To support peer-to-peer traffic on a segment of the PCI hierarchy, we must
disable the ACS redirect bits for select PCI bridges. The bridges must be
selected before the devices are discovered by the kernel and the IOMMU
groups created. Therefore, add a kernel command line parameter to specify
devices which must have their ACS bits disabled.
The new parameter takes a list of devices separated by a semicolon. Each
device specified will have its ACS redirect bits disabled. This is
similar to the existing 'resource_alignment' parameter.
The ACS Request P2P Request Redirect, P2P Completion Redirect and P2P
Egress Control bits are disabled, which is sufficient to always allow
passing P2P traffic uninterrupted. The bits are set after the kernel
(optionally) enables the ACS bits itself. It is also done regardless of
whether the kernel or platform firmware sets the bits.
If the user tries to disable the ACS redirect for a device without the ACS
capability, print a warning to dmesg.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: reorder to add the generic code first and move the
device-specific quirk to subsequent patches]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
When specifying PCI devices on the kernel command line using a
bus/device/function address, bus numbers can change when adding or
replacing a device, changing motherboard firmware, or applying kernel
parameters like "pci=assign-buses". When bus numbers change, it's likely
the command line tweak will be applied to the wrong device.
Therefore, it is useful to be able to specify devices with a base bus
number and the path of devfns needed to get to it, similar to the "device
scope" structure in the Intel VT-d spec, Section 8.3.1.
Thus, we add an option to specify devices in the following format:
[<domain>:]<bus>:<device>.<func>[/<device>.<func>]*
The path can be any segment within the PCI hierarchy of any length and
determined through the use of 'lspci -t'. When specified this way, it is
less likely that a renumbered bus will result in a valid device
specification and the tweak won't be applied to the wrong device.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: use "device" instead of "slot" in documentation since that's the
usual language in the PCI specs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Separate out the code to match a PCI device with a string (typically
originating from a kernel parameter) from the
pci_specified_resource_alignment() function into its own helper function.
While we are at it, this change fixes the kernel style of the function
(fixing a number of long lines and extra parentheses).
Additionally, make the analogous change to the kernel parameter
documentation: Separate the description of how to specify a PCI device
into its own section at the head of the "pci=" parameter.
This patch should have no functional alterations.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: use "device" instead of "slot" in documentation since that's the
usual language in the PCI specs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
-----BEGIN PGP SIGNATURE-----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=aFAi
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- unify AER decoding for native and ACPI CPER sources (Alexandru
Gagniuc)
- add TLP header info to AER tracepoint (Thomas Tai)
- add generic pcie_wait_for_link() interface (Oza Pawandeep)
- handle AER ERR_FATAL by removing and re-enumerating devices, as
Downstream Port Containment does (Oza Pawandeep)
- factor out common code between AER and DPC recovery (Oza Pawandeep)
- stop triggering DPC for ERR_NONFATAL errors (Oza Pawandeep)
- share ERR_FATAL recovery path between AER and DPC (Oza Pawandeep)
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
- clear interrupt status in top half to avoid interrupt storm (Oza
Pawandeep)
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn
Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use
ACPI hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
- fix an SHPC quirk that mistakenly included *all* AMD bridges as well
as devices from any vendor with device ID 0x7458 (Bjorn Helgaas)
- assign a bus number even to non-native hotplug bridges to leave
space for acpiphp additions, to fix a common Thunderbolt xHCI
hot-add failure (Mika Westerberg)
- keep acpiphp from scanning native hotplug bridges, to fix common
Thunderbolt hot-add failures (Mika Westerberg)
- improve "partially hidden behind bridge" messages from core (Mika
Westerberg)
- add macros for PCIe Link Control 2 register (Frederick Lawler)
- replace IB/hfi1 custom macros with PCI core versions (Frederick
Lawler)
- remove dead microblaze and xtensa code (Bjorn Helgaas)
- use dev_printk() when possible in xtensa and mips (Bjorn Helgaas)
- remove unused pcie_port_acpi_setup() and portdrv_acpi.c (Bjorn
Helgaas)
- add managed interface to get PCI host bridge resources from OF (Jan
Kiszka)
- add support for unbinding generic PCI host controller (Jan Kiszka)
- fix memory leaks when unbinding generic PCI host controller (Jan
Kiszka)
- request legacy VGA framebuffer only for VGA devices to avoid false
device conflicts (Bjorn Helgaas)
- turn on PCI_COMMAND_IO & PCI_COMMAND_MEMORY in pci_enable_device()
like everybody else, not in pcibios_fixup_bus() (Bjorn Helgaas)
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
- enable register clock for Armada 7K/8K (Gregory CLEMENT)
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo
Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
- fix DesignWare enumeration below bridges (Koen Vandeputte)
- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
- update Layerscape maintainer email addresses (Minghuan Lian)
- add COMPILE_TEST to improve build test coverage (Rob Herring)
- fix Hyper-V bus registration failure caused by domain/serial number
confusion (Sridhar Pitchai)
- improve Hyper-V refcounting and coding style (Stephen Hemminger)
- avoid potential Hyper-V hang waiting for a response that will never
come (Dexuan Cui)
- implement Mediatek chained IRQ handling (Honghui Zhang)
- fix vendor ID & class type for Mediatek MT7622 (Honghui Zhang)
- add Mobiveil PCIe host controller driver (Subrahmanya Lingappa)
- add Mobiveil MSI support (Subrahmanya Lingappa)
- clean up clocks, MSI, IRQ mappings in R-Car probe failure paths
(Marek Vasut)
- poll more frequently (5us vs 5ms) while waiting for R-Car data link
active (Marek Vasut)
- use generic OF parsing interface in R-Car (Vladimir Zapolskiy)
- add R-Car V3H (R8A77980) "compatible" string (Sergei Shtylyov)
- add R-Car gen3 PHY support (Sergei Shtylyov)
- improve R-Car PHYRDY polling (Sergei Shtylyov)
- clean up R-Car macros (Marek Vasut)
- use runtime PM for R-Car controller clock (Dien Pham)
- update arm64 defconfig for Rockchip (Shawn Lin)
- refactor Rockchip code to facilitate both root port and endpoint
mode (Shawn Lin)
- add Rockchip endpoint mode driver (Shawn Lin)
- support VMD "membar shadow" feature (Jon Derrick)
- support VMD bus number offsets (Jon Derrick)
- add VMD "no AER source ID" quirk for more device IDs (Jon Derrick)
- remove unnecessary host controller CONFIG_PCIEPORTBUS Kconfig
selections (Bjorn Helgaas)
- clean up quirks.c organization and whitespace (Bjorn Helgaas)
* tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (144 commits)
PCI/AER: Replace struct pcie_device with pci_dev
PCI/AER: Remove unused parameters
PCI: qcom: Include gpio/consumer.h
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: mobiveil: Add MSI support
PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver
PCI/AER: Decode Error Source Requester ID
PCI/AER: Remove aer_recover_work_func() forward declaration
PCI/DPC: Use the generic pcie_do_fatal_recovery() path
PCI/AER: Pass service type to pcie_do_fatal_recovery()
PCI/DPC: Disable ERR_NONFATAL handling by DPC
...
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
* pci/virtualization:
PCI/IOV: Allow PF drivers to limit total_VFs to 0
PCI: Add "pci=noats" boot parameter
PCI: Add ACS quirk for Intel 300 series
PCI: Add ACS quirk for Intel 7th & 8th Gen mobile
nvme-pci: Use pci_sriov_configure_simple() to enable VFs
net: ena: Use pci_sriov_configure_simple() to enable VFs
PCI/IOV: Add pci-pf-stub driver for PFs that only enable VFs
PCI/IOV: Add pci_sriov_configure_simple()
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
* pci/enumeration:
PCI: Remove unused pcie_get_minimum_link()
ixgbe: Report PCIe link properties with pcie_print_link_status()
cxgb4: Report PCIe link properties with pcie_print_link_status()
bnxt_en: Report PCIe link properties with pcie_print_link_status()
bnx2x: Report PCIe link properties with pcie_print_link_status()
PCI: Prevent sysfs disable of device while driver is attached
PCI: Check whether bridges allow access to extended config space
x86/PCI: Make pci=earlydump output neat
In some cases pcie_get_minimum_link() returned misleading information
because it found the slowest link and the narrowest link without
considering the total bandwidth of the link.
For example, consider a path with these two links:
- 16.0 GT/s x1 link (16.0 * 10^9 * 128 / 130) * 1 / 8 = 1969 MB/s
- 2.5 GT/s x16 link ( 2.5 * 10^9 * 8 / 10) * 16 / 8 = 4000 MB/s
The available bandwidth of the path is limited by the 16 GT/s link to about
1969 MB/s, but pcie_get_minimum_link() returned 2.5 GT/s x1, which
corresponds to only 250 MB/s.
Callers should use pcie_print_link_status() instead, or
pcie_bandwidth_available() if they need more detailed information.
Remove pcie_get_minimum_link() since there are no callers left.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Two comments in pci_target_state() are outdated, as the function
doesn't set the target power state for the device any more, only
finds one for it, so fix them accordingly.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Clients such as hotplug and Downstream Port Containment (DPC) both need to
wait until a link becomes active or inactive.
Add a generic pcie_wait_link_active() interface and use it instead of
duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The only user of pci_get_new_domain_nr() is of_pci_bus_find_domain_nr().
Since they are defined in the same file, pci_get_new_domain_nr() can be
made static, which also simplifies preprocessor conditionals.
No functional change intended.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Adds a "pci=noats" boot parameter. When supplied, all ATS related
functions fail immediately and the IOMMU is configured to not use
device-IOTLB.
Any function that checks for ATS capabilities directly against the devices
should also check this flag. Currently, such functions exist only in IOMMU
drivers, and they are covered by this patch.
The motivation behind this patch is the existence of malicious devices.
Lots of research has been done about how to use the IOMMU as protection
from such devices. When ATS is supported, any I/O device can access any
physical address by faking device-IOTLB entries. Adding the ability to
ignore these entries lets sysadmins enhance system security.
Signed-off-by: Gil Kupfer <gilkup@cs.technion.ac.il>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Commit 0847684cfc (PCI / PM: Simplify device wakeup settings code)
went too far and dropped the device_may_wakeup() check from
pci_enable_wake() which causes wakeup to be enabled during system
suspend, hibernation or shutdown for some PCI devices that are not
allowed by user space to wake up the system from sleep (or power off).
As a result of this, excessive power is drawn by some of the affected
systems while in sleep states or off.
Restore the device_may_wakeup() check in pci_enable_wake(), but make
sure that the PCI bus type's runtime suspend callback will not call
device_may_wakeup() which is about system wakeup from sleep and not
about device wakeup from runtime suspend.
Fixes: 0847684cfc (PCI / PM: Simplify device wakeup settings code)
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
USB controller ASM1042 stops working after commit de3ef1eb1c (PM /
core: Drop run_wake flag from struct dev_pm_info).
The device in question is not power managed by platform firmware,
furthermore, it only supports PME# from D3cold:
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Before commit de3ef1eb1c, the device never gets runtime suspended.
After that commit, the device gets runtime suspended to D3hot, which can
not generate any PME#.
usb_hcd_pci_probe() unconditionally calls device_wakeup_enable(), hence
device_can_wakeup() in pci_dev_run_wake() always returns true.
So pci_dev_run_wake() needs to check PME wakeup capability as its first
condition.
In addition, change wakeup flag passed to pci_target_state() from false
to true, because we want to find the deepest state different from D3cold
that the device can still generate PME#. In this case, it's D0 for the
device in question.
Fixes: de3ef1eb1c (PM / core: Drop run_wake flag from struct dev_pm_info)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the pcie_print_link_status() will print PCIe bandwidth and link
width information but does not mention it is pertaining to the PCIe. Since
this and related functions are used exclusively by networking drivers today
users may get confused into thinking that it's the NIC bandwidth that is
being talked about. Insert a "PCIe" into the messages.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When reassigning device resources to increase their alignment, e.g.,
because of a "pci=resource_alignment=" kernel parameter or because the
platform aligns resources to its page size, we previously emitted messages
like this:
pci 0000:00:00.0: Disabling memory decoding and releasing memory resources
pci 0000:00:00.0: disabling bridge mem windows
These messages don't convey any useful information, so remove them.
Fixes: 3827463769 ("powerpc/powernv: Override pcibios_default_alignment() to force PCI devices to be page aligned")
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization (KarimAllah
Ahmed)
* pci/virtualization:
PCI/IOV: Add missing prototypes for powerpc pcibios interfaces
PCI/IOV: Use VF0 cached config registers for other VFs
PCI/IOV: Skip BAR sizing for VFs
PCI/IOV: Skip INTx config reads for VFs
PCI: Wait for device to become ready after secondary bus reset
PCI: Add a return type for pci_reset_bridge_secondary_bus()
PCI: Wait for device to become ready after a power management reset
PCI: Rename pci_flr_wait() to pci_dev_wait() and make it generic
PCI: Handle FLR failure and allow other reset types
PCI: Protect restore with device lock to be consistent
PCI: Add function 1 DMA alias quirk for Marvell 88SE9220
PCI: Add ACS quirk for Ampere root ports
PCI: Remove redundant probes for device reset support
PCI: Probe for device reset support during enumeration
Conflicts:
include/linux/pci.h
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
* pci/misc:
PCI: Always define the of_node helpers
PCI: Tidy comments
PCI: Tidy Makefiles
mcb: Add Altera PCI ID to mcb-pci
PCI: Add Altera vendor ID
PCI: Report quirks that take more than 10ms
PCI: Report quirk timings with pci_info() instead of pr_debug()
PCI: Fix NULL pointer dereference in of_pci_bus_find_domain_nr()
rapidio/tsi721: use PCI_EXP_DEVCTL2_COMP_TIMEOUT macro
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space (Zhichang Yuan)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
* pci/lpc:
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
lib: Add generic PIO mapping method
After introducing the new generic I/O space management (Logical PIO), the
original PCI MMIO relevant helpers need to be updated based on the new
interfaces defined in logical PIO.
Adapt the corresponding code to match the changes introduced by logical
PIO.
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Zhichang Yuan <yuanzhichang@hisilicon.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de> # earlier draft
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
In preparation for having the PCI MMIO helpers use the new generic I/O
space management (logical PIO) we need to add the fwnode handler as an
extra input parameter.
Changes the signature of pci_register_io_range() and its callers as
needed.
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
pci_register_io_range() has only one definition, so there is no need for
the __weak attribute. Remove it.
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Add pcie_print_link_status(). This logs the current settings of the link
(speed, width, and total available bandwidth).
If the device is capable of more bandwidth but is limited by a slower
upstream link, we include information about the link that limits the
device's performance.
The user may be able to move the device to a different slot for better
performance.
This provides a unified method for all PCI devices to report status and
issues, instead of each device reporting in a different way, using
different code.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: changelog, reword log messages, print device capabilities when
not limited, print bandwidth in Gb/s]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pcie_bandwidth_available() to compute the bandwidth available to a
device. This may be limited by the device itself or by a slower upstream
link leading to the device.
The available bandwidth at each link along the path is computed as:
link_width * link_speed * (1 - encoding_overhead)
2.5 and 5.0 GT/s links use 8b/10b encoding, which reduces the raw bandwidth
available by 20%; 8.0 GT/s and faster links use 128b/130b encoding, which
reduces it by about 1.5%.
The result is in Mb/s, i.e., megabits/second, of raw bandwidth.
Also return the device with the slowest link and the speed and width of
that link.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: changelog, leave pcie_get_minimum_link() alone for now, return
bw directly, use pci_upstream_bridge(), check "next_bw <= bw" to find
uppermost limiting device, return speed/width of the limiting device]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle were:
- Add "Jailhouse" hypervisor support (Jan Kiszka)
- Update DeviceTree support (Ivan Gorinov)
- Improve DMI date handling (Andy Shevchenko)"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/PCI: Fix a potential regression when using dmi_get_bios_year()
firmware/dmi_scan: Uninline dmi_get_bios_year() helper
x86/devicetree: Use CPU description from Device Tree
of/Documentation: Specify local APIC ID in "reg"
MAINTAINERS: Add entry for Jailhouse
x86/jailhouse: Allow to use PCI_MMCONFIG without ACPI
x86: Consolidate PCI_MMCONFIG configs
x86: Align x86_64 PCI_MMCONFIG with 32-bit variant
x86/jailhouse: Enable PCI mmconfig access in inmates
PCI: Scan all functions when running over Jailhouse
jailhouse: Provide detection for non-x86 systems
x86/devicetree: Fix device IRQ settings in DT
x86/devicetree: Initialize device tree before using it
pci: Simplify code by using the new dmi_get_bios_year() helper
ACPI/sleep: Simplify code by using the new dmi_get_bios_year() helper
x86/pci: Simplify code by using the new dmi_get_bios_year() helper
dmi: Introduce the dmi_get_bios_year() helper function
x86/platform/quark: Re-use DEFINE_SHOW_ATTRIBUTE() macro
x86/platform/atom: Re-use DEFINE_SHOW_ATTRIBUTE() macro
Add pcie_bandwidth_capable() to compute the max link bandwidth supported by
a device, based on the max link speed and width, adjusted by the encoding
overhead.
The maximum bandwidth of the link is computed as:
max_link_width * max_link_speed * (1 - encoding_overhead)
2.5 and 5.0 GT/s links use 8b/10b encoding, which reduces the raw bandwidth
available by 20%; 8.0 GT/s and faster links use 128b/130b encoding, which
reduces it by about 1.5%.
The result is in Mb/s, i.e., megabits/second, of raw bandwidth.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: add 16 GT/s, adjust for pcie_get_speed_cap() and
pcie_get_width_cap() signatures, don't export outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pcie_get_width_cap() to find the max link width supported by a device.
Change max_link_width_show() to use pcie_get_width_cap().
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: return width directly instead of error and *width, don't export
outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Add pcie_get_speed_cap() to find the max link speed supported by a device.
Change max_link_speed_show() to use pcie_get_speed_cap().
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: return speed directly instead of error and *speed, don't export
outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are PCI devices which are power-manageable by a nonstandard means,
such as a custom ACPI method. One example are discrete GPUs in hybrid
graphics laptops, another are Thunderbolt controllers in Macs.
Such devices can't be put into D3cold with pci_set_power_state() because
pci_platform_power_transition() fails with -ENODEV. Instead they're put
into D3hot by pci_set_power_state() and subsequently into D3cold by
invoking the nonstandard means. However as a consequence the cached
current_state is incorrectly left at D3hot.
What we need to do is walk the hierarchy below such a PCI device on
powerdown and update the current_state to D3cold. On powerup the PCI
device itself and the hierarchy below it is in D0uninitialized, so we
need to walk the hierarchy again and wake all devices, causing them to
be put into D0active and then letting them autosuspend as they see fit.
To this end make pci_wakeup_bus() & pci_bus_set_current_state() public
so PCI drivers don't have to reinvent the wheel.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/2962443259e7faec577274b4ef8c54aad66f9a94.1520068884.git.lukas@wunner.de
Move pcie_clear_root_pme_status() from the port driver to the PCI core so
it will be available even when the port driver isn't present. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Setting Secondary Bus Reset of a downstream port sends a hot reset. PCIe
r4.0, sec 2.3.1, Request Handling Rules, indicates that a device can return
CRS Completion Status following such a reset. Wait until the device
becomes ready in that situation.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Add a return value to pci_reset_bridge_secondary_bus() so we can return an
error if the device doesn't become ready after the reset.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
PCIe r4.0, sec 2.3.1, Request Handling Rules, indicates that a device can
return CRS Completion Status following a D3hot to D0 transition. Wait
until the device becomes ready in that situation.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
If the "parent" pointer passed to of_pci_bus_find_domain_nr() is NULL,
don't dereference it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe r4.0, sec 2.3.1, Request Handling Rules, says:
Valid reset conditions after which a device is permitted to return CRS
are:
* Cold, Warm, and Hot Resets,
* FLR
* A reset initiated in response to a D3hot to D0 uninitialized
Try to reuse FLR implementation towards other reset types.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_flr_wait() and pci_af_flr() functions assume graceful return even
though the device is inaccessible under error conditions.
Return -ENOTTY in error cases so that __pci_reset_function_locked() can
try other reset types if AF_FLR/FLR reset fails.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Commit b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify() usage
with device_lock()") added protection around pci_dev_restore() function so
a device-specific remove callback does not cause a race condition with
hotplug.
pci_dev_lock() usage has been forgotten in two places. Add locks for
pci_slot_restore() and moving pci_dev_restore() inside the locks for
pci_try_reset_function().
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
...instead of open coding its functionality.
No changes in functionality.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-acpi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20180222125923.57385-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We probe every device for whether it supports reset so we can tell whether
to create a sysfs "reset" file for it. We do that probe in
pci_init_capabilities() during enumeration and save the result in
dev->reset_fn. The result doesn't depend on any other devices on the bus
and shouldn't change after boot, so we don't need to do the probe again.
Remove the pci_probe_reset_function() calls and rely on the dev->reset_fn
we found during enumeration. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
* pci/spdx:
PCI: Add SPDX GPL-2.0+ to replace implicit GPL v2 or later statement
PCI: Add SPDX GPL-2.0+ to replace GPL v2 or later boilerplate
PCI: Add SPDX GPL-2.0 to replace COPYING boilerplate
PCI: Add SPDX GPL-2.0 to replace GPL v2 boilerplate
PCI: Add SPDX GPL-2.0 when no license was specified
* pci/misc:
PCI: Add dummy pci_irqd_intx_xlate() for CONFIG_PCI=n build
PCI: Add wrappers for dev_printk()
PCI: Remove unnecessary messages for memory allocation failures
PCI: Add #defines for Completion Timeout Disable feature
hinic: Replace PCI pool old API
net: e100: Replace PCI pool old API
block: DAC960: Replace PCI pool old API
MAINTAINERS: Include more PCI files
PCI: Remove unneeded kallsyms include
powerpc/pci: Unroll two pass loop when scanning bridges
powerpc/pci: Use for_each_pci_bridge() helper
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Atomic Operations feature (PCIe r4.0, sec 6.15) allows atomic
transctions to be requested by, routed through and completed by PCIe
components. Routing and completion do not require software support.
Component support for each is detectable via the DEVCAP2 register.
A Requester may use AtomicOps only if its PCI_EXP_DEVCTL2_ATOMIC_REQ is
set. This should be set only if the Completer and all intermediate routing
elements support AtomicOps.
A concrete example is the AMD Fiji-class GPU (which is capable of making
AtomicOp requests), below a PLX 8747 switch (advertising AtomicOp routing)
with a Haswell host bridge (advertising AtomicOp completion support).
Add pci_enable_atomic_ops_to_root() for per-device control over AtomicOp
requests. This checks to be sure the Root Port supports completion of the
desired AtomicOp sizes and the path to the Root Port supports routing the
AtomicOps.
Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
[bhelgaas: changelog, comments, whitespace]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add PCI-specific dev_printk() wrappers and use them to simplify the code
slightly. No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: squash into one patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pcim_set_mwi(), a device-managed version of pci_set_mwi().
First user is the Realtek r8169 driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logan Gunthorpe