Another case where we parsed vbios data to some structs, then again use
that info once to construct another set of data. Skip the intermediate
step.
This is also slightly improved in that we can now use DCB 3.x connector
table info, which will allow NV4x to gain hotplug support, and to make
quirks for SPWG LVDS panels unnecessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
i2c-algo-bit doesn't actually work very well on one card I have access to
(NVS 300), random single-bit errors occur most of the time - what we're
doing now is closer to what xf86i2c.c does.
The original plan was to figure out why i2c-algo-bit fails on the NVS 300,
and fix it. However, while investigating I discovered i2c-algo-bit calls
cond_resched(), which makes it a bad idea for us to be using as we execute
VBIOS scripts from a tasklet, and there may very well be i2c transfers as
a result.
So, since I already wrote this code in userspace to track down the NVS 300
bug, and it's not really much code - lets use it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Was using nv_mask, which is bad. Reading the reg senses the current line
states, which aren't necessarily the states we're trying to drive the
lines to.
Fixed to store SCL driver state just as we already do for SDA.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not much point parsing the vbios data into a struct which is only used once
to parse the data into another struct, go directly from vbios to
nouveau_i2c_chan.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This primary reason for this was mostly to avoid duplication of some of
this stuff by the MXM-SIS parser. However, some other cleanups will also
follow this as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Spotted while messing with overlay channels (probably as a result of
sending a similar "disable" sequence as we do for the flip channels).
The value in 0x61008c was 0x20, which one would reasonably guess is
"bit 5 == something to report about evo channel 5" - but who knows.
Spotted the binary driver getting this too, and it appears to not do
anything exciting as a result. So, handle it the same way and avoid
an IRQ storm.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pre-nva3 will likely require far more extensive setup, and nvd9 needs to
be checked to find its SOR_HDMI/SOR_AUDIO blocks.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
read_pll_ref() needs to take into account the refclk src bits in 0xc040 on
some chipsets, it wasn't doing this.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This area is horrifically complicated on these chipsets, and it's likely we
will need at least a few more tweaks yet.
Oh yes, and it's completely disabled on IGPs for the moment. From traces,
things look potentially different there yet again. Sigh...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Following to "drm/nv50/pm: s/unk05/vdec/", let's rename the PLL to PLL_VDEC
PLL names are purely indicative and are based on the most important engine
it clocks.
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reporting an error is better than silently refusing to reclock.
V2: Use the same logic on nv40
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes a case where we don't get separate supervisor interrupt sequences for
disconnect and modeset events.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should fix issues with kexec, and as a nice side bonus, the code to avoid
having PDISP disappear will also fix hibernate on those effected systems.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This has the effect of ensuring the encoders which were active before we
loaded get disconnected properly before we start reprogramming them.
Also removing a bit of cargo-cult from the initial evo pushbuf.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
PDISP doesn't like it when disabled CRTCs are poked.
Fixes external output not coming to life when it has cursor on.
https://bugs.freedesktop.org/show_bug.cgi?id=41608
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Otherwice code that responsible for idling the card can't work.
BIOS init tables are supposed to init the clocks to correct values,
so that shouldn't cause any problems (we don't reclock by default anyway)
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Because doing polling while hardware is disabled is a bad idea...
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Exposes the same connector properties as the Radeon implementation, however
their behaviour isn't exactly the same. The primary difference being that
unless both hborder/vborder have been defined by the user, the driver will
keep the aspect ratio of the overscanned area the same as the mode the
display is programmed for.
Enabled for digital outputs on GeForce 8 and up, excluding GF119.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A NV49 appeared a while back that was using the "nv41 style" pwm registers,
rather than the "nv40 style" ones my board is using. This disproves the
previous theory that the pwm controller choice is chipset-specific.
So, after looking at a bunch of vbios images it appears that the next viable
theory is that we should select the pwm controller to use based on the gpio
line the fan is tied to, just like we do on nv50.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The handling of the internal pwm fan controller is similar enough between
current chipsets that it makes sense to share the logic, and bugfixes :)
No hw backends converted yet, will automatically fall-through to the
"old" per-chipset fanspeed hooks for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Exposes the following sysfs entries:
- fan0_input: read the rotational speed of the fan (poll a bit during 250ms)
- pwm0: set the pwm duty cycle
- pwm0_min/max: set the minimum/maximum pwm value
v2 (Ben Skeggs):
- nv50 pwm controller code removed in favour of other more complete code
- FAN_RPM -> FAN_SENSE
- merged FAN_SENSE readout into common code, not at all nv50-specific
- protected fanspeed changes with perflvl_wr
- formatting tidying
- added some comments where things are shaky
v3 (Martin Peres)
- ensure duty min/max from thermal table are sane
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
The exynos fimd supports 5 window overlays. Only one window overlay of
fimd is used by the crtc, so we need plane feature to use the rest
window overlays.
This creates one ioctl exynos specific - DRM_EXYNOS_PLANE_SET_ZPOS, it
is the ioctl to decide for user to assign which window overlay.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This adds runtime PM feature for fimd. The runtime PM functions control
clocks for fimd and prevent to access the register of fimd for vblank
when clock is turned off by suspend of runtime PM.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
With DPMS ON and OFF requests, crtc dpms would be in charge of
just only device power such as fimd or hdmi and encoder dpms
in charge of device setting(mode setting and register updating)
and also lcd panel and digital TV power.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The exynos drm also should use struct drm_mode_fb_cmd2 by changes of
308e5bcbdb commit(drm: add an fb creation
ioctl that takes a pixel format v5).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This compile errors occur by changes of
e08e96de98 commit, so exynos drm should
apply this changes.
CC drivers/gpu/drm/exynos/exynos_drm_drv.o
drivers/gpu/drm/exynos/exynos_drm_drv.c:185: warning: braces around scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:185: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: warning: initialization from incompatible pointer type
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: warning: (near initialization for 'exynos_drm_driver.fops')
make[4]: *** [drivers/gpu/drm/exynos/exynos_drm_drv.o] Error 1
make[3]: *** [drivers/gpu/drm/exynos] Error 2
make[2]: *** [drivers/gpu/drm] Error 2
make[1]: *** [drivers/gpu] Error 2
make: *** [drivers] Error 2
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This function returns the number of planes used by a specific pixel
format.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Call connector->funcs->dpms(DPMS_ON) rather than just setting
connector->dpms = DPMS_ON. This ensures that if the connector
has something to do to enable the output (rather than just using
drm_helper_connector_dpms helper directly), that this happens
at bootup. This solves an issue with connectors not getting
enabled from fbcon_init() when the driver is loaded.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the bpc is set from the connector is 0, we then use it later to adjust
in a special case the HDMI pixel clock, however if the bpc is 0, we end up
passing a 0 pixel clock into the code.
I'm not sure if this is the correct answer or if we should avoid the HDMI
clock adjustment for 0 values.
This fixes a divide by 0 on my Llano system with a HDMI monitor and hdmi
audio enabled.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Somewhat specializaed sub-allocator designed to perform sub-allocation
for command buffer not only for current cs ioctl but for future command
submission ioctl as well. Patch also convert current ib pool to use
the sub allocator. Idea is that ib poll buffer can be share with other
command buffer submission not having 64K granularity.
v2 Harmonize pool handling and add suspend/resume callback to pin/unpin
sa bo (tested on rv280, rv370, r420, rv515, rv610, rv710, redwood, cayman,
rs480, rs690, rs880)
v3 Simplify allocator
v4 Fix radeon_ib_get error path to properly free fence
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
cayman is wb only and doesn't have a VC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some rptr/wptrs fields have different offsets and not all rings are pm4
so add a new nop field.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also test multiple waits on the same semaphore.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a start fence driver helper function which will be call
once for each ring and will compute cpu/gpu addr for fence
depending on wether to use wb buffer or scratch reg.
This patch replace initialize fence driver separately which
was broken in regard of GPU lockup. The fence list for created,
emited, signaled must be initialize once and only from the
asic init callback not from the startup call back which is
call from the gpu reset.
v2: With this in place we no longer need to know the number of
rings in fence_driver_init, also writing to the scratch reg
before knowing its offset is a bad idea.
v3: rebase on top of change to previous patch in the serie
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Those debugfs files aren't r600 specific, so they
shouldn't be in r600.c. Move them to radeon_ring.c
and also add functionality to dump CP1 & CP2 ring
informations.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
That naming seems to make more sense, since we not
only want to run PM4 rings with it.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Disable the additional compute rings on cayman
until their setup is fully implemented.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Split counting of emited fences out of power
management into a seperate function.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Emitting fences, semaphores and ib works differently
on different ring, so its is easier to maintain
separate functions for each ring.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tests syncing between all rings by using
semaphores and fences.
v2: use radeon_testing as a bit flag rather than on/off switch
this allow to test for one thing at a time (bo_move or semaphore
test). It kind of break the usage if user wheren't using 1
for bo move test but as it's a test feature i believe it's ok.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace cp, cp1 and cp2 members with just an array
of radeon_cp structs.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Every ring seems to have the concept of read and
write pointers. Make the register offset variable
so we can use the functions for different types of rings.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Give all asic and radeon_ring_* functions a
radeon_cp parameter, so they know the ring to work with.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They are used to sync between rings, while fences
sync between a ring and the cpu.
v2 Fix radeon_semaphore_driver_fini when no semaphore were
allocated.
v3 Initialize list early on to avoid issue in case or early
error
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For supporting multiple CP ring buffers, async DMA
engines and UVD. We still need a way to synchronize
between engines.
v2 initialize unused fence driver ring to avoid issue in
suspend/unload
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Better fix it before this obvious typo spreads even more.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only check the previously checked relocs for
duplicates. Also leaving the handle uninitialized
isn't such a good idea.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Having registered debugfs files globally causes
the files to not show up on the second, third
etc.. card in the system.
v2: fix crash on module unloading
v3: fix space indentation
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GCT setup was used on Moorestown. The Oaktrail version uses a normal PC
interface. That means we must also honour the dither info from the BIOS
data.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The move to connectors breaks Oaktrail again if we have memory poisoning
enabled. Fix this.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge in the upstream tree to bring in the mainline fixes.
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/nouveau_sgdma.c
This switches the ifdef to match the Kconfig so that Oaktrail probing occurs
and adds some additional minor bulletproofing.
Tested on a Fujtisu Stylistic Q550 internal display. HDMI might work but that
remains to be seen.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We currently don't have support for parsing SDVO mappings from BIOS so we're
guessing the bus switch parameter. This isn't working so hardcode it to a
configuration known to work on most poulsbo hardware.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace psb_intel_output with psb_intel_encoder and psb_intel_connector
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
[Changed Moorestown reference to Oaktrail]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace psb_intel_output with psb_intel_encoder and psb_intel_connector.
Things will need to be cleaned up and tested so consider this an initial
patch for Cedarview.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Our current SDVO implementation is not working properly, so replace it with
a modified version of the i915. Further testing and debugging is needed to make
sure we can handle the different SDVO setups and wiring.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Before we integrate the new SDVO code we need GMBUS support
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
LVDS for PSB now uses psb_intel_encoder and psb_intel_connectors instead of
psb_intel_output. i2c_bus and ddc_bus are moved to lvds_priv. There was also a
pointer to mode_dev (for no obvious reason) that we now get directly from
dev_priv.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix cases where we need to know what encoder type is behind a given connector.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
First step towards adding i915 alike encoder and connector abstractions. This
will make life easier when adding i915 output code into our driver. It also
removes the old psb_intel_output struct.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise each driver would need to keep the information inside
their own framebuffer object structure. Also add offsets[]. BOs
on the other hand are driver specific, so those can be kept in
driver specific structures.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Help drivers a little by guaranteeing that crtc_x+crtc_w and
crtc_y+crtc_h don't overflow.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure the source coordinates stay within the buffer.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These are the only indication to user space that the plane was disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Several pointers and casts were missing __user annotations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unlock the mode_config mutex if drm_plane_init() fails.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My EFI BIOS starts the graphics card up in my projector's preferred EDID
mode, 1080@60i. The Intel driver does not clear all the interlaced bits.
This patch introduces a new PIPECONF_INTERLACE_MASK define and uses it
to restore progressive mode.
Signed-of-by: Christian Schmidt <schmidt@digadd.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current logic misunderstands the spec about CEA 18byte descriptors.
First, the spec doesn't state "detailed timing descriptors" but "18 byte
descriptors", so any data record could be stored, mixed timings and
other data, just as in the standard EDID.
Second, the lower four bit of byte 3 of the CEA record do not contain
the number of descriptors, but "the total number of DTDs defining native
formats in the whole EDID [...], starting with the first DTD in the DTD
list (which starts in the base EDID block)." A device can of course
support non-native formats.
As such the number can't be used to determine n, and the existing code
will filter non-timing 18byte descriptors anyway.
Signed-off-by: Christian Schmidt <schmidt@digadd.de>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
CEA datablocks are only defined from revision 3 onwards. Only check for
them if the revision says so.
Signed-of-by: Christian Schmidt <schmidt@digadd.de>
Tested-by: James Cloos <cloos@jhcloos.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise hangcheck spuriously fires when running blitter/bsd-only
workloads.
Contrary to a similar patch by Ben Widawsky this does not check
INSTDONE of the other rings. Chris Wilson implied that in a failure to
detect a hang, most likely because INSTDONE was fluctuating. Thus only
check ACTHD, which as far as I know is rather reliable. Also, blitter
and bsd rings can't launch complex tasks from a single instruction
(like 3D_PRIM on the render with complex or even infinite shaders).
This fixes spurious gpu hang detection when running
tests/gem_hangcheck_forcewake on snb/ivb.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
On DP monitor hot remove, clear DP_AUDIO_OUTPUT_ENABLE accordingly,
so that the audio driver will receive hot plug events and take action
to refresh its device state and ELD contents.
Note that the DP_AUDIO_OUTPUT_ENABLE bit may be enabled or disabled
only when the link training is complete and set to "Normal".
Tested OK for both hot plug/remove and DPMS on/off.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On HDMI monitor hot remove, clear SDVO_AUDIO_ENABLE accordingly, so that
the audio driver will receive hot plug events and take action to refresh
its device state and ELD contents.
The cleared SDVO_AUDIO_ENABLE bit needs to be restored to prevent losing
HDMI audio after DPMS on.
CC: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The ELD may or may not change when switching the video mode.
If unchanged, don't trigger hot plug events to HDMI audio driver.
This avoids disturbing the user with repeated printks.
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Change the definitions from GEN5 to IBX as they aren't in the CPU and
some SNB systems actually shipped with IBX chipsets (or, at least that's
a supported configuration).
The GEN7_* register addresses actually take effect since GEN6 and should
be prefixed by CPT, the PCH code name.
Suggested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
SandyBridge should be using the same register addresses as IvyBridge.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Doesn't protect any error code and only gets in the way of debugging.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The driver implements the needed resource management required
to use that register.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (22 commits)
[SCSI] fcoe: fix fcoe in a DCB environment by adding DCB notifiers to set skb priority
[SCSI] bnx2i: Fixed kernel panic caused by unprotected task->sc->request deref
[SCSI] qla4xxx: check for failed conn setup
[SCSI] qla4xxx: a small loop fix
[SCSI] qla4xxx: fix flash/ddb support
[SCSI] zfcp: return early from slave_destroy if slave_alloc returned early
[SCSI] fcoe: Fix preempt count leak in fcoe_filter_frames()
[SCSI] qla2xxx: Update version number to 8.03.07.12-k.
[SCSI] qla2xxx: Submit all chained IOCBs for passthrough commands on request queue 0.
[SCSI] qla2xxx: Correct fc_host port_state display.
[SCSI] qla2xxx: Disable generating pause frames when firmware hang detected for ISP82xx.
[SCSI] qla2xxx: Clear mailbox busy flag during premature mailbox completion for ISP82xx.
[SCSI] qla2xxx: Encapsulate prematurely completing mailbox commands during ISP82xx firmware hang.
[SCSI] qla2xxx: Display IPE error message for ISP82xx.
[SCSI] qla2xxx: Return the correct value for a mailbox command if 82xx is in reset recovery.
[SCSI] qla2xxx: Enable Minidump by default with default capture mask 0x1f.
[SCSI] qla2xxx: Stop unconditional completion of mailbox commands issued in interrupt mode during firmware hang.
[SCSI] qla2xxx: Revert back the request queue mapping to request queue 0.
[SCSI] qla2xxx: Don't call alloc_fw_dump for ISP82XX.
[SCSI] qla2xxx: Check for SCSI status on underruns.
...
* 'for-linus/i2c-32-rc6' of git://git.fluff.org/bjdooks/linux:
i2c-eg20t: correct the driver init order of pch_i2c_probe()
I2C: OMAP: fix FIFO usage for OMAP4
i2c-s3c2410: Fix return code of s3c24xx_i2c_parse_dt_gpio
i2c: i2c-s3c2410: Add a cpu_relax() to busy wait for bus idle
I noticed that hotplug of one setup does not work with recent change in
pci tree.
After checking the bridge conf setup, I noticed that the bridges get
assigned but do not get enabled.
The reason is the following commit, while simply ignores bridge
resources when enabling a pci device:
| commit bbef98ab0f
| Author: Ram Pai <linuxram@us.ibm.com>
| Date: Sun Nov 6 10:33:10 2011 +0800
|
| PCI: defer enablement of SRIOV BARS
|...
| NOTE: Note, there is subtle change in the pci_enable_device() API. Any
| driver that depends on SRIOV BARS to be enabled in pci_enable_device()
| can fail.
Put back bridge resource and ROM resource checking to fix the problem.
That should fix regression like BIOS does not assign correct resource to
bridge.
Discussion can be found at:
http://www.spinics.net/lists/linux-pci/msg12874.html
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before registering an adapter to i2c subsystem, we need make sure
driver is ready for incoming i2c xfer, becasue the i2c_add_adapter()
may trigger a i2c device driver's proble function which may start
some real i2c xfer. I met this issue when integrating a TSC2007 i2c
touch screen device with the i2c-eg20t driver.
This patch will call request_irq() and hw init before calling
i2c_add_adapter().
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Currently the fifo depth is set to zero for OMAP4 which disables
the FIFO usage. This patch enables the FIFO usage for I2C transactions
on OMAP4 also.
Tested on omap4430 and 3430.
Tested-and-Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
s3c24xx_i2c_parse_dt_gpio is called when cfg_gpio is not defined
in the platform data of the i2c device. When DT is not enabled,
the above function always returns -EINVAL. Since there can be
some i2c devices which don't need to configure any gpio lines,
the probe of such devices would fail here. Changing the default
return value to success would fix this issue.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Set device power state to PCI_D0 for device without native PM support
PCI hotplug: Always allow acpiphp to handle non-PCIe bridges
PCI: fix ats compile failure
PCI: defer enablement of SRIOV BARS
This reverts commit eb1711bb94.
It blows up the i915 seqno tracking, resulting in the
BUG_ON(seqno == 0);
in i915_wait_request() triggering, which will cause lock-ups.
See for example
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/903010https://lkml.org/lkml/2011/12/14/395
Reported-requested-and-tested-by: Dirk Hohndel <dirk@hohndel.org>
Reported-by: Richard Eames <Richard.Eames@flinders.edu.au>
Reported-by: Rocko Requin <rockorequin@hotmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32: Be less strict in matching %lo part of relocation.
sbus: convert drivers/sbus/char/* to use module_platform_driver()
bbc_i2c: Remove unneeded err variable
sparc: Use kmemdup rather than duplicating its implementation
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv6: Check dest prefix length on original route not copied one in rt6_alloc_cow().
sch_gred: should not use GFP_KERNEL while holding a spinlock
ipip, sit: copy parms.name after register_netdevice
ipv6: Fix for adding multicast route for loopback device automatically.
ssb: fix init regression with SoCs
rtl8192{ce,cu,de,se}: avoid problems because of possible ERFOFF -> ERFSLEEP transition
mac80211: fix another race in aggregation start
fsl_pq_mdio: Clean up tbi address configuration
ppp: fix pptp double release_sock in pptp_bind()
net/fec: fix the use of pdev->id
ath9k: fix check for antenna diversity support
batman-adv: delete global entry in case of roaming
batman-adv: in case of roaming mark the client with TT_CLIENT_ROAM
Bluetooth: Correct version check in hci_setup
btusb: fix a memory leak in btusb_send_frame()
Bluetooth: bnep: Fix module reference
Bluetooth: cmtp: Fix module reference
Bluetooth: btmrvl: support Marvell Bluetooth device SD8797
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux:
drm/i915/dp: Dither down to 6bpc if it makes the mode fit
drm/i915: enable semaphores on per-device defaults
drm/i915: don't set unpin_work if vblank_get fails
drm/i915: By default, enable RC6 on IVB and SNB when reasonable
iommu: Export intel_iommu_enabled to signal when iommu is in use
drm/i915/sdvo: Include LVDS panels for the IS_DIGITAL check
drm/i915: prevent division by zero when asking for chipset power
drm/i915: add PCH info to i915_capabilities
drm/i915: set the right SDVO transcoder for CPT
drm/i915: no-lvds quirk for ASUS AT5NM10T-I
drm/i915: Treat pre-gen4 backlight duty cycle value consistently
drm/i915: Hook up Ivybridge eDP
drm/i915: add multi-threaded forcewake support
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: Fix DA9052 GPIO build errors.
gpio: mpc8xxx: don't allow input-only pins to be output for MPC5121
gpio-ml-ioh: Add the irq_disable/irq_enable hooks for ml-ioh irq chip
gpio-ml-ioh: fix a bug in the interrupt handler
gpio: pl061: drop extra check for NULL platform_data
Some active adaptors (VGA usually) only have two lanes at 2.7GHz.
That's a maximum pixel clock of 144MHz at 8bpc, but 192MHz at 6bpc.
Fixes Asus UX31 panel being black at startup due to no valid modes since
dc22ee6fc1.
v2: Rebased to current code, resulting in the fix applying to EDP panels as
well. Also changed from spatio-temporal to just spatial dithering on
pre-ironlake, to be conssitent (and less visual flicker)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This adds a default setting for semaphores parameter, and enables
semaphores by default on IVB.
For now, as semaphores interaction with VTd causes random issues on
SNB, we do not enable them by default. But they can still be enabled
via the semaphores=1 kernel parameter.
v2: enables semaphores on SNB when IO remapping is disabled, with base
on Keith Packard patch.
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Ben Widawsky <ben@bwidawsk.net>
CC: Keith Packard <keithp@keithp.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42696
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=40564
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38862
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This fixes a race where we may try to finish a page flip and decrement
the refcount even if our vblank_get failed and we ended up with a
spurious flip pending interrupt.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=34211.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
RC6 should always work on IVB, and should work on SNB whenever IO
remapping is disabled. RC6 never works on Ironlake. Make the default
value for the parameter follow these guidelines. Setting the value
to either 0 or 1 will force the specified behavior.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38567
Cc: Ted Phelps <phelps@gnusto.com>
Cc: Peter <pab1612@gmail.com>
Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz>
Cc: Andrew Lutomirski <luto@mit.edu>
In i915 driver, we do not enable either rc6 or semaphores on SNB when dmar
is enabled. The new 'intel_iommu_enabled' variable signals when the
iommu code is in operation.
Cc: Ted Phelps <phelps@gnusto.com>
Cc: Peter <pab1612@gmail.com>
Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz>
Cc: Andrew Lutomirski <luto@mit.edu>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We were checking whether the supplied edid matched the connector it was
read from. We do this in case a DDC read returns an EDID for another
device on a multifunction or otherwise interesting card. However, we
failed to include LVDS as a digital device and so rejecting an otherwise
valid EDID.
Fixes the detection of the secondary SDVO LVDS panel on the Libretto
W105.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=39216
Signed-off-by: Keith Packard <keithp@keithp.com>
This prevents an in-kernel division by zero which happens when we are
asking for i915_chipset_val too quickly, or within a race condition
between the power monitoring thread and userspace accesses via debugfs.
The issue can be reproduced easily via the following command:
while ``; do cat /sys/kernel/debug/dri/0/i915_emon_status; done
This is particularly dangerous because it can be triggered by
a non-privileged user by just reading the debugfs entry.
This issue was also found independently by Konstantin Belousov
<kostikbel@gmail.com>, who proposed a similar patch.
Reported-by: Konstantin Belousov <kostikbel@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
v2: add a CPT-specific macro, make code cleaner
v3: fix commit message
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41272
Cc: stable@kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8712u: Add new USB ID
staging: tidspbridge: request dmtimer clocks on init
staging: tidspbridge: include module.h by default
* 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/swiotlb: Use page alignment for early buffer allocation.
xen: only limit memory map to maximum reservation for domain 0.
This patch is functionally tested on Samsung SMDKV6410.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[grant.likely: don't create an unnecessary header file]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes an odd bug found on a Dell PowerEdge 1850/0RC130
(BIOS A05 01/09/2006) where all of the modules doing pci_set_dma_mask
would fail with:
ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
ata_piix 0000:00:1f.1: can't derive routing for PCI INT A
ata_piix 0000:00:1f.1: BMDMA: failed to set dma mask, falling back to PIO
The issue was the Xen-SWIOTLB was allocated such as that the end of
buffer was stradling a page (and also above 4GB). The fix was
spotted by Kalev Leonid which was to piggyback on git commit
e79f86b2ef "swiotlb: Use page alignment
for early buffer allocation" which:
We could call free_bootmem_late() if swiotlb is not used, and
it will shrink to page alignment.
So alloc them with page alignment at first, to avoid lose two pages
And doing that fixes the outstanding issue.
CC: stable@kernel.org
Suggested-by: "Kalev, Leonid" <Leonid.Kalev@ca.com>
Reported-and-Tested-by: "Taylor, Neal E" <Neal.Taylor@ca.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Use DCB notifiers to set the skb priority to allow packets
to be steered and tagged correctly over DCB enabled drivers
that setup traffic classes.
This allows queue_mapping() routines to be removed in these
drivers that were previously inspecting the ethertype of
every skb to mark FCoE/FIP frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During test of one IB card with guest VM, found that, msi is not
initialized properly.
It turns out __write_msi_msg will do nothing if device current_state is
not PCI_D0. And, that pci device does not have pm_cap in guest VM.
There is an error in setting of power state to PCI_D0 in
pci_enable_device(), but error is not returned for this. Following is
code flow:
pci_enable_device() --> __pci_enable_device_flags() -->
do_pci_enable_device() --> pci_set_power_state() -->
__pci_start_power_transition()
We have following condition inside __pci_start_power_transition():
if (platform_pci_power_manageable(dev)) {
error = platform_pci_set_power_state(dev, state);
if (!error)
pci_update_current_state(dev, state);
} else {
error = -ENODEV;
/* Fall back to PCI_D0 if native PM is not supported */
if (!dev->pm_cap)
dev->current_state = PCI_D0;
}
Here, from platform_pci_set_power_state(), acpi_pci_set_power_state() is
getting called and that is failing with ENODEV because of following
condition:
if (!handle || ACPI_SUCCESS(acpi_get_handle(handle, "_EJ0",&tmp)))
return -ENODEV;
Because of that, pci_update_current_state() is not getting called.
With this patch, if device power state can not be set via
platform_pci_set_power_state and that device does not have native pm
support, then PCI device power state will be set to PCI_D0.
-v2: This also reverts 47e9037ac1, as it's
not needed after this change.
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ajaykumar Hotchandani<ajaykumar.hotchandani@oracle.com>
Signed-off-by: Yinghai Lu<yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During session recovery, the conn_stop call will trigger a flush
to all outstanding SCSI cmds in the xmit queue. This will set
all outstanding task->sc to NULL prior to the session_teardown
call which frees the task memory.
In the bnx2i SCSI response processing path, only the task was being checked
for NULL under the session lock before the task->sc->request dereferencing.
If there are outstanding SCSI cmd responses pending for process, the
following kernel panic can be exposed where task->sc was found to be NULL.
Call Trace:
[ 69.720205] [<ffffffffa040d0d0>] bnx2i_process_new_cqes+0x290/0x3c0 [bnx2i]
[ 69.804289] [<ffffffffa040d233>] bnx2i_fastpath_notification+0x33/0xa0 [bnx2
i]
[ 69.891490] [<ffffffffa040d37b>] bnx2i_indicate_kcqe+0xdb/0x330 [bnx2i]
[ 69.971427] [<ffffffffa03eac5e>] service_kcqes+0x16e/0x1d0 [cnic]
[ 70.045132] [<ffffffffa03eacea>] cnic_service_bnx2x_kcq+0x2a/0x50 [cnic]
[ 70.126105] [<ffffffffa03ead53>] cnic_service_bnx2x_bh+0x43/0x140 [cnic]
[ 70.207081] [<ffffffff81060676>] tasklet_action+0x66/0x110
[ 70.273521] [<ffffffff8106025f>] __do_softirq+0xef/0x220
[ 70.337887] [<ffffffff81447ebc>] call_softirq+0x1c/0x30
This patch adds the !task->sc check and also protects the sc dereferencing
under the session lock.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
iscsi_conn_setup can fail so we must check for NULL being
returned.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the qla4xxx_get_fwddb_entry returns QLA_ERROR
the nex_idx is not updated,
for (idx = 0; idx < max_ddbs; idx = next_idx) {
ret = qla4xxx_get_fwddb_entry(ha, idx, NULL, 0, NULL,
&next_idx, &state, &conn_err,
NULL, NULL);
if (ret == QLA_ERROR)
continue;
This means there is a risk that the 'idx < max_ddbs' condition will never
met and the loop will loop forever.
Fix this by explicitly increasing the next_idx in the error condition.
Maybe a break instead of continue is more appropriate, leaving the decision
on the qlogic maintainer.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With open-iscsi support, target entries persisted in the FLASH were not
login. Added support in the qla4xxx driver to do the login on probe
time to the target entries saved in the FLASH by user.
With this changes upgrade to the new kernel with open-iscsi support in
qla4xxx will ensure users original target entries login on driver load
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
zfcp_scsi_slave_destroy erroneously always tried to finish its task
even if the corresponding previous zfcp_scsi_slave_alloc returned
early. This can lead to kernel page faults on accessing uninitialized
fields of struct zfcp_scsi_dev in zfcp_erp_lun_shutdown_wait. Take the
port field of the struct to determine if slave_alloc returned early.
This zfcp bug is exposed by 4e6c82b (in turn fixing f7c9c6b to be
compatible with 21208ae) which can call slave_destroy for a
corresponding previous slave_alloc that did not finish.
This patch is based on James Bottomley's fix suggestion in
http://www.spinics.net/lists/linux-scsi/msg55449.html.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Cc: <stable@kernel.org> #2.6.38+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The error exit path leaks preempt count. Add the missing put_cpu().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add USB ID for Sitecom WLA-2000 v1.001 WLAN.
Reported-and-tested-by: Roland Gruber <post@rolandgruber.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given that dm timer framework doesn't support request of clocks
by soft | hard irqs because some recent changes, tidspbridge needs
to request its clocks on init and enable/disable them on demand.
This was first seen on 3.2-rc1.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes compilation break when compiled as part of the kernel:
drivers/staging/tidspbridge/rmgr/drv_interface.c:134: error: expected declaration specifiers or '...' before string constant
drivers/staging/tidspbridge/rmgr/drv_interface.c:134: warning: data definition has no type or storage class
drivers/staging/tidspbridge/rmgr/drv_interface.c:134: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/staging/tidspbridge/rmgr/drv_interface.c:134: warning: function declaration isn't a prototype
drivers/staging/tidspbridge/rmgr/drv_interface.c:135: error: expected declaration specifiers or '...' before string constant
drivers/staging/tidspbridge/rmgr/drv_interface.c:135: warning: data definition has no type or storage class
drivers/staging/tidspbridge/rmgr/drv_interface.c:135: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/staging/tidspbridge/rmgr/drv_interface.c:135: warning: function declaration isn't a prototype
drivers/staging/tidspbridge/rmgr/drv_interface.c:136: error: expected declaration specifiers or '...' before string constant
drivers/staging/tidspbridge/rmgr/drv_interface.c:136: warning: data definition has no type or storage class
drivers/staging/tidspbridge/rmgr/drv_interface.c:136: warning: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/staging/tidspbridge/rmgr/drv_interface.c:136: warning: function declaration isn't a prototype
drivers/staging/tidspbridge/rmgr/drv_interface.c: In function 'omap34_xx_bridge_probe':
drivers/staging/tidspbridge/rmgr/drv_interface.c:359: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/staging/tidspbridge/rmgr/drv_interface.c:359: error: (Each undeclared identifier is reported only once
drivers/staging/tidspbridge/rmgr/drv_interface.c:359: error: for each function it appears in.)
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: add missing spin_unlock at ceph_mdsc_build_path()
ceph: fix SEEK_CUR, SEEK_SET regression
crush: fix mapping calculation when force argument doesn't exist
ceph: use i_ceph_lock instead of i_lock
rbd: remove buggy rollback functionality
rbd: return an error when an invalid header is read
ceph: fix rasize reporting by ceph_show_options
Ben Skeggs