When building the kernel without passing the O= command line parameter
there's no point to use absolute paths for them.
Usually relative paths are preferred because they survive directory
moves, work across networked file systems and chrooted environments.
Absolute paths are still used if an output directory is given.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
a0c1e9073e "futex: runtime enable pi and
robust functionality" introduces a test wether futex in atomic stuff
works or not.
It does that by writing to address 0 of the kernel address space. This
will crash on older machines where addressing mode switching is enabled
but where the mvcos instruction is not available. Page table walking is
done by hand and therefore the code tries to access current->mm which
is NULL.
Therefore add an extra check, so we survive the early test.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
fix signal return code when enable CONFIG_OABI_COMPAT
Signed-off-by: Janboe Ye <janboe.ye@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the code required to register the F75375 device on the
GLAN Tank.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some bootloaders are disabling write buffer coalescing. Enable it back
under linux.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes the return value of omap_dma_chain_a_transfer
to 0 on success instead of the flag 'start_dma', which wasn't really useful
for anything.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although audio and dsp drivers are not integrated yet,
allow compiling in mailbox and mcbsp to see any build
warnings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO IRQ unmask doesn't actually do anything useful. The problem is
hidden by a separate explicit mass unmask at the end of the chained
bank handler.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PCI bridge representing the PCIE root complex on Axon, contains
device BARs for a memory range and ROM that define inbound accesses.
This confuses the kernel resource management code -- the resources
need to be hidden when Axon is a host bridge.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cell IOMMU code to parse the dma-ranges properties, used for the fixed
mapping, was broken in two ways for some devices.
Firstly it didn't cope with empty dma-ranges properties. An empty property
implies no translation so can be safely skipped.
The code also wrongly assumed it would be looking at PCI devices, and hard
coded the number of address and size cells.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The wrapper script didn't have entries for the TQM8540 board and the
SBC8548 or SBC8560 boards. I've assumed that the TQM8540 console is
8250 based and not CPM based by looking at its defconfig. There was
also a trailing * on the TQM8555 entry that I removed too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the PMU is an NMI now, it can come at any time we are only soft
disabled. We must hard disable around the two places we allow the kernel
stack SLB and r1 to go out of sync. Otherwise the PMU exception can
force a kernel stack SLB into another slot, which can lead to it
getting evicted, which can lead to a nasty unrecoverable SLB miss
in the exception entry code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PTRACE_SETREGS request was only recently added on powerpc,
and gdb does not use it. So it slipped through without getting
all the testing it should have had.
The user_regset changes had a simple bug in storing to all of
the 32-bit general registers block on 64-bit kernels. This bug
only comes up with PTRACE_SETREGS, not PPC_PTRACE_SETREGS.
It causes a BUG_ON to hit, so this fix needs to go in ASAP.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- move boot_args[] into the init section
- move $global$ into the read_mostly section
- fix the following two section mismatches:
WARNING: vmlinux.o(.text+0x9c): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
WARNING: vmlinux.o(.text+0xa0): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
Signed-off-by: Helge Deller <deller@gmx.de>
SIgned-off-by: Kyle McMartin <kyle@mcmartin.ca>
When we show_regs, we obviously have a struct pt_regs of the calling
frame. Use these in show_stack so we don't have the entire bogus call trace
up to the show_stack call.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This patch adds the known pa8900 CPUs to the inventory list and removes
the Crestone Peak one which apparently never escaped into the wild.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This patch moves the default parisc defconfig to
arch/parisc/configs/generic_defconfig where it belongs and selects it as
the default defconfig through KBUILD_DEFCONFIG.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Commit 721fdf3416 introduced a subtle bug
by accidently removing the "static" from iodc_dbuf. This resulted in, what
appeared to be, a trap without *current set to a task. Probably the result of
a trap in real mode while calling firmware.
Also do other misc clean ups. Since the only input from firmware is non
blocking, share iodc_dbuf between input and output, and spinlock the
only callers.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Originally, show_stack was used in BUG() output. However, a recent commit
changed it to print register state (no idea what that's supposed to help,
really...) and parisc was missing a backtrace because of it.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The printf string was broken in the same way the zImage one was before,
though the uImage managed to avoid getting fixed at that time. Do so now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (32 commits)
ACPI: thermal: show temperature in millidegree Celsius
thermal: fix generic thermal I/F for hwmon
acer-wmi: build depends on i8042
documentation: Move power-related files to Documentation/power/
ACPI: buffer array too short in drivers/acpi/system.c
acer-wmi: Add DMI quirk for mail LED support on Acer Aspire 3610/ 5610
acer-wmi: Fix DSDT path in documentation
acer-wmi: Make device detection error messages more descriptive
laptops: move laptop-mode.txt to Documentation/laptops/
ACPICA: Warn if packages with invalid references are evaluated
ACPI: add _PRT quirks to work around broken firmware
Hibernation: Fix mark_nosave_pages()
ACPI: Ignore _BQC object when registering backlight device
ACPI: WMI: Clean up handling of spec violating data blocks
acer-wmi: Don't warn if mail LED cannot be detected
acer-wmi: Rename mail LED correctly & remove hardcoded colour
ACPI: use ACPI_DEBUG_PRINT instead of printk in acpi_processor_hotplug_notify()
ACPI: button: make real parent for input devices in device tree
toshiba_acpi: Enable autoloading
ACPI: EC: Handle IRQ storm on Acer laptops
...
iommu_is_span_boundary in lib/iommu-helper.c was exported for PARISC IOMMUs
(commit 3715863aa1). Alpha's IOMMU can use it.
This removes the check on the boundary size alignment because
iommu_is_span_boundary does.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently the SH-2/SH-2A address error exception dispatch copies off the
register state from the stack and skips over the first register, skewing
the rest. Fix up the math here so that the proper register state is
handed down to the exception handler itself.
Signed-off-by: Kieran Bingham <kbingham@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
My recent hack to allocate the hash table under 1GB on cell was poorly
tested, *cough*. It turns out on blades with large amounts of memory we
fail to allocate the hash table at all. This is because RTAS has been
instantiated just below 768MB, and 0-x MB are used by the kernel,
leaving no areas that are both large enough and also naturally-aligned.
For the cell IOMMU hack the page tables must be under 2GB, so use that
as the limit instead. This has been tested on real hardware and boots
happily.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Once again, this time with feeling....
- Ted
>From c91cfaabc17f8a53807a2f31f067a732e34a1550 Mon Sep 17 00:00:00 2001
From: Theodore Ts'o <tytso@mit.edu>
Date: Wed, 12 Mar 2008 11:50:39 -0400
Subject: Export empty_zero_page
The empty_zero_page symbol is exported by most other architectures
(s390, ia64, x86, um), and an upcoming ext4 patch needs it because
ZERO_PAGE() references empty_zero_page, and we need it to zero out an
unitialized extents in ext4 files.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When building arch/powerpc/platforms/powermac/pic.c when !CONFIG_ADB_PMU
we get the following warnings:
arch/powerpc/platforms/powermac/pic.c: In function 'pmacpic_find_viaint':
arch/powerpc/platforms/powermac/pic.c:623: warning: label 'not_found' defined but not used
This fixes it.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bogus test for unassigned resources that came from our 32-bit
PCI code ended up being "merged" by my previous patch series,
breaking some 64-bit setups where devices have legal resources
ending at 0xffffffff.
This fixes it by completely changing the test. We now test for
res->start == 0, as the generic code expects, and we also only
do so on platforms that don't have the PPC_PCI_PROBE_ONLY flag
set, as there are cases of pSeries and iSeries where it could
be a valid value and those can't reassign devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pattern substitution rules were failing when used with zImage-dtb
targets. If zImage-dtb.initrd was selected, the pattern substitution
would generate "zImage.initrd-dtb" instead of "zImage-dtb.initrd" which
caused the build to fail.
This renames zImage-dtb to dtbImage to avoid the problem entirely.
By not using the zImage prefix then is no potential for namespace
collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers (such as V4L2) have code that causes gcc to generate
calls to __ucmpdi2 when compiling for 32-bit powerpc, which results
in either a link-time error or a module that can't be loaded, as
we don't currently have a __ucmpdi2. This adds one so these drivers
can be used.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move 00-INDEX entries to power/00-INDEX (and add entry for
pm_qos_interface.txt).
Update references to moved filenames.
Fix some trailing whitespace.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
With KBUILD_DEFCONFIG we don't have to ship a second copy of ip22_defconfig.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows a 48Hz clock to be selected on Malta and other systems. Note
this not normally a sensible option as it results in rather high latencies
for some kernel stuff.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some of these are architecturally required for R2 processors so lets try
to be bit closer to the real thing. This also provides access to the
CPU cycle timer, even on multiprocessors. In that aspect its currently
bug compatible to what would happen on a R2-based SMP.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
0 is a valid device id (DSCR_CMD0_UART0_TX), so we can't use it to mark
an empty entry in the device table. Use ~0 instead and search for id ~0
when looking for a free entry.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
quicklists cause a serious memory leak on 32-bit x86,
as documented at:
http://bugzilla.kernel.org/show_bug.cgi?id=9991
the reason is that the quicklist pool is a special-purpose
cache that grows out of proportion. It is not accounted for
anywhere and users have no way to even realize that it's
the quicklists that are causing RAM usage spikes. It was
supposed to be a relatively small pool, but as demonstrated
by KOSAKI Motohiro, they can grow as large as:
Quicklists: 1194304 kB
given how much trouble this code has caused historically,
and given that Andrew objected to its introduction on x86
(years ago), the best option at this point is to remove them.
[ any performance benefits of caching constructed pgds should
be implemented in a more generic way (possibly within the page
allocator), while still allowing constructed pages to be
allocated by other workloads. ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The code to restart syscalls after signals depends on checking for a
negative orig_ax, and for particular negative -ERESTART* values in ax.
These fields are 64 bits and for a 32-bit task they get zero-extended.
The syscall restart behavior is lost, a regression from a native 32-bit
kernel and from 64-bit tasks' behavior.
This patch fixes the problem by doing sign-extension where it matters.
For orig_ax, the only time the value should be -1 but winds up as
0x0ffffffff is via a 32-bit ptrace call. So the patch changes ptrace to
sign-extend the 32-bit orig_eax value when it's stored; it doesn't
change the checks on orig_ax, though it uses the new current_syscall()
inline to better document the subtle importance of the used of
signedness there.
The ax value is stored a lot of ways and it seems hard to get them all
sign-extended at their origins. So for that, we use the
current_syscall_ret() to sign-extend it only for 32-bit tasks at the
time of the -ERESTART* comparisons.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At present, we can hit the BUG_ON in __spu_update_sched_info by reading
the regs file of a context between two calls to spu_run. The
spu_release_saved called by spufs_regs_read() is resulting in the (now
non-runnable) context being placed back on the run queue, so the next
call to spu_run ends up in the bug condition.
This change uses the SPU_SCHED_SPU_RUN flag to only reschedule a context
if it's still in spu_run().
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
commit 4ef11014 introduced a usage of SCHED_IDLE to detect when
a context is within spu_run.
Instead of SCHED_IDLE (which has other meaning), add a flag to
sched_flags to tell if a context should be running.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
I figured out another ACPI related regression today.
randconfig testing triggered an early boot-time hang on a laptop of mine
(32-bit x86, config attached) - the screen was scrolling ACPI AML
exceptions [with no serial port and no early debugging available].
v2.6.24 works fine on that laptop with the same .config, so after a few
hours of bisection (had to restart it 3 times - other regressions
interacted), it honed in on this commit:
| 10270d4838 is first bad commit
|
| Author: Linus Torvalds <torvalds@woody.linux-foundation.org>
| Date: Wed Feb 13 09:56:14 2008 -0800
|
| acpi: fix acpi_os_read_pci_configuration() misuse of raw_pci_read()
reverting this commit ontop of -rc5 gave a correctly booting kernel.
But this commit fixes a real bug so the real question is, why did it
break the bootup?
After quite some head-scratching, the following change stood out:
- pci_id->bus = tu8;
+ pci_id->bus = val;
pci_id->bus is defined as u16:
struct acpi_pci_id {
u16 segment;
u16 bus;
...
and 'tu8' changed from u8 to u32. So previously we'd unconditionally
mask the return value of acpi_os_read_pci_configuration()
(raw_pci_read()) to 8 bits, but now we just trust whatever comes back
from the PCI access routines and only crop it to 16 bits.
But if the high 8 bits of that result contains any noise then we'll
write that into ACPI's PCI ID descriptor and confuse the heck out of the
rest of ACPI.
So lets check the PCI-BIOS code on that theory. We have this codepath
for 8-bit accesses (arch/x86/pci/pcbios.c:pci_bios_read()):
switch (len) {
case 1:
__asm__("lcall *(%%esi); cld\n\t"
"jc 1f\n\t"
"xor %%ah, %%ah\n"
"1:"
: "=c" (*value),
"=a" (result)
: "1" (PCIBIOS_READ_CONFIG_BYTE),
"b" (bx),
"D" ((long)reg),
"S" (&pci_indirect));
Aha! The "=a" output constraint puts the full 32 bits of EAX into
*value. But if the BIOS's routines set any of the high bits to nonzero,
we'll return a value with more set in it than intended.
The other, more common PCI access methods (v1 and v2 PCI reads) clear
out the high bits already, for example pci_conf1_read() does:
switch (len) {
case 1:
*value = inb(0xCFC + (reg & 3));
which explicitly converts the return byte up to 32 bits and zero-extends
it.
So zero-extending the result in the PCI-BIOS read routine fixes the
regression on my laptop. ( It might fix some other long-standing issues
we had with PCI-BIOS during the past decade ... ) Both 8-bit and 16-bit
accesses were buggy.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ahmed managed to crash the Host in release_pgd(), which cannot be a Guest
bug, and indeed it wasn't.
The bug was that handing a 0 as the address of the toplevel page table
being manipulated can cause the lookup code in find_pgdir() to return
an uninitialized cache entry (we shadow up to 4 top level page tables
for each Guest).
Commit 37cc8d7f96 introduced this
behaviour in the Guest, uncovering the bug.
The patch which he submitted (which removed the /4 from the index
calculation) simply ensured that these high-indexed entries hit the
early exit path of guest_set_pmd(). But you get lots of segfaults in
guest userspace as the PMDs aren't being updated.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now the TSC code handles a zero return from calculate_cpu_khz(),
lguest can simply pass through the value it gets from the Host: if
non-zero, all the normal TSC code applies.
Otherwise (or if the Host really doesn't support TSC), the clocksource
code will fall back to the slower but reasonable lguest clock.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The function was returning NULL the second time it was
called if the firmware was uploaded from the boot loader
or the first time it was called if the firmware was
uploaded from the kernel.
Signed-off-by: Ionut Nicu <ionut.nicu@freescale.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Not all e300 cores support the performance monitors, and the ones
that don't will be confused by the mf/mtpmr instructions. This
allows the support to be optional, so the 8349 can turn it off
while the 8379 can turn it on. Sadly, those aren't config options,
so it will be left to the defconfigs and the users to make that
determination.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes a boot panic due to a typo in the recent iommu patchset from
FUJITA Tomonori <tomof@acm.org> - the code used dma_get_max_seg_size()
instead of dma_get_seg_boundary().
It also removes a couple of unnecessary BUG_ON() and ALIGN() macros.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reported-and-tested-by: Bob Tracy <rct@frus.com>
Acked-by: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GPIO_MAX is the number of the last gpio, not the number of gpios. So
the bitmap must provide GPIO_MAX + 1 bits.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes 64-bit ptrace calls setting the 64-bit orig_ax field for a
32-bit task sign-extend the low 32 bits up to 64. This matches what a
64-bit debugger expects when tracing a 32-bit task.
This follows on my "x86_64 ia32 syscall restart fix". This didn't
matter until that was fixed.
The debugger ignores or zeros the high half of every register slot it
sets (including the orig_rax pseudo-register) uniformly. It expects
that the setting of the low 32 bits always has the same meaning as a
32-bit debugger setting those same 32 bits with native 32-bit
facilities.
This never arose before because the syscall restart check never
matched any -ERESTART* values due to lack of sign extension. Before
that fix, even 32-bit ptrace setting orig_eax to -1 failed to trigger
the restart check anyway. So this was never noticed as a regression
of 64-bit debuggers vs 32-bit debuggers on the same 64-bit kernel.
Signed-off-by: Roland McGrath <roland@redhat.com>
[ Changed to just do the sign-extension unconditionally on x86-64,
since orig_ax is always just a small integer and doesn't need
the full 64-bit range ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes swap routines operate correctly on the ppc_8xx based machines.
Recent kernel's size makes swap feature very important on low-memory platfor
those are actually non-operable without it.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following patch allows interrupts to occur on the
sbc8548. Currently PCI and PCI-X devices get assigned an IRQ
but the interrupt count never increases. This solves the
problem and adds PCI support as well.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new x86 setup code (4fd06960f1) broke booting on an old P3/500MHz
with an onboard Voodoo3 of mine. After debugging it, it turned out
to be caused by the fact that the vesa probing now asks for VBE2 data.
Disassembing the video BIOS shows that it overflows the vesa_general_info
structure when VBE2 data is requested because the source addresses for the
information strings which get strcpy'ed to the buffer lie outside the 32K
BIOS code (and hence contain long sequences of 0xff's).
E.G.:
get_vbe_controller_info:
00002A9C 60 pushaw
00002A9D 1E push ds
00002A9E 0E push cs
00002A9F 1F pop ds
00002AA0 2BC9 sub cx,cx
00002AA2 6626813D56424532 cmp dword [es:di],0x32454256 ; "VBE2"
00002AAA 7501 jnz .1
00002AAC 41 inc cx
.1:
00002AAD 51 push cx
00002AAE B91400 mov cx,0x14
00002AB1 BED47F mov si, controller_header
00002AB4 57 push di
00002AB5 F3A4 rep movsb ; copy vbe1.2 header
00002AB7 B9EC00 mov cx,0xec
00002ABA 2AC0 sub al,al
00002ABC F3AA rep stosb ; zero pad remainder
00002ABE 5F pop di
00002ABF E8EB0D call word get_memory
00002AC2 C1E002 shl ax,0x2
00002AC5 26894512 mov [es:di+0x12],ax ; total memory
00002AC9 26C745040003 mov word [es:di+0x4],0x300 ; VBE version
00002ACF 268C4D08 mov [es:di+0x8],cs
00002AD3 268C4D10 mov [es:di+0x10],cs
00002AD7 59 pop cx
00002AD8 E361 jcxz .done ; VBE2 requested?
00002ADA 8D9D0001 lea bx,[di+0x100]
00002ADE 53 push bx
00002ADF 87DF xchg bx,di ; di now points to 2nd half
00002AE1 26C747140001 mov word [es:bx+0x14],0x100 ; sw rev
00002AE7 26897F06 mov [es:bx+0x6],di ; oem string
00002AEB 268C4708 mov [es:bx+0x8],es
00002AEF BE5280 mov si,0x8052 ; oem string
00002AF2 E87A1B call word strcpy
00002AF5 26897F0E mov [es:bx+0xe],di ; video mode list
00002AF9 268C4710 mov [es:bx+0x10],es
00002AFD B91E00 mov cx,0x1e
00002B00 BEE87F mov si,vidmodes
00002B03 F3A5 rep movsw
00002B05 26897F16 mov [es:bx+0x16],di ; oem vendor
00002B09 268C4718 mov [es:bx+0x18],es
00002B0D BE2480 mov si,0x8024 ; oem vendor
00002B10 E85C1B call word strcpy
00002B13 26897F1A mov [es:bx+0x1a],di ; oem product
00002B17 268C471C mov [es:bx+0x1c],es
00002B1B BE3880 mov si,0x8038 ; oem product
00002B1E E84E1B call word strcpy
00002B21 26897F1E mov [es:bx+0x1e],di ; oem product rev
00002B25 268C4720 mov [es:bx+0x20],es
00002B29 BE4580 mov si,0x8045 ; oem product rev
00002B2C E8401B call word strcpy
00002B2F 58 pop ax
00002B30 B90001 mov cx,0x100
00002B33 2BCF sub cx,di
00002B35 03C8 add cx,ax
00002B37 2AC0 sub al,al
00002B39 F3AA rep stosb ; zero pad
.done:
00002B3B 1F pop ds
00002B3C 61 popaw
00002B3D B84F00 mov ax,0x4f
00002B40 C3 ret
(The full BIOS can be found at http://peter.korsgaard.com/vgabios.bin
if interested).
The old setup code didn't ask for VBE2 info, and the new code doesn't
actually do anything with the extra information, so the fix is to simply
not request it. Other BIOS'es might have the same problem.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Beulich noticed that the reboot fixups went missing during
reboot.c unification.
(commit 4d022e35fd)
Geode and a few other rare boards with special reboot quirks are
affected.
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
convert_fxsr_to_user() in 2.6.24's i387_32.c did this, and
convert_to_fxsr() also does the inverse, so I assume it's an oversight
that it is no longer being done.
[ mingo@elte.hu:
we encode it this way because there's no space for the 'FPU Last
Instruction Opcode' (->fop) field in the legacy user_i387_ia32_struct
that PTRACE_GETFPREGS/PTRACE_SETFPREGS uses.
it's probably pure legacy - i'd be surprised if any user-space relied on
the FPU Last Opcode in any way. But indeed we used to do it previously
so the most conservative thing is to preserve that piece of information.
]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Linux kernel currently does not clear the direction flag before
calling a signal handler, whereas the x86/x86-64 ABI requires that.
Linux had this behavior/bug forever, but this becomes a real problem
with gcc version 4.3, which assumes that the direction flag is
correctly cleared at the entry of a function.
This patches changes the setup_frame() functions to clear the
direction before entering the signal handler.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes the following bug:
http://ozlabs.org/pipermail/linuxppc-dev/2008-February/051979.html
Separate defconfigs are no longer needed now that CONFIG_DEVICE_TREE is gone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This makes swap routines operate correctly on the ppc_8xx based machines.
Code has been revalidated on mpc885ads (8M sdram) with recent kernel. Based
on patch from Yuri Tikhonov <yur@emcraft.com> to do the same on arch/ppc
instance.
Recent kernel's size makes swap feature very important on low-memory platforms,
those are actually non-operable without it.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
[Blackfin] arch: current_l1_stack_save is a pointer, so use NULL rather than 0
[Blackfin] arch: fix atomic and32/xor32 comments and ENDPROC markings
[Blackfin] arch: fix bug - allow SDH driver to be used as module
[Blackfin] arch: to kill syscalls missing warning by adding new timerfd syscalls
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kprobes arch consolidation build fix
[IA64] update efi region debugging to use MB, GB and TB as well as KB
[IA64] use dev_printk in video quirk
[IA64] remove remaining __FUNCTION__ occurrences
[IA64] remove unnecessary nfs includes from sys_ia32.c
[IA64] remove CONFIG_SMP ifdef in ia64_send_ipi()
[IA64] arch_ptrace() cleanup
[IA64] remove duplicate code from arch_ptrace()
[IA64] convert sys_ptrace to arch_ptrace
[IA64] remove find_thread_for_addr()
[IA64] do not sync RBS when changing PT_AR_BSP or PT_CFM
[IA64] access user RBS directly
ia64 named their handler kprobes_fault_handler while all other
arches used kprobe_fault_handler. Change the function definition
and header declaration.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When EFI_DEBUG is defined to a non-zero value in arch/ia64/kernel/efi.c,
the efi memory regions are displayed. This patch enhances the
display code in a few ways:
1. Use TB, GB and MB as well as KB as units.
Although this introduces rounding errors (KB doesn't as
size is always a multiple of 4Kb), it does make
things a lot more readable.
Also as the range is also shown, it is possible to note the exact size
if it is important. In my experience, the size field is mostly useful
for getting a general idea of the size of a region.
On the rx2620 that I use, there actually is an 8TB region (though not
backed by physical memory, and 8TB really is a lot more readable than
8589934592KB.
2. pad the size field with leading spaces to further improve readability
...
... ( 8MB)
... ( 928MB)
... ( 3MB)
...
vs
...
... (8MB)
... (928MB)
... (3MB)
...
3. Pad the attr field out to 64bits using leading zeros,
to further improve readability.
...
mem05: type= 2, attr=0x0000000000000008, range=[0x0000000004000000-0x000000000481f000) ( 8MB)
mem06: type= 7, attr=0x0000000000000008, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) ( 3MB)
mem08: type= 4, attr=0x0000000000000008, range=[0x000000003eb8e000-0x000000003ee7a000) ( 2MB)
...
...
mem05: type= 2, attr=0x8, range=[0x0000000004000000-0x000000000481f000) ( 8MB)
mem06: type= 7, attr=0x8, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) ( 3MB)
mem08: type= 4, attr=0x8, range=[0x000000003eb8e000-0x000000003ee7a000) ( 2MB)
...
4. Use %d instead of %u for the index field, as i is a signed int.
N.B: This code is not compiled unless EFI_DEBUG is non 0.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
__FUNCTION__ is gcc-specific, use __func__
Long lines have been kept where they exist, some small spacing changes
have been done.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Compilation of 2.6.25-rc2-mm1 on ia64 generates many warnings.
IA64 support 2 ELF format (IA64 binary and IA32 binary),
thus if 2 elf related header included, cause many warning or error.
about 2 week ago, J. Bruce Fields proposed this problem fixed patch.
(http://marc.info/?l=linux-ia64&m=120329313305695&w=2)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When !CONFIG_SMP, cpu_physical_id() is ia64_get_lid(), which is
functionally identical to
(ia64_getreg(_IA64_REG_CR_LID) >> 16) & 0xffff
so there's no need for two versions of this code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Correct GPIO pin assignment for the LCD power control (PCI)
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Franck Bui-Huu