This patch ensures that the seg6local lightweight tunnel is used solely
with IPv6 routes and processes only IPv6 packets.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the L2 frame encapsulation mechanism, referred to
as T.Encaps.L2 in the SRv6 specifications [1].
A new type of SRv6 tunnel mode is added (SEG6_IPTUN_MODE_L2ENCAP). It only
accepts packets with an existing MAC header (i.e., it will not work for
locally generated packets). The resulting packet looks like IPv6 -> SRH ->
Ethernet -> original L3 payload. The next header field of the SRH is set to
NEXTHDR_NONE.
[1] https://tools.ietf.org/html/draft-filsfils-spring-srv6-network-programming-01
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the SRv6 encapsulation mode to carry an IPv4 payload.
All the infrastructure was already present, I just had to add a parameter
to seg6_do_srh_encap() to specify the inner packet protocol, and perform
some additional checks.
Usage example:
ip route add 1.2.3.4 encap seg6 mode encap segs fc00::1,fc00::2 dev eth0
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_cookie might be used uninitialized, fix this by
initializing it.
Fixes: c5cff8561d ("ipv6: add rcu grace period before freeing fib6_node")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use skb_availroom to calculate the skb tailroom for the
ESP trailer. skb_availroom calculates the tailroom and
subtracts this value by reserved_tailroom. However
reserved_tailroom is a union with the skb mark. This means
that we subtract the tailroom by the skb mark if set.
Fix this by using skb_tailroom instead.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We allocate the page fragment for the ESP trailer inside
a spinlock, but consume it outside of the lock. This
is racy as some other cou could get the same page fragment
then. Fix this by consuming the page fragment inside the
lock too.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Allow our callers to influence the choice of ECMP link by honoring the
hash passed together with the flow info. This allows for special
treatment of ICMP errors which we would like to route over the same path
as the IPv6 datagram that triggered the error.
Also go through rt6_multipath_hash(), in the usual case when we aren't
dealing with an ICMP error, so that there is one central place where
multipath hash is computed.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 644d0e6569 ("ipv6 Use get_hash_from_flowi6 for rt6 hash") has
turned rt6_info_hash_nhsfn() into a one-liner, so it no longer makes
sense to keep it around. Also remove the accompanying comment that has
become outdated.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forwarding or sending out an ICMPv6 error, look at the embedded
packet that triggered the error and compute a flow hash over its
headers.
This let's us route the ICMP error together with the flow it belongs to
when multipath (ECMP) routing is in use, which in turn makes Path MTU
Discovery work in ECMP load-balanced or anycast setups (RFC 7690).
Granted, end-hosts behind the ECMP router (aka servers) need to reflect
the IPv6 Flow Label for PMTUD to work.
The code is organized to be in parallel with ipv4 stack:
ip_multipath_l3_keys -> ip6_multipath_l3_keys
fib_multipath_hash -> rt6_multipath_hash
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reflecting IPv6 Flow Label at server nodes is useful in environments
that employ multipath routing to load balance the requests. As "IPv6
Flow Label Reflection" standard draft [1] points out - ICMPv6 PTB error
messages generated in response to a downstream packets from the server
can be routed by a load balancer back to the original server without
looking at transport headers, if the server applies the flow label
reflection. This enables the Path MTU Discovery past the ECMP router in
load-balance or anycast environments where each server node is reachable
by only one path.
Introduce a sysctl to enable flow label reflection per net namespace for
all newly created sockets. Same could be earlier achieved only per
socket by setting the IPV6_FL_F_REFLECT flag for the IPV6_FLOWLABEL_MGR
socket option.
[1] https://tools.ietf.org/html/draft-wang-6man-flow-label-reflection-01
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_NF_CONNTRACK_PROCFS is deprecated, no need to use a function
pointer in the trackers for this. Place the printf formatting in
the one place that uses it.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
no need to waste storage for something that is only needed
in one place and can be deduced from protocol number.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
no need to waste storage for something that is only needed
in one place and can be deduced from protocol number.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
avoids a pointer and allows struct to be const later on.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When SOF_TIMESTAMPING_RX_SOFTWARE is enabled for tcp sockets, return the
timestamp corresponding to the highest sequence number data returned.
Previously the skb->tstamp is overwritten when a TCP packet is placed
in the out of order queue. While the packet is in the ooo queue, save the
timestamp in the TCB_SKB_CB. This space is shared with the gso_*
options which are only used on the tx path, and a previously unused 4
byte hole.
When skbs are coalesced either in the sk_receive_queue or the
out_of_order_queue always choose the timestamp of the appended skb to
maintain the invariant of returning the timestamp of the last byte in
the recvmsg buffer.
Signed-off-by: Mike Maloney <maloney@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently keep rt->rt6i_node pointing to the fib6_node for the route.
And some functions make use of this pointer to dereference the fib6_node
from rt structure, e.g. rt6_check(). However, as there is neither
refcount nor rcu taken when dereferencing rt->rt6i_node, it could
potentially cause crashes as rt->rt6i_node could be set to NULL by other
CPUs when doing a route deletion.
This patch introduces an rcu grace period before freeing fib6_node and
makes sure the functions that dereference it takes rcu_read_lock().
Note: there is no "Fixes" tag because this bug was there in a very
early stage.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-08-21
1) Fix memleaks when ESP takes an error path.
2) Fix null pointer dereference when creating a sub policy
that matches the same outer flow as main policy does.
From Koichiro Den.
3) Fix possible out-of-bound access in xfrm_migrate.
This patch should go to the stable trees too.
From Vladis Dronov.
4) ESP can return positive and negative error values,
so treat both cases as an error.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet length of exactly IPV6_MAXPLEN is allowed, we should
refuse parsing options only if the size is 64KiB or more.
While at it, remove one extra variable and one assignment which
were also introduced by the commit that introduced the size
check. Checking the sum 'offset + len' and only later adding
'len' to 'offset' doesn't provide any advantage over directly
summing to 'offset' and checking it.
Fixes: 6399f1fae4 ("ipv6: avoid overflow of offset in ip6_find_1stfragopt")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One nagging difference between ipv4 and ipv6 is host routes for ipv6
addresses are installed using the loopback device or VRF / L3 Master
device. e.g.,
2001:db8:1::/120 dev veth0 proto kernel metric 256 pref medium
local 2001:db8:1::1 dev lo table local proto kernel metric 0 pref medium
Using the loopback device is convenient -- necessary for local tx, but
has some nasty side effects, most notably setting the 'lo' device down
causes all host routes for all local IPv6 address to be removed from the
FIB and completely breaks IPv6 networking across all interfaces.
This patch puts FIB entries for IPv6 routes against the device. This
simplifies the routes in the FIB, for example by making dst->dev and
rt6i_idev->dev the same (a future patch can look at removing the device
reference taken for rt6i_idev for FIB entries).
When copies are made on FIB lookups, the cloned route has dst->dev
set to loopback (or the L3 master device). This is needed for the
local Tx of packets to local addresses.
With fib entries allocated against the real network device, the addrconf
code that reinserts host routes on admin up of 'lo' is no longer needed.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-08-21
1) Support RX checksum with IPsec crypto offload for esp4/esp6.
From Ilan Tayari.
2) Fixup IPv6 checksums when doing IPsec crypto offload.
From Yossi Kuperman.
3) Auto load the xfrom offload modules if a user installs
a SA that requests IPsec offload. From Ilan Tayari.
4) Clear RX offload informations in xfrm_input to not
confuse the TX path with stale offload informations.
From Ilan Tayari.
5) Allow IPsec GSO for local sockets if the crypto operation
will be offloaded.
6) Support setting of an output mark to the xfrm_state.
This mark can be used to to do the tunnel route lookup.
From Lorenzo Colitti.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In fib6_add(), it is possible that fib6_add_1() picks an intermediate
node and sets the node's fn->leaf to NULL in order to add this new
route. However, if fib6_add_rt2node() fails to add the new
route for some reason, fn->leaf will be left as NULL and could
potentially cause crash when fn->leaf is accessed in fib6_locate().
This patch makes sure fib6_repair_tree() is called to properly repair
fn->leaf in the above failure case.
Here is the syzkaller reported general protection fault in fib6_locate:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 0 PID: 40937 Comm: syz-executor3 Not tainted
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801d7d64100 ti: ffff8801d01a0000 task.ti: ffff8801d01a0000
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] __ipv6_prefix_equal64_half include/net/ipv6.h:475 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] ipv6_prefix_equal include/net/ipv6.h:492 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] fib6_locate_1 net/ipv6/ip6_fib.c:1210 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] fib6_locate+0x281/0x3c0 net/ipv6/ip6_fib.c:1233
RSP: 0018:ffff8801d01a36a8 EFLAGS: 00010202
RAX: 0000000000000020 RBX: ffff8801bc790e00 RCX: ffffc90002983000
RDX: 0000000000001219 RSI: ffff8801d01a37a0 RDI: 0000000000000100
RBP: ffff8801d01a36f0 R08: 00000000000000ff R09: 0000000000000000
R10: 0000000000000003 R11: 0000000000000000 R12: 0000000000000001
R13: dffffc0000000000 R14: ffff8801d01a37a0 R15: 0000000000000000
FS: 00007f6afd68c700(0000) GS:ffff8801db400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004c6340 CR3: 00000000ba41f000 CR4: 00000000001426f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
ffff8801d01a37a8 ffff8801d01a3780 ffffed003a0346f5 0000000c82a23ea0
ffff8800b7bd7700 ffff8801d01a3780 ffff8800b6a1c940 ffffffff82a23ea0
ffff8801d01a3920 ffff8801d01a3748 ffffffff82a223d6 ffff8801d7d64988
Call Trace:
[<ffffffff82a223d6>] ip6_route_del+0x106/0x570 net/ipv6/route.c:2109
[<ffffffff82a23f9d>] inet6_rtm_delroute+0xfd/0x100 net/ipv6/route.c:3075
[<ffffffff82621359>] rtnetlink_rcv_msg+0x549/0x7a0 net/core/rtnetlink.c:3450
[<ffffffff8274c1d1>] netlink_rcv_skb+0x141/0x370 net/netlink/af_netlink.c:2281
[<ffffffff82613ddf>] rtnetlink_rcv+0x2f/0x40 net/core/rtnetlink.c:3456
[<ffffffff8274ad38>] netlink_unicast_kernel net/netlink/af_netlink.c:1206 [inline]
[<ffffffff8274ad38>] netlink_unicast+0x518/0x750 net/netlink/af_netlink.c:1232
[<ffffffff8274b83e>] netlink_sendmsg+0x8ce/0xc30 net/netlink/af_netlink.c:1778
[<ffffffff82564aff>] sock_sendmsg_nosec net/socket.c:609 [inline]
[<ffffffff82564aff>] sock_sendmsg+0xcf/0x110 net/socket.c:619
[<ffffffff82564d62>] sock_write_iter+0x222/0x3a0 net/socket.c:834
[<ffffffff8178523d>] new_sync_write+0x1dd/0x2b0 fs/read_write.c:478
[<ffffffff817853f4>] __vfs_write+0xe4/0x110 fs/read_write.c:491
[<ffffffff81786c38>] vfs_write+0x178/0x4b0 fs/read_write.c:538
[<ffffffff817892a9>] SYSC_write fs/read_write.c:585 [inline]
[<ffffffff817892a9>] SyS_write+0xd9/0x1b0 fs/read_write.c:577
[<ffffffff82c71e32>] entry_SYSCALL_64_fastpath+0x12/0x17
Note: there is no "Fixes" tag as this seems to be a bug introduced
very early.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzcaller reported the following use-after-free issue in rt6_select():
BUG: KASAN: use-after-free in rt6_select net/ipv6/route.c:755 [inline] at addr ffff8800bc6994e8
BUG: KASAN: use-after-free in ip6_pol_route.isra.46+0x1429/0x1470 net/ipv6/route.c:1084 at addr ffff8800bc6994e8
Read of size 4 by task syz-executor1/439628
CPU: 0 PID: 439628 Comm: syz-executor1 Not tainted 4.3.5+ #8
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
0000000000000000 ffff88018fe435b0 ffffffff81ca384d ffff8801d3588c00
ffff8800bc699380 ffff8800bc699500 dffffc0000000000 ffff8801d40a47c0
ffff88018fe435d8 ffffffff81735751 ffff88018fe43660 ffff8800bc699380
Call Trace:
[<ffffffff81ca384d>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffffff81ca384d>] dump_stack+0xc1/0x124 lib/dump_stack.c:51
sctp: [Deprecated]: syz-executor0 (pid 439615) Use of struct sctp_assoc_value in delayed_ack socket option.
Use struct sctp_sack_info instead
[<ffffffff81735751>] kasan_object_err+0x21/0x70 mm/kasan/report.c:158
[<ffffffff817359c4>] print_address_description mm/kasan/report.c:196 [inline]
[<ffffffff817359c4>] kasan_report_error+0x1b4/0x4a0 mm/kasan/report.c:285
[<ffffffff81735d93>] kasan_report mm/kasan/report.c:305 [inline]
[<ffffffff81735d93>] __asan_report_load4_noabort+0x43/0x50 mm/kasan/report.c:325
[<ffffffff82a28e39>] rt6_select net/ipv6/route.c:755 [inline]
[<ffffffff82a28e39>] ip6_pol_route.isra.46+0x1429/0x1470 net/ipv6/route.c:1084
[<ffffffff82a28fb1>] ip6_pol_route_output+0x81/0xb0 net/ipv6/route.c:1203
[<ffffffff82ab0a50>] fib6_rule_action+0x1f0/0x680 net/ipv6/fib6_rules.c:95
[<ffffffff8265cbb6>] fib_rules_lookup+0x2a6/0x7a0 net/core/fib_rules.c:223
[<ffffffff82ab1430>] fib6_rule_lookup+0xd0/0x250 net/ipv6/fib6_rules.c:41
[<ffffffff82a22006>] ip6_route_output+0x1d6/0x2c0 net/ipv6/route.c:1224
[<ffffffff829e83d2>] ip6_dst_lookup_tail+0x4d2/0x890 net/ipv6/ip6_output.c:943
[<ffffffff829e889a>] ip6_dst_lookup_flow+0x9a/0x250 net/ipv6/ip6_output.c:1079
[<ffffffff82a9f7d8>] ip6_datagram_dst_update+0x538/0xd40 net/ipv6/datagram.c:91
[<ffffffff82aa0978>] __ip6_datagram_connect net/ipv6/datagram.c:251 [inline]
[<ffffffff82aa0978>] ip6_datagram_connect+0x518/0xe50 net/ipv6/datagram.c:272
[<ffffffff82aa1313>] ip6_datagram_connect_v6_only+0x63/0x90 net/ipv6/datagram.c:284
[<ffffffff8292f790>] inet_dgram_connect+0x170/0x1f0 net/ipv4/af_inet.c:564
[<ffffffff82565547>] SYSC_connect+0x1a7/0x2f0 net/socket.c:1582
[<ffffffff8256a649>] SyS_connect+0x29/0x30 net/socket.c:1563
[<ffffffff82c72032>] entry_SYSCALL_64_fastpath+0x12/0x17
Object at ffff8800bc699380, in cache ip6_dst_cache size: 384
The root cause of it is that in fib6_add_rt2node(), when it replaces an
existing route with the new one, it does not update fn->rr_ptr.
This commit resets fn->rr_ptr to NULL when it points to a route which is
replaced in fib6_add_rt2node().
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit e6afc8ace6 ("udp: remove
headers from UDP packets before queueing"), when udp packets are being
peeked the requested extra offset is always 0 as there is no need to skip
the udp header. However, when the offset is 0 and the next skb is
of length 0, it is only returned once. The behaviour can be seen with
the following python script:
from socket import *;
f=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
g=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
f.bind(('::', 0));
addr=('::1', f.getsockname()[1]);
g.sendto(b'', addr)
g.sendto(b'b', addr)
print(f.recvfrom(10, MSG_PEEK));
print(f.recvfrom(10, MSG_PEEK));
Where the expected output should be the empty string twice.
Instead, make sk_peek_offset return negative values, and pass those values
to __skb_try_recv_datagram/__skb_try_recv_from_queue. If the passed offset
to __skb_try_recv_from_queue is negative, the checked skb is never skipped.
__skb_try_recv_from_queue will then ensure the offset is reset back to 0
if a peek is requested without an offset, unless no packets are found.
Also simplify the if condition in __skb_try_recv_from_queue. If _off is
greater then 0, and off is greater then or equal to skb->len, then
(_off || skb->len) must always be true assuming skb->len >= 0 is always
true.
Also remove a redundant check around a call to sk_peek_offset in af_unix.c,
as it double checked if MSG_PEEK was set in the flags.
V2:
- Moved the negative fixup into __skb_try_recv_from_queue, and remove now
redundant checks
- Fix peeking in udp{,v6}_recvmsg to report the right value when the
offset is 0
V3:
- Marked new branch in __skb_try_recv_from_queue as unlikely.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a lock around one of the assignments prevents gcc from
tracking the state of the local 'fibmatch' variable, so it can no
longer prove that 'dst' is always initialized, leading to a bogus
warning:
net/ipv6/route.c: In function 'inet6_rtm_getroute':
net/ipv6/route.c:3659:2: error: 'dst' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This moves the other assignment into the same lock to shut up the
warning.
Fixes: 121622dba8 ("ipv6: route: make rtm_getroute not assume rtnl is locked")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To complete the sendmsg_locked and sendpage_locked implementation add
the hooks for af_inet6 as well.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_get_by_index assumes RTNL is held, use _rcu version instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 routes currently lack nexthop flags as in IPv4. This has several
implications.
In the forwarding path, it requires us to check the carrier state of the
nexthop device and potentially ignore a linkdown route, instead of
checking for RTNH_F_LINKDOWN.
It also requires capable drivers to use the user facing IPv6-specific
route flags to provide offload indication, instead of using the nexthop
flags as in IPv4.
Add nexthop flags to IPv6 routes in the 40 bytes hole and use it to
provide offload indication instead of the RTF_OFFLOAD flag, which is
removed while it's still not part of any official kernel release.
In the near future we would like to use the field for the
RTNH_F_{LINKDOWN,DEAD} flags, but this change is more involved and might
not be ready in time for the current cycle.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filtering the ACK packet was not put at the right place.
At this place, we already allocated a child and put it
into accept queue.
We absolutely need to call tcp_child_process() to release
its spinlock, or we will deadlock at accept() or close() time.
Found by syzkaller team (Thanks a lot !)
Fixes: 8fac365f63 ("tcp: Add a tcp_filter hook before handle ack packet")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dst is created by addrconf_dst_alloc() for a host route or an
anycast route, dst->dev points to loopback dev while rt6->rt6i_idev
points to a real device.
When the real device goes down, the current cleanup code only checks for
dst->dev and assumes rt6->rt6i_idev->dev is the same. This causes the
refcount leak on the real device in the above situation.
This patch makes sure to always release the refcount taken on
rt6->rt6i_idev during dst_dev_put().
Fixes: 587fea7411 ("ipv6: mark DST_NOGC and remove the operation of
dst_free()")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/mm_types.h
mm/huge_memory.c
I removed the smp_mb__before_spinlock() like the following commit does:
8b1b436dd1 ("mm, locking: Rework {set,clear,mm}_tlb_flush_pending()")
and fixed up the affected commits.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On systems that use mark-based routing it may be necessary for
routing lookups to use marks in order for packets to be routed
correctly. An example of such a system is Android, which uses
socket marks to route packets via different networks.
Currently, routing lookups in tunnel mode always use a mark of
zero, making routing incorrect on such systems.
This patch adds a new output_mark element to the xfrm state and
a corresponding XFRMA_OUTPUT_MARK netlink attribute. The output
mark differs from the existing xfrm mark in two ways:
1. The xfrm mark is used to match xfrm policies and states, while
the xfrm output mark is used to set the mark (and influence
the routing) of the packets emitted by those states.
2. The existing mark is constrained to be a subset of the bits of
the originating socket or transformed packet, but the output
mark is arbitrary and depends only on the state.
The use of a separate mark provides additional flexibility. For
example:
- A packet subject to two transforms (e.g., transport mode inside
tunnel mode) can have two different output marks applied to it,
one for the transport mode SA and one for the tunnel mode SA.
- On a system where socket marks determine routing, the packets
emitted by an IPsec tunnel can be routed based on a mark that
is determined by the tunnel, not by the marks of the
unencrypted packets.
- Support for setting the output marks can be introduced without
breaking any existing setups that employ both mark-based
routing and xfrm tunnel mode. Simply changing the code to use
the xfrm mark for routing output packets could xfrm mark could
change behaviour in a way that breaks these setups.
If the output mark is unspecified or set to zero, the mark is not
set or changed.
Tested: make allyesconfig; make -j64
Tested: https://android-review.googlesource.com/452776
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When iteratively building a UDP datagram with MSG_MORE and that
datagram exceeds MTU, consistently choose UFO or fragmentation.
Once skb_is_gso, always apply ufo. Conversely, once a datagram is
split across multiple skbs, do not consider ufo.
Sendpage already maintains the first invariant, only add the second.
IPv6 does not have a sendpage implementation to modify.
A gso skb must have a partial checksum, do not follow sk_no_check_tx
in udp_send_skb.
Found by syzkaller.
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any use of key->enabled (that is static_key_enabled and static_key_count)
outside jump_label_lock should handle its own serialization. The only
two that are not doing so are the UDP encapsulation static keys. Change
them to use static_key_enable, which now correctly tests key->enabled under
the jump label lock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1501601046-35683-3-git-send-email-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ndisc_notify is used to send unsolicited neighbor advertisements
(e.g., on a link up). Currently, the ndisc notifier is run before the
addrconf notifer which means NA's are not sent for link-local addresses
which are added by the addrconf notifier.
Fix by lowering the priority of the ndisc notifier. Setting the priority
to ADDRCONF_NOTIFY_PRIORITY - 5 means it runs after addrconf and before
the route notifier which is ADDRCONF_NOTIFY_PRIORITY - 10.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows us to later indicate to rtnetlink core that certain
doit functions should be called without acquiring rtnl_mutex.
This change should have no effect, we simply replace the last (now
unused) calcit argument with the new flag.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user hasn't installed any custom rules, don't go through the
whole FIB rules layer. This is pretty similar to f4530fa574 (ipv4:
Avoid overhead when no custom FIB rules are installed).
Using a micro-benchmark module [1], timing ip6_route_output() with
get_cycles(), with 40,000 routes in the main routing table, before this
patch:
min=606 max=12911 count=627 average=1959 95th=4903 90th=3747 50th=1602 mad=821
table=254 avgdepth=21.8 maxdepth=39
value │ ┊ count
600 │▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ 199
880 │▒▒▒░░░░░░░░░░░░░░░░ 43
1160 │▒▒▒░░░░░░░░░░░░░░░░░░░░ 48
1440 │▒▒▒░░░░░░░░░░░░░░░░░░░░░░░ 43
1720 │▒▒▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░ 59
2000 │▒▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 50
2280 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 26
2560 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 31
2840 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 28
3120 │▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 17
3400 │▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 17
3680 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
3960 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 11
4240 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 6
4520 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 6
4800 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 9
After:
min=544 max=11687 count=627 average=1776 95th=4546 90th=3585 50th=1227 mad=565
table=254 avgdepth=21.8 maxdepth=39
value │ ┊ count
540 │▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ 201
800 │▒▒▒▒▒░░░░░░░░░░░░░░░░ 63
1060 │▒▒▒▒▒░░░░░░░░░░░░░░░░░░░░░ 68
1320 │▒▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░ 39
1580 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 32
1840 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 32
2100 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 34
2360 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 33
2620 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 26
2880 │▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 22
3140 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 9
3400 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
3660 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 9
3920 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
4180 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
4440 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
At the frequency of the host during the bench (~ 3.7 GHz), this is
about a 100 ns difference on the median value.
A next step would be to collapse local and main tables, as in
0ddcf43d5d (ipv4: FIB Local/MAIN table collapse).
[1]: https://github.com/vincentbernat/network-lab/blob/master/lab-routes-ipv6/kbench_mod.c
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_warn_bad_offload triggers a warning when an skb enters the GSO
stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL
checksum offload set.
Commit b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
observed that SKB_GSO_DODGY producers can trigger the check and
that passing those packets through the GSO handlers will fix it
up. But, the software UFO handler will set ip_summed to
CHECKSUM_NONE.
When __skb_gso_segment is called from the receive path, this
triggers the warning again.
Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On
Tx these two are equivalent. On Rx, this better matches the
skb state (checksum computed), as CHECKSUM_NONE here means no
checksum computed.
See also this thread for context:
http://patchwork.ozlabs.org/patch/799015/
Fixes: b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the following seg6local actions.
- SEG6_LOCAL_ACTION_END: regular SRH processing. The DA of the packet
is updated to the next segment and forwarded accordingly.
- SEG6_LOCAL_ACTION_END_X: same as above, except that the packet is
forwarded to the specified IPv6 next-hop.
- SEG6_LOCAL_ACTION_END_DX6: decapsulate the packet and forward to
inner IPv6 packet to the specified IPv6 next-hop.
- SEG6_LOCAL_ACTION_END_B6: insert the specified SRH directly after
the IPv6 header of the packet.
- SEG6_LOCAL_ACTION_END_B6_ENCAP: encapsulate the packet within
an outer IPv6 header, containing the specified SRH.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary functions to parse, fill, and compare
seg6local rtnetlink attributes, for all defined action parameters.
- The SRH parameter defines an SRH to be inserted or encapsulated.
- The TABLE parameter defines the table to use for the route lookup of
the next segment or the inner decapsulated packet.
- The NH4 parameter defines the IPv4 next-hop for an inner decapsulated
IPv4 packet.
- The NH6 parameter defines the IPv6 next-hop for the next segment or
for an inner decapsulated IPv6 packet
- The IIF parameter defines an ingress interface index.
- The OIF parameter defines an egress interface index.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a new type of lightweight tunnel named seg6local.
A seg6local lwt is defined by a type of action and a set of parameters.
The action represents the operation to perform on the packets matching the
lwt's route, and is not necessarily an encapsulation. The set of parameters
are arguments for the processing function.
Each action is defined in a struct seg6_action_desc within
seg6_action_table[]. This structure contains the action, mandatory
attributes, the processing function, and a static headroom size required by
the action. The mandatory attributes are encoded as a bitmask field. The
static headroom is set to a non-zero value when the processing function
always add a constant number of bytes to the skb (e.g. the header size for
encapsulations).
To facilitate rtnetlink-related operations such as parsing, fill_encap,
and cmp_encap, each type of action parameter is associated to three
function pointers, in seg6_action_params[].
All actions defined in seg6_local.h are detailed in [1].
[1] https://tools.ietf.org/html/draft-filsfils-spring-srv6-network-programming-01
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports the seg6_do_srh_encap() and seg6_do_srh_inline()
functions. It also removes the CONFIG_IPV6_SEG6_INLINE knob
that enabled the compilation of seg6_do_srh_inline(). This function
is now built-in.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The seg6_validate_srh() function only allows SRHs whose active segment is
the first segment of the path. However, an application may insert an SRH
whose active segment is not the first one. Such an application might be
for example an SR-aware Virtual Network Function.
This patch enables to insert SRHs with an arbitrary active segment.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to raw socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to inet6 socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
TCP moves the data in the cb. Prior to tcp_v4_rcv (e.g., early demux) the
ingress index is obtained from IPCB using inet_sdif and after tcp_v4_rcv
tcp_v4_sdif is used.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to udp socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Early demux lookups are handled in the next patch as part of INET_MATCH
changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
esp_output_tail() and esp6_output_tail() can return negative
and positive error values. We currently treat only negative
values as errors, fix this to treat both cases as error.
Fixes: fca11ebde3 ("esp4: Reorganize esp_output")
Fixes: 383d0350f2 ("esp6: Reorganize esp_output")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Similar to commit 1c677b3d28 ("ipv4: fib: Add fib_info_hold() helper")
and commit b423cb1080 ("ipv4: fib: Export free_fib_info()") add an
helper to hold a reference on rt6_info and export rt6_release() to drop
it and potentially release the route.
This is needed so that drivers capable of FIB offload could hold a
reference on the route before queueing it for offload and drop it after
the route has been programmed to the device's tables.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is brought back up, the kernel tries to restore the
host routes tied to its permanent addresses.
However, if the host route was removed from the FIB, then we need to
reinsert it. This is done by releasing the current dst and allocating a
new, so as to not reuse a dst with obsolete values.
Since this function is called under RTNL and using the same explanation
from the previous patch, we can test if the route is in the FIB by
checking its node pointer instead of its reference count.
Tested using the following script and Andrey's reproducer mentioned
in commit 8048ced9be ("net: ipv6: regenerate host route if moved to gc
list") and linked below:
$ ip link set dev lo up
$ ip link add dummy1 type dummy
$ ip -6 address add cafe::1/64 dev dummy1
$ ip link set dev lo down # cafe::1/128 is removed
$ ip link set dev dummy1 up
$ ip link set dev lo up
The host route is correctly regenerated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Link: http://lkml.kernel.org/r/CAAeHK+zSe82vc5gCRgr_EoUwiALPnWVdWJBPwJZBpbxYz=kGJw@mail.gmail.com
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the loopback device is brought back up we need to check if the host
route attached to the address is still in the FIB and regenerate one in
case it's not.
Host routes using the loopback device are always inserted into and
removed from the FIB under RTNL (under which this function is called),
so we can test their node pointer instead of the reference count in
order to check if the route is in the FIB or not.
Tested using the following script from Nicolas mentioned in
commit a220445f9f ("ipv6: correctly add local routes when lo goes up"):
$ ip link add dummy1 type dummy
$ ip link set dummy1 up
$ ip link set lo down ; ip link set lo up
The host route is correctly regenerated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a route is deleted its node pointer is set to NULL to indicate it's
no longer linked to its node. Do the same for routes that are replaced.
This will later allow us to test if a route is still in the FIB by
checking its node pointer instead of its reference count.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently assumes that only FIB nodes can hold a reference on
routes. Therefore, after fib6_purge_rt() has run and the route is no
longer present in any intermediate nodes, it's assumed that its
reference count would be 1 - taken by the node where it's currently
stored.
However, we're going to allow users other than the FIB to take a
reference on a route, so this assumption is no longer valid and the
BUG_ON() needs to be removed.
Note that purging only takes place if the initial reference count is
different than 1. I've left that check intact, as in the majority of
systems (where routes are only referenced by the FIB), it does actually
mean the route is present in intermediate nodes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user space applications to see which routes are offloaded and
which aren't by setting the RTNH_F_OFFLOAD flag when dumping them.
To be consistent with IPv4, offload indication is provided on a
per-nexthop basis.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump all the FIB tables in each net namespace upon registration to the
FIB notification chain so that the callee will have a complete view of
the tables.
The integrity of the dump is ensured by a per-table sequence counter
that is incremented (under write lock) whenever a route is added or
deleted from the table.
All the sequence counters are read (under each table's read lock) and
summed, prior and after the dump. In case the counters differ, then the
dump is either restarted or the registration fails.
While it's possible for a table to be modified after its counter has
been read, this isn't really a problem. In case it happened before it
was read the second time, then the comparison at the end will fail. If
it happened afterwards, then we're guaranteed to be notified about the
change, as the notification block is registered prior to the second
read.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users of the FIB notification chain to receive a complete view of
the IPv6 FIB rules upon registration to the chain.
The integrity of the dump is ensured by a per-family sequence counter
that is incremented (under RTNL) whenever a rule is added or deleted.
All the sequence counters are read (under RTNL) and summed, prior and
after the dump. In case the counters differ, then the dump is either
restarted or the registration fails.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with IPv4, allow listeners of the FIB notification chain to receive
notifications whenever a route is added, replaced or deleted. This is
done by placing calls to the FIB notification chain in the two lowest
level functions that end up performing these operations - namely,
fib6_add_rt2node() and fib6_del_route().
Unlike IPv4, APPEND notifications aren't sent as the kernel doesn't
distinguish between "append" (NLM_F_CREATE|NLM_F_APPEND) and "prepend"
(NLM_F_CREATE). If NLM_F_EXCL isn't set, duplicate routes are always
added after the existing duplicate routes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to add IPv6 FIB offload support, so implement the necessary
callbacks in IPv6 code, which will later allow us to add routes and
rules notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit 3c71006d15 ("ipv4: fib_rules: Check if rule is
a default rule"), drivers supporting IPv6 FIB offload need to be able to
sanitize the rules they don't support and potentially flush their
tables.
Add an IPv6 helper to check if a FIB rule is a default rule.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c2ed1880fd ("net: ipv6: check route protocol when
deleting routes"), ipv6 route checks rt protocol when trying to
remove a rt entry.
It introduced a side effect causing 'ip -6 route flush cache' not
to work well. When flushing caches with iproute, all route caches
get dumped from kernel then removed one by one by sending DELROUTE
requests to kernel for each cache.
The thing is iproute sends the request with the cache whose proto
is set with RTPROT_REDIRECT by rt6_fill_node() when kernel dumps
it. But in kernel the rt_cache protocol is still 0, which causes
the cache not to be matched and removed.
So the real reason is rt6i_protocol in the route is not set when
it is allocated. As David Ahern's suggestion, this patch is to
set rt6i_protocol properly in the route when it is installed and
remove the codes setting rtm_protocol according to rt6i_flags in
rt6_fill_node.
This is also an improvement to keep rt6i_protocol consistent with
rtm_protocol.
Fixes: c2ed1880fd ("net: ipv6: check route protocol when deleting routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_loginfo structures are only passed as the seventh argument to
nf_log_trace, which is declared as const or stored in a local const
variable. Thus the nf_loginfo structures themselves can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct nf_loginfo i@p = { ... };
@ok1@
identifier r.i;
expression list[6] es;
position p;
@@
nf_log_trace(es,&i@p,...)
@ok2@
identifier r.i;
const struct nf_loginfo *e;
position p;
@@
e = &i@p
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct nf_loginfo e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct nf_loginfo i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
IPSec crypto offload depends on the protocol-specific
offload module (such as esp_offload.ko).
When the user installs an SA with crypto-offload, load
the offload module automatically, in the same way
that the protocol module is loaded (such as esp.ko)
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Both ip6_input_finish (non-GRO) and esp6_gro_receive (GRO) strip
the IPv6 header without adjusting skb->csum accordingly. As a
result CHECKSUM_COMPLETE breaks and "hw csum failure" is written
to the kernel log by netdev_rx_csum_fault (dev.c).
Fix skb->csum by substracting the checksum value of the pulled IPv6
header using a call to skb_postpull_rcsum.
This affects both transport and tunnel modes.
Note that the fix occurs far from the place that the header was
pulled. This is based on existing code, see:
ipv6_srh_rcv() in exthdrs.c and rawv6_rcv() in raw.c
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm6_transport_finish rebuilds the IPv6 header based on the
original one and pushes it back without fixing skb->csum.
Therefore, CHECKSUM_COMPLETE is no longer valid and the packet
gets dropped.
Fix skb->csum by calling skb_postpush_rcsum.
Note: A valid IPv4 header has checksum 0, unlike IPv6. Thus,
the change is not needed in the sibling xfrm4_transport_finish
function.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Keep the device's reported ip_summed indication in case crypto
was offloaded by the device. Subtract the csum values of the
stripped parts (esp header+iv, esp trailer+auth_data) to keep
value correct.
Note: CHECKSUM_COMPLETE should be indicated only if skb->csum
has the post-decryption offload csum value.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3a3a4e3054.
inet6_add_protocol and inet6_del_protocol include casts that remove the
effect of the const annotation on their parameter, leading to possible
runtime crashes.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 67a51780ae ("ipv6: udp: leverage scratch area
helpers") udp6_recvmsg() read the skb len from the scratch area,
to avoid a cache miss.
But the UDP6 rx path support RFC 2675 UDPv6 jumbograms, and their
length exceeds the 16 bits available in the scratch area. As a side
effect the length returned by recvmsg() is:
<ingress datagram len> % (1<<16)
This commit addresses the issue allocating one more bit in the
IP6CB flags field and setting it for incoming jumbograms.
Such field is still in the first cacheline, so at recvmsg()
time we can check it and fallback to access skb->len if
required, without a measurable overhead.
Fixes: 67a51780ae ("ipv6: udp: leverage scratch area helpers")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to go through sk->sk_net to access the net namespace
and its sysctl variables because we allocate the sock and initialize
sk_net just a few lines earlier in the same routine.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prequeue is a tcp receive optimization that moves part of rx processing
from bh to process context.
This only works if the socket being processed belongs to a process that
is blocked in recv on that socket.
In practice, this doesn't happen anymore that often because nowadays
servers tend to use an event driven (epoll) model.
Even normal client applications (web browsers) commonly use many tcp
connections in parallel.
This has measureable impact only in netperf (which uses plain recv and
thus allows prequeue use) from host to locally running vm (~4%), however,
there were no changes when using netperf between two physical hosts with
ixgbe interfaces.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discussion during NFWS 2017 in Faro has shown that the current
conntrack behaviour is unreasonable.
Even if conntrack module is loaded on behalf of a single net namespace,
its turned on for all namespaces, which is expensive. Commit
481fa37347 ("netfilter: conntrack: add nf_conntrack_default_on sysctl")
attempted to provide an alternative to the 'default on' behaviour by
adding a sysctl to change it.
However, as Eric points out, the sysctl only becomes available
once the module is loaded, and then its too late.
So we either have to move the sysctl to the core, or, alternatively,
change conntrack to become active only once the rule set requires this.
This does the latter, conntrack is only enabled when a rule needs it.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We no longer place these on a list so they can be const.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a preparatory patch for adding fib support to the netdev family.
The netdev family receives the packets from ingress hook. At this point
we have no guarantee that the ip header is linear. So this patch
replaces ip_hdr with skb_header_pointer in order to address that
possible situation.
Signed-off-by: Pablo M. Bermudo Garay <pablombg@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When an early demuxed packet reaches __udp6_lib_lookup_skb(), the
sk reference is retrieved and used, but the relevant reference
count is leaked and the socket destructor is never called.
Beyond leaking the sk memory, if there are pending UDP packets
in the receive queue, even the related accounted memory is leaked.
In the long run, this will cause persistent forward allocation errors
and no UDP skbs (both ipv4 and ipv6) will be able to reach the
user-space.
Fix this by explicitly accessing the early demux reference before
the lookup, and properly decreasing the socket reference count
after usage.
Also drop the skb_steal_sock() in __udp6_lib_lookup_skb(), and
the now obsoleted comment about "socket cache".
The newly added code is derived from the current ipv4 code for the
similar path.
v1 -> v2:
fixed the __udp6_lib_rcv() return code for resubmission,
as suggested by Eric
Reported-by: Sam Edwards <CFSworks@gmail.com>
Reported-by: Marc Haber <mh+netdev@zugschlus.de>
Fixes: 5425077d73 ("net: ipv6: Add early demux handler for UDP unicast")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet6_protocol structure is only passed as the first argument to
inet6_add_protocol or inet6_del_protocol, both of which are declared as
const. Thus the inet6_protocol structure itself can be const.
Also drop __read_mostly where present on the newly const structures.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 2465 defines ipv6IfStatsOutFragFails as:
"The number of IPv6 datagrams that have been discarded
because they needed to be fragmented at this output
interface but could not be."
The existing implementation, instead, would increase the counter
twice in case we fail to allocate room for single fragments:
once for the fragment, once for the datagram.
This didn't look intentional though. In one of the two affected
affected failure paths, the double increase was simply a result
of a new 'goto fail' statement, introduced to avoid a skb leak.
The other path appears to be affected since at least 2.6.12-rc2.
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Fixes: 1d325d217c ("ipv6: ip6_fragment: fix headroom tests and skb leak")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last (4th) argument of tcp_rcv_established() is redundant as it
always equals to skb->len and the skb itself is always passed as 2th
agrument. There is no reason to have it.
Signed-off-by: Ilya V. Matveychikov <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, offset can overflow and can cause an infinite loop in
ip6_find_1stfragopt(). Make it unsigned int to prevent the overflow, and
cap it at IPV6_MAXPLEN, since packets larger than that should be invalid.
This problem has been here since before the beginning of git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After rcu conversions performance degradation in forward tests isn't that
noticeable anymore.
See next patch for some numbers.
A followup patcg could then also remove genid from the policies
as we do not cache bundles anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
revert c386578f1c ("xfrm: Let the flowcache handle its size by default.").
Once we remove flow cache, we don't have a flow cache limit anymore.
We must not allow (virtually) unlimited allocations of xfrm dst entries.
Revert back to the old xfrm dst gc limits.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert reported a failure to add different mpls encaps in a multipath
route:
$ ip -6 route add 1234::/16 \
nexthop encap mpls 10 via fe80::1 dev ens3 \
nexthop encap mpls 20 via fe80::1 dev ens3
RTNETLINK answers: File exists
The problem is that the duplicate nexthop detection does not compare
lwtunnel configuration. Add it.
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reported-by: João Taveira Araújo <joao.taveira@gmail.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Lebrun