Move declarations for these functions:
pci_dev_specific_acs_enabled()
pci_dev_specific_enable_acs()
from include/linux/pci.h to drivers/pci/pci.h because nothing outside the
PCI core needs to use them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
* lorenzo/pci/dwc:
PCI: qcom: add runtime pm support to pcie_port
PCI: qcom: Fix a bitwise vs logical NOT typo
PCI: dwc: dra7xx: Use devm_ioremap_resource() instead of devm_ioremap()
PCI: dwc: artpec6: Use devm_ioremap_resource() instead of devm_ioremap()
misc: pci_endpoint_test: Add DesignWare EP entry
dt-bindings: PCI: designware: Add support for EP in DesignWare driver
PCI: dwc: Add support for EP mode
dt-bindings: PCI: designware: Example update
PCI: Move private DT related functions into private header
PCI: dwc: Move CONFIG_PCI depends to menu
PCI: dwc: Replace magic number by defines
PCI: dwc: Small computation improvement
PCI: dwc: Replace lower into upper case characters
PCI: dwc: Define maximum number of vectors
PCI: imx6: Remove space before tabs
PCI: keystone: Do not treat link up message as error
# Conflicts:
# include/linux/of_pci.h
Pass the service type to pcie_do_fatal_recovery() instead of assuming AER.
We will make DPC also use pcie_do_fatal_recovery(), and it needs to do
things a little differently for AER and DPC.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the error reporting callbacks from aerdrv_core.c to err.c, where they
can be used by DPC in addition to AER.
As part of aerdrv_core.c, these callbacks were built under CONFIG_PCIEAER.
Moving them to the new err.c means they will now be built under
CONFIG_PCIEPORTBUS, so adjust the definition of pci_uevent_ers() to match.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: in reset_link(), initialize "driver" even if CONFIG_PCIEAER is
unset, update pci_uevent_ers() #ifdef wrapper]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clients such as hotplug and Downstream Port Containment (DPC) both need to
wait until a link becomes active or inactive.
Add a generic pcie_wait_link_active() interface and use it instead of
duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The functions in linux/of_pci.h are primarily used by host bridge
drivers, so they can be private to drivers/pci/.
The remaining functions are still used mostly in host bridge drivers
that still live in arch specific code. Hopefully someday, those will get
moved into drivers/pci as well.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization (KarimAllah
Ahmed)
* pci/virtualization:
PCI/IOV: Add missing prototypes for powerpc pcibios interfaces
PCI/IOV: Use VF0 cached config registers for other VFs
PCI/IOV: Skip BAR sizing for VFs
PCI/IOV: Skip INTx config reads for VFs
PCI: Wait for device to become ready after secondary bus reset
PCI: Add a return type for pci_reset_bridge_secondary_bus()
PCI: Wait for device to become ready after a power management reset
PCI: Rename pci_flr_wait() to pci_dev_wait() and make it generic
PCI: Handle FLR failure and allow other reset types
PCI: Protect restore with device lock to be consistent
PCI: Add function 1 DMA alias quirk for Marvell 88SE9220
PCI: Add ACS quirk for Ampere root ports
PCI: Remove redundant probes for device reset support
PCI: Probe for device reset support during enumeration
Conflicts:
include/linux/pci.h
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
Cache some config data from VF0 and use it for all other VFs instead of
reading it from the config space of each VF. We assume these items are the
same across all associated VFs:
Revision ID
Class Code
Subsystem Vendor ID
Subsystem ID
This is an optimization when enabling SR-IOV on a device with many VFs.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
[bhelgaas: changelog, simplify comments, remove unused "device", test
CONFIG_PCI_IOV instead of CONFIG_PCI_ATS, rename functions]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Add pcie_bandwidth_capable() to compute the max link bandwidth supported by
a device, based on the max link speed and width, adjusted by the encoding
overhead.
The maximum bandwidth of the link is computed as:
max_link_width * max_link_speed * (1 - encoding_overhead)
2.5 and 5.0 GT/s links use 8b/10b encoding, which reduces the raw bandwidth
available by 20%; 8.0 GT/s and faster links use 128b/130b encoding, which
reduces it by about 1.5%.
The result is in Mb/s, i.e., megabits/second, of raw bandwidth.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: add 16 GT/s, adjust for pcie_get_speed_cap() and
pcie_get_width_cap() signatures, don't export outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pcie_get_width_cap() to find the max link width supported by a device.
Change max_link_width_show() to use pcie_get_width_cap().
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: return width directly instead of error and *width, don't export
outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Add pcie_get_speed_cap() to find the max link speed supported by a device.
Change max_link_speed_show() to use pcie_get_speed_cap().
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: return speed directly instead of error and *speed, don't export
outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
The VPD-related structures are only used in vpd.c, so move them from
drivers/pci/pci.h to vpd.c. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the VPD-related sysfs code from pci-sysfs.c to vpd.c. This follows
the pattern of pcie_aspm_create_sysfs_dev_files(). The goal is to
encapsulate all the VPD code and structures in vpd.c.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pcie_clear_root_pme_status() from the port driver to the PCI core so
it will be available even when the port driver isn't present. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Several of the interfaces defined in include/linux/pci-aspm.h are used only
internally from the PCI core:
pcie_aspm_init_link_state()
pcie_aspm_exit_link_state()
pcie_aspm_pm_state_change()
pcie_aspm_powersave_config_link()
pcie_aspm_create_sysfs_dev_files()
pcie_aspm_remove_sysfs_dev_files()
Move these to the internal drivers/pci/pci.h header so they don't clutter
the driver interface.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/virtualization:
PCI: Document reset method return values
PCI: Detach driver before procfs & sysfs teardown on device remove
PCI: Apply Cavium ThunderX ACS quirk to more Root Ports
PCI: Set Cavium ACS capability quirk flags to assert RR/CR/SV/UF
PCI: Restore ARI Capable Hierarchy before setting numVFs
PCI: Create SR-IOV virtfn/physfn links before attaching driver
PCI: Expose SR-IOV offset, stride, and VF device ID via sysfs
PCI: Cache the VF device ID in the SR-IOV structure
PCI: Add Kconfig PCI_IOV dependency for PCI_REALLOC_ENABLE_AUTO
PCI: Remove unused function __pci_reset_function()
PCI: Remove reset argument from pci_iov_{add,remove}_virtfn()
* pci/resource:
PCI: Fail pci_map_rom() if the option ROM is invalid
PCI: Move pci_map_rom() error path
x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)
PCI: Add pci_resize_resource() for resizing BARs
PCI: Add resizable BAR infrastructure
PCI: Add PCI resource type mask #define
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add resizable BAR infrastructure, including defines and helper functions to
read the possible sizes of a BAR and update its size. See PCIe r3.1, sec
7.22.
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_Resizable-BAR_24Apr2008.pdf
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: rename to functions with "rebar" (to match #defines), drop shift
#defines, drop "_MASK" suffixes, fix typos, fix kerneldoc]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cache the VF device ID in the SR-IOV structure and use it instead of
reading it over and over from the PF config space capability.
Signed-off-by: Filippo Sironi <sironi@amazon.de>
[bhelgaas: rename to "vf_device" to match pci_dev->device]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make this const as it not modified in the file referencing it. It is only
stored in a const field 'type' of a device structure. Also, add const to
the variable declaration in the header file.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT2100 seems to have issues with handling 8-bit tags. Mark it
as broken.
The pci_walk_bus() in the quirk handles devices we've enumerated in the
past, and pci_configure_device() handles devices we enumerate in the
future.
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1467674
Reported-and-tested-by: Wim ten Have <wim.ten.have@oracle.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, tweak messages, rename bit and quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit dc15e71eef (PCI / PM: Restore PME Enable if skipping wakeup
setup) introduced a mechanism by which the PME Enable bit can be
restored by pci_enable_wake() if dev->wakeup_prepared is set in
case it has been overwritten by PCI config space restoration.
However, that commit overlooked the fact that on some systems (Dell
XPS13 9360 in particular) the AML handling wakeup events checks PME
Status and PME Enable and it won't trigger a Notify() for devices
where those bits are not set while it is running.
That happens during resume from suspend-to-idle when pci_restore_state()
invoked by pci_pm_default_resume_early() clears PME Enable before the
wakeup events are processed by AML, effectively causing those wakeup
events to be ignored.
Fix this issue by restoring the PME Enable configuration right after
pci_restore_state() has been called instead of doing that in
pci_enable_wake().
Fixes: dc15e71eef (PCI / PM: Restore PME Enable if skipping wakeup setup)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
After previous changes it is not necessary to distinguish between
device wakeup for run time and device wakeup from system sleep states
any more, so rework the PCI device wakeup settings code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Every method in struct device_driver or structures derived from it like
struct pci_driver MUST provide exclusion vs the driver's ->remove() method,
usually by using device_lock().
Protect use of pci_driver->sriov_configure() by holding the device lock
while calling it.
The PCI core sets the pci_dev->driver pointer in local_pci_probe() before
calling ->probe() and only clears it after ->remove(). This means driver's
->sriov_configure() callback will happily race with probe() and remove(),
most likely leading to BUGs, since drivers don't expect this.
Remove the iov lock completely, since we remove the last user.
[bhelgaas: changelog, thanks to Christoph for locking rule]
Link: http://lkml.kernel.org/r/20170522225023.14010-1-jakub.kicinski@netronome.com
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
* pci/virtualization:
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: Call pcie_flr() from reset_chelsio_generic_dev()
PCI: Call pcie_flr() from reset_intel_82599_sfp_virtfn()
PCI: Export pcie_flr()
PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding
PCI: Avoid FLR for Intel 82579 NICs
Conflicts:
include/linux/pci.h
* pci/resource-mmap:
ia64: Use generic pci_mmap_resource_range()
ia64: Remove redundant checks for WC in pci_mmap_page_range()
ia64: Remove redundant valid_mmap_phys_addr_range() from pci_mmap_page_range()
PCI: Add I/O BAR support to generic pci_mmap_resource_range()
x86/PCI: Use generic pci_mmap_resource_range()
unicore32/PCI: Use generic pci_mmap_resource_range()
sh/PCI: Use generic pci_mmap_resource_range()
parisc: Use generic pci_mmap_resource_range()
mn10300/PCI: Use generic pci_mmap_resource_range()
MIPS: PCI: Use generic pci_mmap_resource_range()
cris/PCI: Use generic pci_mmap_resource_range()
ARM/PCI: Use generic pci_mmap_resource_range()
PCI: Add pci_mmap_resource_range() and use it for ARM64
PCI: Add BAR index argument to pci_mmap_page_range()
PCI: Use BAR index in sysfs attr->private instead of resource pointer
PCI: Add arch_can_pci_mmap_io() on architectures which can mmap() I/O space
PCI: Move multiple declarations of pci_mmap_page_range() to <linux/pci.h>
PCI: Add arch_can_pci_mmap_wc() macro
xtensa/PCI: Do not mmap PCI BARs to userspace as write-through
PCI: Only allow WC mmap on prefetchable resources
PCI: Fix another sanity check bug in /proc/pci mmap
PCI: Fix pci_mmap_fits() for HAVE_PCI_RESOURCE_TO_USER platforms
Sometimes it is not desirable to bind SR-IOV VFs to drivers. This can save
host side resource usage by VF instances that will be assigned to VMs.
Add a new PCI sysfs interface "sriov_drivers_autoprobe" to control that
from the PF. To modify it, echo 0/n/N (disable probe) or 1/y/Y (enable
probe) to:
/sys/bus/pci/devices/<DOMAIN:BUS:DEVICE.FUNCTION>/sriov_drivers_autoprobe
Note that this must be done before enabling VFs. The change will not take
effect if VFs are already enabled. Simply, one can disable VFs by setting
sriov_numvfs to 0, choose whether to probe or not, and then re-enable the
VFs by restoring sriov_numvfs.
[bhelgaas: changelog, ABI doc]
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Starting to leave behind the legacy of the pci_mmap_page_range() interface
which takes "user-visible" BAR addresses. This takes just the resource and
offset.
For now, both APIs coexist and depending on the platform, one is
implemented as a wrapper around the other.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Detect on probe whether a PCI device is part of a Thunderbolt controller.
Intel uses a Vendor-Specific Extended Capability (VSEC) with ID 0x1234
on such devices. Detect presence of this VSEC and cache it in a newly
added is_thunderbolt bit in struct pci_dev.
Also, add a helper to check whether a given PCI device is situated on a
Thunderbolt daisy chain (i.e., below a PCI device with is_thunderbolt
set).
The necessity arises from the following:
* If an external Thunderbolt GPU is connected to a dual GPU laptop,
that GPU is currently registered with vga_switcheroo even though it
can neither drive the laptop's panel nor be powered off by the
platform. To vga_switcheroo it will appear as if two discrete
GPUs are present. As a result, when the external GPU is runtime
suspended, vga_switcheroo will cut power to the internal discrete GPU
which may not be runtime suspended at all at this moment. The
solution is to not register external GPUs with vga_switcheroo, which
necessitates a way to recognize if they're on a Thunderbolt daisy
chain.
* Dual GPU MacBook Pros introduced 2011+ can no longer switch external
DisplayPort ports between GPUs. (They're no longer just used for DP
but have become combined DP/Thunderbolt ports.) The driver to switch
the ports, drivers/platform/x86/apple-gmux.c, needs to detect presence
of a Thunderbolt controller and, if found, keep external ports
permanently switched to the discrete GPU.
v2: Make kerneldoc for pci_is_thunderbolt_attached() more precise,
drop portion of commit message pertaining to separate series.
(Bjorn Helgaas)
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Amir Levy <amir.jer.levy@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/0ab165a4a35c0b60f29d4c306c653ead14fcd8f9.1489145162.git.lukas@wunner.de
Add a new state to pci_dev to be set when it is unexpectedly disconnected.
The PCI driver tear down functions can observe this new device state so
they may skip operations that will fail.
The pciehp and pcie-dpc drivers are aware when the link is down, so these
set the flag when their handlers detect the device is disconnected.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
* pci/virtualization:
PCI: Add comments about ROM BAR updating
PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE
PCI: Remove pci_resource_bar() and pci_iov_resource_bar()
PCI: Don't update VF BARs while VF memory space is enabled
PCI: Separate VF BAR updates from standard BAR updates
PCI: Update BARs using property bits appropriate for type
PCI: Ignore BAR updates on virtual functions
PCI: Do any VF BAR updates before enabling the BARs
PCI: Support INTx masking on ConnectX-4 with firmware x.14.1100+
PCI: Convert Mellanox broken INTx quirks to be for listed devices only
PCI: Convert broken INTx masking quirks from HEADER to FINAL
net/mlx4_core: Use device ID defines
PCI: Add Mellanox device IDs
* pci/pm:
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Unfold conditions to block runtime PM on PCIe ports
PCI: Consolidate conditions to allow runtime PM on PCIe ports
PCI: Activate runtime PM on a PCIe port only if it can suspend
PCI: Speed up algorithm in pci_bridge_d3_update()
PCI: Autosense device removal in pci_bridge_d3_update()
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
USB: UHCI: report non-PME wakeup signalling for Intel hardware
PCI: Check for PME in targeted sleep state
Move PCI configuration space size macros (PCI_CFG_SPACE_SIZE and
PCI_CFG_SPACE_EXP_SIZE) from drivers/pci/pci.h to
include/uapi/linux/pci_regs.h so they can be used by more drivers and
eliminate duplicate definitions.
[bhelgaas: Expand comment to include PCI-X details]
Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The acpi_get_rc_resources() is used to get the RC register address that can
not be described in MCFG. It takes the _HID & segment to look for and
outputs the RC address resource. Use PNP0C02 devices to describe such RC
address resource. Use _UID to match segment to tell which root bus the
PNP0C02 resource belongs to.
[bhelgaas: add dev argument, wrap in #ifdef CONFIG_PCI_QUIRKS]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_std_update_resource() only deals with standard BARs, so we don't have
to worry about the complications of VF BARs in an SR-IOV capability.
Compute the BAR address inline and remove pci_resource_bar(). That makes
pci_iov_resource_bar() unused, so remove that as well.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Previously pci_update_resource() used the same code path for updating
standard BARs and VF BARs in SR-IOV capabilities.
Split the VF BAR update into a new pci_iov_update_resource() internal
interface, which makes it simpler to compute the BAR address (we can get
rid of pci_resource_bar() and pci_iov_resource_bar()).
This patch:
- Renames pci_update_resource() to pci_std_update_resource(),
- Adds pci_iov_update_resource(),
- Makes pci_update_resource() a wrapper that calls the appropriate one,
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Currently pcie_portdrv_probe() activates runtime PM on a PCIe port even
if it will never actually suspend because the BIOS is too old or the
"pcie_port_pm=off" option was specified on the kernel command line.
A few CPU cycles can be saved by not activating runtime PM at all in these
cases, because rpm_idle() and rpm_suspend() will bail out right at the
beginning when calling rpm_check_suspend_allowed(), instead of carrying out
various locking and assignments, invoking rpm_callback(), getting back
-EBUSY and rolling everything back.
The conditions checked in pci_bridge_d3_possible() are all static, they
never change during uptime of the system, hence it's safe to call this to
determine if runtime PM should be activated.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The algorithm to update the flag indicating whether a bridge may go to D3
makes a few optimizations based on whether the update was caused by the
removal of a device on the one hand, versus the addition of a device or the
change of its D3cold flags on the other hand.
The information whether the update pertains to a removal is currently
passed in by the caller, but the function may as well determine that itself
by examining the device in question, thereby allowing for a considerable
simplification and reduction of the code.
Out of several options to determine removal, I've chosen the function
device_is_registered() because it's cheap: It merely returns the
dev->kobj.state_in_sysfs flag. That flag is set through device_add() when
the root bus is scanned and cleared through device_remove(). The call to
pci_bridge_d3_update() happens after each of these calls, respectively, so
the ordering is correct.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/pm:
PCI: Avoid unnecessary resume after direct-complete
PCI: Recognize D3cold in pci_update_current_state()
PCI: Query platform firmware for device power state
PCI: Afford direct-complete to devices with non-standard PM
Bjorn Helgaas