Commit Graph

5275 Commits

Author SHA1 Message Date
Marek Szyprowski fa34efff75 clk: samsung: Remove obsolete code for Exynos4412 ISP clocks
Exynos4412 ISP clock are provided by separate Exynos4412 ISP clock
driver, so support for them in Exynos4-clk driver can be removed.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:36:35 +02:00
Marek Szyprowski a766065279 clk: samsung: exynos5433: Add suspend state for TOP, CPIF & PERIC CMUs
Before entering system suspend, one has to ensure that some clocks from
TOP, CPIF and PERIC CMUs are enabled. This is needed by the firmware
to properly perform system suspend operation. Instead of adding more and
more clocks with CRITICAL flag, simply enable those clocks directly in
respective CMU registers using 'suspend_regs' feature.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:36:34 +02:00
Marek Szyprowski 70da9ee802 clk: samsung: Use NOIRQ stage for Exynos5433 clocks suspend/resume
SoC clock drivers should suspend after every other drivers in the system,
which are using clocks and resume before them. The last stage for calling
suspend device callbacks is NOIRQ stage and there exists driver, which use
that state (dwmmc-exynos), so Exynos5433 clocks driver should also use it.
During the same stage, clocks driver will be always suspended after its
clients as a direct result of proper device probe order (deferred probe
reorders the suspend call sequence).

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:36:33 +02:00
Marek Szyprowski 2d77f77c0a clk: samsung: exynos5420: Use generic helper for handling suspend/resume
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:36:32 +02:00
Marek Szyprowski 9a4d8a8c4d clk: samsung: exynos4: Use generic helper for handling suspend/resume
Replace common suspend/resume handling code by generic helper.
Handling of PLLs is a bit different in generic code, as they are handled
in the same way as other clock registers. Such approach was already used
on later Exynos SoCs and worked fine. Tests have shown that it works also
on Exynos4 SoCs and significantly simplifies the code.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:36:32 +02:00
Marek Szyprowski 8bf27eaa04 clk: samsung: Add support for setting registers state before suspend
Some registers of clock controller have to be set to certain values before
entering system suspend state. Till now drivers did that on their own,
but it will be easier to handle it by generic code and let drivers simply
to provide the list of registers and their state.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:36:31 +02:00
Marek Szyprowski c41b0ff2f6 clk: samsung: exynos5250: Use generic helper for handling suspend/resume
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:36:30 +02:00
Marek Szyprowski 3ac0b61578 clk: samsung: s5pv210: Use generic helper for handling suspend/resume
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:36:29 +02:00
Marek Szyprowski 3773ee423e clk: samsung: s3c64xx: Use generic helper for handling suspend/resume
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.

[snawrocki@kernel.org: Whitespace correction]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-10-05 13:35:37 +02:00
Russ Dill d6e7bbc148 clk: ti: Add functions to save/restore clk context
SoCs like AM43XX lose clock registers context during RTC-only
suspend. Hence add functions to save/restore the clock registers
context.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
2018-10-03 15:29:19 +03:00
Keerthy 435365485f clk: clk: Add clk_gate_restore_context function
The clock gate restore context function enables or disables
the gate clocks based on the enable_count. This is done in cases
where the clock context is lost and based on the enable_count
the clock either needs to be enabled/disabled.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
2018-10-03 15:29:15 +03:00
Russ Dill 8b95d1ce33 clk: Add functions to save/restore clock context en-masse
Deep enough power saving mode can result into losing context of the clock
registers also, and they need to be restored once coming back from the power
saving mode. Hence add functions to save/restore clock context.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
2018-10-03 15:29:04 +03:00
Tero Kristo dffa9051d5 clk: ti: dra7: add new clkctrl data
The new clkctrl data layout for dra7xx is split based on clockdomain
boundaries. Previously the split was based on CM boundaries. This patch
adds the new data as separate data entity, retaining the compatibility
data also for now. The compatibility data can be removed once no longer
needed.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
2018-10-03 15:02:27 +03:00
Tero Kristo 43c56e046c clk: ti: dra7xx: rename existing clkctrl data as compat data
Rename the existing clkctrl data in preparation of upcoming clkdm
based split for it. Once the DT data has transitioned also, the
compat data can be removed.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
2018-10-03 15:02:27 +03:00
Tero Kristo 76a1049b84 clk: ti: am43xx: add new clkctrl data for am43xx
The new clkctrl data layout for am43xx is split based on clockdomain
boundaries. Previously the split was based on CM boundaries. This patch
adds the new data as separate data entity, retaining the compatibility
data also for now. The compatibility data can be removed once no longer
needed.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
2018-10-03 15:02:27 +03:00
Tero Kristo 131ee08f3f clk: ti: am43xx: rename existing clkctrl data as compat data
Rename the existing clkctrl data in preparation of upcoming clkdm
based split for it. Once the DT data has transitioned also, the
compat data can be removed.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
2018-10-03 15:02:26 +03:00
Tero Kristo 296e583e99 clk: ti: am33xx: add new clkctrl data for am33xx
The new clkctrl data layout for am33xx is split based on clockdomain
boundaries. Previously the split was based on CM boundaries. This patch
adds the new data as separate data entity, retaining the compatibility
data also for now. The compatibility data can be removed once no longer
needed.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
2018-10-03 15:02:26 +03:00
Tero Kristo e97017f935 clk: ti: am33xx: rename existing clkctrl data as compat data
Rename the existing clkctrl data in preparation of upcoming clkdm
based split for it. Once the DT data has transitioned also, the
compat data can be removed.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
2018-10-03 15:02:26 +03:00
Tero Kristo 1dc88f78da clk: ti: clkctrl: replace dashes from clkdm name with underscore
The change in the DTS data node naming prevents using underscore
within the node names and force usage of dash instead. On the other
hand, clockdomains use underscore instead of dash, so this must be
replaced within the driver code so that the mapping between the two
can be done properly.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
2018-10-03 15:02:26 +03:00
Tero Kristo 47b00dcf14 clk: ti: clkctrl: support multiple clkctrl nodes under a cm node
Currently, only one clkctrl node can be added under a specific CM node
due to limitation with the implementation. Modify the code to pick-up
clockdomain name from the clkctrl node instead of CM node if provided.
Also, add a new flag to the TI clock driver so that both modes can
be supported simultaneously.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
2018-10-03 15:02:26 +03:00
Nishanth Menon 2f149e6e14 clk: keystone: Enable TISCI clocks if K3_ARCH
K3_ARCH uses TISCI for clocks as well. Enable the same
for the driver support.

Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-10-02 12:55:15 -07:00
Bartosz Golaszewski e3aaadb0f0 clk: davinci: kill davinci_clk_reset_assert/deassert()
This code is no longer used. Remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-10-02 08:54:14 -07:00
Stephen Boyd 02621216e1 Allwinner clk fixes for 4.19
One fix for the Audio PLL that were not properly set and generating noise
 on the A10 SoCs.
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEE0VqZU19dR2zEVaqr0rTAlCFNr3QFAluvlEwACgkQ0rTAlCFN
 r3RWOg/9Fw0fD9LZ15A9KIbLfH2k2JWALPct6jEOHCQIj1td+aepWngwG5m4dEp5
 Rd+R38pjGLpO8VJ36TuS0majvUFlRtJIsGOZ+CRTj+QY0XceFldmAc/QgBCNb5wi
 uVXxH/Xqtv+DAf1FZWPKMOmwdjbDtqmnrpfKs1LPZvy9Y7z/PGZZVk13N+OrXrHx
 CXu1zIJ8J2Io5C0r/tVPosXJRDy04lzUZ2+XH1dev/h3/MZ9eiViKF8YCY2k+Frp
 mkKPjT2v0Ew0lnD64sw55khKcEuajaKxeqzAlSOwjQ+Kunr8/hr6KdauZmEoxMUZ
 G+Twkge8nVxdzJUOIrA0psFFaPj3bLpc97613Lwg8oQBeVz46fPMvHlMNJ3Flz18
 H9TRzzVT6eG1Ck7LAB2o30NB/Fate3PaOwTWHe3nnFgdqbWwdy18aBJVKK2qeqwd
 alU/IFKT5fenIpRiQyJOH4djVLRkATGDGkOP9KQ9gtpDA+FMw37hnQkKS20C5U0E
 1X/+hFLtyjw2EvTsoV/MvVLpMxZkCIvIQuO8yC4Cba93g4R1XSmdhrkN45OaYf+n
 v8QYVzMrQSY0DANVnoGQ0y+e+fl49mhNhosMWZzMZaWuI5tutV1oVsYqObJ2eUpk
 yux9DhwtXrw3h2L1o3m2SYes/AL5Xppu00HXBx7f15xhR7VKC3o=
 =q4se
 -----END PGP SIGNATURE-----

Merge tag 'sunxi-clk-fixes-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes

Pull Allwinner clk fixes for 4.19 from Maxime Ripard:

One fix for the Audio PLL that were not properly set and generating noise
on the A10 SoCs.

* tag 'sunxi-clk-fixes-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  clk: sunxi-ng: sun4i: Set VCO and PLL bias current to lowest setting
2018-10-01 15:22:25 -07:00
Gregory CLEMENT 6ffeddd6bc clk: mvebu: ap806: Remove superfluous of_clk_add_provider
While applying the commit a8309cedcd ("clk: apn806: Add eMMC clock to
system controller driver"), of_clk_add_provider was added wheres it was
already present in the probe function.

This extraneous call is harmless but not useful so remove it.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-10-01 15:13:42 -07:00
Gregory CLEMENT c3828949a2 clk: mvebu: use SPDX-License-Identifier
Convert the remaining files to SPDX license description.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-10-01 15:12:47 -07:00
Kuninori Morimoto 9e288cefcc clk: renesas: Convert to SPDX identifiers
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[rebased against clk-spdx]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-09-28 17:16:37 -07:00
Rob Herring 76ec23b127 clk: mvebu: use for_each_of_cpu_node iterator
Use the for_each_of_cpu_node iterator to iterate over cpu nodes. This
has the side effect of defaulting to iterating using "cpu" node names in
preference to the deprecated (for FDT) device_type == "cpu".

Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
2018-09-28 14:25:58 -05:00
Chris Brandt a53a28dca4 clk: renesas: r7s9210: Add SPI clocks
Add RSPI clocks for RZ/A2.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-28 09:57:09 +02:00
Chris Brandt 4cb1480f5f clk: renesas: r7s9210: Move table update to separate function
Same functionality, just easier to read.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-26 14:22:05 +02:00
Chris Brandt b9553c13b1 clk: renesas: r7s9210: Convert some clocks to early
The OSTM timer driver for RZ/A2 uses TIMER_OF_DECLARE which requires the
ostm module clocks to be registers early in boot.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-26 14:22:05 +02:00
Chris Brandt 1f7db7bbf0 clk: renesas: cpg-mssr: Add early clock support
Add support for SoCs that need to register core and module clocks early in
order to use OF drivers that exclusively use macros such as
TIMER_OF_DECLARE.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-26 14:22:00 +02:00
Martin Blumenstingl 93c873d686 clk: meson: meson8b: use the regmap in the internal reset controller
For now the reset controller was using raw register access because the
early init did not initialize the regmap. However, now that clocks are
initialized early we can simply use the regmap also for the reset
controller.
No functional changes.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-09-26 12:02:00 +02:00
Martin Blumenstingl 6291b8c5ac clk: meson: meson8b: register the clock controller early
Until now only the reset controller (part of the clock controller
register space) was registered early in the boot process, while the
clock controller itself was registered later on.
However, some parts of the SoC are initialized early in the boot process,
such as the SRAM and the TWD timer. The bootloader already enables these
clocks so we didn't see any issues so far.

Register the clock controller early so other drivers (such as the SRAM
and TWD timer) can use the clocks early in the boot process.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-09-26 12:02:00 +02:00
Yixun Lan 69b93104c7 clk: meson-axg: pcie: drop the mpll3 clock parent
We found the PCIe driver doesn't really work with
the mpll3 clock which is actually reserved for debug,
So drop it from the mux list.

Fixes: 33b89db68236 ("clk: meson-axg: add clocks required by pcie driver")
Tested-by: Jianxin Qin <jianxin.qin@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-09-26 12:02:00 +02:00
Jerome Brunet 56dbabc0ff clk: meson: axg: round audio system master clocks down
Some of the master clocks provided by the axg audio clock controller are
system clock (spdifin and pdm sysclk). They are used to clock an internal
DSP of the related devices. Having them constantly rounded down instead
of closest is preferable.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-09-26 12:02:00 +02:00
Jerome Brunet dd601dbc01 clk: meson: clk-pll: drop hard-coded rates from pll tables
Putting hard-coded rates inside the parameter tables assumes that
the parent is known and will never change. That's a big assumption
we should not make.

We have everything we need to recalculate the output rate using
the parent rate and the rest of the parameters. Let's do so and
drop the rates from the tables.

Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-09-26 12:02:00 +02:00
Jerome Brunet 87173557d2 clk: meson: clk-pll: remove od parameters
Remove od parameters from pll clocks and add post dividers clocks
instead. Some clock, especially the one which feature several ods,
may provide output between those ods. Also, some drivers, such
as the hdmi driver, may require a more detailed control of the
clock dividers, compared to what CCF would perform automatically.

One added benefit of removing ods is that it also greatly reduce the
size of the rate parameter tables.

In the future, we could possibly take the predivider 'n' out of this
driver as well. To do so, we will need to understand the constraints
for the PLL to lock and whether or not it depends on the input clock
rate.

Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-09-26 12:01:57 +02:00
Jerome Brunet 2303a9ca69 clk: meson: clk-pll: drop CLK_GET_RATE_NOCACHE where unnecessary
CLK_GET_RATE_NOCACHE should only be necessary when the registers
controlling the rate of clock may change outside of CCF. On Amlogic,
it should only be the case for the hdmi pll which is directly controlled
by the display driver (WIP to fix this).

The other plls should not require this flag.

Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-09-26 12:00:28 +02:00
Jerome Brunet e40c7e3cda clk: meson: clk-pll: add enable bit
Add the enable the bit of the pll clocks.
These pll clocks may be disabled but we can't model this as an external
gate since the pll needs to lock when enabled.

Adding this bit allows to drop the poke of the first register of PLL.
This will be useful to model the different components of the pll using
generic clocks elements

Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-09-26 12:00:28 +02:00
Sergei Shtylyov 9ef5e0370d clk: renesas: r8a77970: Add TPU clock
The TPU0 clock wasn't present in the original R8A77970 patch by Daisuke
Matsushita, it was added in a later BSP version...

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-25 08:56:09 +02:00
Geert Uytterhoeven 5915838b7a clk: renesas: r8a77990: Fix incorrect PLL0 divider in comment
PLL0 runs at 4.8 GHz, i.e. EXTAL x 100.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-25 08:55:56 +02:00
Fabrizio Castro 906e0a4a6d clk: renesas: cpg-mssr: Add r8a774c0 support
Add RZ/G2E (R8A774C0) Clock Pulse Generator / Module Standby and
Software Reset support.

Based on Table 8.2g of "RZ/G Series, 2nd Generation User's Manual:
Hardware (Rev. 0.61, June 12, 2018)".

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-19 16:42:14 +02:00
Biju Das 016f966315 clk: renesas: r8a7743: Add r8a7744 support
Add RZ/G1N (R8A7744) Clock Pulse Generator / Module Standby and Software
Reset support.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-19 16:39:45 +02:00
Hans de Goede 648e921888 clk: x86: Stop marking clocks as CLK_IS_CRITICAL
Commit d31fd43c0f ("clk: x86: Do not gate clocks enabled by the
firmware"), which added the code to mark clocks as CLK_IS_CRITICAL, causes
all unclaimed PMC clocks on Cherry Trail devices to be on all the time,
resulting on the device not being able to reach S0i3 when suspended.

The reason for this commit is that on some Bay Trail / Cherry Trail devices
the r8169 ethernet controller uses pmc_plt_clk_4. Now that the clk-pmc-atom
driver exports an "ether_clk" alias for pmc_plt_clk_4 and the r8169 driver
has been modified to get and enable this clock (if present) the marking of
the clocks as CLK_IS_CRITICAL is no longer necessary.

This commit removes the CLK_IS_CRITICAL marking, fixing Cherry Trail
devices not being able to reach S0i3 greatly decreasing their battery
drain when suspended.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17 18:47:58 -07:00
Hans de Goede b1e3454d39 clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
Commit d31fd43c0f ("clk: x86: Do not gate clocks enabled by the
firmware") causes all unclaimed PMC clocks on Cherry Trail devices to be on
all the time, resulting on the device not being able to reach S0i2 or S0i3
when suspended.

The reason for this commit is that on some Bay Trail / Cherry Trail devices
the ethernet controller uses pmc_plt_clk_4. This commit adds an "ether_clk"
alias, so that the relevant ethernet drivers can try to (optionally) use
this, without needing X86 specific code / hacks, thus fixing ethernet on
these devices without breaking S0i3 support.

This commit uses clkdev_hw_create() to create the alias, mirroring the code
for the already existing "mclk" alias for pmc_plt_clk_3.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17 18:47:58 -07:00
Chris Brandt fde35c9c7d clk: renesas: cpg-mssr: Add R7S9210 support
Add support for the R7S9210 (RZ/A2) Clock Pulse Generator and Module
Standby.

The Module Standby HW in the RZ/A series is very close to R-Car HW, except
for how the registers are laid out.
The MSTP registers are only 8-bits wide, there are no status registers
(MSTPSR), and the register offsets are a little different. Since the RZ/A
hardware manuals refer to these registers as the Standby Control Registers,
we'll use that name to distinguish the RZ/A type from the R-Car type.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Rob Herring <robh@kernel.org> # DT bits
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-11 12:01:07 +02:00
Sergei Shtylyov 6207ba0434 clk: renesas: r8a77970: Add TMU clocks
The TMU clocks weren't present in the original R8A77970 patch by Daisuke
Matsushita, they were added in a later BSP version...

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-11 11:58:52 +02:00
Sergei Shtylyov 5986b503da clk: renesas: r8a77970: Add CMT clocks
Add the R8A77970 CMT module clocks.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-11 11:58:02 +02:00
Phil Edworthy ee02950d53 clk: renesas: r9a06g032: Fix UART34567 clock rate
The clock for UARTs 0 through 2 is UART012, the clock for UARTs 3 through
7 is UART34567.
For UART012, we stop the clock driver from changing the clock rate. This
is because the Synopsys UART driver simply sets the reference clock to 16x
the baud rate, but doesn't check if the actual rate is within the required
tolerance. The RZ/N1 clock divider can't provide this (we have to rely on
the UART's internal divider to set the correct clock rate), so you end up
with a clock rate that is way off what you wanted.

In addition, since the clock is shared between multiple UARTs, you don't
want the driver trying to change the clock rate as it may affect the other
UARTs (which may not have been configured yet, so you don't know what baud
rate they will use). Normally, the clock rate is set early on before Linux
to some very high rate that supports all of the clock rates you want.

This change stops the UART34567 clock rate from changing for the same
reasons.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-11 11:57:25 +02:00
Chen-Yu Tsai 80a6ec7d5e
clk: sunxi-ng: sun4i: Set VCO and PLL bias current to lowest setting
The default mid-level PLL bias current setting interferes with sigma
delta modulation. This manifests as decreased audio quality at lower
sampling rates, which sounds like radio broadcast quality, and
distortion noises at sampling rates at 48 kHz or above.

Changing the bias current settings to the lowest gets rid of the
noise.

Fixes: de34485191 ("clk: sunxi-ng: sun4i: Use sigma-delta modulation
		      for audio PLL")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-09-07 10:20:50 +02:00
Marek Szyprowski b5331e2fea clk: samsung: s3c2443: Use generic helper for handling suspend/resume
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-09-06 20:47:08 +02:00
Marek Szyprowski 1b3493d755 clk: samsung: s3c2412: Use generic helper for handling suspend/resume
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-09-06 20:47:01 +02:00
Marek Szyprowski 6bdac3b4c4 clk: samsung: s3c2410: Use generic helper for handling suspend/resume
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-09-06 20:46:47 +02:00
Marek Szyprowski 53e6ab3d07 clk: samsung: Remove excessive include
Exynos Audio SubSystem and Exynos3250 clock drivers don't use any syscore
function, so don't include linux/syscore_ops.h in their code.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-09-06 20:45:44 +02:00
Jagan Teki 8b2a378704
dt-bindings: clock: sun50i-a64-ccu: Add PLL_VIDEO0 macro
Allwinner A64 HDMI PHY clock has PLL_VIDEO0 as a parent.

Include the macro on dt-bindings so-that the same can be used
while defining CCU clock phandles.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-09-05 09:19:59 +02:00
Icenowy Zheng 5de39acaf3
clk: sunxi-ng: a64: Add max. rate constraint to video PLLs
Video PLLs on A64 can be set to higher rate that it is actually
supported by HW.

Limit maximum rate to 1008 MHz. This is the maximum allowed rate by BSP
clock driver. Interestengly, user manual specifies maximum frequency to
be 600 MHz. Historically, this data was wrong in some user manuals for
other SoCs, so more faith is put in BSP clock driver.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-09-05 09:16:10 +02:00
Jagan Teki 65b1e8a6ca
clk: sunxi-ng: a64: Add minimal rate for video PLLs
According to documentation and experience with other similar SoCs, video
PLLs don't work stable if their output frequency is set below 192 MHz.

Because of that, set minimal rate to both A64 video PLLs to 192 MHz.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-09-05 09:15:26 +02:00
Icenowy Zheng c2ff8383cc
clk: sunxi-ng: sun50i: h6: Add 2x fixed post-divider to MMC module clocks
On the H6, the MMC module clocks are fixed in the new timing mode,
i.e. they do not have a bit to select the mode. These clocks have
a 2x divider somewhere between the clock and the MMC module.

To be consistent with other SoCs supporting the new timing mode,
we model the 2x divider as a fixed post-divider on the MMC module
clocks.

This patch adds the post-dividers to the MMC clocks, following the
approach on A64.

Fixes: 524353ea48 ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-09-05 08:59:57 +02:00
Sergei Shtylyov 381081ffc2 clk: renesas: r8a77970: Add SD0H/SD0 clocks for SDHI
On R-Car V3M (AKA R8A77970), the SD0CKCR is laid out differently than on
the other R-Car gen3 SoCs. In fact, the layout is the same as on R-Car gen2
SoCs, so we'll need to copy the divisor tables from the R-Car gen2 driver.
We'll also need to support the SoC specific clock types, thus we're adding
CLK_TYPE_GEN3_SOC_BASE at the end of 'enum rcar_gen3_clk_types', declare
SD0H/SDH clocks in 'enum r8a77970_clk_types', and handle those clocks in
the overridden cpg_clk_register() method; then, finally, add the SD-IF
module clock (derived from the SD0 clock).

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-03 09:58:33 +02:00
Sergei Shtylyov 0a87bf6cd5 clk: renesas: r8a77980: Add CMT clocks
Now that RCLK has been added by Geert, we can add the CMT module clocks.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-09-03 09:58:33 +02:00
Miquel Raynal 5beb1e60db clk: mvebu: armada-37xx-periph: add suspend/resume support
Add suspend/resume hooks in Armada 37xx peripheral clocks driver to
handle S2RAM operations.

One can think that these hooks are useless by comparing the register
values before and after a suspend/resume cycle: they will look the same
anyway. This is because of some scripts executed by the Cortex-M3 core
during ATF operations to init both the clocks and the DDR. These values
could be modified by the BL33 stage or by Linux itself and should be
preserved.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-31 10:47:48 -07:00
Miquel Raynal d9d95e78cf clk: mvebu: armada-37xx-periph: save the IP base address in the driver data
Prepare the introduction of suspend/resume hooks by having an easy way
to access all the registers in one go just from a device: add the IP
base address in the driver data.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-31 10:47:48 -07:00
Gustavo A. R. Silva e9a2310fb6 reset: hisilicon: fix potential NULL pointer dereference
There is a potential execution path in which function
platform_get_resource() returns NULL. If this happens,
we will end up having a NULL pointer dereference.

Fix this by replacing devm_ioremap with devm_ioremap_resource,
which has the NULL check and the memory region request.

This code was detected with the help of Coccinelle.

Cc: stable@vger.kernel.org
Fixes: 97b7129cd2 ("reset: hisilicon: change the definition of hisi_reset_init")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-31 10:37:00 -07:00
Geert Uytterhoeven b30c862f2a clk: renesas: r8a77990: Add missing I2C7 clock
When trying to use I2C7 on R-Car E3:

    renesas-cpg-mssr e6150000.clock-controller: Cannot get module clock 1003: -2
    i2c-rcar e6690000.i2c: failed to add to PM domain always-on: -2
    i2c-rcar: probe of e6690000.i2c failed with error -2

Unlike other R-Car Gen3 SoCs, R-Car E3 has more than 7 I2C bus
interfaces.  Add the forgotten module clock for the 8th instance to fix
this.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
2018-08-31 10:33:59 +02:00
Urja Rannikko c14d28e86d clk: rockchip: improve rk3288 pll rates for better hdmi output
Add and correct PLL rates for better hdmi output.

This includes minimizing jitter on 213 MHz for better 71 MHz,
250.5 MHz for better 83.5 MHz, 428 MHz for better 25.175 Mhz,
low jitter 273 MHz for better 68.25 mhz, 356 MHz for better 118.68 Mhz
and 300MHz.

Increase the used Fvco for 308, 324 MHz, 292.5 MHz, 273.6 MHz,
238 MHz and 216 MHz.

And add some additional rates allowing to reach better hdmi-related
rates in general.

These match the rates used by ChromeOS, so have been quite widely tested.

Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2018-08-31 09:43:35 +02:00
Colin Ian King 1adb0a9faa clk: mediatek: remove unused array audio_parents
Array audio_parents is declared but never used, hence it is redundant
and can be removed.

Cleans up clang warning:
warning: 'audio_parents' defined but not used [-Wunused-const-variable=]

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 18:29:36 -07:00
Amit Nischal 78412c2620 clk: qcom: Add camera clock controller driver for SDM845
Add support for the camera clock controller found on SDM845
based devices. This would allow camera drivers to probe and
control their clocks.

Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 18:27:06 -07:00
Wolfram Sang e848c2ea11 clk: renesas: use SPDX identifier for Renesas drivers
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 18:18:44 -07:00
Alexey Khoroshilov 0b85de7cef clk: cdce925: release child device nodes
of_get_child_by_name() returns device node with refcount incremented,
but there is no decrement in cdce925_probe(). The patch adds one.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 15:19:16 -07:00
Gustavo A. R. Silva 681cd4a890 clk: qcom: clk-branch: Use true and false for boolean values
Return statements in functions returning bool should use true or false
instead of an integer value.

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 15:18:59 -07:00
Douglas Anderson 2bdb2a1cca clk: qcom: Allocate space for NULL terimation in DFS table
The table allocated in clk_rcg2_dfs_populate_freq_table() is
eventually iterated over by qcom_find_freq() which assumes that the
table is NULL terminated.  Allocate one extra space in the array for
the NULL termination.  Initting of the NULL termination is implicit
due to kcalloc().

Fixes: cc4f6944d0 ("clk: qcom: Add support for RCG to register for DFS")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 14:59:39 -07:00
Akshu Agrawal bded6c03e3 clk: x86: Set default parent to 48Mhz
System clk provided in ST soc can be set to:
48Mhz, non-spread
25Mhz, spread
To get accurate rate, we need it to set it at non-spread
option which is 48Mhz.

Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Fixes: 421bf6a1f0 ("clk: x86: Add ST oscout platform clock")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 14:47:41 -07:00
Johan Hovold 00a461cc32 clk: ti: fix OF child-node lookup
Fix child-node lookup which by using the wrong OF helper was searching
the whole tree depth-first, something which could end up matching an
unrelated node.

Also fix the related node-reference leaks.

Fixes: 5b385a45e0 ("clk: ti: add support for clkctrl aliases")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 14:44:01 -07:00
Rob Herring e665f029a2 clk: Convert to using %pOFn instead of device_node.name
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-30 09:50:20 -07:00
Douglas Anderson 4f83d9b848 clk: qcom: Add qspi (Quad SPI) clocks for sdm845
Add both the interface and core clock.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-28 15:56:38 -07:00
Rajendra Nayak b567752144 clk: qcom: Add some missing gcc clks for msm8996
Add a few missing gcc clks for msm8996

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: omit aggre0_noc_qosgen_extref_clk]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-28 15:51:44 -07:00
Gustavo A. R. Silva 450b6b9b16 clk: npcm7xx: fix memory allocation
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
	int stuff;
        void *entry[];
};

instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count,
GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, currently, there is a bug during the allocation:

sizeof(npcm7xx_clk_data) should be sizeof(*npcm7xx_clk_data)

Fix this bug by using struct_size() in kzalloc()

This issue was detected with the help of Coccinelle.

Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Avi Fishman <avifishman70@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-28 15:12:59 -07:00
Hoan Nguyen An bc7133cef8 clk: renesas: r8a77965: Add FDP clock
This patch adds FDP1-0 clock to the R8A77965 SoC.

Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-28 11:06:11 +02:00
Krzysztof Kozlowski 8748b4a786 clk: s2mps11: Use existing defines from bindings for clock IDs
The clock IDs must match between DeviceTree bindings and the driver.
There is already a header file used by DeviceTree sources so include it
in the driver to remove duplicated symbols.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-27 14:18:36 -07:00
Krzysztof Kozlowski 94047d9795 clk: s2mps11,s3c64xx: Add SPDX license identifiers
Replace GPL v2.0 and v2.0+ license statements with SPDX license
identifiers.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-27 14:17:03 -07:00
Krzysztof Kozlowski f300168a3a clk: max77686: Add SPDX license identifiers
Replace GPL v2.0 and v2.0+ license statements with SPDX license
identifiers.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-27 14:16:51 -07:00
Taniya Das 8b69c6dba2 clk: qcom: gcc: Register QUPv3 RCGs for DFS on SDM845
QUPv3 clocks support DFS and thus register the RCGs which require support
for the same.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Use new macro, split out init structures so they
don't have to be copied]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-27 13:39:50 -07:00
Taniya Das cc4f6944d0 clk: qcom: Add support for RCG to register for DFS
Dynamic Frequency switch is a feature of clock controller by which request
from peripherals allows automatic switching frequency of input clock
without SW intervention. There are various performance levels associated
with a root clock. When the input performance state changes, the source
clocks and division ratios of the new performance state are loaded on to
RCG via HW and the RCG switches to new clock frequency when the RCG is in
DFS HW enabled mode.

Register the root clock generators(RCG) to switch to use the dfs clock ops
in the cases where DFS is enabled. The clk_round_rate() called by the clock
consumer would invoke the dfs determine clock ops and would read the DFS
performance level registers to identify all the frequencies supported and
update the frequency table. The DFS clock consumers would maintain these
frequency mapping and request the desired performance levels.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Rework registration logic to stop copying, change
recalc_rate() to index directly into the table if possible and fallback
to calculating on the fly with an assumed correct parent]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-27 13:36:25 -07:00
Biju Das 331a53e05b clk: renesas: cpg-mssr: Add r8a774a1 support
Add RZ/G2M (R8A774A1) Clock Pulse Generator / Module Standby and Software
Reset support.

Based on the Table 8.2b of "RZ/G Series, 2nd Generation User's Manual:
Hardware ((Rev. 0.61, June 12, 2018)".

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-27 17:00:19 +02:00
Takeshi Kihara e59bb7be47 clk: renesas: r8a77965: Add SATA clock
This patch adds SATA clock to the R8A77965 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: rebased to upstream base]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-27 17:00:19 +02:00
Geert Uytterhoeven f3824deb46 clk: renesas: r8a77980: Add RCLK for watchdog timer
On R-Car V3H, RCLK can be switched between EXTALR and the On-Chip
Oscillator using mode pin MD19.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:19 +02:00
Geert Uytterhoeven cd51e427e0 clk: renesas: rcar-gen3: Add support for mode pin clock selection
Make the existing support for selecting between clean and SSCG clocks
using MD12 more generic, to allow using other mode pins for arbitrary
clock selection.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven 4f57998d64 clk: renesas: r8a77995: Correct RCLK handling
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car D3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.

Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven dc643a843b clk: renesas: r8a77990: Correct RCLK handling
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car E3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.

Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven b9d0b84b3d clk: renesas: rcar-gen3: Add support for RCKSEL clock selection
Add a clock type and macro for defining clocks where the parent and
divider are selected based on the value of the RCKCR.CKSEL bit.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven 0d2602d750 clk: renesas: cpg-mssr: Add support for fixed rate clocks
Add support for defining fixed rate clocks, to be used for on-chip
oscillators.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven 3a251270e6 clk: renesas: r8a77980: Add OSC predivider configuration and clock
R-Car Gen3 Hardware Manual Rev.0.54 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC clock.  Hence augment the configuration structure with all
documented predivider values.

Add the OSC clock using the configured predivider.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven 979a2298a5 clk: renesas: r8a77965: Add OSC EXTAL predivider configuration
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks.  Hence augment the configuration structure
with all documented predivider values.

According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car M3-N does not
have the CPG_RCKCR register.  Change the OSC and RINT clock definitions
to use the OSC EXTAL predivider instead, which is supported on all R-Car
M3-N SoC revisions.

Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven 7b8b9a4131 clk: renesas: r8a7796: Add OSC EXTAL predivider configuration
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks.  Hence augment the configuration structure
with all documented predivider values.

According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car M3-W ES1.1.  Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car M3-W SoC revisions.

Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven f23b866e20 clk: renesas: r8a7795: Add OSC EXTAL predivider configuration
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks.  Hence augment the configuration structure
with all documented predivider values.

According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car H3 ES2.0.  Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car H3 SoC revisions.

Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven 38c79e2899 clk: renesas: rcar-gen3: Add support for OSC EXTAL predivider
Add a clock type and macro for defining clocks using the OSC EXTAL
predivider combined with a fixed divider.

On most R-Car Gen3 SoCs, the predivider value depends on mode pins, and
thus must be specified in the configuration structure.

Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Geert Uytterhoeven fdb78a8c35 clk: renesas: rcar-gen3: Rename rint to .r
All other internal clock names have a period prepended.

Hence rename the internal RCLK from "rint" to ".r", and move it to the
section where all other internal clocks are defined.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-08-27 17:00:18 +02:00
Jernej Skrabec a528872dbb
clk: sunxi-ng: a83t: Add max. rate constraint to video PLLs
It may happen that clock framework finds optimal video PLL rate above
that which is really supported by HW.

User manual doesn't really say what is upper limit for video PLLs on
A83T. Because of that, use the maximum rate defined in BSP clk driver
which is 3 GHz.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-08-27 09:18:11 +02:00
Jernej Skrabec a8e5433cdc
clk: sunxi-ng: nkmp: Add constraint for maximum rate
Some, if not most, NKMP PLLs can be set to higher rate that is really
supported by HW.

Implement support for maximum frequency constrain for NKMP PLLs.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-08-27 09:18:10 +02:00
Jernej Skrabec b16fb66915
clk: sunxi-ng: r40: Add max. rate constraint to video PLLs
Video PLLs on R40 can be set to higher rate that it is actually
supported by HW.

Limit maximum rate to 1008 MHz. This is the maximum allowed rate by BSP
clock driver. Interestengly, user manual specifies maximum frequency to
be 600 MHz. Historically, this data was wrong in some user manuals for
other SoCs, so more faith is put in BSP clock driver.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-08-27 09:18:09 +02:00
Jernej Skrabec 02d7901695
clk: sunxi-ng: h3/h5: Add max. rate constraint to pll-video
As it turns out, pll-video can be set to higher rate that it is really
supported by HW.

For example, one monitor requested 185.58 MHz pixel clock. Clock
framework calculated that minimum rate error would be when pll-video
is set to 2040 MHz. This is clearly out of specs.

Both H3 and H5 user manuals specify 600 MHz as maximum supported rate.
However, BSP clock drivers allow up to 912 MHz and 1008 MHz
respectively. Here 912 MHz is chosen because user manuals were already
proven wrong once for lower limits.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-08-27 09:18:08 +02:00
Jernej Skrabec cb54fbd21a
clk: sunxi-ng: Add maximum rate constraint to NM PLLs
On some NM PLLs, frequency can be set above PLL working range.

Add a constraint for maximum supported rate. This way, drivers can
specify which is maximum allowed rate for PLL.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-08-27 09:18:01 +02:00
Rongyi Chen 58c0f79887 clk: sunxi-ng: h6: fix PWM gate/reset offset
Currently the register offset of the PWM bus gate in Allwinner H6 clock
driver is wrong.

Fix this issue.

Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Rongyi Chen <chenyi@tt-cool.com>
[Icenowy: refactor commit message]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2018-08-27 10:35:04 +08:00
Icenowy Zheng 2852bfbf4f clk: sunxi-ng: h6: fix bus clocks' divider position
The bus clocks (AHB/APB) on Allwinner H6 have their second divider start
at bit 8, according to the user manual and the BSP code. However,
currently the divider offset is incorrectly set to 16, thus the divider
is not correctly read and the clock frequency is not correctly calculated.

Fix this bit offset on all affected bus clocks in ccu-sun50i-h6.

Cc: stable@vger.kernel.org # v4.17.y
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2018-08-27 10:35:03 +08:00
Linus Torvalds f3ea496213 ARM: SoC driver updates
Some of the larger changes this merge window:
  - Removal of drivers for Exynos5440, a Samsung SoC that never saw
    widespread use.
  - Uniphier support for USB3 and SPI reset handling
  - Syste control and SRAM drivers and bindings for Allwinner platforms
  - Qualcomm AOSS (Always-on subsystem) reset controller drivers
  - Raspberry Pi hwmon driver for voltage
  - Mediatek pwrap (pmic) support for MT6797 SoC
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlt+MMkPHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3pB4QAIj7iVxSKEQFz65iXLTfMJKFZ9TSvRgWSDyE
 CHF+WOQGTnxkvySEHSw/SNqDM+Bas8ijR8b4vWzsXJFB+3HA0ZTGLU379/af1zCE
 9k8QjyIWtRWKX9fo7qCHVXlMfxGbOdbCOsh4jnmHqEIDxCHXpIiJRfvUbKIXGpfn
 tw6QpM70vm6Q6AdKwzmDbMCYnQAMWxBK/G/Q7BfRG+IYWYjFGbiWIc9BV9Ki8+nE
 3235ISaTHvAHodoec8tpLxv34GsOP4RCqscGYEuCf22RYfWva4S9e4yoWT8qPoIl
 IHWNsE3YWjksqpt9rj9Pie/PycthO4E4BUPMtqjMbC2OyKFgVsAcHrmToSdd+7ob
 t3VNM6RVl8xyWSRlm5ioev15CCOeWRi1nUT7m3UEBWpQ6ihJVpbjf1vVxZRW/E0t
 cgC+XzjSg26sWx1bSH9lGPFytOblAcZ04GG/Kpz02MmTgMiTdODFZ67AsqtdeQS7
 a9wpaQ+DgTqU0VcQx8Kdq8uy9MOztkhXn5yO8fEWjpm0lPcxjhJS4EpN+Ru2T7/Z
 AMuy5lRJfQzAPU9kY7TE0yZ07pgpZgh7LlWOoKtGD7UklzXVVZrVlpn7bApRN5vg
 ZLze5OiEiIF5gIiRC8sIyQ9TZdvg4NqwebCqspINixqs7iIpB7TG93WQcy82osSE
 TXhtx4Sy
 =ZjwY
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
 "Some of the larger changes this merge window:

   - Removal of drivers for Exynos5440, a Samsung SoC that never saw
     widespread use.

   - Uniphier support for USB3 and SPI reset handling

   - Syste control and SRAM drivers and bindings for Allwinner platforms

   - Qualcomm AOSS (Always-on subsystem) reset controller drivers

   - Raspberry Pi hwmon driver for voltage

   - Mediatek pwrap (pmic) support for MT6797 SoC"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
  drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
  soc: fsl: cleanup Kconfig menu
  soc: fsl: dpio: Convert DPIO documentation to .rst
  staging: fsl-mc: Remove remaining files
  staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
  staging: fsl-dpaa2: eth: move generic FD defines to DPIO
  soc: fsl: qe: gpio: Add qe_gpio_set_multiple
  usb: host: exynos: Remove support for Exynos5440
  clk: samsung: Remove support for Exynos5440
  soc: sunxi: Add the A13, A23 and H3 system control compatibles
  reset: uniphier: add reset control support for SPI
  cpufreq: exynos: Remove support for Exynos5440
  ata: ahci-platform: Remove support for Exynos5440
  soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
  soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
  soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
  soc: mediatek: pwrap: fix cipher init setting error
  dt-bindings: pwrap: mediatek: add pwrap support for MT6797
  reset: uniphier: add USB3 core reset control
  dt-bindings: reset: uniphier: add USB3 core reset support
  ...
2018-08-23 13:52:46 -07:00
Linus Torvalds 9e259f9352 ARM: 32-bit SoC platform updates
Most of the SoC updates in this cycle are cleanups and moves to more
 modern infrastructure:
  - Davinci was moved to common clock framework
  - OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
    keyboard interface (bitbanged AT keyboard via GPIO).
  - Removal of some stale code for Renesas platforms
  - Power management improvements for i.MX6LL
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlt+Lh0PHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3Y+YP/2QVT1T1/Fz3WsuLg7BYa6r51BDxvr/pSQKh
 eqLhZCcI5RpOlW4noWgJXWqnX2AlR1vX6xe0W0ebj177ttUHmidUQUJCpwP39AGE
 LrVC2+mlFb3uPx0HlpHsx3zFZdNFfrhl5mN3JbZfnLv0fUibVEhR+K8ii7MV1/Fk
 Lbo9sVPT8GIJuU6uyTTUnsCufwCkARMhrYbO6cbtS0FCO77a5aHp7btvHZ2ykxwh
 hG9CI3FhfAP3Tkpm+IbHkC5jYQNRewQoqthzJ4WJbRrcdA/vaArBTOUoZG4NFMOM
 M3B4jd1x26llmQhUqH4kGeOZiQ714GPrKcGS+8w7Twj5sIRGDxpif2Ac0kKL2B8X
 Ps6UTM0cb63W9I+TphjLysKSarNjR2lVVhNVoJ8P47MSyDGIRpSR7+IWvlJ7U8vz
 1yMWCguwrwZH3DnQb8UINTfI1Y1RstmtO5v8paSqfJyFX5r64x6VfYso1fRzxyFE
 4r2TS0HRv117aKkHwY8smjielZ0CpGnyEDQgq9Z72V4FueIqsJQrA3oGYXgTArFl
 mLL+fJUdwPv00nWuAZ8q0wIj1NvJvksJy+cObZXL6HK9m3cSdYwOHipdG86k20S5
 6/KMPmgrMbV9YO3lVtfJZjdu2QTBiYVBPGfsiSo5lVL5Q5rDYV9QBijnE+9W9/yT
 tJ038MhK
 =ACVk
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM 32-bit SoC platform updates from Olof Johansson:
 "Most of the SoC updates in this cycle are cleanups and moves to more
  modern infrastructure:

   - Davinci was moved to common clock framework

   - OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
     keyboard interface (bitbanged AT keyboard via GPIO).

   - Removal of some stale code for Renesas platforms

   - Power management improvements for i.MX6LL"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (112 commits)
  ARM: uniphier: select RESET_CONTROLLER
  arm64: uniphier: select RESET_CONTROLLER
  ARM: uniphier: remove empty Makefile
  ARM: exynos: Clear global variable on init error path
  ARM: exynos: Remove outdated maintainer information
  ARM: shmobile: Always enable ARCH_TIMER on SoCs with A7 and/or A15
  ARM: shmobile: r8a7779: hide unused r8a7779_platform_cpu_kill
  soc: r9a06g032: don't build SMP files for non-SMP config
  ARM: shmobile: Add the R9A06G032 SMP enabler driver
  ARM: at91: pm: configure wakeup sources for ULP1 mode
  ARM: at91: pm: add PMC fast startup registers defines
  ARM: at91: pm: Add ULP1 mode support
  ARM: at91: pm: Use ULP0 naming instead of slow clock
  ARM: hisi: handle of_iomap and fix missing of_node_put
  ARM: hisi: check of_iomap and fix missing of_node_put
  ARM: hisi: fix error handling and missing of_node_put
  ARM: mx5: Set the DBGEN bit in ARM_GPC register
  ARM: imx51: Configure M4IF to avoid visual artifacts
  ARM: imx: call imx6sx_cpuidle_init() conditionally for 6sll
  ARM: imx: fix i.MX6SLL build
  ...
2018-08-23 13:44:43 -07:00
Linus Torvalds db06f826ec The new and exciting feature this time around is in the clk core.
We've added duty cycle support to the clk API so that clk signal
 duty cycle ratios can be adjusted while taking into account things
 like clk dividers and clk tree hierarchy. So far only one SoC has
 implemented support for this, but I expect there will be more to
 come in the future.
 
 Outside of the core, we have the usual pile of clk driver updates
 and additions. The Amlogic meson driver got the most lines in the
 diffstat this time around because it added support for a whole bunch
 of hardware and duty cycle configuration. After that the Rockchip PX30,
 Qualcomm SDM845, and Renesas SoC drivers fill in a majority of the diff.
 We're left with the collection of non-critical fixes after that. Overall
 it looks pretty quiet this time.
 
 Core:
  - Clk duty cycle support
  - Proper CLK_SET_RATE_GATE support throughout the tree
 
 New Drivers:
  - Actions Semi Owl series S700 SoC clk driver
  - Qualcomm SDM845 display clock controller
  - i.MX6SX ocram_s clk support
  - Uniphier NAND, USB3 PHY, and SPI clk support
  - Qualcomm RPMh clk driver
  - i.MX7D mailbox clk support
  - Maxim 9485 Programmable Clock Generator
  - Expose 32 kHz PLL on PXA SoCs
  - imx6sll GPIO clk gate support
  - Atmel at91 I2S audio clk support
  - SI544/SI514 clk on/off support
  - i.MX6UL GPIO clock gates in CCM CCGR
  - Renesas Crypto Engine clocks on R-Car H3
  - Renesas clk support for the new RZ/N1D SoC
  - Allwinner A64 display engine clock support
  - Support for Rockchip's PX30 SoC
  - Amlogic Meson axg PCIe and audio clocks
  - Amlogic Meson GEN CLK on gxbb, gxl and axg
 
 Updates:
  - Remove an unused variable from Exynos4412 ISP driver
  - Fix a thinko bug in SCMI clk division logic
  - Add missing of_node_put()s in some i.MX clk drivers
  - Tegra SDMMC clk jitter improvements with high speed signaling modes
  - SPDX tagging for qcom and cs2000-cp drivers
  - Stop leaking con ids in __clk_put()
  - Fix a corner case in fixed factor clk probing where node is in DT but
    parent clk is registered much later
  - Marvell Armada 3700 clk_pm_cpu_get_parent() had an invalid return value
  - i.MX clk init arrays removed in place of CLK_IS_CRITICAL
  - Convert to CLK_IS_CRITICAL for i.MX51/53 driver
  - Fix Tegra BPMP driver oops when xlating a NULL clk
  - Proper default configuration for vic03 and vde clks on Tegra124
  - Mark Tegra memory controller clks as critical
  - Fix array bounds clamp in Tegra's emc determine_rate() op
  - Ingenic i2s bit update and allow UDC clk to gate
  - Fix name of aspeed SDC clk define to have only one 'CLK'
  - Fix i.MX6QDL video clk parent
  - Critical clk markings for qcom SDM845
  - Fix Stratix10 mpu_free_clk and sdmmc_free_clk parents
  - Mark Rockchip's pclk_rkpwm_pmu as critical clock, due to it supplying
    the pwm used to drive the logic supply of the rk3399 core.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAlt0WD0RHHNib3lkQGtl
 cm5lbC5vcmcACgkQrQKIl8bklSX5jBAAlMLb0fqnuAGNJeXZDk5rsCa496LMyGWx
 ku7uLA2H68SlbSQqq8FUPoCjDZkmsu2CbOX1U2/H4HFDS0pqpPiV3mZNtSeacedp
 4Wf8yUB5G3xdq9QUCSX5LxMmEQoGeJ+gaTspBvM6sNvEMBR2kEMGBqUy768tnDTR
 qCQ8Q1jOU6l8IdFV0SZGssmZ+oFqOyQoJVquPWPkw1+p/2f1KyYIyG5J5FXGxgcR
 1XQITY/I/dShQ2wd+ZeDdt+GjZqIXQ06Pt3ruRG7HVP79Zt1XCRJd5dZ2lf+Wj8T
 1ul3TWCAMYZ8gCPebLMbBGzKvQJQJcDU6DpIZsrUDN+C6z7KCS9vqeCxP9cF+3jJ
 LOmA6cWE7z9Vkk9s0I0KJJ2Sw7wRoXzE5OJcwa/yousSz3s9cX+F8SAkdZs77oUF
 0XnzPsvwdHI/egQ4UrsStPHM/gOFhsQqo8vvm5xaaTR2AxLKBHuPa9oUv9YpO/P5
 J6FCst3qeY3Wp69fJ5/Z058OFOAt81dKXij2fZJBOO4KJy7Kse8Sz5ApybXVAbY5
 lfvx+KGMITFqLYrcRIQZmlCuoHcMwI0FtHr9Ens5GXdbrJ+W+FlvP43eLCA0ZmRx
 9DidemChj3k3PC3H6tbax/jzV4IIxZdyUoBJ1imL4uyhhaXp/qr45A/aGwNp8Q8a
 WvkIGm3epK4=
 =Mcn+
 -----END PGP SIGNATURE-----

Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
 "The new and exciting feature this time around is in the clk core.
  We've added duty cycle support to the clk API so that clk signal duty
  cycle ratios can be adjusted while taking into account things like clk
  dividers and clk tree hierarchy. So far only one SoC has implemented
  support for this, but I expect there will be more to come in the
  future.

  Outside of the core, we have the usual pile of clk driver updates and
  additions. The Amlogic meson driver got the most lines in the diffstat
  this time around because it added support for a whole bunch of
  hardware and duty cycle configuration. After that the Rockchip PX30,
  Qualcomm SDM845, and Renesas SoC drivers fill in a majority of the
  diff. We're left with the collection of non-critical fixes after that.
  Overall it looks pretty quiet this time.

  Core:
   - Clk duty cycle support
   - Proper CLK_SET_RATE_GATE support throughout the tree

  New Drivers:
   - Actions Semi Owl series S700 SoC clk driver
   - Qualcomm SDM845 display clock controller
   - i.MX6SX ocram_s clk support
   - Uniphier NAND, USB3 PHY, and SPI clk support
   - Qualcomm RPMh clk driver
   - i.MX7D mailbox clk support
   - Maxim 9485 Programmable Clock Generator
   - expose 32 kHz PLL on PXA SoCs
   - imx6sll GPIO clk gate support
   - Atmel at91 I2S audio clk support
   - SI544/SI514 clk on/off support
   - i.MX6UL GPIO clock gates in CCM CCGR
   - Renesas Crypto Engine clocks on R-Car H3
   - Renesas clk support for the new RZ/N1D SoC
   - Allwinner A64 display engine clock support
   - support for Rockchip's PX30 SoC
   - Amlogic Meson axg PCIe and audio clocks
   - Amlogic Meson GEN CLK on gxbb, gxl and axg

  Updates:
   - remove an unused variable from Exynos4412 ISP driver
   - fix a thinko bug in SCMI clk division logic
   - add missing of_node_put()s in some i.MX clk drivers
   - Tegra SDMMC clk jitter improvements with high speed signaling modes
   - SPDX tagging for qcom and cs2000-cp drivers
   - stop leaking con ids in __clk_put()
   - fix a corner case in fixed factor clk probing where node is in DT
     but parent clk is registered much later
   - Marvell Armada 3700 clk_pm_cpu_get_parent() had an invalid return
     value
   - i.MX clk init arrays removed in place of CLK_IS_CRITICAL
   - convert to CLK_IS_CRITICAL for i.MX51/53 driver
   - fix Tegra BPMP driver oops when xlating a NULL clk
   - proper default configuration for vic03 and vde clks on Tegra124
   - mark Tegra memory controller clks as critical
   - fix array bounds clamp in Tegra's emc determine_rate() op
   - Ingenic i2s bit update and allow UDC clk to gate
   - fix name of aspeed SDC clk define to have only one 'CLK'
   - fix i.MX6QDL video clk parent
   - critical clk markings for qcom SDM845
   - fix Stratix10 mpu_free_clk and sdmmc_free_clk parents
   - mark Rockchip's pclk_rkpwm_pmu as critical clock, due to it
     supplying the pwm used to drive the logic supply of the rk3399
     core"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (85 commits)
  clk: rockchip: Add pclk_rkpwm_pmu to PMU critical clocks in rk3399
  clk: cs2000-cp: convert to SPDX identifiers
  clk: scmi: Fix the rounding of clock rate
  clk: qcom: Add display clock controller driver for SDM845
  clk: mvebu: armada-37xx-periph: Remove unused var num_parents
  clk: samsung: Remove unused mout_user_aclk400_mcuisp_p4x12 variable
  clk: actions: Add S700 SoC clock support
  dt-bindings: clock: Add S700 support for Actions Semi Soc's
  clk: actions: Add missing REGMAP_MMIO dependency
  clk: uniphier: add clock frequency support for SPI
  clk: uniphier: add more USB3 PHY clocks
  clk: uniphier: add NAND 200MHz clock
  clk: tegra: make sdmmc2 and sdmmc4 as sdmmc clocks
  clk: tegra: Add sdmmc mux divider clock
  clk: tegra: Refactor fractional divider calculation
  clk: tegra: Fix includes required by fence_udelay()
  clk: imx6sll: fix missing of_node_put()
  clk: imx6ul: fix missing of_node_put()
  clk: imx: add ocram_s clock for i.mx6sx
  clk: mvebu: armada-37xx-periph: Fix wrong return value in get_parent
  ...
2018-08-15 21:41:21 -07:00
Stephen Boyd ac7da1b787 Merge branches 'clk-actions-s700', 'clk-exynos-unused', 'clk-qcom-dispcc-845', 'clk-scmi-round' and 'clk-cs2000-spdx' into clk-next
* clk-actions-s700:
  :  - Actions Semi Owl series S700 SoC clk driver
  clk: actions: Add S700 SoC clock support
  dt-bindings: clock: Add S700 support for Actions Semi Soc's
  clk: actions: Add missing REGMAP_MMIO dependency

* clk-exynos-unused:
  :  - Remove an unused variable from Exynos4412 ISP driver
  clk: samsung: Remove unused mout_user_aclk400_mcuisp_p4x12 variable

* clk-qcom-dispcc-845:
  :  - Qualcomm SDM845 display clock controller
  clk: qcom: Add display clock controller driver for SDM845
  dt-bindings: clock: Introduce QCOM Display clock bindings
  clk: qcom: Move frequency table macro to common file

* clk-scmi-round:
  :  - Fix a thinko bug in SCMI clk division logic
  clk: scmi: Fix the rounding of clock rate

* clk-cs2000-spdx:
  clk: cs2000-cp: convert to SPDX identifiers
2018-08-14 23:00:15 -07:00
Stephen Boyd 032405a754 Merge branches 'clk-imx6-ocram', 'clk-missing-put', 'clk-tegra-sdmmc-jitter', 'clk-allwinner' and 'clk-uniphier' into clk-next
* clk-imx6-ocram:
  :  - i.MX6SX ocram_s clk support
  clk: imx: add ocram_s clock for i.mx6sx

* clk-missing-put:
  :  - Add missing of_node_put()s in some i.MX clk drivers
  clk: imx6sll: fix missing of_node_put()
  clk: imx6ul: fix missing of_node_put()

* clk-tegra-sdmmc-jitter:
  :  - Tegra SDMMC clk jitter improvements with high speed signaling modes
  clk: tegra: make sdmmc2 and sdmmc4 as sdmmc clocks
  clk: tegra: Add sdmmc mux divider clock
  clk: tegra: Refactor fractional divider calculation
  clk: tegra: Fix includes required by fence_udelay()

* clk-allwinner:
  clk: sunxi-ng: add A64 compatible string
  dt-bindings: add compatible string for the A64 DE2 CCU
  clk: sunxi-ng: r40: Export video PLLs
  clk: sunxi-ng: r40: Allow setting parent rate to display related clocks
  clk: sunxi-ng: r40: Add minimal rate for video PLLs

* clk-uniphier:
  :  - Uniphier NAND, USB3 PHY, and SPI clk support
  clk: uniphier: add clock frequency support for SPI
  clk: uniphier: add more USB3 PHY clocks
  clk: uniphier: add NAND 200MHz clock
2018-08-14 22:58:53 -07:00
Stephen Boyd 4a18ef5bab Merge branches 'clk-qcom-rpmh', 'clk-qcom-spdx', 'clk-con-id-leak', 'clk-fixed-factor-populated' and 'clk-mvebu-periph-parent' into clk-next
* clk-qcom-rpmh:
  :  - Qualcomm RPMh clk driver
  clk: qcom: clk-rpmh: Add QCOM RPMh clock driver

* clk-qcom-spdx:
  :  - SPDX tagging for qcom
  clk: qcom: Update SPDX headers for common files

* clk-con-id-leak:
  :  - Stop leaking con ids in __clk_put()
  clk: core: Potentially free connection id

* clk-fixed-factor-populated:
  :  - Fix a corner case in fixed factor clk probing where node is in DT but
  :    parent clk is registered much later
  clk: clk-fixed-factor: Clear OF_POPULATED flag in case of failure

* clk-mvebu-periph-parent:
  :  - Marvell Armada 3700 clk_pm_cpu_get_parent() had an invalid return value
  clk: mvebu: armada-37xx-periph: Remove unused var num_parents
  clk: mvebu: armada-37xx-periph: Fix wrong return value in get_parent
2018-08-14 22:58:49 -07:00
Stephen Boyd d16adaf0b9 Merge branches 'clk-mvebu-spdx', 'clk-meson', 'clk-imx7d-mu', 'clk-imx-init-array-cleanup' and 'clk-rockchip' into clk-next
* clk-mvebu-spdx:
  clk: mvebu: armada-37xx-periph: switch to SPDX license identifier

* clk-meson:
  clk: meson: add gen_clk
  clk: meson: gxbb: remove HHI_GEN_CLK_CTNL duplicate definition
  clk: meson-axg: add clocks required by pcie driver
  clk: meson: remove unused clk-audio-divider driver
  clk: meson: stop rate propagation for audio clocks
  clk: meson: axg: add the audio clock controller driver
  clk: meson: add axg audio sclk divider driver
  clk: meson: add triple phase clock driver
  clk: meson: add clk-phase clock driver
  clk: meson: clean-up meson clock configuration
  clk: meson: remove obsolete register access
  clk: meson: expose GEN_CLK clkid
  clk: meson-axg: add pcie and mipi clock bindings
  dt-bindings: clock: add meson axg audio clock controller bindings
  clk: meson: audio-divider is one based
  clk: meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL

* clk-imx7d-mu:
  :  - i.MX7D mailbox clk support
  clk: imx7d: add IMX7D_MU_ROOT_CLK

* clk-imx-init-array-cleanup:
  :  - i.MX clk init arrays removed in place of CLK_IS_CRITICAL
  clk: imx6sx: remove clks_init_on array
  clk: imx6sl: remove clks_init_on array
  clk: imx6q: remove clks_init_on array

* clk-rockchip:
  clk: rockchip: Add pclk_rkpwm_pmu to PMU critical clocks in rk3399
  clk: rockchip: fix clk_i2sout parent selection bits on rk3399
  clk: rockchip: add clock controller for px30
  clk: rockchip: add support for half divider
  dt-bindings: add bindings for px30 clock controller
  clk: rockchip: add dt-binding header for px30
2018-08-14 22:58:45 -07:00
Stephen Boyd 139054634b Merge branches 'clk-imx-critical', 'clk-tegra-bpmp', 'clk-tegra-124', 'clk-tegra-critical' and 'clk-tegra-emc-oob' into clk-next
* clk-imx-critical:
  :  - Convert to CLK_IS_CRITICAL for i.MX51/53 driver
  clk: imx51-imx53: Include sizes.h to silence compile errors
  clk: imx51-imx53: Annotate critical clocks as CLK_IS_CRITICAL

* clk-tegra-bpmp:
  :  - Fix Tegra BPMP driver oops when some xlating a NULL clk
  clk: tegra: bpmp: Don't crash when a clock fails to register

* clk-tegra-124:
  :  - Proper default configuration for vic03 and vde clks on Tegra124
  clk: tegra: Make vde a child of pll_c3
  clk: tegra: Make vic03 a child of pll_c3

* clk-tegra-critical:
  :  - Mark Tegra memory controller clks as critical
  clk: tegra: Mark Memory Controller clock as critical

* clk-tegra-emc-oob:
  :  - Fix array bounds clamp in Tegra's emc determine_rate() op
  clk: tegra: emc: Avoid out-of-bounds bug
2018-08-14 22:58:42 -07:00
Stephen Boyd ea4f7872c7 Merge branches 'clk-ingenic-fixes', 'clk-max9485', 'clk-pxa-32k-pll', 'clk-aspeed' and 'clk-imx6sll-gpio' into clk-next
* clk-ingenic-fixes:
  :  - Ingenic i2s bit update and allow UDC clk to gate
  clk: ingenic: Add missing flag for UDC clock
  clk: ingenic: Fix incorrect data for the i2s clock

* clk-max9485:
  :  - Maxim 9485 Programmable Clock Generator
  clk: Add driver for MAX9485
  dts: clk: add devicetree bindings for MAX9485

* clk-pxa-32k-pll:
  :  - Expose 32 kHz PLL on PXA SoCs
  clk: pxa: export 32kHz PLL

* clk-aspeed:
  :  - Fix name of aspeed SDC clk define to have only one 'CLK'
  clk: aspeed: Fix SDCLK name

* clk-imx6sll-gpio:
  :  - imx6sll GPIO clk gate support
  clk: imx6sll: add GPIO LPCGs
2018-08-14 22:58:39 -07:00
Stephen Boyd b183c6887a Merge branches 'clk-imx6-video-parent', 'clk-qcom-sdm845-criticals', 'clk-renesas', 'clk-stratix10-fixes' and 'clk-atmel-i2s' into clk-next
* clk-imx6-video-parent:
  :  - Fix i.MX6QDL video clk parent
  clk: imx6: fix video_27m parent for IMX6QDL_CLK_CKO1_SEL

* clk-qcom-sdm845-criticals:
  :  - critical clk markings for qcom SDM845
  clk: qcom: Enable clocks which needs to be always on for SDM845

* clk-renesas:
  clk: renesas: Renesas R9A06G032 clock driver
  dt-bindings: clock: renesas,r9a06g032-sysctrl: documentation
  dt-bindings: clock: Add the r9a06g032-sysctrl.h file
  clk: renesas: r8a7795: Add CCREE clock
  clk: renesas: r8a7795: Add CR clock

* clk-stratix10-fixes:
  :  - Fix Stratix10 mpu_free_clk and sdmmc_free_clk parents
  clk: socfpga: stratix10: fix the sdmmc_free_clk mux
  clk: socfpga: stratix10: fix the parents of mpu_free_clk

* clk-atmel-i2s:
  :  - Atmel at91 I2S audio clk support
  clk: at91: add I2S clock mux driver
  dt-bindings: clk: at91: add an I2S mux clock
2018-08-14 22:58:35 -07:00
Stephen Boyd 5ef7748ba3 Merge branches 'clk-qcom-set-rate-gate', 'clk-core-set-rate-gate', 'clk-core-duty-cycle', 'clk-si-prepare' and 'clk-imx-gpio-gates' into clk-next
* clk-qcom-set-rate-gate:
  clk: qcom: drop CLK_SET_RATE_GATE from sdc clocks

* clk-core-set-rate-gate:
  clk: fix CLK_SET_RATE_GATE with clock rate protection

* clk-core-duty-cycle:
  clk: add duty cycle support

* clk-si-prepare:
  :  - SI544/SI514 clk on/off support
  clk-si514, clk-si544: Implement prepare/unprepare/is_prepared operations

* clk-imx-gpio-gates:
  :  - i.MX6UL GPIO clock gates in CCM CCGR
  clk: imx6ul: remove clks_init_on array
  clk: imx6ul: add GPIO clock gates
  dt-bindings: clock: imx6ul: Do not change the clock definition order
2018-08-14 22:58:30 -07:00
Linus Torvalds 747f62305d sound updates for 4.19
It's been busy summer weeks and hence lots of changes, partly for a
 few new drivers and partly for a wide range of fixes.
 Here are highlights:
 
 ALSA Core:
  - Fix rawmidi buffer management, code cleanup / refactoring
  - Fix the SG-buffer page handling with incorrect fallback size
  - Fix the stall at virmidi trigger callback with a large buffer;
    also offloading and code-refactoring along with it
  - Various ALSA sequencer code cleanups
 
 ASoC:
  - Deploy the standard snd_pcm_stop_xrun() helper in several drivers
  - Support for providing name prefixes to generic component nodes
  - Quite a few fixes for DPCM as it gains a bit wider use and more
    robust testing
  - Generalization of the DIO2125 support to a simple amplifier driver
  - Accessory detection support for the audio graph card
  - DT support for PXA AC'97 devices
  - Quirks for a number of new x86 systems
  - Support for AM Logic Meson, Everest ES7154, Intel systems with
    RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
 
 HD-audio:
  - Code refactoring in HD-audio ext codec codes to drop own classes;
    preliminary works for the upcoming legacy codec support
  - Generalized DRM audio component for the upcoming radeon / amdgpu
    support
  - Unification of mic mute-LED and GPIO support for various codecs
  - Further improvement of CA0132 codec support including Recon3D
  - Proper vga_switcheroo handling for AMD i-GPU
  - Update of model list in documentation
  - Fixups for another HP Spectre x360, Conexant codecs, power-save
    blacklist update
 
 USB-audio:
  - Fix the invalid sample rate setup with external clock
  - Support of UAC3 selector units and processing units
  - Basic UAC3 power-domain support
  - Support for Encore mDSD and Thesycon-based DSD devices
  - Preparation for future complete callback changes
 
 Firewire:
  - Add support for MOTU Traveler
 
 Misc:
  - The endianess notation fixes in various drivers
  - Add fall-through comment in lots of drivers
  - Various sparse warning fixes, e.g. about PCM format types
 -----BEGIN PGP SIGNATURE-----
 
 iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAltxhXUOHHRpd2FpQHN1
 c2UuZGUACgkQLtJE4w1nLE9BPxAAnJyKM2IcfVKanjFZQmM4w1gEM3nt+EBvbOF5
 155Mq5ELNLxwwCav0eyoeTVD+mB4UO1y9+64SK73dUzBvj7llILs8s5VNMg7KYn6
 MnYMo0UIDlvQ/ZwJzzpU04QZVOIHa5HK9XG+u+Fycr8YOCdhGD6m/zGiBStd/xGd
 Bvgw2eHF10l+zqN+Vf+1P2/ENRyNxLYpJYYC02zl0nfXP29ZY+CjicDoRvD8/97X
 Pe5Jcfj/4oJZlN0MMXfLLP0vaWbUyogG3a4mzVRC+wHG2FZ5hGfFb92mfT8Yce3H
 dq9eaih6zMMiDuP4ipClMv/0t64cA8HD+Du/Enq9Jc/g41QAU1JFzj4qi1Ga7S2w
 F80uWCedwZ5FLXYAAK2kIunIaaD5phD+8DegzchiVzL6eg7BLmi/Rsfg9VkuC1Ir
 ZZERtT07XCzwXke0IAQQ1yhTE/uMxqntCJlZ0FoohvIABgH0jvrpp/cdDYFdC3it
 TaNk9REAuCVjr2ket1Jrw6pKNgtry7cDkKFK5d8S5HTNFEL+sWwz2NcSdPNRIIFT
 aqeUWt/H1P5G25if/636UJtf+EtlRPqC2Eng8OpY8hitb2vB3trjY25T4a5x5FW5
 S4oTyVWmxa4Xxj4QMMhpo7jxxwsux8J1fghDCpEqekiwt72CyVP2UN/cU8HJL7kN
 IWqnZgg=
 =eTIC
 -----END PGP SIGNATURE-----

Merge tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound updates from Takashi Iwai:
 "It's been busy summer weeks and hence lots of changes, partly for a
  few new drivers and partly for a wide range of fixes.

  Here are highlights:

  ALSA Core:
   - Fix rawmidi buffer management, code cleanup / refactoring
   - Fix the SG-buffer page handling with incorrect fallback size
   - Fix the stall at virmidi trigger callback with a large buffer; also
     offloading and code-refactoring along with it
   - Various ALSA sequencer code cleanups

  ASoC:
   - Deploy the standard snd_pcm_stop_xrun() helper in several drivers
   - Support for providing name prefixes to generic component nodes
   - Quite a few fixes for DPCM as it gains a bit wider use and more
     robust testing
   - Generalization of the DIO2125 support to a simple amplifier driver
   - Accessory detection support for the audio graph card
   - DT support for PXA AC'97 devices
   - Quirks for a number of new x86 systems
   - Support for AM Logic Meson, Everest ES7154, Intel systems with
     RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707

  HD-audio:
   - Code refactoring in HD-audio ext codec codes to drop own classes;
     preliminary works for the upcoming legacy codec support
   - Generalized DRM audio component for the upcoming radeon / amdgpu
     support
   - Unification of mic mute-LED and GPIO support for various codecs
   - Further improvement of CA0132 codec support including Recon3D
   - Proper vga_switcheroo handling for AMD i-GPU
   - Update of model list in documentation
   - Fixups for another HP Spectre x360, Conexant codecs, power-save
     blacklist update

  USB-audio:
   - Fix the invalid sample rate setup with external clock
   - Support of UAC3 selector units and processing units
   - Basic UAC3 power-domain support
   - Support for Encore mDSD and Thesycon-based DSD devices
   - Preparation for future complete callback changes

  Firewire:
   - Add support for MOTU Traveler

  Misc:
   - The endianess notation fixes in various drivers
   - Add fall-through comment in lots of drivers
   - Various sparse warning fixes, e.g. about PCM format types"

* tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits)
  ASoC: adav80x: mark expected switch fall-through
  ASoC: da7219: Add delays to capture path to remove DC offset noise
  ALSA: usb-audio: Mark expected switch fall-through
  ALSA: mixart: Mark expected switch fall-through
  ALSA: opl3: Mark expected switch fall-through
  ALSA: hda/ca0132 - Add exit commands for Recon3D
  ALSA: hda/ca0132 - Change mixer controls for Recon3D
  ALSA: hda/ca0132 - Add Recon3D input and output select commands
  ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D
  ALSA: hda/ca0132 - Add Recon3D startup functions and setup
  ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio
  ALSA: hda/ca0132 - Add Recon3D pincfg
  ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D
  ALSA: hda/ca0132 - Add alt_functions unsolicited response
  ALSA: hda/ca0132 - Clean up ca0132_init function.
  ALSA: hda/ca0132 - Create mmio gpio function to make code clearer
  ASoC: wm_adsp: Make DSP name configurable by codec driver
  ASoC: wm_adsp: Declare firmware controls from codec driver
  ASoC: max98373: Added software reset register to readable registers
  ASoC: wm_adsp: Correct DSP pointer for preloader control
  ...
2018-08-14 14:10:30 -07:00
Linus Torvalds c2d9f5bc2d Merge branch 'clkdev' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM clkdev updates from Russell King:
 "A couple of cleanups for clkdev"

* 'clkdev' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8778/1: clkdev: don't call __of_clk_get_by_name() unnecessarily from clk_get()
  ARM: 8776/1: clkdev: Remove duplicated negative index check from __of_clk_get()
2018-08-13 19:15:48 -07:00
Bartosz Golaszewski 53ccb22b8d ARM: 8778/1: clkdev: don't call __of_clk_get_by_name() unnecessarily from clk_get()
The way this function is implemented caused some confusion when
converting the TI DaVinci platform to using the common clock framework.

Current kernel supports booting DaVinci boards both in device tree as
well as legacy, board-file mode. In the latter, we always end up
calling clk_get_sys() as of_node is NULL and __of_clk_get_by_name()
returns -ENOENT.

It was not obvious at first glance how clk_get(dev, NULL) will work in
board-file mode since we always call __of_clk_get_by_name(). Let's make
it clearer by checking if of_node is NULL and skipping right to
clk_get_sys().

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: David Lechner <david@lechnology.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2018-08-13 16:27:52 +01:00
Mark Brown 4aa5db22d3
Merge branch 'asoc-4.19' into asoc-next 2018-08-09 14:47:05 +01:00
Levin Du 640332d1a0 clk: rockchip: Add pclk_rkpwm_pmu to PMU critical clocks in rk3399
PWM2 is commonly used to control voltage of PWM regulator of VDD_LOG in
RK3399. On the Firefly-RK3399 board, PWM2 outputs 40 KHz square wave
from power on and the VDD_LOG is about 0.9V. When the kernel boots
normally into the system, the PWM2 keeps outputing PWM signal.

But the kernel hangs randomly after "Starting kernel ..." line on that
board. When it happens, PWM2 outputs high level which causes VDD_LOG
drops to 0.4V below the normal operating voltage.

By adding "pclk_rkpwm_pmu" to the rk3399_pmucru_critical_clocks array,
PWM clock is ensured to be prepared at startup and the PWM2 output is
normal. After repeated tests, the early boot hang is gone.

This patch works on both Firefly-RK3399 and ROC-RK3399-PC boards.

Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2018-08-06 23:46:52 +02:00
Kuninori Morimoto 67075b3cb8 clk: cs2000-cp: convert to SPDX identifiers
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-02 13:55:00 -07:00
Amit Daniel Kachhap 7a8655e19b clk: scmi: Fix the rounding of clock rate
This fix rounds the clock rate properly by using quotient and not
remainder in the calculation. This issue was found while testing HDMI
in the Juno platform.

Fixes: 6d6a1d82ea ("clk: add support for clocks provided by SCMI")
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-02 13:43:48 -07:00
Taniya Das 81351776c9 clk: qcom: Add display clock controller driver for SDM845
Add support for the display clock controller found on SDM845
based devices. This would allow display drivers to probe and
control their clocks.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Remove CLK_GET_RATE_NOCACHE everywhere]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-08-01 08:08:12 -07:00
Anders Roxell 8927c27b32 clk: mvebu: armada-37xx-periph: Remove unused var num_parents
When building armada-37xx-periph, num_parents isn't used in function
clk_pm_cpu_get_parent:
drivers/clk/mvebu/armada-37xx-periph.c: In function ‘clk_pm_cpu_get_parent’:
drivers/clk/mvebu/armada-37xx-periph.c:419:6: warning: unused variable ‘num_parents’ [-Wunused-variable]
  int num_parents = clk_hw_get_num_parents(hw);
      ^~~~~~~~~~~
Remove the declaration of num_parents to dispose the warning.

Fixes: 616bf80d38 ("clk: mvebu: armada-37xx-periph: Fix wrong return value in get_parent")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-27 09:55:43 -07:00
Krzysztof Kozlowski 96455f734b clk: samsung: Remove unused mout_user_aclk400_mcuisp_p4x12 variable
Remove unused 'mout_user_aclk400_mcuisp_p4x12' variable to fix GCC warning:

    drivers/clk/samsung/clk-exynos4412-isp.c:40:27: warning:
        'mout_user_aclk400_mcuisp_p4x12' defined but not used [-Wunused-const-variable=]

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-26 00:38:51 -07:00
Olof Johansson 692b12c756 Exynos5440 drivers removal
The Exynos5440 (quad-core A15 with GMAC, PCIe, SATA) was targeting
 server platforms but it did not make it to the market really.  There are
 no development boards with it and probably there are no real products
 neither.  The development for Exynos5440 ended in 2013 and since then
 the platform is in maintenance mode.
 
 Removing Exynos5440 makes our life slightly easier: less maintenance,
 smaller code, reduced number of quirks, no need to preserve DTB
 backward-compatibility.
 
 The Device Tree sources and some of the drivers for Exynos5440 were
 already removed.  This removes remaining drivers.
 -----BEGIN PGP SIGNATURE-----
 
 iQItBAABCAAXBQJbWKG7EBxrcnprQGtlcm5lbC5vcmcACgkQwTdm5oaLg9fNiA//
 U/dI+ihiIXHOxtrVRZXNGsmI5545pUqLI5uTE9utvD2j10Ef+T45wOzcJEtVN5ro
 +Mnqt32+LC0UfAo721Vfziu91t9HCYdeq6gFfgKS3mm5GPqqmsD7havl/UpT4jvL
 JZZLTPoInT2zJ0oZanzIRoM5I7KCOrUikkoVYEq9Z2/DupZ/S1GJLYXq1kY00eXS
 xrtNxTyhi6Hmg80h1u93jUfilWPuYvXAuTfK+nyHNXLDkVRAprEXEc0HCdKp0gKT
 hCEVd/k2+FsREQSCq5+dCTvYwa/FATqvwU/pKZmhSuN4GOM6b/0kFFvTt0sUswY3
 ZFGnEhnXQ9JGHf3/1cXdRn3e/1/5vOyjchKzCdF5Pyo40HIvI1qSK4mhCSO355PO
 sIgI2OEEBCqVuu4HUeWDu13M7Q4haSHRCtqVyulT2LsNGRrm3Ko13lCz+knanMqH
 4Cs7dLSz4ZqCSC4XYs8lnUvOFu2e/71vYs39QMi9yGro9Wn5T7H4qPNLVUuMER3K
 Hwrj5CpGKqBnMt3qFAfsxB0CnHU+yIRb55qp9nTZSUzZ9B++qnDhoDd1ikYtc/yh
 EHAnszKGPox2JbBzJRRQtpUq+qegnFaAkjssZf2eY89KKkjw/sHtssMA60dpV1tY
 txpP7KiTiM3Cq0/Jdqi5D2kiiiFtpABo1Jb3CLzxlTk=
 =3x4x
 -----END PGP SIGNATURE-----

Merge tag 'samsung-drivers-exynos5440-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers

Exynos5440 drivers removal

The Exynos5440 (quad-core A15 with GMAC, PCIe, SATA) was targeting
server platforms but it did not make it to the market really.  There are
no development boards with it and probably there are no real products
neither.  The development for Exynos5440 ended in 2013 and since then
the platform is in maintenance mode.

Removing Exynos5440 makes our life slightly easier: less maintenance,
smaller code, reduced number of quirks, no need to preserve DTB
backward-compatibility.

The Device Tree sources and some of the drivers for Exynos5440 were
already removed.  This removes remaining drivers.

* tag 'samsung-drivers-exynos5440-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  usb: host: exynos: Remove support for Exynos5440
  clk: samsung: Remove support for Exynos5440
  cpufreq: exynos: Remove support for Exynos5440
  ata: ahci-platform: Remove support for Exynos5440

Signed-off-by: Olof Johansson <olof@lixom.net>
2018-07-26 00:17:51 -07:00
Saravanan Sekar d47317ca4a clk: actions: Add S700 SoC clock support
Add Actions Semi S700 SoC clock support

Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 16:40:54 -07:00
Saravanan Sekar d017c1f16a clk: actions: Add missing REGMAP_MMIO dependency
Add REGMAP_MMIO as dependency to avoid undefined
reference to regmap symbols.

Fixes: d85d20053e ("clk: actions: Add S900 SoC clock support")
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 16:40:52 -07:00
Kunihiko Hayashi ff388ee365 clk: uniphier: add clock frequency support for SPI
Add clock control for SPI controller on UniPhier SoCs.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 16:26:18 -07:00
Masahiro Yamada 9d222574ef clk: uniphier: add more USB3 PHY clocks
Add USB3 PHY clocks where missing.  Use fixed-factor clocks for those
without gating.

For clarification, prefix clock names with 'ss' or 'hs'.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 15:45:32 -07:00
Masahiro Yamada 0316c018c5 clk: uniphier: add NAND 200MHz clock
The Denali NAND controller IP needs three clocks:

 - clk: controller core clock

 - clk_x: bus interface clock

 - ecc_clk: clock at which ECC circuitry is run

Currently, only the first one (50MHz) is provided.  The rest of the
two clock ports must be connected to the 200MHz clock line.  Add this.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 15:45:25 -07:00
Peter De-Schrijver c76a69e477 clk: tegra: make sdmmc2 and sdmmc4 as sdmmc clocks
These clocks have low jitter paths to certain parents. To model these
correctly, use the sdmmc mux divider clock type.

Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 14:26:22 -07:00
Peter De-Schrijver 633e79650b clk: tegra: Add sdmmc mux divider clock
Add a clock type to model the sdmmc switch divider clocks which have paths
to source clocks bypassing the divider (Low Jitter paths). These
are handled by selecting the lj path when the divider is 1 (ie the
rate is the parent rate), otherwise the normal path with divider
will be selected. Otherwise this clock behaves as a normal peripheral
clock.

Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 13:45:09 -07:00
Peter De Schrijver cb3ac5947a clk: tegra: Refactor fractional divider calculation
Move this to a separate file so it can be used to calculate the sdmmc
clock dividers.

Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 13:43:34 -07:00
Aapo Vienamo 0cbb61a313 clk: tegra: Fix includes required by fence_udelay()
Add the missing linux/delay.h include statement for udelay() used by
fence_udelay() macro.

Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 13:43:13 -07:00
Nicholas Mc Guire 7f5eac5934 clk: imx6sll: fix missing of_node_put()
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 4a5f720b65 ("clk: imx: add clock driver for imx6sll")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 13:35:00 -07:00
Nicholas Mc Guire 11177e7a7a clk: imx6ul: fix missing of_node_put()
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 787b4271a6 ("clk: imx: add imx6ul clk tree support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 13:34:57 -07:00
Anson Huang d7b7c00dad clk: imx: add ocram_s clock for i.mx6sx
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, and its clock gate in CCM CCGR1 CG14
needs to be enabled before access, add it to
clock tree.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 09:44:58 -07:00
Gregory CLEMENT 616bf80d38 clk: mvebu: armada-37xx-periph: Fix wrong return value in get_parent
The return value of the get_parent operation is a u8, whereas a -EINVAL
was returned. This wrong value was return if the value was bigger that
the number of parent but this case was already handled by the core.

So we can just remove this chunk of code to fix the issue.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 9818a7a4fd ("clk: mvebu: armada-37xx-periph: prepare cpu clk to
be used with DVFS")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 09:42:50 -07:00
Rajan Vaja f6dab4233d clk: clk-fixed-factor: Clear OF_POPULATED flag in case of failure
Fixed factor clock has two initializations at of_clk_init() time
and during platform driver probe. Before of_clk_init() call,
node is marked as populated and so its probe never gets called.

During of_clk_init() fixed factor clock registration may fail if
any of its parent clock is not registered. In this case, it doesn't
get chance to retry registration from probe. Clear OF_POPULATED
flag if fixed factor clock registration fails so that clock
registration is attempted again from probe.

Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 09:36:46 -07:00
Mikko Perttunen 365f7a89c8 clk: core: Potentially free connection id
Patch "clk: core: Copy connection id" made it so that the connector id
'con_id' is kstrdup_const()ed to cater to drivers that pass non-constant
connection ids. The patch added the corresponding kfree_const to
__clk_free_clk(), but struct clk's can be freed also via __clk_put().
Add the kfree_const call to __clk_put() and add comments to both
functions to remind that the logic in them should be kept in sync.

Fixes: 253160a8ad ("clk: core: Copy connection id")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 09:29:12 -07:00
Taniya Das f9419783a6 clk: qcom: Update SPDX headers for common files
SPDX headers updated for common/branch/pll/regmap files.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-25 09:23:33 -07:00
Krzysztof Kozlowski fb174b27e8 clk: samsung: Remove support for Exynos5440
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Sylwester Nawrocki <snawrocki@kernel.org>
2018-07-24 18:43:52 +02:00
Taniya Das 9c7e47025a clk: qcom: clk-rpmh: Add QCOM RPMh clock driver
Add the RPMh clock driver to control the RPMh managed clock resources on
some of the Qualcomm Technologies, Inc. SoCs.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Clean up whitespace, indentation, remove
cmd_db_ready check]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-16 10:25:04 -07:00
Joel Stanley 565b9937f4 clk: aspeed: Support HPLL strapping on ast2400
The HPLL can be configured through a register (SCU24), however some
platforms chose to configure it through the strapping settings and do
not use the register. This was not noticed as the logic for bit 18 in
SCU24 was confused: set means programmed, but the driver read it as set
means strapped.

This gives us the correct HPLL value on Palmetto systems, from which
most of the peripheral clocks are generated.

Fixes: 5eda5d79e4 ("clk: Add clock driver for ASPEED BMC SoCs")
Cc: stable@vger.kernel.org # v4.15
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-11 09:34:25 -07:00
Geert Uytterhoeven 76672e2e5b ARM: 8776/1: clkdev: Remove duplicated negative index check from __of_clk_get()
__of_clk_get() calls of_parse_phandle_with_args(), which rejects
negative indices since commit bd69f73f2c ("of: Create function for
counting number of phandles in a property").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2018-07-11 11:02:48 +01:00
Faiz Abbas 91c17a7006 clk: ti: dra7: Add clkctrl clock data for the mcan clocks
Add clkctrl data for the m_can clocks and register it within the
clkctrl driver

Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-07-09 22:30:48 -07:00
Oleksij Rempel 30343897d8 clk: imx7d: add IMX7D_MU_ROOT_CLK
This clock is needed for iMX mailbox driver

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-09 09:55:19 -07:00
Gregory CLEMENT 66c7bb7c41 clk: mvebu: armada-37xx-periph: switch to SPDX license identifier
Adopt the SPDX license identifier headers to ease license compliance
management.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-09 09:44:49 -07:00
Gregory CLEMENT 61c40f35f5 clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to 1.2GHz
Switching the CPU from the L2 or L3 frequencies (300 and 200 Mhz
respectively) to L0 frequency (1.2 Ghz) requires a significant amount
of time to let VDD stabilize to the appropriate voltage. This amount of
time is large enough that it cannot be covered by the hardware
countdown register. Due to this, the CPU might start operating at L0
before the voltage is stabilized, leading to CPU stalls.

To work around this problem, we prevent switching directly from the
L2/L3 frequencies to the L0 frequency, and instead switch to the L1
frequency in-between. The sequence therefore becomes:

1. First switch from L2/L3(200/300MHz) to L1(600MHZ)
2. Sleep 20ms for stabling VDD voltage
3. Then switch from L1(600MHZ) to L0(1200Mhz).

It is based on the work done by Ken Ma <make@marvell.com>

Cc: stable@vger.kernel.org
Fixes: 2089dc33ea ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2018-07-09 09:44:06 -07:00