SW can trigger MIPI pads calibration any time after power on
but calibration results will be latched and applied to the pads
by MIPI CAL unit only when the link is in LP-11 state and then
status register will be updated.
For CSI, trigger of pads calibration happen during CSI stream
enable where CSI receiver is kept ready prior to sensor or CSI
transmitter stream start.
So, pads may not be in LP-11 at this time and waiting for the
calibration to be done immediate after calibration start will
result in timeout.
This patch splits tegra_mipi_calibrate() and tegra_mipi_wait()
so triggering for calibration and waiting for it to complete can
happen at different stages.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra CSI driver need a separate MIPI device for each channel as
calibration of corresponding MIPI pads for each channel should
happen independently.
So, this patch updates tegra_mipi_request() API to add a device_node
pointer argument to allow creating mipi device for specific device
node rather than a device.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra driver uses empty implementations for its encoders. Replace
the code with the generic simple encoder.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305155950.2705-16-tzimmermann@suse.de
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail) there is no need to check the
return value of drm_debugfs_create_files(). Therefore, remove the
return checks and error handling of the drm_debugfs_create_files()
function from various debugfs init functions in drm/tegra and have
them return 0 directly.
v2: remove conversion of tegra_debugfs_init() to void to avoid build
breakage.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-2-wambui.karugax@gmail.com
The Tegra DRM driver heavily relies on the implementations for runtime
suspend/resume to be called at specific times. Unfortunately, there are
some cases where that doesn't work. One example is if the user disables
runtime PM for a given subdevice. Another example is that the PM core
acquires a reference to runtime PM during system sleep, effectively
preventing devices from going into low power modes. This is intentional
to avoid nasty race conditions, but it also causes system sleep to not
function properly on all Tegra systems.
Fix this by not implementing runtime PM at all. Instead, a minimal,
reference-counted suspend/resume infrastructure is added to the host1x
bus. This has the benefit that it can be used regardless of the system
power state (or any transitions we might be in), or whether or not the
user allows runtime PM.
Atomic modesetting guarantees that these functions will end up being
called at the right point in time, so the pitfalls for the more generic
runtime PM do not apply here.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the host1x clients' parent to "host" because that more closely
describes what it is. The parent can be confused with the parent device
in terms of the device hierarchy. Subsequent patches will add a new
member that refers to the parent in that hierarchy.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop use of the deprecated drmP.h header file.
For all touched files divide include files into blocks,
and sort them within the blocks.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-3-sam@ravnborg.org
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
The regulator is controlled as part of runtime PM, so it should not be
additionally disabled from the ->exit() callback.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ->late_register() and ->early_unregister() callbacks are called at
the right time to make sure userspace only accesses interfaces when it
should. Move debugfs registration and unregistration to these callback
functions to avoid potential races with userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
After commit 75af8fa7fd ("drm/tegra: dsi: Trace register accesses"),
the debugfs register dump implementation causes excessive stack usage
and can result in build warnings. To fix this, move the register
definitions into a table and iterate over the table while dumping the
registers to debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This contains a couple of fixes and improvements for host1x, with some
preparatory work for Tegra186 support.
The remainder is cleanup and minor bugfixes for Tegra DRM along with
enhancements to debuggability.
There have also been some enhancements to the kernel interfaces for
host1x job submissions and support for mmap'ing PRIME buffers directly,
all of which get the interfaces very close to ready for serious work.
-----BEGIN PGP SIGNATURE-----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=ZaxL
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.14-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.14-rc1
This contains a couple of fixes and improvements for host1x, with some
preparatory work for Tegra186 support.
The remainder is cleanup and minor bugfixes for Tegra DRM along with
enhancements to debuggability.
There have also been some enhancements to the kernel interfaces for
host1x job submissions and support for mmap'ing PRIME buffers directly,
all of which get the interfaces very close to ready for serious work.
* tag 'drm/tegra/for-4.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (21 commits)
drm/tegra: Prevent BOs from being freed during job submission
drm/tegra: gem: Implement mmap() for PRIME buffers
drm/tegra: Support render node
drm/tegra: sor: Trace register accesses
drm/tegra: dpaux: Trace register accesses
drm/tegra: dsi: Trace register accesses
drm/tegra: hdmi: Trace register accesses
drm/tegra: dc: Trace register accesses
drm/tegra: sor: Use unsigned int for register offsets
drm/tegra: hdmi: Use unsigned int for register offsets
drm/tegra: dsi: Use unsigned int for register offsets
drm/tegra: dpaux: Use unsigned int for register offsets
drm/tegra: dc: Use unsigned int for register offsets
drm/tegra: Fix NULL deref in debugfs/iova
drm/tegra: switch to drm_*_get(), drm_*_put() helpers
drm/tegra: Set MODULE_FIRMWARE for the VIC
drm/tegra: Add CONFIG_OF dependency
gpu: host1x: Support sub-devices recursively
gpu: host1x: fix error return code in host1x_probe()
gpu: host1x: Fix bitshift/mask multipliers
...
Register offsets are usually fairly small numbers, so an unsigned int is
more than enough to represent them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
The MIPI DSI output on Tegra SoCs requires some external logic to
calibrate the MIPI pads before a video signal can be transmitted. This
MIPI calibration logic requires to be powered on while the MIPI pads are
being used, which is currently done as part of the DSI driver's probe
implementation.
This is suboptimal because it will leave the MIPI calibration logic
powered up even if the DSI output is never used.
On Tegra114 and earlier this behaviour also causes the driver to hang
while trying to power up the MIPI calibration logic because the power
partition that contains the MIPI calibration logic will be powered on
by the display controller at output pipeline configuration time. Thus
the power up sequence for the MIPI calibration logic happens before
it's power partition is guaranteed to be enabled.
Fix this by splitting up the API into a request/free pair of functions
that manage the runtime dependency between the DSI and the calibration
modules (no registers are accessed) and a set of enable, calibrate and
disable functions that program the MIPI calibration logic at points in
time where the power partition is really enabled.
While at it, make sure that the runtime power management also works in
ganged mode, which is currently also broken.
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Tested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).
Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.
Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7xlG
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.8-rc1
This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).
Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.
Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.
* tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux: (35 commits)
drm/tegra: sor: Reject HDMI 2.0 modes
drm/tegra: sor: Prepare for generic PM domain support
drm/tegra: dsi: Prepare for generic PM domain support
drm/tegra: sor: Make XBAR configurable per SoC
drm/tegra: sor: Use sor1_src clock to set parent for HDMI
dt-bindings: display: tegra: Add source clock for SOR
drm/tegra: sor: Implement sor1_brick clock
drm/tegra: sor: Implement runtime PM
drm/tegra: hdmi: Implement runtime PM
drm/tegra: dsi: Implement runtime PM
drm/tegra: dc: Implement runtime PM
drm/tegra: hdmi: Enable audio over HDMI
drm/tegra: sor: Do not support deep color modes
drm/tegra: sor: Extract tegra_sor_mode_set()
drm/tegra: sor: Split out tegra_sor_apply_config()
drm/tegra: sor: Rename tegra_sor_calc_config()
drm/tegra: sor: Factor out tegra_sor_set_parent_clock()
drm/tegra: dpaux: Add pinctrl support
dt-bindings: Add bindings for Tegra DPAUX pinctrl driver
drm/tegra: Prepare DPAUX for supporting generic PM domains
...
The DSI driver for Tegra requires the SOR power partition to be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework. However, the sequence for
gating/ungating the SOR power partition requires that the DSI reset is
asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the DSI
driver cannot request the same reset unless we mark the reset as shared.
Sharing resets will not work in this case because we cannot guarantee
that the reset will be asserted/de-asserted at the appropriate time.
Therefore, given that the Tegra generic PM domain code will handle the
resets, do not request the reset in the DSI driver if the DSI device has
a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use runtime PM to clock-(un)gate, (de)assert reset and control power to
the DSI controller. This ties in nicely with atomic DPMS in that a
runtime PM reference is taken before a pipe is enabled and dropped after
it has been shut down.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All outputs have a 1:1 relationship between connectors and encoders
and the driver is relying on the atomic helpers: we can drop the custom
->best_encoder() implementation and let the core call
drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-14-git-send-email-boris.brezillon@free-electrons.com
Commit d2307dea14 ("drm/atomic: use connector references (v3)") added
reference counting for DRM connectors and this caused a crash when
exercising system suspend on Tegra114 Dalmore.
The Tegra DSI driver implements a Tegra specific function,
tegra_dsi_connector_duplicate_state(), to duplicate the connector state
and destroys the state using the generic helper function,
drm_atomic_helper_connector_destroy_state(). Following commit
d2307dea14 ("drm/atomic: use connector references (v3)") there is
now an imbalance in the connector reference count because the Tegra
function to duplicate state does not take a reference when duplicating
the state information. However, the generic helper function to destroy
the state information assumes a reference has been taken and during
system suspend, when the connector state is destroyed, this leads to a
crash because we attempt to put the reference for an object that has
already been freed.
Fix this by calling __drm_atomic_helper_connector_duplicate_state() from
tegra_dsi_connector_duplicate_state() to ensure that we take a reference
on a connector if crtc is set. Note that this will also copy the
connector state a 2nd time, but this should be harmless.
By fixing tegra_dsi_connector_duplicate_state() to take a reference,
although a crash was no longer seen, it was then observed that after
each system suspend-resume cycle, the reference would be one greater
than before the suspend-resume cycle. Following commit d2307dea14
("drm/atomic: use connector references (v3)"), it was found that we
also need to put the reference when calling the function
tegra_dsi_connector_reset() before freeing the state. Fix this by
updating tegra_dsi_connector_reset() to call the function
__drm_atomic_helper_connector_destroy_state() in order to put the
reference for the connector.
Fixes: d2307dea14 ("drm/atomic: use connector references (v3)")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463585856-16606-1-git-send-email-jonathanh@nvidia.com
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra132 to Tegra210, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra124 to Tegra132, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra114 to Tegra124, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In video modes without sync pulses, the horizontal back-porch needs to
include the horizontal sync width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously output drivers would enable continuous display mode and power
up the display controller at various points during the initialization.
This is suboptimal because it accesses display controller registers in
output drivers and duplicates a bit of code.
Move this code into the display controller driver and enable the display
controller as the final step of the ->mode_set_nofb() implementation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All output drivers have now been converted to use the ->atomic_check()
callback, so the ->mode_fixup() callbacks are no longer used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The implementation of the ->atomic_check() callback precomputes all
parameters to check if the given configuration can be applied. If so the
precomputed values are stored in the atomic state object for the encoder
and applied during modeset. In that way the modeset no longer needs to
perform any checking but simply program values into registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook up the default ->reset() and ->atomic_duplicate_state() helpers.
This ensures that state objects are properly created and framebuffer
reference counts correctly maintained.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement initial atomic state handling. Hook up the CRTCs, planes' and
connectors' ->atomic_destroy_state() callback to ensure that the atomic
state objects don't leak.
Furthermore the CRTC now implements the ->mode_set_nofb() callback that
is used by new helpers to implement ->mode_set() and ->mode_set_base().
These new helpers also make use of the new plane helper functions which
the driver now provides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_output midlayer is now completely gone and output drivers use
it purely as a helper library.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The debugfs cleanup code never fails, so no error is returned. Therefore
the functions can all return void instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement encoder and connector within the DSI driver itself using the
Tegra output helpers rather than using the Tegra output as midlayer. By
doing so one level of indirection is removed and output drivers become
more flexible while keeping the majority of the advantages provided by
the common output helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously output drivers would all stop the display controller in their
disable path. However with the transition to atomic modesetting the
display controller needs to be kept running until all planes have been
disabled so that software can properly determine (using VBLANK counts)
when it is safe to remove the framebuffers associated with the planes.
Moving this code into the display controller's disable path also gets
rid of the duplication of this into all output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All output drivers have open-coded variants of this function, so export
it to remove some code duplication.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows a DRM driver unload/reload cycle to completely reset the DSI
controller and may help in situations where it's broken.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DSI registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make sure the DSI PHY_TIMING and BTA_TIMING registers are initialized
when the clocks are set up as opposed to when the output is enabled.
This makes sure that the PHY timings are properly set up when the panel
is prepared and that DCS commands sent at that time use the appropriate
timings.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for sending MIPI DSI command packets from the host to a
peripheral. This is required for panels that need configuration before
they accept video data.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement ganged mode support for the Tegra DSI driver. The DSI host
controller to gang up with is specified via a phandle in the device tree
and the resolved DSI host controller used for the programming of the
ganged-mode registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for adding ganged-mode support, this commit splits out
the tegra_dsi_set_timeout() function so that it can be reused for the
slave DSI controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sowjanya Komatineni