This patch removes dbgname member from sysmmu_drvdata structure.
Kernel message for debugging already has the name of a single
System MMU node. It also removes some compilation warnings.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Checking if the probing device has a parent device was just to discover
if the probing device is involved in a power domain when the power
domain controlled by Samsung's custom implementation.
Since generic IO power domain is applied, it is required to remove
the condition to see if the probing device has a parent device.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This commit adds cache flush for removed small and large page entries
in exynos_iommu_unmap(). Missing cache flush of removed page table
entries can cause missing page fault interrupt when a master IP
accesses an unmapped area.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Prefetch buffer is a cache of System MMU 3.x and caches a block of
page table entries to make effect of larger page with small pages.
However, how to control prefetch buffers and the specifications of
prefetch buffers different from minor versions of System MMU v3.
Prefetch buffers must be controled with care because there are some
restrictions in H/W design.
The interface and implementation to initiate prefetch buffers will
be prepared later.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
L2TLB is 8-way set-associative TLB with 512 entries. The number of
sets is 64.
A single 4KB(small page) translation information is cached
only to a set whose index is the same with the lower 6 bits of the page
frame number.
A single 64KB(large page) translation information can be
cached to any 16 sets whose top two bits of their indices are the same
with the bit [5:4] of the page frame number.
A single 1MB(section) or larger translation information can be cached to
any set in the TLB.
It is required to invalidate entire sets that may cache the target
translation information to guarantee that the L2TLB has no stale data.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since kmalloc() does not guarantee that the allignment of 1KiB when it
allocates 1KiB, it is required to allocate lv2 page table from own
slab that guarantees alignment of 1KiB
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch changes not to panic on any error when updating page table.
Instead prints error messages with callstack.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Commit 25e9d28d92 (ARM: EXYNOS: remove system mmu initialization from
exynos tree) removed arch/arm/mach-exynos/mach/sysmmu.h header without
removing remaining use of it from exynos-iommu driver, thus causing a
compilation error.
This patch fixes the error by removing respective include line
from exynos-iommu.c.
Use of __pa and __va macro is changed to virt_to_phys and phys_to_virt
which are recommended in driver code. printk formatting of physical
address is also fixed to %pa.
Also System MMU driver is changed to control only a single instance
of System MMU at a time. Since a single instance of System MMU has only
a single clock descriptor for its clock gating, single address range
for control registers, there is no need to obtain two or more clock
descriptors and ioremaped region.
CC: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
set_device_exclusion_range(u16 devid, struct ivmd_header *m) enables
exclusion range for ONE device. IOMMU does not translate the access
to the exclusion range from the device.
The device is specified by input argument 'devid'. But 'devid' is not
passed to the actual set function set_dev_entry_bit(), instead
'm->devid' is passed. 'm->devid' does not specify the exact device
which needs enable the exclusion range. 'm->devid' represents DeviceID
field of IVMD, which has different meaning depends on IVMD type.
The caller init_exclusion_range() sets 'devid' for ONE device. When
m->type is equal to ACPI_IVMD_TYPE_ALL or ACPI_IVMD_TYPE_RANGE,
'm->devid' is not equal to 'devid'.
This patch fixes 'm->devid' to 'devid'.
Signed-off-by: Su Friendy <friendy.su@sony.com.cn>
Signed-off-by: Tamori Masahiro <Masahiro.Tamori@jp.sony.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
get_user_pages requires caller to hold a read lock on mmap_sem.
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
An apparent cut and paste error prevents the correct flags from being
set on the alias device resulting in MSI on conventional PCI devices
failing to work. This also produces error events from the IOMMU like:
AMD-Vi: Event logged [INVALID_DEVICE_REQUEST device=00:14.4 address=0x000000fdf8000000 flags=0x0a00]
Where 14.4 is a PCIe-to-PCI bridge with a device behind it trying to
use MSI interrupts.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
There is already S2CR_TYPE_SHIFT in S2CR_TYPE_TRANS macro, so drop the
second shift. Note that, since S2CR_TYPE_SHIFT is 0x0, there is no
functional change introduced by this patch.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The output size of stage-1 is currently limited by the input size of
stage-2, which is further limited by VA_BITS since we make use of the
standard pgd_alloc functions for creating page tables.
This patch ensures that we use VA_BITS instead of a hardcoded '39'
for the stage-1 output size limit.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Replace the devm_ioremap_nocache() call with devm_ioremap_resource().
This simplifies error checking.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The prot flags passed to the IOMMU map handler are defined in
include/linux/iommu.h as IOMMU_(READ|WRITE|CACHE|EXEC). However, the
driver expects to receive MMU_RAM_* OMAP-specific flags. This causes
IOMMU flags being interpreted as page sizes, leading to failures.
Hardcode the OMAP mapping parameters to little-endian, 8-bits and
non-mixed page attributes. Furthermore, as the OMAP IOMMU doesn't
support read-only or write-only mappings, ignore the prot value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Suman Anna <s-anna@ti.com>
The IOMMU core breaks out mappings into pages already, there's no
need to support mapping multiple pages in one go.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
The flush_iotlb_page() function prints a debug message when no
corresponding page was found in the TLB. That condition is incorrectly
checked and always resolves to true, given that the for_each_iotlb_cr()
loop is never interrupted and always reaches obj->nr_tlb_entries.
Given that we can't have two TLB entries for the same VA, break from the
loop when a match is found.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Suman Anna <s-anna@ti.com>
The to_iommu definition is used only locally to the omap-iommu.c
source file, and it has nothing to do with the page attributes
defined in omap-iopgtable.h. So, move the definition out of
omap-iopgtable.h header file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The current OMAP IOMMU ops for .domain_has_cap is a stub,
and the iommu core already returns a value of 0 if the
domain doesn't have a .domain_has_cap ops plugged in. So,
clean up this stub function.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The iotlb_entry field values are used directly in omap2_alloc_cr,
a function used in preparing the MMU_CAM and MMU_RAM registers.
The iotlb_entry.valid value is being set incorrectly to 1 at the
moment, and this would result in overriding the PAGESIZE bit field
of the MMU_CAM register if prefetching of the entries were to be
supported.
The bug has not caused any MMU faults due to incorrect size
programming so far as the prefetching is disabled by default. Fix
this by using the correct init value for the iotlb_entry.valid
field.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
kernel panic happened when iommu_unmap a buffer larger than 2MB,
more than expected pmd entries got “invalidated”, due to a wrong range
passed to arm_smmu_alloc_init_pte. it was likely a typo, now we fix
it, passing the correct "end" address to arm_smmu_alloc_init_pte.
Signed-off-by: Bin Wang <binw@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The IOMMU core expects the unmap operation to return the number of bytes
that have been unmapped or 0 on failure, a negative return value being
treated like a number of bytes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit "59ce0515cdaf iommu/vt-d: Update DRHD/RMRR/ATSR device scope
caches when PCI hotplug happens" introduces a bug, which fails to
match PCI devices with DMAR device scope entries if PCI path array
in the entry has more than one level.
For example, it fails to handle
[1D2h 0466 1] Device Scope Entry Type : 01
[1D3h 0467 1] Entry Length : 0A
[1D4h 0468 2] Reserved : 0000
[1D6h 0470 1] Enumeration ID : 00
[1D7h 0471 1] PCI Bus Number : 00
[1D8h 0472 2] PCI Path : 1C,04
[1DAh 0474 2] PCI Path : 00,02
And cause DMA failure on HP DL980 as:
DMAR:[fault reason 02] Present bit in context entry is clear
dmar: DRHD: handling fault status reg 602
dmar: DMAR:[DMA Read] Request device [02:00.2] fault addr 7f61e000
Reported-and-tested-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 146922ec79 ("iommu/vt-d: Make get_domain_for_dev() take struct
device") introduced new variables bridge_bus and bridge_devfn to
identify the upstream PCIe to PCI bridge responsible for the given
target device. Leaving the original bus/devfn variables to identify
the target device itself, now that it is no longer assumed to be PCI
and we can no longer trivially find that information.
However, the patch failed to correctly use the new variables in all
cases; instead using the as-yet-uninitialised 'bus' and 'devfn'
variables.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit ea8ea46 "iommu/vt-d: Clean up and fix page table clear/free
behaviour" introduces possible leakage of DMA page tables due to:
for (pte = page_address(pg); !first_pte_in_page(pte); pte++) {
if (dma_pte_present(pte) && !dma_pte_superpage(pte))
freelist = dma_pte_list_pagetables(domain, level - 1,
pte, freelist);
}
For the first pte in a page, first_pte_in_page(pte) will always be true,
thus dma_pte_list_pagetables() will never be called and leak DMA page
tables if level is bigger than 1.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This time a few more updates queued up.
* Rework VT-d code to support ACPI devices
* Improvements for memory and PCI hotplug support
in the VT-d driver
* Device-tree support for OMAP IOMMU
* Convert OMAP IOMMU to use devm_* interfaces
* Fixed PASID support for AMD IOMMU
* Other random cleanups and fixes for OMAP, ARM-SMMU
and SHMOBILE IOMMU
Most of the changes are in the VT-d driver because some rework was
necessary for better hotplug and ACPI device support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uy/Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU upates from Joerg Roedel:
"This time a few more updates queued up.
- Rework VT-d code to support ACPI devices
- Improvements for memory and PCI hotplug support in the VT-d driver
- Device-tree support for OMAP IOMMU
- Convert OMAP IOMMU to use devm_* interfaces
- Fixed PASID support for AMD IOMMU
- Other random cleanups and fixes for OMAP, ARM-SMMU and SHMOBILE
IOMMU
Most of the changes are in the VT-d driver because some rework was
necessary for better hotplug and ACPI device support"
* tag 'iommu-updates-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (75 commits)
iommu/vt-d: Fix error handling in ANDD processing
iommu/vt-d: returning free pointer in get_domain_for_dev()
iommu/vt-d: Only call dmar_acpi_dev_scope_init() if DRHD units present
iommu/vt-d: Check for NULL pointer in dmar_acpi_dev_scope_init()
iommu/amd: Fix logic to determine and checking max PASID
iommu/vt-d: Include ACPI devices in iommu=pt
iommu/vt-d: Finally enable translation for non-PCI devices
iommu/vt-d: Remove to_pci_dev() in intel_map_page()
iommu/vt-d: Remove pdev from intel_iommu_attach_device()
iommu/vt-d: Remove pdev from iommu_no_mapping()
iommu/vt-d: Make domain_add_dev_info() take struct device
iommu/vt-d: Make domain_remove_one_dev_info() take struct device
iommu/vt-d: Rename 'hwdev' variables to 'dev' now that that's the norm
iommu/vt-d: Remove some pointless to_pci_dev() calls
iommu/vt-d: Make get_valid_domain_for_dev() take struct device
iommu/vt-d: Make iommu_should_identity_map() take struct device
iommu/vt-d: Handle RMRRs for non-PCI devices
iommu/vt-d: Make get_domain_for_dev() take struct device
iommu/vt-d: Make domain_context_mapp{ed,ing}() take struct device
iommu/vt-d: Make device_to_iommu() cope with non-PCI devices
...
Pull DMA-mapping updates from Marek Szyprowski:
"This contains extension for more efficient handling of io address
space for dma-mapping subsystem for ARM architecture"
* 'for-3.15' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: dma-mapping: remove order parameter from arm_iommu_create_mapping()
arm: dma-mapping: Add support to extend DMA IOMMU mappings
Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3mNS
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)"
* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
...
Conflicts:
arch/x86/include/asm/topology.h
drivers/ata/ahci.c
If we failed to find an ACPI device to correspond to an ANDD record, we
would fail to increment our pointer and would just process the same record
over and over again, with predictable results.
Turn it from a while() loop into a for() loop to let the 'continue' in
the error paths work correctly.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If we hit this error condition then we want to return a NULL pointer and
not a freed variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As pointed out by Jörg and fixed in commit 11f1a7768 ("iommu/vt-d: Check
for NULL pointer in dmar_acpi_dev_scope_init(), this code path can
bizarrely get exercised even on AMD IOMMU systems with IRQ remapping
enabled.
In addition to the defensive check for NULL which Jörg added, let's also
just avoid calling the function at all if there aren't an Intel IOMMU
units in the system.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When ir_dev_scope_init() is called via a rootfs initcall it
will check for irq_remapping_enabled before it calls
(indirectly) into dmar_acpi_dev_scope_init() which uses the
dmar_tbl pointer without any checks.
The AMD IOMMU driver also sets the irq_remapping_enabled
flag which causes the dmar_acpi_dev_scope_init() function to
be called on systems with AMD IOMMU hardware too, causing a
boot-time kernel crash.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
In reality, the spec can only support 16-bit PASID since
INVALIDATE_IOTLB_PAGES and COMPLETE_PPR_REQUEST commands only allow 16-bit
PASID. So, we updated the PASID_MASK accordingly and invoke BUG_ON
if the hardware is reporting PASmax more than 16-bit.
Besides, max PASID is defined as ((2^(PASmax+1)) - 1). The current does not
determine this correctly.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Jay Cornwall <Jay.Cornwall@amd.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Mostly made redundant by using dev_name() instead of pci_name(), and one
instance of using *dev->dma_mask instead of pdev->dma_mask.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Should hopefully never happen (RMRRs are an abomination) but while we're
busy eliminating all the PCI assumptions, we might as well do it.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Pass the struct device to it, and also make it return the bus/devfn to use,
since that is also stored in the DMAR table.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This was problematic because it works by domain/bus/devfn and we want
to make device_to_iommu() use only a struct device * (for handling non-PCI
devices). Now that the iommu pointer is reliably stored in the
device_domain_info, we don't need to look it up.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
By moving this into get_domain_for_dev() we can make dmar_insert_dev_info()
suitable for use with "special" domains such as the si_domain, which
currently use domain_add_dev_info().
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It's not only for PCI devices any more, and the scope information for an
ACPI device provides the bus and devfn so that has to be stored here too.
It is the device pointer itself which needs to be protected with RCU,
so the __rcu annotation follows it into the definition of struct
dmar_dev_scope, since we're no longer just passing arrays of device
pointers around.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In commit 2e12bc29 ("intel-iommu: Default to non-coherent for domains
unattached to iommus") we decided to err on the side of caution and
always assume that it's possible that a device will be attached which is
behind a non-coherent IOMMU.
In some cases, however, that just *cannot* happen. If there *are* no
IOMMUs in the system which are non-coherent, then we don't need to do
it. And flushing the dcache is a *significant* performance hit.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a race condition between the existing clear/free code and the
hardware. The IOMMU is actually permitted to cache the intermediate
levels of the page tables, and doesn't need to walk the table from the
very top of the PGD each time. So the existing back-to-back calls to
dma_pte_clear_range() and dma_pte_free_pagetable() can lead to a
use-after-free where the IOMMU reads from a freed page table.
When freeing page tables we actually need to do the IOTLB flush, with
the 'invalidation hint' bit clear to indicate that it's not just a
leaf-node flush, after unlinking each page table page from the next level
up but before actually freeing it.
So in the rewritten domain_unmap() we just return a list of pages (using
pg->freelist to make a list of them), and then the caller is expected to
do the appropriate IOTLB flush (or tear down the domain completely,
whatever), before finally calling dma_free_pagelist() to free the pages.
As an added bonus, we no longer need to flush the CPU's data cache for
pages which are about to be *removed* from the page table hierarchy anyway,
in the non-cache-coherent case. This drastically improves the performance
of large unmaps.
As a side-effect of all these changes, this also fixes the fact that
intel_iommu_unmap() was neglecting to free the page tables for the range
in question after clearing them.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We have this horrid API where iommu_unmap() can unmap more than it's asked
to, if the IOVA in question happens to be mapped with a large page.
Instead of propagating this nonsense to the point where we end up returning
the page order from dma_pte_clear_range(), let's just do it once and adjust
the 'size' parameter accordingly.
Augment pfn_to_dma_pte() to return the level at which the PTE was found,
which will also be useful later if we end up changing the API for
iommu_iova_to_phys() to behave the same way as is being discussed upstream.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The iopte_free() function should check for NULL because
kmem_cache_free() will panic on NULL argument.
Signed-off-by: Zhouyi Zhou <yizhouzhou@ict.ac.cn>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Now we have a PCI bus notification based mechanism to update DMAR
device scope array, we could extend the mechanism to support boot
time initialization too, which will help to unify and simplify
the implementation.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Current Intel DMAR/IOMMU driver assumes that all PCI devices associated
with DMAR/RMRR/ATSR device scope arrays are created at boot time and
won't change at runtime, so it caches pointers of associated PCI device
object. That assumption may be wrong now due to:
1) introduction of PCI host bridge hotplug
2) PCI device hotplug through sysfs interfaces.
Wang Yijing has tried to solve this issue by caching <bus, dev, func>
tupple instead of the PCI device object pointer, but that's still
unreliable because PCI bus number may change in case of hotplug.
Please refer to http://lkml.org/lkml/2013/11/5/64
Message from Yingjing's mail:
after remove and rescan a pci device
[ 611.857095] dmar: DRHD: handling fault status reg 2
[ 611.857109] dmar: DMAR:[DMA Read] Request device [86:00.3] fault addr ffff7000
[ 611.857109] DMAR:[fault reason 02] Present bit in context entry is clear
[ 611.857524] dmar: DRHD: handling fault status reg 102
[ 611.857534] dmar: DMAR:[DMA Read] Request device [86:00.3] fault addr ffff6000
[ 611.857534] DMAR:[fault reason 02] Present bit in context entry is clear
[ 611.857936] dmar: DRHD: handling fault status reg 202
[ 611.857947] dmar: DMAR:[DMA Read] Request device [86:00.3] fault addr ffff5000
[ 611.857947] DMAR:[fault reason 02] Present bit in context entry is clear
[ 611.858351] dmar: DRHD: handling fault status reg 302
[ 611.858362] dmar: DMAR:[DMA Read] Request device [86:00.3] fault addr ffff4000
[ 611.858362] DMAR:[fault reason 02] Present bit in context entry is clear
[ 611.860819] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 611.860983] dmar: DRHD: handling fault status reg 402
[ 611.860995] dmar: INTR-REMAP: Request device [[86:00.3] fault index a4
[ 611.860995] INTR-REMAP:[fault reason 34] Present field in the IRTE entry is clear
This patch introduces a new mechanism to update the DRHD/RMRR/ATSR device scope
caches by hooking PCI bus notification.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Global DMA and interrupt remapping resources may be accessed in
interrupt context, so use RCU instead of rwsem to protect them
in such cases.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Introduce a global rwsem dmar_global_lock, which will be used to
protect DMAR related global data structures from DMAR/PCI/memory
device hotplug operations in process context.
DMA and interrupt remapping related data structures are read most,
and only change when memory/PCI/DMAR hotplug event happens.
So a global rwsem solution is adopted for balance between simplicity
and performance.
For interrupt remapping driver, function intel_irq_remapping_supported(),
dmar_table_init(), intel_enable_irq_remapping(), disable_irq_remapping(),
reenable_irq_remapping() and enable_drhd_fault_handling() etc
are called during booting, suspending and resuming with interrupt
disabled, so no need to take the global lock.
For interrupt remapping entry allocation, the locking model is:
down_read(&dmar_global_lock);
/* Find corresponding iommu */
iommu = map_hpet_to_ir(id);
if (iommu)
/*
* Allocate remapping entry and mark entry busy,
* the IOMMU won't be hot-removed until the
* allocated entry has been released.
*/
index = alloc_irte(iommu, irq, 1);
up_read(&dmar_global_lock);
For DMA remmaping driver, we only uses the dmar_global_lock rwsem to
protect functions which are only called in process context. For any
function which may be called in interrupt context, we will use RCU
to protect them in following patches.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Introduce for_each_dev_scope()/for_each_active_dev_scope() to walk
{active} device scope entries. This will help following RCU lock
related patches.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Reduce duplicated code to handle virtual machine domains, there's no
functionality changes. It also improves code readability.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Enhance function get_domain_for_dev() to release allocated resources
if failed to create domain for PCIe endpoint, otherwise the allocated
resources will get lost.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Function get_domain_for_dev() is a little complex, simplify it
by factoring out dmar_search_domain_by_dev_info() and
dmar_insert_dev_info().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Move private structures and variables into intel-iommu.c, which will
help to simplify locking policy for hotplug. Also delete redundant
declarations.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Factor out function dmar_alloc_dev_scope() from dmar_parse_dev_scope()
for later reuse.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Function device_notifier() in intel-iommu.c only remove domain_device_info
data structure associated with a PCI device when handling PCI device
driver unbinding events. If a PCI device has never been bound to a PCI
device driver, there won't be BUS_NOTIFY_UNBOUND_DRIVER event when
hot-removing the PCI device. So associated domain_device_info data
structure may get lost.
On the other hand, if iommu_pass_through is enabled, function
iommu_prepare_static_indentify_mapping() will create domain_device_info
data structure for each PCIe to PCIe bridge and PCIe endpoint,
no matter whether there are drivers associated with those PCIe devices
or not. So those domain_device_info data structures will get lost when
hot-removing the assocated PCIe devices if they have never bound to
any PCI device driver.
To be even worse, it's not only an memory leak issue, but also an
caching of stale information bug because the memory are kept in
device_domain_list and domain->devices lists.
Fix the bug by trying to remove domain_device_info data structure when
handling BUS_NOTIFY_DEL_DEVICE event.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Function device_notifier() in intel-iommu.c fails to remove
device_domain_info data structures for PCI devices if they are
associated with si_domain because iommu_no_mapping() returns true
for those PCI devices. This will cause memory leak and caching of
stale information in domain->devices list.
So fix the issue by not calling iommu_no_mapping() and skipping check
of iommu_pass_through.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The OMAP IOMMU driver locates the IOMMU associated to a device using the
IOMMU name stored in the device archdata iommu field. That field is
expected to be populated by platform code and is left unset for DT-based
devices. This results in a crash when the IOMMU driver attaches a domain
to a device.
Fix this by allocating the archdata iommu structure when devices are
added and freeing when they are removed. Devices without an OF node, and
devices without an iommus property in their OF node are ignored. The
iommu name is initialized from the IOMMU device node name.
This should be simplified when removing non-DT support completely from
the IOMMU users as the IOMMU name won't be needed anymore, and the
IOMMU device pointer could then be stored in the archdata iommu field
directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[s-anna@ti.com: updated to use device name instead of OF name]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The remoteproc MMUs in OMAP4+ SoCs have some additional debug
registers that can give out the PC value in addition to the
MMU fault address. The PC value can be extracted properly only
on the DSP cores, and is not available on the ARM processors
within the IPU sub-systems. Instead, the MMUs have been enhanced
to throw a bus-error response back to the IPU processors.
This functionality is programmable through the MMU_GP_REG register.
The cores are simply stalled if the MMU_GP_REG.BUS_ERR_BACK_EN bit
is not set. When set, a bus-error exception is raised allowing the
processor to handle it as a bus fault and provide additional debug
information. This feature is turned on by default by the driver on
iommus supporting it.
Signed-off-by: Subramaniam Chanderashekarapuram <subramaniam.ca@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
As OMAP2+ is moving to a full DT boot for all SoC families, commit
7ce93f3 "ARM: OMAP2+: Fix more missing data for omap3.dtsi file"
adds basic DT bits for OMAP3. But the driver is not yet converted,
so this will not work and driver will not be probed. Convert it!
The legacy boot mode is still supported until OMAP3 is converted
to DT-boot only.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: dev_name adaptation and improved error checking]
Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: Ack for arch/arm/*omap* parts]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
When booting with a devicetree, no platform data is provided.
Do not prematurely exit iommu_enable() and iommu_disable() in
such a case.
Note: As OMAP do not yet has a proper reset controller driver,
IOMMUs requiring a reset signal should use pdata-quirks as a
transitional solution.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
There are couple of issues with the error return paths in
omap_iommu_attach():
1. omap_iommu_attach() returns NULL or ERR_PTR in case of error,
but omap_iommu_attach_dev() only checks for IS_ERR. Thus a NULL
return value (in case driver_find_device fails) will cause the
kernel to panic when omap_iommu_attach_dev() dereferences the
pointer.
2. A try_module_get() failure returns a valid success value as
returned from iommu_enable().
Both the above issues have been fixed up to return the proper
ERR_PTR.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Use the various devm_ interfaces to simplify the cleanup in
probe and remove functions.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Commit 78a2e12f51 ("iommu: shmobile: Enable driver compilation with
COMPILE_TEST") added an optional dependency on SH_MOBILE. But that
Kconfig symbol doesn't exist. It seems ARCH_SHMOBILE was intended. Use
that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch corrects the PASID format in the INVALIDATE_IOTLB_PAGES
command, which was caused by incorrect information in
the AMD IOMMU Architectural Specification v2.01 document.
Incorrect format:
cmd->data[0][16:23] = PASID[7:0]
cmd->data[1][16:27] = PASID[19:8]
Correct format:
cmd->data[0][16:23] = PASID[15:8]
cmd->data[1][16:23] = PASID[7:0]
However, this does not affect the IOMMUv2 hardware implementation,
and has been corrected since version 2.02 of the specification
(available through AMD NDA).
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Cho KyongHo