-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96fd598e9c34cfa68402a4da3020c9236cfacf35 ]
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-2-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f98643d8daf3443e3b414a82d0cb3d745f8c8bbc ]
The binding doesn't define interrupts and adding such a definition was
refused because it's unclear how they should ever be used and the
relevant registers are outside the PWM range. So drop them fixing
several dtbs_check warnings like:
arch/arm/boot/dts/rockchip/rv1108-elgin-r1.dtb: pwm@10280030: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/pwm/pwm-rockchip.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240129113205.2453029-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858d83ca4b50bbc8693d95cc94310e6d791fb2e6 ]
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aa1a82fb20ee97597022f6528823a8ab82bde6 ]
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc35e253d032b959d92e12f081db5b00db26ae64 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11ab7ad6f795ae23c398a4a5c56505d3dab27c4c ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0b929f58719fc57a4926ab4fc972f185453d6a5 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c248e535973088ba7071ff6f26ab7951143450af ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fb7b2a2f06bb3f8321cf26c33e4e820c5b238b6 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1d7cc478fb16816de09740e3c323c0c188d58f ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c711b882c262e36895547cddea2c2d56ce611d ]
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f55da4cc37051cda600ea870ce8cf29f1297715 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d4ac04fa7c3f6dc263dba6f575a2ec7a2d4eca8 ]
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07e6a553c2f1d385edfc9185081dee442a9dd38d ]
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@fa600000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@fa600000: missing or empty reg/ranges property
Subtract 0xfa600000 from all its children nodes. No functional impact
expected.
Link: https://lore.kernel.org/r/20230722121719.150094-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba2a45a48503665f7e8eeec51f8b40456566b0cd ]
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@11800000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@11800000: missing or empty reg/ranges property
Subtract 0x11800000 from all its children nodes. No functional impact
expected.
Link: https://lore.kernel.org/r/20230722121719.150094-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 455a4c46e023ab84263eae0fc7acca9a5ee8b7ac ]
As the vendor DTS files were moved to per-vendor subdirs, there no need
to use common prefixes. Drop the `qcom-' prefix from PMIC dtsi file.
This makes 32-bit qcom/ dts files closer to arm64 ones.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928110309.1212221-8-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eab4f56d3e75dad697acf8dc2c8be3c341d6c63e ]
After more investigation, I've found that it's not the panel driver
config that needs to be modified to invert the data polarity, but
the FIMD config.
Add the missing invert-vclk option that is required to get the display
to work correctly.
Fixes: ee37a457af ("ARM: dts: exynos: Add Samsung Galaxy Tab 3 8.0 boards")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20240105-tab3-display-fixes-v2-1-904d1207bf6f@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 710dd03464e4ab5b3d329768388b165d61958577 upstream.
The USB SS PHY interrupt needs to be provided by the PDC interrupt
controller in order to be able to wake the system up from low-power
states.
Fixes: fea4b41022 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-4-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de95f139394a5ed82270f005bc441d2e7c1e51b7 upstream.
The USB DP/DM HS PHY interrupts need to be provided by the PDC interrupt
controller in order to be able to wake the system up from low-power
states and to be able to detect disconnect events, which requires
triggering on falling edges.
A recent commit updated the trigger type but failed to change the
interrupt provider as required. This leads to the current Linux driver
failing to probe instead of printing an error during suspend and USB
wakeup not working as intended.
Fixes: d0ec3c4c11c3 ("ARM: dts: qcom: sdx55: fix USB wakeup interrupt types")
Fixes: fea4b41022 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84228d5e29dbc7a6be51e221000e1d122125826c upstream.
The kernel hangs for a good 12 seconds without any info being printed to
dmesg, very early in the boot process, if this regulator is not enabled.
Force-enable it to work around this issue, until we know more about the
underlying problem.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 8620cc2f99 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Cc: stable@vger.kernel.org # v5.8+
Link: https://lore.kernel.org/r/20231206221556.15348-2-paul@crapouillou.net
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Walle