- let role driver handle irq before ID change check; this gives the
role driver a chance to handle disconnect;
- disable irq during switch role; no role driver to handle irq in
the period.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch turns on debugging output if CONFIG_USB_CHIPIDEA_DEBUG is
enabled.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using vbus valid interrupt to detect vbus.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to avoid re-queueing of the role changing work, we need to clear
the ID change interrupt bit right in the irq handler.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ID pin needs 1ms debounce time, even at probe time. We delay 2ms
to be on the safe side.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some controllers may not need to setup pinctrl, so we don't fail the
probe if pinctrl get/select failed.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX usb controllers share non-core registers, which may include
SoC specific controls. We turn it into a usbmisc device and usbmisc
driver set operations needed by ci13xxx_imx driver.
For example, Sabrelite board has bad over-current design, we can
usbmisc to disable over-current detection.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These chipidea stable patches are needed for other chipidea patches to be
applied properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:
g_ether gadget: high speed config #2: RNDIS
Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.
This patch removed this check, because the code doesn't take the following
situation into account:
The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.
Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the error path of udc_start(). Now NULL is used to
unset the peripheral with otg_set_peripheral().
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add function to physicaly enable or disable of pullup connection on the USB-D+
line. The uvc gaget will fail, if this function is not implemented.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the setup of the endpoint maxpacket size. All non control
endpoints are initialized with an undefined ((unsigned short)~0) maxpacket
size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX.
Some gadget drivers check for the maxpacket size before they enable the
endpoint, which leads to a wrong state in these drivers.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ff823c79a5 ("usb: move children
to struct usb_port") forgot to consider the hub_disconnect sequence,
which releases ports before quiescing the hub, which will lead to a
use-after-free, since hub_quiesce() will try to disconnect ports'
children, which are already deallocated. Simple modprobe dummy_hcd &&
rmmod dummy_hcd will illustrate the problem.
This patch moves deallocation of hub's ports after hub_quiesce() call
in hub_disconnect().
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.
We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.
Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.
All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UHPu
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: musb: patches for v3.7 merge window
Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.
We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.
Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.
All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.
Some much needed changes for our dwc3 driver. First there's a
rework on the ep0 handling due to some Silicon issue we uncovered
which affects all users of this IP core (there's a missing
XferNotReady(DATA) event in some conditions). This issue which
show up as a SETUP transfers which wouldn't complete ever and
we would fail TD 7.06 of the Link Layer Test from USB-IF and
Lecroy's USB3 Exerciser.
We also fix a long standing bug regarding EP0 enable sequencing
where we weren't setting a particular bit (Ignore Sequence
Number). Since we never saw any problems caused by that, it
didn't deserve being sent to stable tree.
On this pull request we also fix Burst Size initialization which
should be done only in SuperSpeed and we were mistakenly setting
Burst Size to the maximum value on non-SuperSpeed mode. Again,
since we never saw any problems caused by that, we're not sending
this patch to stable.
There's also a memory ordering fix regarding usage of bitmaps in
dwc3 driver.
You will also find some sparse warnings fix, a fix for missed
isochronous packets when the endpoint is already busy, and a
fix for synchronization delay on dwc3_stop_active_transfer().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQThLOAAoJEIaOsuA1yqREPB0P/igbry8UxYEfFA6+ojRmeS3x
AztAUUixXsl44lQOLtl/VSuKqvhiIJ7VniBgL+nj1HdeJPMG6bdjBLwl2LjYBCQq
xZbv07isqHqg8ntiGwOADQztU7p4BPGpDztogsTlNjUhclCvUwE9ZTf4Moe7Cnk8
TePUypvt3WQceWBpZxMd9Zirpmls0UTUW287OgQ+ik6QccokzQXxfzD5z3tS0bwo
nRjWReihPJU68p5wcbILjo4VmhBsllYrRxB8CIatqxfjj6OssJ0ifcO6+jn7bnc5
T8OStPK8FigTLdNuV4sx3MCu9ItSY1+Y+gRnfXpdbkEqU303qI/rOC0jnmEhAhr1
/mS9llhCkfknpvL/DSlQnYzwfNA4wFjTLNoxOEDNkYNE84T+YAfZI1DGBvwJoYlZ
NELQTJB2enVADmMyOwQcXwx7wu2uW7Sb6FcbYpIsZyADZVJPqtjG1o09d19xL0z5
YdP23D/A6/I6SySvW8cDy9F3ouCQfrkeEd71KF2+4s7zHZhU9cqFA65xOZ7FRB++
nUsTHCn07doqp+5vsRLV0BKPk3YH9mEg0aVv4ClSE57wZFPFAqXU5GtEgJ9mBAnv
3poV22oTvGdWuG3vzAAk83pnQPyxxv4DgDLc3gaKZXhecLDRp0O4uucuHrmyV5tn
eynhmX9bDB5hLGN5KJtX
=Lqwl
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.7 merge window
Some much needed changes for our dwc3 driver. First there's a
rework on the ep0 handling due to some Silicon issue we uncovered
which affects all users of this IP core (there's a missing
XferNotReady(DATA) event in some conditions). This issue which
show up as a SETUP transfers which wouldn't complete ever and
we would fail TD 7.06 of the Link Layer Test from USB-IF and
Lecroy's USB3 Exerciser.
We also fix a long standing bug regarding EP0 enable sequencing
where we weren't setting a particular bit (Ignore Sequence
Number). Since we never saw any problems caused by that, it
didn't deserve being sent to stable tree.
On this pull request we also fix Burst Size initialization which
should be done only in SuperSpeed and we were mistakenly setting
Burst Size to the maximum value on non-SuperSpeed mode. Again,
since we never saw any problems caused by that, we're not sending
this patch to stable.
There's also a memory ordering fix regarding usage of bitmaps in
dwc3 driver.
You will also find some sparse warnings fix, a fix for missed
isochronous packets when the endpoint is already busy, and a
fix for synchronization delay on dwc3_stop_active_transfer().
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQThmRAAoJEIaOsuA1yqRE2U4P+gJHJsQZUIqTkCi6GyutMLUX
HUYVgaCXAbt4sSB5s0OK7AsB8uQ82GO6ZGyPfxNlYr6LXYlQWZ1OIig8PNhyn4en
lt0TolGL53fDOrwvQ0MIJBB1rgCk81UoFwJaPYkhKDNQLndl4hxlrFTsAvaIu7H0
pMMLt3E0Jz7018NxvVN23OV3EXnb2GF9K2Jt/NJNkZPanJaWXz0T/6DvBG24du2x
t3ALiKnpAC51wHPB5T88tefmVNApz7DPwK/Bm/VKW66LZ61Y+nZtZ+QMxj//uTt9
c3JXCvGscKSBcSfSFNMeYBdiPOZIFXTRVLr7CzxplvY9j5u8DTGArz5nvj/8ajbW
OeU0DMMaStfFqd12/BFUQeixbH8NUSoR5luWVMzBhB5+MF493gHvsu2ooorpR2hP
jQgMY146RdVbXNDJmuLRlVZbHQZfJBqvVUpk+3mdSSOtpy4IpKvlzPkYL1YjyOMt
x8WF+shSBvOMhg5C/HlGbDLzTiTv8zWef/aJ7OP9yUwYIz/map3lax749+M0Yzcj
trQgbLYrc8OeMVuCYGqjw1m96/YmcIxvzI/OnAMPbrPxK2hjy5jAu64/gOAZiZNY
oQis5G5qw/24LkXfLNQFTl8nYmaDko03+wazCg39D11bWZbLgKs9YJPZd78EwpJy
s+gU0+RYAQHgo+EChLY+
=/qVp
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: xceiv: patches for v3.7 merge window
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
This pull request is large but the biggest part is the first part
of the cleanup on the gadget framework so we have a saner setup
to add configfs support for v3.8.
We have also some more conversions to the new udc_start/udc_stop
which makes us closer from dropping the old interfaces.
USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED are finally gone,
thanks to Michal for his awesome work.
Other than that, we have the usual set of miscellaneous changes
and cleanups involving improvements to debug messages, removal
of duplicated includes, moving dereference after NULL test,
making renesas_hsbhs' irq handler Shared, unused code being dropped,
prevention of sleep-inside-spinlock bugs and a race condition fix
on udc-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQTh3DAAoJEIaOsuA1yqRE+DIQAIwDRDojG3WLpMq7RJJQclS6
4Uk1wkim/DxlJsXDvhGd/Qecr6Gk8HSX6hFBg0u2t9g5csl42kTa7PGCN8XSgAC9
yekqDbjewkdTy5ar6y06LfFObiq3ubL489AW1p0Sk8t7xPZIwYa18nthLcr955SU
i0enMctQ4wuO2OParBoEECjui2ZGD6WUnlLBJP5dR1ALgefl77d93H5wzxZsjJMX
zrYsG5MLLz8SyZGgHL7H9e+ydLeLC9zwl2a6PiLMTg1m3E3/wlb+yzjOe/XFubxZ
VCrRPvDXsTkCohwGA6rovcLZIxMiBDdjwpYzXMKqfwwePs2DrC9BzxX2n7P0hI/J
QlroU/4mj4/xoc6Z/JMxBo0cK8PUhVfmlNt1Y77K40mbSGjwOUL9r905fPOcW1cL
5QjWi7b4XVqp+tCcY7epckN4yivkurXPSFjqoG1DV2RAmY8CXH2uDYp7ZJyxn3BT
7yMxdGfm4IUgvJbET38Bs7mM9EYn7oFBZMfNOJ4yeYYBZ5wCnx5V0bWmyP9SHoDn
HUmOD8/NQ91Lafx+qDH86TC0Yi9LMRfyLg0jncVyrF4Mq6R7KPgNHFEjDDUw4OxE
6mskECsORKnQZ7GNe+0/r9Ke8Qy1dmhtQ1mUaKn3GcRwTFveGB4cXJf9yvCFid5Y
bOPKKoCFpy7W+ncZ4WDX
=T3kf
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: gadget: patches for v3.7 merge window
This pull request is large but the biggest part is the first part
of the cleanup on the gadget framework so we have a saner setup
to add configfs support for v3.8.
We have also some more conversions to the new udc_start/udc_stop
which makes us closer from dropping the old interfaces.
USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED are finally gone,
thanks to Michal for his awesome work.
Other than that, we have the usual set of miscellaneous changes
and cleanups involving improvements to debug messages, removal
of duplicated includes, moving dereference after NULL test,
making renesas_hsbhs' irq handler Shared, unused code being dropped,
prevention of sleep-inside-spinlock bugs and a race condition fix
on udc-core.
As NOP device node is now added in am33xx tree so remove the call
which creates the NOP platform_device.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added device tree support for dsps musb glue driver and updated the
Documentation with device tree binding information.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[afzal@ti.com: use '-' instead of '_' for dt properties]
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AM335x and TI81xx platform has dual musb controller so updating the
musb_dspc.c to support the same.
Changes:
- Moved otg_workaround timer to glue structure
- Moved static local variable last_timer to glue structure
- PHY on/off related cleanups
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
[afzal@ti.com: remove control module related modifications]
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Moved global variable "musb_debugfs_root" and static variable
"old_state" to 'struct musb' to help support multi instance of
musb controller as present on AM335x platform.
Also removed the global variable "orig_dma_mask" and filled the
dev->dma_mask with parent device's dma_mask.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added musb_ida in musb_core.c to manage the multi core ids.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The glue layer should directly write to mailbox register (present in
control module) instead of calling phy layer to write to mailbox
register. Writing to mailbox register notifies the core of events like
device connect/disconnect.
Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Because the IRQF_DISABLED as the flag is now a NOOP and has been
deprecated and in hardirq context the interrupt is disabled.
so in usb/host code:
Removing the usage of flag IRQF_DISABLED;
Removing the calling local_irq save/restore actions in irq
handler usb_hcd_irq();
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds two sysfs files for each usb hub port to allow userspace
to control the port power policy.
For an upcoming Intel xHCI roothub, this will translate into ACPI calls
to completely power off or power on the port. As a reminder, when these
ports are completely powered off, the USB host and device will see a
physical disconnect. All future USB device connections will be lost,
and the device will not be able to signal a remote wakeup.
The control sysfs file can be written to with two options:
"on" - port power must be on.
"off" - port must be off.
The state sysfs file reports usb port's power state:
"on" - powered on
"off" - powered off
"error" - can't get power state
For now, let userspace dictate the port power off policy. Future
patches may add an in-kernel policy.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern pointed out that a USB port could potentially get powered off
when the attached USB device is in the middle of enumerating, due to
race conditions:
http://marc.info/?l=linux-usb&m=134130616707548&w=2
If that happens, we need to ensure the enumeration fails. If a call to
usb_get_descriptor() fails for a reason other than a Stall, return an
error. That should handle the case where the port is powered off.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upcoming Intel systems will have an ACPI method to control whether a USB
port can be completely powered off. The implication of powering off a
USB port is that the device and host sees a physical disconnect, and
subsequent port connections and remote wakeups will be lost.
Add a new function, usb_acpi_power_manageable(), that can be used to
find whether the usb port has ACPI power resources that can be used to
power on and off the port on these machines. Also add a new function
called usb_acpi_set_power_state() that controls the port power via these
ACPI methods.
When the USB core calls into the xHCI hub driver to power off a port,
check whether the port can be completely powered off via this new ACPI
mechanism. If so, call into these new ACPI methods. Also use the ACPI
methods when the USB core asks to power on a port.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the xHCI roothub code handle the clear PORT_POWER
feature request. Setting port power is already handled.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the upcoming USB port power off patches, we need to know whether a
USB port can ever see a disconnect event. Often USB ports are internal
to a system, and users can't disconnect USB devices from that port.
Sometimes those ports will remain empty, because the OEM chose not to
connect an internal USB device to that port.
According to ACPI Spec 9.13, PLD indicates whether USB port is
user visible and _UPC indicates whether a USB device can be connected to
the USB port (we'll call this "connectible"). Here's a matrix of the
possible combinations:
Visible Connectible
Name Example
-------------------------------------------------------------------------
Yes No Unknown (Invalid state.)
Yes Yes Hot-plug USB ports on the outside of a laptop.
A user could freely connect and disconnect
USB devices.
No Yes Hard-wired A USB modem hard-wired to a port on the
inside of a laptop.
No No Not used The port is internal to the system and
will remain empty.
Represent each of these four states with an enum usb_port_connect_type.
The four states are USB_PORT_CONNECT_TYPE_UNKNOWN,
USB_PORT_CONNECT_TYPE_HOT_PLUG, USB_PORT_CONNECT_TYPE_HARD_WIRED, and
USB_PORT_NOT_USED. When we get the USB port's acpi_handle, store the
state in connect_type in struct usb_port.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ACPI DSDT table, only usb root hub and usb ports are ACPI device
nodes. Originally, we bound the usb port's ACPI node to the usb device
attached to the port. However, we want to access those ACPI port
methods when the port is empty, and there's no usb_device associated
with that port.
Now that the usb port is a real device, we can bind the port's ACPI node
to struct usb_port instead.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_device structure contains an array of usb_device "children".
This array is only valid if the usb_device is a hub, so it makes no
sense to store it there. Instead, store the usb_device child
in its parent usb_port structure.
Since usb_port is an internal USB core structure, add a new function to
get the USB device child, usb_hub_find_child(). Add a new macro,
usb_hub_get_each_child(), to iterate over all the children attached to a
particular USB hub.
Remove the printing the USB children array pointer from the usb-ip
driver, since it's really not necessary.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch turns each USB port on a hub into a new struct device. This
new device has the USB hub interface device as its parent. The port
devices are stored in a new structure (usb_port), and an array of
usb_ports are dynamically allocated once we know how many ports the USB
hub has.
Move the port_owner variable out of usb_hub and into this new structure.
A new file will be created in the hub interface sysfs directory, so
add documentation.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel's version number is used as decimal in the bcdDevice field of
the RH descriptor. For kernel version v3.12 we would see 3.0c in lsusb.
I am not sure how important it is to stick with bcd values since this is
this way since we started git history and nobody complained (however back
then we reported only 2.6).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apps which deal with devices which also have a kernel driver, need to do
the following:
1) Check which driver is attached, so as to not detach the wrong driver
(ie detaching usbfs while another instance of the app is using the device)
2) Detach the kernel driver
3) Claim the interface
Where moving from one step to the next for both 1-2 and 2-3 consists of
a (small) race window. So currently such apps are racy and people just live
with it.
This patch adds a new ioctl which makes it possible for apps to do this
in a race free manner. For flexibility apps can choose to:
1) Specify the driver to disconnect
2) Specify to disconnect any driver except for the one named by the app
3) Disconnect any driver
Note that if there is no driver attached, the ioctl will just act like the
regular claim-interface ioctl, this is by design, as returning an error for
this condition would open a new bag of race-conditions.
Changes in v2:
-Fix indentation of if blocks where the condition spans multiple lines
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fengguang Wu reported:
|drivers/usb/gadget/serial.c:89:22: sparse: cast truncates bits from
|constant value (24000000 becomes 0)
I obviously let the version number shift away. Since the version is a
16bit number it can be applied as it.
Cc: fengguang.wu@intel.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently mx23 fails to enumerate a USB device:
[ 1.300000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.520000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.740000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.960000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 2.180000] hub 1-0:1.0: unable to enumerate USB device on port 1
Use a kernel workqueue to asynchronously delay the setting of
ENHOSTDISCONDETECT bit until after higher level hub connect/reset processing
is complete. Prematurely setting the bit prevents the connection
processing from completing and not setting it prevents disconnect from being
detected. No delay is needed for clearing of ENHOSTDISCONDETECT.
Successfully tested on mx23-olinuxino (micro, mini and maxi variants) and mx28evk.
Cc: stable@vger.kernel.org # v3.6
Signed-off-by: Mike Thompson <mpthompson@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.
For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.
For those which don't provide controllable transceivers
we will register nop transceivers.
Note that once OMAP's transceiver drivers reach mainline,
this glue layer will change accordingly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.
For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Spotted by Fengguang Wu:
|In file included from drivers/usb/gadget/ether.c:110:0:
|drivers/usb/gadget/u_ether.c:87:21: error: expected ')' before 'uint'
|drivers/usb/gadget/u_ether.c:88:25: error: expected ')' before string constant
This is because u_ether.c relied on having module.h included somewhere.
This isn't the case since composite.c is no longer included.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The bcdDevice field is defined as
|Device release number in binary-coded decimal
in the USB 2.0 specification. We use this field to distinguish the UDCs
from each other. In theory this could be used on the host side to apply
certain quirks if the "special" UDC in combination with this gadget is
used. This hasn't been done as far as I am aware. In practice it would
be better to fix the UDC driver before shipping since a later release
might not need this quirk anymore.
There are some driver in tree (on the host side) which use the bcdDevice
field to figure out special workarounds for a given firmware revision.
This seems to make sense. Therefore this patch converts all gadgets
(except a few) to use the kernel version instead a random 2 or 3 plus
the UDC number. The few that don't report kernel's version are:
- webcam
This one reports always a version 0x10 so allow it to do so in future.
- nokia
This one reports always 0x211. The comment says that this gadget works
only if the UDC supports altsettings so I added a check for this.
- serial
This one reports 0x2400 + UDC number. Since the gadget version is 2.4
this could make sense. Therefore bcdDevice is 0x2400 here.
I also remove various gadget_is_<name> macros which are unused. The
remaining few macros should be moved to feature / bug bitfield.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't fail the initialization check for the platform_data
if there is avaiable an associated device tree node.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
MODULE_VERSION and AUTHOR looks better in composite.c than in
usbstrings.c so I move it there.
I put David Brownell as the module Author as I belive he wrote most of
it.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This moves composite.c into libcomposite and updates all gadgets.
Finally!
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadgets provide custom entry here. Some may override it with an
etntry that is also created by composite if there was no value sumbitted
at all.
This patch removes all "custom manufacturer" strings which are the same
as these which are created by composite. Then it moves the creation of
the default manufacturer string to usb_composite_overwrite_options() in
case no command line argument has been used and the entry is still an
empty string.
By doing this we get rid of the global variable "composite_manufacturer"
in composite.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The struct usb_composite_driver members iProduct, iSerial and
iManufacturer can be entered directly via the string array. There is no
need for them to appear here.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch pushes the iProduct module argument from composite
into each gadget.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch pushes the iManufacturer module argument from composite into
each gadget. Once the user uses the module paramter, the string is
overwritten with the final value.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch pushes the iSerialNumber module argument from composite into
each gadget. Once the user uses the module paramter, the string is
overwritten with the final value.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The index in usb_string array is defined by the gadget. The gadget can
choose which index entry it assigns for the serial number and which the
product name. The gadget has just to ensure that the descriptor contains
the proper string id which is assigned by composite.
If the composite layer knows the index of the "default" information
which will be overwritten by module parameters, it can be used later to
overwrite it.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves the module options idVendor, idProduct and bcdDevice
from composite.c into each gadgets. This ensures compatibility with
current gadgets and removes the global variable which brings me step
closer towards composite.c in libcomposite
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After I moved the function from the header file to the c file I see:
| $ size drivers/usb/gadget/gadget_chips.o
| text data bss dec hex filename
| 1048 0 0 1048 418 drivers/usb/gadget/gadget_chips.o
That is almost a KiB which is removed from each user.
As Felipe pointed out, the function / usage is very dumb actually. This is
used for the following reasons:
- epautoconf ep hint (could provide a per-gadget callback)
- miss-features. currently the missing altsetting on pxa's and something
ZLP related on musbhdrc (looks like an optimisation which could be
implemented in musb itself if it is correct)
- unique BCD accross all UDCs. Not sure how important this is.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I have no idea what I've been thinking while I was doing this in the first
place. Now the strings are initialized properly and reported by lsusb.
Cc: stable@vger.kernel.org # v3.5
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This was broken in 2e87edf49 ("usb: gadget: make g_printer use
composite").
The USB-strings were not setup properly and were not used. No function
was added which results in an empty USB config.
While fixing this, the interface number is now auto generated and not
hard coded to 0.
Cc: stable@vger.kernel.org # v3.5
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using usb_string_ids_tab() instead multiple calls of usb_string_id()
seems to be handy. It also allows to add string without many checks.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a partly revert of 4fffd6e5 ("usb: gadget: composite: make
module parameters accessible at runtime").
It is not possible to change the VID or other property for a gadget
right now. This change has been made for Anrdoid gadget which has this
functionality in its copy of the file. This function is executed currently
only once and most caller in tree are __init.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
there is no read user of bufsiz, its content is available via
USB_COMP_EP0_BUFSIZ. Remove it.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves USB_BUFSIZ into global header file as
USB_COMP_EP0_BUFSIZ. There is currently only one user (f_sourcesink)
besides composite which need it. Ideally f_sourcesink would have its
own ep0 buffer. Lets keep it that way it was for now.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds epautoconf.c into libcomposite and updates all gadgets.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
epautoconf has two global variables which count the endpoint number of
last assigned endpoint.
This patch removes the global variable and keeps it as per (UDC) gadget.
While here, the ifdef is removed and now the in and outpoint are
enumerated unconditionally. The dwc3 for instance supports 32 endpoints
in total.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves config.c into libcomposite and updates all gadgets.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch aims to be simple. It removes #include usbstribgs.c line from each
gadget and creates libcomposite.ko which has only one member, that is
usbstribgs.c.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|drivers/usb/gadget/pxa25x_udc.h: In function 'dump_state':
|drivers/usb/gadget/pxa25x_udc.h:228:20: error: invalid type argument of '->' (have 'struct usb_ep')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the global variable composite in composite.c.
The private data which was saved there is now passed via an additional
argument to the bind() function in struct usb_gadget_driver.
Only the "old-style" UDC drivers have to be touched here, new style are
doing it right because this change is made in udc-core.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This Android gadget includes a bunch of .c files. Fixing normal gadgets
is not the real problem but this gadget is not always fixable since the
problem here are fundumential / design.
*I* wanted to get this removed but other people want to keep it even
though there were reports that Android itself is not using it. Some
poeple think that it is better to have this instead of nothing and other
argue that they need sdb and mass storage gadget. The sdb function is
not provided by ccg so I don't see the point of this. I don't see any
logical reasoning behind it and I decided that it is time for retreat.
This patch brings all dependencies of ccg into staging so I can do
whatever I want in drivers/usb/gadget without breaking ccg.
Cc: devel@driverdev.osuosl.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This partly reverts 07a18bd7 ("usb gadget: don't save bind callback in
struct usb_composite_driver") and fixes new drivers. The section missmatch
problems was solved by whitelisting bind callback in modpost.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This partly reverts 07a18bd7 ("usb gadget: don't save bind callback in
struct usb_composite_driver") and fixes new drivers. The section missmatch
problems was solved by whitelisting structs in question via __ref.
Cc: devel@driverdev.osuosl.org
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As it turns out, Sam's comment was better than I initially assumed. This
patch pushes as struct usb_composite_driver data structures into
__refdata section to avoid a section missmatch report from modpost
because the ->bind() can be marked __init. The only downside is that
modpost does not check between ->bind() and other member. However, it is
temporary.
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
avoids the following section missmatch
|WARNING: drivers/usb/gadget/g_audio.o(.init.text+0x2e7): Section
|mismatch in reference from the function afunc_bind() to the function
|.devexit.text:snd_uac2_remove()
|The function __init afunc_bind() references
|a function __devexit snd_uac2_remove().
|This is often seen when error handling in the init function
|uses functionality in the exit path.
|The fix is often to remove the __devexit annotation of
|snd_uac2_remove() so it may be used outside an exit section.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It was moved to be an argument in 07a18bd716 ("usb gadget: don't
save bind callback in struct usb_composite_driver"). The reason was to
avoid the section missmatch. The warning was shown because ->bind is
marked as __init becuase it is a one time init. The warning can be also
suppresed by whitelisting the variable i.e. rename it to lets say _probe.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first item on the todo list is a new user interface. Put this
information into Kconfig's help entry to people are not too confusing
once an user API changes which does not happen in kernel otherwise.
Cc: devel@driverdev.osuosl.org
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The various Orion SoCs, i.e. orion5x, kirkwood, dove, mv78xx0
and 370/XP have EHCI. Make sure USB_ARCH_HAS_EHCI reflects this.
Reported-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device tree support for twl4030 usb driver.
Update the Documentation with device tree binding information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add device tree support for twl6030 usb driver.
Update the Documentation with device tree binding information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All the PHY configuration other than VBUS, ID GND and OTG SRP are removed
from twl6030. The phy configurations are taken care by the dedicated
usb2 phy driver. So twl6030 is made as comparator driver for VBUS and
ID detection.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All phy related programming like enabling/disabling the clocks, powering
on/off the phy is taken care of by this driver. It is also used for OTG
related functionality like srp.
This also includes device tree support for usb2 phy driver and
the documentation with device tree binding information is updated.
Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "Low Performance USB Block driver" has been removed which a user of
libusual. Now we have only the usb-storage driver as the only driver in
tree. This makes libusual needless.
This patch removes libusal, fixes up all users. The usual-table is now
linked into usb-storage.
usb_usual.h remains in public include directory because some staging
users seem to need it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was scheduled to be removed in 3.6.
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory return by kzalloc() or kmem_cache_zalloc() has already
be set to zero, so remove useless memset(0).
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using list_move_tail() instead of list_del() + list_add_tail().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the call to PTR_ERR to access the value just tested by IS_ERR.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
(
if (IS_ERR(e)) { ... PTR_ERR(e) ... }
|
if (IS_ERR(e=e1)) { ... PTR_ERR(e) ... }
|
*if (IS_ERR(e))
{ ...
* PTR_ERR(e1)
... }
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the call to PTR_ERR to access the value just tested by IS_ERR.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
(
if (IS_ERR(e)) { ... PTR_ERR(e) ... }
|
if (IS_ERR(e=e1)) { ... PTR_ERR(e) ... }
|
*if (IS_ERR(e))
{ ...
* PTR_ERR(e1)
... }
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With "select USB_ISP1301 ...", it could happen that I2C isn't selected although
USB_ISP1301 depends on it. Fixing with "depends on ..." and emulating the
condition via "|| !()".
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
renesas_usbhs dma can transport 8byte alignment data, not 4byte.
This patch fixup it.
Reported-by: Sugnan Prabhu S <sugnan.prabhu@renesasmobile.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when missing USB PHY clock, kernel booting up will hang during USB
initialization. We should check USBGP[PHY_CLK_VALID] bit to avoid
CPU hanging in this case.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we will be removing items off the list using list_del() we need
to use a safer version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe(). We should use the safe macro if the loop
involves deletions of items.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When IORESOURCE_IRQ_SHAREABLE is set, the irq handler may be called
even if the interupt of the USB module doesn't happen. So, it may
clear the interrupt flags by mistake. This patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an unused statically defined array and an associated #define.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of this patch:
1. Moved existing tegra phy driver to drivers/USB directory.
2. Added standard USB phy driver APIs to tegra phy driver.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Driver for the "USB20D" / "USBD" block on BCM6328, BCM6368, BCM6816,
BCM6362, BCM3383, and others.
The hardware block was designed to support networking applications
(direct connection of a home router to a PC), and the endpoint
configuration is fixed.
[ balbi@ti.com : dropped USB_GADGET_DUALSPEED from Kconfig ]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_* functions are already used in this file. Hence
convert clk_get to devm_clk_get for completeness.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Richard Zhao