Different SoC have different numbers of pinmux registers and other
resources that overlap with each other. To clean up the code and
eliminate defines that overlap with each other, move the PINMUX
defines to the SoC specific files.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The Timer64p timer has 8 compare registers that can
be used to generate interrupts when the timer value
matches the compare reg's value. They do not disturb
the timer itself. This can be useful when there is
only one timer available for both clock events and
clocksource.
When enabled, the clocksource remains a continuous
32-bit counter but the clock event will no longer
support periodic interrupts. Instead only oneshot
timers will be supported and implemented by setting
the compare register to the current timer value plus
the period that the clock event subsystem is requesting.
Compare registers support is enabled automatically
when the following conditions are met:
1) The same timer is being used for clock events
and clocksource.
2) The timer is the bottom half (32 bits) of the
64-bit timer (hardware limitation).
3) The the compare register offset and irq are
not zero.
Since the timer is always running, there is a hardware
race in timer32_config() between reading the current
timer value, and adding the period to the current
timer value and writing the compare register.
Testing on a da830 evm board with the timer clocked
at 24 MHz and the processor clocked at 300 MHz,
showed the number of counter ticks to do this ranged
from 20-53 (~1-2.2 usecs) but usually around 41 ticks.
This includes some artifacts from collecting the
information. So, the minimum period should be
at least 5 usecs to be safe.
There is also an non-critical lower limit that
the period should be since there is no point in
setting an event that is much shorter than the
time it takes to set the event, and get & handle
the timer interrupt for that event. There can
also be all sorts of delays from activities
occuring elsewhere in the system (including
hardware activitis like cache & TLB management).
These are virtually impossible to quantify so a
minimum period of 50 usecs was chosen. That will
certianly be enough to avoid the actual hardware
race but hopefully not large enough to cause
unreasonably course-grained timers.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The watchdog code currently hardcodes the base address
of the timer its using. To support new SoCs, make it
support timers at any address. Use the soc_info structure
to do this.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The davinci timer code currently hardcodes the timer register
base addresses, the timer irq numbers, and the timers to use
for clock events and clocksource. This won't work for some
a new SoC so put those values into the soc_info structure
and set them up in the SoC-specific files.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use clock framework instead of hard-coded CLOCK_TICK_RATE for
determining timer tick frequencies.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add arch-specific ioremap() which uses any existing static mappings in
place of doing a new mapping. From now on, drivers should always use
ioremap() instead of IO_ADDRESS().
In addition, remove the davinci_[read|write]* macros in favor of using
ioremap.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.
Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.
Fixup the existing users.
Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.
[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add base kernel support for the TI DaVinci platform.
This patch only includes interrupts, timers, CPU identification,
serial support and basic power and sleep controller init. More
drivers to come.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark A. Greer