The hub driver was recently changed to use "global" suspend for system
suspend transitions on non-SuperSpeed buses. This means that we don't
suspend devices individually by setting the suspend feature on the
upstream hub port; instead devices all go into suspend automatically
when the root hub stops transmitting packets. The idea was to save
time and to avoid certain kinds of wakeup races.
Now it turns out that many hubs are buggy; they don't relay wakeup
requests from a downstream port to their upstream port if the
downstream port's suspend feature is not set (depending on the speed
of the downstream port, whether or not the hub is enabled for remote
wakeup, and possibly other factors).
We can't have hubs dropping wakeup requests. Therefore this patch
goes partway back to the old policy: It sets the suspend feature for a
port if the device attached to that port or any of its descendants is
enabled for wakeup. People will still be able to benefit from the
time savings if they don't care about wakeup and leave it disabled on
all their devices.
In order to accomplish this, the patch adds a new field to the usb_hub
structure: wakeup_enabled_descendants is a count of how many devices
below a suspended hub are enabled for remote wakeup. A corresponding
new subroutine determines the number of wakeup-enabled devices at or
below an arbitrary suspended USB device.
This should be applied to the 3.10 stable kernel.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hub_to_struct_hub() can return NULL in some unlikely cases.
Add checks where appropriate, or pass the hub pointer as an additional
argument if it's known to be valid.
The places it makes sense to check usb_hub_to_struct_hub()
are picked based on feedback from Alan Stern.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add usb port auto power off mechanism.
When usb device is suspending, usb core will suspend usb port and
usb port runtime pm callback will clear PORT_POWER feature to
power off port if all conditions were met. These conditions are
remote wakeup disable, pm qos NO_POWER_OFF flag clear and persist
enable. When it resumes, power on port again.
Add did_runtime_put in the struct usb_port to ensure
pm_runtime_get/put(portdev) to be called pairedly. Set did_runtime_put
to true when call pm_runtime_put(portdev) during suspending. The
pm_runtime_get(portdev) only will be called when did_runtime_put
is set to true during resuming. Set did_runtime_put to false after
calling pm_runtime_get(portdev).
Make clear_port_feature() and hdev_to_hub() as global symbol.
Rename clear_port_feature() to usb_clear_port_feature() and
hdev_to_hub() to usb_hub_to_struct_hub().
Extend hub_port_debounce() with the fuction of debouncing to
be connected. Add two wraps: hub_port_debounce_be_connected()
and hub_port_debouce_be_stable().
Increase HUB_DEBOUNCE_TIMEOUT to 2000 because some usb ssds
needs around 1.5 or more to make the hub port status to be
connected steadily after being powered off and powered on.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add runtime pm callback for usb port device.
Set/clear PORT_POWER feature in the resume/suspend callback.
Add portnum for struct usb_port to record port number. Do
pm_rumtime_get_sync/put(portdev) when a device is plugged/unplugged
to prevent it from being powered off when it is active.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1646) fixes a long-standing bug in the USB hub driver.
Upon conversion from char to unsigned long, the bytes in the status
buffer are subject to unwanted sign extension. The bytes should be
declared as u8 rather than char, to prevent this.
This effects of this bug are minimal. The hub driver may end up doing
a little unnecessary extra work because it thinks events have occurred
on some ports when they really haven't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to create driver/usb/core/(port.c,hub.h) files and move usb
port related code into port.c.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hub.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1255) updates the interface for calling
usb_hub_clear_tt_buffer(). Even the name of the function is changed!
When an async URB (i.e., Control or Bulk) going through a high-speed
hub to a non-high-speed device is cancelled or fails, the hub's
Transaction Translator buffer may be left busy still trying to
complete the transaction. The buffer has to be cleared; that's what
usb_hub_clear_tt_buffer() does.
It isn't safe to send any more URBs to the same endpoint until the TT
buffer is fully clear. Therefore the HCD needs to be told when the
Clear-TT-Buffer request has finished. This patch adds a callback
method to struct hc_driver for that purpose, and makes the hub driver
invoke the callback at the proper time.
The patch also changes a couple of names; "hub_tt_kevent" and
"tt.kevent" now look rather antiquated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add USB 3.0 root hub descriptors. This is a kludge because I reused the old
USB 2.0 descriptors, instead of using the new USB 3.0 hub descriptors with
endpoint companion descriptors and other descriptors. I did this because I
wasn't ready to add USB 3.0 hub changes to khubd. For now, a USB 3.0 roothub
looks like a USB 2.0 roothub, with a higher speed.
USB 3.0 hubs have no transaction translator (TT).
Make USB core debugging handle super speed ports.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to be able to call ep0_reinit() [renamed to usb_ep0_reinit()]
from the WUSB security code. The reason is that when we authenticate
the device, it's address changes (from having bit 7 set to having it
cleared). Thus, we need to signal the USB stack to reinitialize EP0,
so the status with the previous address kept at the HCD layer is
cleared and properly reinitialized.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a new PM-related change notice for the USB 2.0 specification
called "Link Power Management" (LPM). It defines a new "L1 Suspend"
state which resembles the current (L2) suspend state, except that it
can be entered and exited much more quickly. It should thus be more
useful for runtime PM, even though it doesn't mandate reduced power
draw from VBUS.
This patch provides the relevant #defines for usbcore. Actually
implementing these mechanisms requires host silicon that can generate
new USB packets, plus hubs handling some new requests and peripherals
which understand the new packets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as809b) moves the declaration of the hub driver's private
data structure from hub.h into the hub.c source file. Lots of other
files import hub.h; they have no need to know about the details of the
hub driver's private data.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current Wireless USB host hardware (Intel i1480 for example) allows up
to 22 devices to connect, thus bringing up the max number of children
in the WUSB Host Controller to 22 'fake' ports. Upcoming hardware
might raise that limit.
Makes almost no difference to go to 31, as the bit arrays are
byte-aligned (plus an extra bit in general), so 22 bits fit in 4 bytes
as 31 do.
As well, the only other array that depends on USB_MAXCHILDREN is
'struct usb_hub->indicator'. By declaring it 'u8' instead of 'enum
hub_led_mode', we reduce the size of each entry from 4 bytes (in i386)
to 1, which will add as we when are doubling USB_MAXCHILDREN
(with 16 the size of that array is 64 bytes, with 31 would be 128; by
using u8 that goes down to 31 bytes).
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't want khubd to start interfering in the device-resume process
merely because the PORT_STATUS_C_SUSPEND feature happens to be set.
Ports need to be marked as busy while a resume is taking place.
In addition, so long as ports are marked as busy, khubd won't be able to
clear their various status-change features. On an interrupt-driven root
hub this could lead to an interrupt storm. Root hub IRQs should not be
re-enabled until the busy_bits value is equal to 0.
This patch (as765) fixes these two potential problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as609) changes the way we keep track of power budgeting for
USB hubs and devices, and it updates the choose_configuration routine to
take this information into account. (This is something we should have
been doing all along.) A new field in struct usb_device holds the amount
of bus current available from the upstream port, and the usb_hub structure
keeps track of the current available for each downstream port.
Two new rules for configuration selection are added:
Don't select a self-powered configuration when only bus power
is available.
Don't select a configuration requiring more bus power than is
available.
However the first rule is #if-ed out, because I found that the internal
hub in my HP USB keyboard claims that its only configuration is
self-powered. The rule would prevent the configuration from being chosen,
leaving the hub & keyboard unconfigured. Since similar descriptor errors
may turn out to be fairly common, it seemed wise not to include a rule
that would break automatic configuration unnecessarily for such devices.
The second rule may also trigger unnecessarily, although this should be
less common. More likely it will annoy people by sometimes failing to
accept configurations that should never have been chosen in the first
place.
The patch also changes usbcore's reaction when no configuration is
suitable. Instead of raising an error and rejecting the device, now
the core will simply leave the device unconfigured. People can always
work around such problems by installing configurations manually through
sysfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also has the nice benefit of making sparc alignment issues go away.
Thanks to David Miller for pointing out the problems here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 22 ++++++++++++----------
drivers/usb/core/hub.h | 2 +-
2 files changed, 13 insertions(+), 11 deletions(-)
This adds think_time to the usb_tt struct and sets it appropriately
(measured in ns); this can help us implement better split transaction
scheduling.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the hub_set_power_budget routine, which was used by a
couple of HCDs to indicate that the root hub was running on battery power.
In its place is a new field added to struct usb_hcd, which HCDs can set
before the root hub is registered. Special-case code in the hub driver
knows to look at this field when configuring a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Rahul Bedarkar