This moves the cfg80211 specific stuff to new cfg80211 debugfs
entries. Non-mac80211 will also get these entries now. There were
only 4 which we take:
rts_threshold
fragmentation_threshold
short_retry_limit
long_retry_limit
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to nl80211 userspace can be very specific upon device
configuration. Before processing the request for the new HT40
channel types (HT40- or HT40+) we need to ensure we can use them
regulatory-wise. This wasn't required with wireless extensions as
specifying the channel type wasn't not available and configuration
was done towards the end implicitly upon association or reception
of beacons from the AP. For the new nl80211 we have to check this
when configuring the interfaces explicitly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more consistent with our nl80211 naming convention
for HT40-/+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are not correctly listening to the regulatory max bandwidth
settings. To actually make use of it we need to redesign things
a bit. This patch does the work for that. We do this to so we
can obey to regulatory rules accordingly for use of HT40.
We end up dealing with HT40 by having two passes for each channel.
The first check will see if a 20 MHz channel fits into the channel's
center freq on a given frequency range. We check for a 20 MHz
banwidth channel as that is the maximum an individual channel
will use, at least for now. The first pass will go ahead and
check if the regulatory rule for that given center of frequency
allows 40 MHz bandwidths and we use this to determine whether
or not the channel supports HT40 or not. So to support HT40 you'll
need at a regulatory rule that allows you to use 40 MHz channels
but you're channel must also be enabled and support 20 MHz by itself.
The second pass is done after we do the regulatory checks over
an device's supported channel list. On each channel we'll check
if the control channel and the extension both:
o exist
o are enabled
o regulatory allows 40 MHz bandwidth on its frequency range
This work allows allows us to idependently check for HT40- and
HT40+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its possible for cfg80211 to have scheduled the work and for
the global workqueue to not have kicked in prior to a cfg80211
driver's regulatory hint or wiphy_apply_custom_regulatory().
Although this is very unlikely its possible and should fix
this race. When this race would happen you are expected to have
hit a null pointer dereference panic.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another design flaw in wireless extensions (is anybody
surprised?) in the way it handles the iw_encode_ext
structure: The structure is part of the 'extra' memory
but contains the key length explicitly, instead of it
just being the length of the extra buffer - size of
the struct and using the explicit key length only for
the get operation (which only writes it).
Therefore, we have this layout:
extra: +-------------------------+
| struct iw_encode_ext { |
| ... |
| u16 key_len; |
| u8 key[0]; |
| }; |
+-------------------------+
| key material |
+-------------------------+
Now, all drivers I checked use ext->key_len without
checking that both key_len and the struct fit into the
extra buffer that has been copied from userspace. This
leads to a buffer overrun while reading that buffer,
depending on the driver it may be possible to specify
arbitrary key_len or it may need to be a proper length
for the key algorithm specified.
Thankfully, this is only exploitable by root, but root
can actually cause a segfault or use kernel memory as
a key (which you can even get back with siocgiwencode
or siocgiwencodeext from the key buffer).
Fix this by verifying that key_len fits into the buffer
along with struct iw_encode_ext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nlmsg_new() adds the size of the netlink header to the value
that has been passed as parameter. If NLMSG_GOODSIZE is selected,
we request an allocation of one memory page plus the size of the
header. Instead, NLMSG_DEFAULT_SIZE should be used since it
already substracts the size of the Netlink header.
I have the impression that the similar naming in both constant
is error prone when using it with nlmsg_new(). This is already
documented in include/net/netlink.h
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though they are true, they cause sparse to complain
because it doesn't see the __acquires(dev_base_lock) on
dev_seq_start() because it is only added to the function
in net/core/dev.c, not the header file. To keep track of
the nesting correctly we should probably annotate those
functions publically, but for now let's just remove the
annotation I added to wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting a key with NL80211_CMD_NEW_KEY, we should allow the key
sequence number (RSC) to be set in order to allow replay protection to
work correctly for group keys. This patch documents this use for
nl80211 and adds the couple of missing pieces in nl80211/cfg80211 and
mac80211 to support this. In addition, WEXT SIOCSIWENCODEEXT compat
processing in cfg80211 is extended to handle the RSC (this was already
specified in WEXT, but just not implemented in cfg80211/mac80211).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new NL80211_ATTR_CONTROL_PORT flag for NL80211_CMD_ASSOCIATE to
allow user space to indicate that it will control the IEEE 802.1X port
in station mode. Previously, mac80211 was always marking the port
authorized in station mode. This was enough when drop_unencrypted flag
was set. However, drop_unencrypted can currently be controlled only
with WEXT and the current nl80211 design does not allow fully secure
configuration. Fix this by providing a mechanism for user space to
control the IEEE 802.1X port in station mode (i.e., do the same that
we are already doing in AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is currently not possible to modify station flags, but that
capability would be very useful. This patch introduces a new
nl80211 attribute that contains a set/mask for station flags,
and updates the internal API (and mac80211) to mirror that.
The new attribute is parsed before falling back to the old so
that userspace can specify both (if it can) to work on all
kernels.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_STA_FLAG_MFP was forgotten from sta_flags_policy. The previous
version added the flag due to the loop used in parse_station_flags,
but the proper behavior would be to allow nla_parse_nested() to go
through the policy for all flags.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move key handling wireless extension ioctls from mac80211 to cfg80211
so that all drivers that implement the cfg80211 operations get wext
compatibility.
Note that this drops the SIOCGIWENCODE ioctl support for getting
IW_ENCODE_RESTRICTED/IW_ENCODE_OPEN. This means that iwconfig will
no longer report "Security mode:open" or "Security mode:restricted"
for mac80211. However, what we displayed there (the authentication
algo used) was actually wrong -- linux/wireless.h states that this
setting is meant to differentiate between "Refuse non-encoded packets"
and "Accept non-encoded packets".
(Combined with "cfg80211: fix a couple of bugs with key ioctls". -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, get_wireless_stats is racy by _design_. This is
because it returns a buffer, which needs to be statically
allocated since it cannot be freed if it was allocated
dynamically. Also, SIOCGIWSTATS and /proc/net/wireless use
no common lock, and /proc/net/wireless accesses are not
synchronised against each other. This is a design flaw in
get_wireless_stats since the beginning.
This patch fixes it by wrapping /proc/net/wireless accesses
with the RTNL so they are protected against each other and
SIOCGIWSTATS. The more correct method of fixing this would
be to pass in the buffer instead of returning it and have
the caller take care of synchronisation of the buffer, but
even then most drivers probably assume that their callback
is protected by the RTNL like all other wext callbacks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make it more apparent in the code what is for wext
only (and needs to be #ifdef'ed) put all the info for
wext into a substruct in each wireless_dev.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function to parse a struct iw_freq has a stupid bug,
it returns NULL when the channel cannot be found at all,
but NULL is supposed to mean "auto". Fix this by checking
the return value of ieee80211_get_channel() and returning
ERR_PTR(-EINVAL) if it returned NULL (channel not found).
This fixes an issue where you could say (in IBSS mode)
iwconfig wlan0 channel 21
and it would use channel 1 instead because that's the
first available channel with IBSS allowed (which is what
the "auto" setting uses).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_CMD_ASSOCIATE request must be able to indicate whether
management frame protection (IEEE 802.11w) is being used. mac80211 was
able to use MFP in client mode only with WEXT, but the new
NL80211_ATTR_USE_MFP attribute will allow this to be done with
nl80211, too.
Since we are currently using nl80211 for MFP only with drivers that
use user space SME, only MFP disabled and required values are
used. However, the NL80211_ATTR_USE_MFP attribute is an enum that can
be extended with MFP optional in the future, if that is needed with
some drivers (e.g., if the RSN IE is generated by the driver).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse complaint:
CHECK net/wireless/nl80211.c
net/wireless/nl80211.c:3694:6:
warning: symbol 'nl80211_send_mlme_timeout'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IE buffer was allocated, the pub.information_elements pointer
was also changed to the allocated space. So we must not assume anymore
that the pointer points at the "found" tail.
So if it was allocated previously, take the codebranch that grows the
buffer size (if necessary) and put the data into the allocated buffer.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes an unnecessary ksize() call. krealloc() will do this
test internally and won't perform any allocation if the space is
already sufficient to hold the data.
So remove the redundant check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0ad8acaf "cfg80211: fix NULL pointer deference in
reg_device_remove()" added a check that last_request is non-NULL,
rendering the 2nd check superfluous. While there, rearrange the code a
bit so it's a little more straight forward.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to lock using the cfg80211_mutex in
wiphy_apply_custom_regulatory(). Without the lock
there is possible race between processing a reply from CRDA
and a driver calling wiphy_apply_custom_regulatory(). During
the processing of the reply from CRDA we free last_request and
wiphy_apply_custom_regulatory() eventually accesses an
element from last_request in the through freq_reg_info_regd().
This is very difficult to reproduce (I haven't), it takes us
3 hours and you need to be banging hard, but the race is obvious
by looking at the code.
This should only affect those who use this caller, which currently
is ath5k, ath9k, and ar9170.
EIP: 0060:[<f8ebec50>] EFLAGS: 00210282 CPU: 1
EIP is at freq_reg_info_regd+0x24/0x121 [cfg80211]
EAX: 00000000 EBX: f7ca0060 ECX: f5183d94 EDX: 0024cde0
ESI: f8f56edc EDI: 00000000 EBP: 00000000 ESP: f5183d44
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process modprobe (pid: 14617, ti=f5182000 task=f3934d10 task.ti=f5182000)
Stack: c0505300 f7ca0ab4 f5183d94 0024cde0 f8f403a6 f8f63160 f7ca0060 00000000
00000000 f8ebedf8 f5183d90 f8f56edc 00000000 00000004 00000f40 f8f56edc
f7ca0060 f7ca1234 00000000 00000000 00000000 f7ca14f0 f7ca0ab4 f7ca1289
Call Trace:
[<f8ebedf8>] wiphy_apply_custom_regulatory+0x8f/0x122 [cfg80211]
[<f8f3f798>] ath_attach+0x707/0x9e6 [ath9k]
[<f8f45e46>] ath_pci_probe+0x18d/0x29a [ath9k]
[<c023c7ba>] pci_device_probe+0xa3/0xe4
[<c02a860b>] really_probe+0xd7/0x1de
[<c02a87e7>] __driver_attach+0x37/0x55
[<c02a7eed>] bus_for_each_dev+0x31/0x57
[<c02a83bd>] driver_attach+0x16/0x18
[<c02a78e6>] bus_add_driver+0xec/0x21b
[<c02a8959>] driver_register+0x85/0xe2
[<c023c9bb>] __pci_register_driver+0x3c/0x69
[<f8e93043>] ath9k_init+0x43/0x68 [ath9k]
[<c010112b>] _stext+0x3b/0x116
[<c014a872>] sys_init_module+0x8a/0x19e
[<c01049ad>] sysenter_do_call+0x12/0x21
[<ffffe430>] 0xffffe430
=======================
Code: 0f 94 c0 c3 31 c0 c3 55 57 56 53 89 c3 83 ec 14 8b 74 24 2c 89 54 24 0c 89 4c 24 08 85 f6 75
06 8b 35 c8 bb ec f8 a1 cc bb ec f8 <8b> 40 04 83 f8 03 74 3a 48 74 37 8b 43 28 85 c0 74 30 89 c6
8b
EIP: [<f8ebec50>] freq_reg_info_regd+0x24/0x121 [cfg80211] SS:ESP 0068:f5183d44
Cc: stable@kernel.org
Reported-by: Nataraj Sadasivam <Nataraj.Sadasivam@Atheros.com>
Reported-by: Vivek Natarajan <Vivek.Natarajan@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another bug in the "cfg80211: do not replace BSS structs" patch,
a forgotten length update leads to bogus data being stored and
passed to userspace, often truncated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SME needs to be notified when the authentication or association
attempt times out and MLME has stopped processing in order to allow
the SME to decide what to do next.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the JOIN_IBSS command look at the beacon interval
attribute to see if the user requested a specific beacon
interval, if not default to 100 TU (wext too).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fact that these are exported is a technical detail
of the conversion period -- we don't want anybody to
start relying on these. Ultimately we want things to
use cfg80211 only, and once everything that is in wext
is converted to cfg80211 drivers will not need to touch
wext _at all_.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we leave an IBSS, we should clear the SSID and not just the
BSSID, but since WEXT allows configuring while the interface is
down we must not clear it when leaving due to taking the iface
down, so some complications are needed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.
The "new" net/cfg80211.h is now divided into sections.
There are no real changes in this patch but code shuffling
and some very minor documentation fixes.
I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds IBSS API along with (preliminary) wext handlers.
The wext handlers can only do IBSS so you need to call them
from your own wext handlers if the mode is IBSS.
The nl80211 API requires
* an SSID
* a channel (frequency) for the case that a new IBSS
has to be created
It optionally supports
* a flag to fix the channel
* a fixed BSSID
The cfg80211 code also takes care to leave the IBSS before
the netdev is set down. If wireless extensions are used, it
also caches values when the interface is down and instructs
the driver to join when the interface is set up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have ->deauth and ->disassoc we can support the
wext SIWMLME call directly without driver wext handlers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When listing all wireless netdevs in the system this
is useful to print which wiphy they belong to. Just
add the attribute, any program that doesn't care will
just ignore it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That will make the various cases where the WARN_ON
can happen distinguishable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary code and fields to let drivers specify
their cipher capabilities and exports them to userspace. Also
update mac80211 to export the ciphers it has.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This informs userspace when a change has occured on a world
roaming wiphy's channel which has lifted some restrictions
due to a regulatory beacon hint.
Because this is now sent to userspace through the regulatory
multicast group we remove the debug prints we used to use as
they are no longer necessary.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a netlink channel put helper, nl80211_msg_put_channel(),
which we will also make use of later for the beacon hints events.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of our documented API we always respect the orig_flag
settings on a channel. We forgot to follow this for the beacon
hints.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of just passing the cfg80211-requested IEs, pass
the locally generated ones as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added cfg80211_inform_bss() for full-mac devices to use.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define a new nl80211 event, NL80211_CMD_MICHAEL_MIC_FAILURE, to be
used to notify user space about locally detected Michael MIC failures.
This matches with the MLME-MICHAELMICFAILURE.indication() primitive.
Since we do not actually have TSC in the skb anymore when
mac80211_ev_michael_mic_failure() is called, that function is changed
to take in the TSC as an optional parameter instead of as a
requirement to include the TSC after the hdr field (which we did not
really follow). For now, TSC is not included in the events from
mac80211, but it could be added at some point.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, nl80211 mlme events were generated only for received
deauthentication and disassociation frames. We need to do the same for
locally generated ones in order to let applications know that we
disconnected (e.g., when AP does not reply to a probe). Rename the
nl80211 and cfg80211 functions (s/rx_//) to make it clearer that they
are used for both received and locally generated frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_ATTR_AUTH_TYPE is a required parameter for
NL80211_CMD_AUTHENTICATE. We are currently (by chance) defaulting to
open system authentication if the attribute is not specified. It is
better to just reject the invalid command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove duplicated #include in net/wireless/core.h.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes nl80211 to:
* validate that any IE input is a valid IE (stream)
* move some validation code before locking
* require that a reason code is given for both deauth/disassoc
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the code paths sending deauth/disassoc events ends up calling
this function with rcu_read_lock held, so we must use GFP_ATOMIC in
allocation routines.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead, allocate extra IE memory if necessary. Normally,
this isn't even necessary since there's enough space.
This is a better way of correcting the "held BSS can
disappear" issue, but also a lot more code. It is also
necessary for proper auth/assoc BSS handling in the
future.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive a probe response frame we can replace the
BSS struct in our list -- but if that struct is held then
we need to hold the new one as well.
We really should fix this completely and not replace the
struct, but this is a bandaid for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We won't ever get here as regulatory_hint_core() can only fail
on -ENOMEM and in that case we don't initialize cfg80211 but this is
technically correct code.
This is actually good for stable, where we don't check for -ENOMEM
failure on __regulatory_hint()'s failure.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And update description and feature-removal schedule according
to the new plan.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reports that there's a circular locking dependency;
this is because cfg80211_dev_rename() will acquire the
cfg80211_mutex while the device mutex is held, while
this normally is done the other way around. The solution
is to open-code the device-getting in nl80211_set_wiphy
and require holding the mutex around cfg80211_dev_rename
rather than acquiring it within.
Also fix a bug -- rtnl locking is expected by drivers so
we need to provide it.
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In beacon filtering there needs to be a way to not expire the BSS even
when no beacons are received. Add an interface to cfg80211 to hold
BSS and make sure that it's not expired.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When somebody tries to set the interface mode to the existing
mode, don't ask the driver but silently accept the setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We had left in code to allow interested developers to add
support for parsing country IEs when OLD_REG was enabled.
This never happened and since we're going to remove OLD_REG
lets just remove these comments and code for it.
This code path was never being entered so this has no
functional change.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems a few users are using this module parameter although its not
recommended. People are finding it useful despite there being utilities
for setting this in userspace. I'm not aware of any distribution using
this though.
Until userspace and distributions catch up with a default userspace
automatic replacement (GeoClue integration would be nirvana) we copy
the ieee80211_regdom module parameter from OLD_REG to the new reg
code to help these users migrate.
Users who are using the non-valid ISO / IEC 3166 alpha "EU" in their
ieee80211_regdom module parameter and migrate to non-OLD_REG enabled
system will world roam.
This also schedules removal of this same ieee80211_regdom module
parameter circa March 2010. Hope is by then nirvana is reached and
users will abandoned the module parameter completely.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The incorrect assumption is the last regulatory request
(last_request) is always a country IE when processing
country IEs. Although this is true 99% of the time the
first time this happens this could not be true.
This fixes an oops in the branch check for the last_request
when accessing drv_last_ie. The access was done under the
assumption the struct won't be null.
Note to stable: to port to 29 replace as follows, only 29 has
country IE code:
s|NL80211_REGDOM_SET_BY_COUNTRY_IE|REGDOM_SET_BY_COUNTRY_IE
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although EU is a bogus alpha2 we need to process the send request
as our code depends on last_request being set.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this. In addition, make the error values consistent by using
EOPNOTSUPP instead of semi-random assortment of errno values.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this or to be prepared to handle these commands when the interface is
down.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check that the used authentication type and reason code are valid here
so that drivers/mac80211 do not need to care about this. In addition,
remove the unnecessary validation of SSID attribute length which is
taken care of by netlink policy.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.
Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new nl80211 commands to allow user space to request
authentication and association (and also deauthentication and
disassociation). The commands are structured to allow separate
authentication and association steps, i.e., the interface between
kernel and user space is similar to the MLME SAP interface in IEEE
802.11 standard and an user space application takes the role of the
SME.
The patch introduces MLME-AUTHENTICATE.request,
MLME-{,RE}ASSOCIATE.request, MLME-DEAUTHENTICATE.request, and
MLME-DISASSOCIATE.request primitives. The authentication and
association commands request the actual operations in two steps
(assuming the driver supports this; if not, separate authentication
step is skipped; this could end up being a separate "connect"
command).
The initial implementation for mac80211 uses the current
net/mac80211/mlme.c for actual sending and processing of management
frames and the new nl80211 commands will just stop the current state
machine from moving automatically from authentication to association.
Future cleanup may move more of the MLME operations into cfg80211.
The goal of this design is to provide more control of authentication and
association process to user space without having to move the full MLME
implementation. This should be enough to allow IEEE 802.11r FT protocol
and 802.11s SAE authentication to be implemented. Obviously, this will
also bring the extra benefit of not having to use WEXT for association
requests with mac80211. An example implementation of a user space SME
using the new nl80211 commands is available for wpa_supplicant.
This patch is enough to get IEEE 802.11r FT protocol working with
over-the-air mechanism (over-the-DS will need additional MLME
primitives for handling the FT Action frames).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 event notifications (and a new multicast group, "mlme")
for informing user space about received and processed Authentication,
(Re)Association Response, Deauthentication, and Disassociation frames in
station and IBSS modes (i.e., MLME SAP interface primitives
MLME-AUTHENTICATE.confirm, MLME-ASSOCIATE.confirm,
MLME-REASSOCIATE.confirm, MLME-DEAUTHENTICATE.indicate, and
MLME-DISASSOCIATE.indication). The event data is encapsulated as the 802.11
management frame since we already have the frame in that format and it
includes all the needed information.
This is the initial step in providing MLME SAP interface for
authentication and association with nl80211. In other words, kernel code
will act as the MLME and a user space application can control it as the
SME.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added scanning to cfg80211, we got a lock dependency like this:
rtnl --> cfg80211_mtx
nl80211, on the other hand, has the reverse lock dependency:
cfg80211_mtx --> rtnl
which clearly is a bad idea. This patch reworks nl80211 to take these
two locks in the other order to fix the possible, and easily
triggerable, deadlock.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes nl80211 export the supported commands (command groups)
per wiphy so userspace has an idea what it can do -- this will be
required reading for userspace when we introduce auth/assoc /or/
connect for older hardware that cannot separate auth and assoc.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan capability added to cfg80211/nl80211 introduced a
dependency on nl80211 by cfg80211. We can thus no longer have
just cfg80211 without nl80211. Specifically, cfg80211_scan_done()
calls nl80211_send_scan_aborted() or nl80211_send_scan_done().
Now we remove the option for user to select nl80211. It will always
be compiled if user selects cfg80211.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_CMD_GET_MESH_PARAMS and NL80211_CMD_SET_MESH_PARAMS handlers
did not verify whether a function pointer is NULL (not supported by
the driver) before trying to call the function. The former nl80211
command is available for unprivileged users, too, so this can
potentially allow normal users to kill networking (or worse..) if
mac80211 is built without CONFIG_MAC80211_MESH=y.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to send to userspace "regulatory" events.
For now we just send an event when we change regulatory domains.
We also notify userspace when devices are using their own custom
world roaming regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the lowest value amongst countries which do enable 5 GHz operation.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When they were part of the now defunct ieee80211 component, these
messages were only visible when special debugging settings were enabled.
Let's mirror that with a new lib80211 debugging Kconfig option.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
freq_diff is unsigned, so test before subtraction
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: add assert_cfg80211_lock() to ensure proper protection"
added assert_cfg80211_lock() calls into various places. At least
one of them, nl80211_send_wiphy(), should not have been there. That
triggers the BUG_ON in assert_cfg80211_lock() and pretty much kills
the kernel whenever someone runs hostapd.. Remove that call and make
assert_cfg80211_lock() use WARN_ON instead of BUG_ON to be a bit more
friendly to users.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we already have a regulatory request from the workqueue use that
and avoid a new kzalloc()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were passing value by value, lets just pass the struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When devices are world roaming they cannot beacon or do active scan
on 5 GHz or on channels 12, 13 and 14 on the 2 GHz band. Although
we have a good regulatory API some cards may _always_ world roam, this
is also true when a system does not have CRDA present. Devices doing world
roaming can still passive scan, if they find a beacon from an AP on
one of the world roaming frequencies we make the assumption we can do
the same and we also remove the passive scan requirement.
This adds support for providing beacon regulatory hints based on scans.
This works for devices that do either hardware or software scanning.
If a channel has not yet been marked as having had a beacon present
on it we queue the beacon hint processing into the workqueue.
All wireless devices will benefit from beacon regulatory hints from
any wireless device on a system including new devices connected to
the system at a later time.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current static world regulatory domain is too restrictive,
we can use some 5 GHz channels world wide so long as they do not
touch frequencies which require DFS. The compromise is we must
also enforce passive scanning and disallow usage of a mode of
operation that beacons: (AP | IBSS | Mesh)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables active scan and beaconing on Channels 1 through 11
on the static world regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers that agree on regulatory to share their
regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was never happening but it was still wrong, so correct it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Truth of the matter this was confusing people so mark it as
unlikely as that is the case now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not protecting last_request there is a small possible race
between an 11d hint and another routine which calls reset_regdomains()
which can prevent a valid country IE from being processed. This is
not critical as it will still be procesed soon after but locking prior
to it is correct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so later on we can move the pending requests onto a
workqueue. By using the wiphy_idx instead of the wiphy we can
later easily check if the wiphy has disappeared or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling kobject_uevent_env() can fail mainly due to out of
memory conditions. We do not want to continue during such
conditions so propagate that as well instead of letting
cfg80211 load as if everything is peachy.
Additionally lets clarify that when CRDA is not called during
cfg80211's initialization _and_ if the error is not an -ENOMEM
its because kobject_uevent_env() failed to call CRDA, not because
CRDA failed. For those who want to find out why we also let you
do so by enabling the kernel config CONFIG_CFG80211_REG_DEBUG --
you'll get an actual stack trace.
So for now we'll treat non -ENOMEM kobject_uevent_env() failures as
non fatal during cfg80211's initialization.
CC: Greg KH <greg@kroah.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the core hint path more readable and allows for us to
later make it obvious under what circumstances we need locking or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 is built into the kernel there is perhaps a small
time window betwen nl80211_init() and regulatory_init() where
cfg80211_regdomain hasn't yet been initialized to let the
wireless core do its work. During that rare case and time
frame (if its even possible) we don't allow user regulatory
changes as cfg80211 is working on enabling its first regulatory
domain.
To check for cfg80211_regdomain we now contend the entire operation
using the cfg80211_mutex.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_drv_mutex is protecting more than the driver list,
this renames it and documents what its currently supposed to
protect.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will later be used by others, for now make use of it in
cfg80211_drv_by_wiphy_idx() to return early if an invalid
wiphy_idx has been provided.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makes it clearer to read when comparing to ifidx
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous patch made cfg80211 generally aware of the signal
type a given hardware will give, so now it can implement
SIOCGIWRANGE itself, removing more wext stuff from mac80211.
Might need to be a little more parametrized once we have
more hardware using cfg80211 and new hardware capabilities.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It wasn't a good idea to make the signal type a per-BSS option,
although then it is closer to the actual value. Move it to be
a per-wiphy setting, update mac80211 to match.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no particular reason to not let untrusted users see
this information -- it's just the stations we're talking to,
packet counters for them and possibly some mesh things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to various bugs in the software stack we end up having
to fill qual.qual; level should be used, but wpa_supplicant
doesn't properly ignore qual.qual, NM should use qual.level
regardless of that because qual.qual is 0 but doesn't handle
IW_QUAL_DBM right now.
So fill qual.qual with the qual.level value clamped to
-110..-40 dBm or just the regular 'unspecified' signal level.
This requires a mac80211 change to properly announce the
max_qual.qual and avg_qual.qual values.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanned BSS entries are timestamped with jiffies, which doesn't
increment across suspend and hibernate. On resume, every BSS in the
scan list looks like it was scanned within the last 10 seconds,
irregardless of how long the machine was actually asleep. Age scan
results on resume with the time spent during sleep so userspace has a
clue how old they really are.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX packet counters are needed to fill in RADIUS Accounting
attributes Acct-Output-Packets and Acct-Input-Packets. We already
collect the needed information, but only the TX/RX bytes were
previously exposed through nl80211. Allow applications to fetch the
packet counters, too, to provide more complete support for accounting.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This extends the NL80211_CMD_TRIGGER_SCAN command to allow applications
to specify a set of information element(s) to be added into Probe
Request frames with NL80211_ATTR_IE. This provides support for the
MLME-SCAN.request primitive parameter VendorSpecificInfo and can be
used, e.g., to implement WPS scanning.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add empty function for case of CONFIG_NL80211=n:
net/wireless/scan.c:35: error: implicit declaration of function 'nl80211_send_scan_aborted'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a more flexible BSS lookup function so that mac80211 or
other drivers can actually use this for getting the BSS to
connect to.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces cfg80211_unlink_bss, a function to
allow a driver to remove a BSS from the internal list and
make it not show up in scan results any more -- this is
to be used when the driver detects that the BSS is no
longer available.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cfg80211 users have their own allocated data in the per-BSS
private data, they will need to free this when the BSS struct is
destroyed. Add a free_priv method and fix one place where the BSS
was kfree'd rather than released properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds basic scan capability to cfg80211/nl80211 and
changes mac80211 to use it. The BSS list that cfg80211 maintains
is made driver-accessible with a private area in each BSS struct,
but mac80211 doesn't yet use it. That's another large project.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets userspace request to get the currently set
regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the regulatory domain is already set it is technically not an error
so do not pass an errno to userspace.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let users be more compliant if so desired.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to request strict regulatory settings to
be applied to its devices. This is desirable for devices where
proper calibration and compliance can only be gauranteed for
for the device's programmed regulatory domain. Regulatory
domain settings will be ignored until the device's own
regulatory domain is properly configured. If no regulatory
domain is received only the world regulatory domain will be
applied -- if OLD_REG (default to "US") is not enabled. If
OLD_REG behaviour is not acceptable to drivers they must
update their wiphy with a custom reuglatory prior to wiphy
registration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers may need more information than just who set the last regulatory domain,
as such lets just pass the last regulatory_request receipt. To do this we need
to move out to headers struct regulatory_request, and enum environment_cap. While
at it lets add documentation for enum environment_cap.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that the initial REGDOM_SET_BY_CORE upon wiphy registration
respects the wiphy->custom_regulatory setting. Without this and if OLD_REG
is disabled (which will be default soon as we remove it) the
wiphy->custom_regulatory is simply ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers without firmware can also have custom regulatory maps
which do not map to a specific ISO / IEC alpha2 country code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We ignore regulatory hints for the same alpha2 if we already
have processed the same alpha2 on the current regulatory domain.
For a driver regulatory_hint() this means we copy onto its
wiphy->regd the previously procesed regulatory domain from CRDA
without having to call CRDA again.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents user regulatory changes to be considered prior to previous
pending user, core or driver requests which have not be applied.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used by drivers on the reg_notifier()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds wiphy_apply_custom_regulatory() to be used by drivers
prior to wiphy registration to apply a custom regulatory domain.
This can be used by drivers that do not have a direct 1-1 mapping
between a regulatory domain and a country.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help implement suspend/resume in mac80211, these
hooks will be run before the device is suspended and after it
resumes. Therefore, they can touch the hardware as much as
they want to.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new nl80211 command, NL80211_CMD_SET_MGMT_EXTRA_IE, can be used to
add arbitrary IE data into the end of management frames. The interface
allows extra IEs to be configured for each management frame subtype, but
only some of them (ProbeReq, ProbeResp, Auth, (Re)AssocReq, Deauth,
Disassoc) are currently accepted in mac80211 implementation.
This makes it easier to implement IEEE 802.11 extensions like WPS and
FT that add IE(s) into some management frames. In addition, this can
be useful for testing and experimentation purposes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the
TX/RX paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add support for multiple drivers to provide a regulatory_hint()
on a system by adding a wiphy specific regulatory domain cache.
This allows drivers to keep around cache their own regulatory domain
structure queried from CRDA.
We handle conflicts by intersecting multiple regulatory domains,
each driver will stick to its own regulatory domain though unless
a country IE has been received and processed.
If the user already requested a regulatory domain and a driver
requests the same regulatory domain then simply copy to the
driver's regd the same regulatory domain and do not call
CRDA, do not collect $200.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are calling the reg_notifier() callback per band, this is
not necessary, just call it once.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CONFIG_CFG80211_REG_DEBUG is enabled and an intersection
occurs we are printing the regulatory domain passed by CRDA
and indicating its the intersected regulatory domain. Lets fix
this and print the intersection as originally intended.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two issues with the sanity check loop when processing
the country IE:
1. Do not use frequency for the current subband channel check,
this was a big fat typo.
2. Apply the 5 GHz 4-channel steps when considering max channel
on each subband as was done with a recent patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The country IE number of channels on 5 GHz specifies the number
of 5 GHz channels, not the number of sequential channel numbers.
For example, if in a country IEs if the first channel given is 36
and the number of channels passed is 4 then the individual channel
numbers defined for the 5 GHz PHY by these parameters
are: 36, 40, 44, 48
not: 36, 37, 38, 39
See: http://tinyurl.com/11d-clarification
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression on disallowing bands introduced with the new
802.11d support. The issue is that IEEE-802.11 allows APs to send
a subset of what a country regulatory domain defines. This was clarified
in this document:
http://tinyurl.com/11d-clarification
As such it is possible, and this is what is done in practice, that a
single band 2.4 GHz AP will only send 2.4 GHz band regulatory information
through the 802.11 country information element and then the current
intersection with what CRDA provided yields a regulatory domain with
no 5 GHz information -- even though that country may actually allow
5 GHz operation. We correct this by only applying the intersection rules
on a channel if the the intersection yields a regulatory rule on the
same band the channel is on.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to make more wiphy specific judgements when
handling the channels later on.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.
Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds signal strength and transmission bitrate
to the station_info of nl80211.
Signed-off-by: Henning Rogge <rogge@fgan.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure sparse checks endianness when run on mac80211/cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix two small bugs with HT frequency setting:
* HT is accepted even when the driver is incapable
* HT40 is accepted when the driver cannot do 40 MHz
(both on the selected band)
Also simplify the code a little.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix incorrect use of loose in wext.c
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This "fixes" the 11d oops I was seeing. This needs some more work but I
cannot work on it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes the segfault I just pointed out.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
further reducing wext code in mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the SIOCGIWNAME handling from mac80211 to cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new NL80211_CMD_SET_WIPHY attributes
NL80211_ATTR_WIPHY_FREQ and NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET to allow
userspace to set the operating channel (e.g., hostapd for AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to be consistent with NL80211_ATTR_POWER_RULE_MAX_EIRP,
change NL80211_FREQUENCY_ATTR_MAX_TX_POWER to use mBm and U32 instead
of dBm and U8. This is a userspace interface change, but the previous
version had not yet been pushed upstream and there are no userspace
programs using this yet, so there is justification to get this change in
as long as it goes in before the previous version gets out.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is useful information to provide for userspace (e.g., hostapd needs
this to generate Country IE).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to cfg80211 to allow wireless drivers to inform
us if their firmware can handle regulatory considerations *and*
they cannot map these regulatory domains to an ISO / IEC 3166
alpha2. In these cases we skip the first regulatory hint instead
of expecting the driver to build their own regulatory structure,
providing us with an alpha2, or using the reg_notifier().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds country IE parsing to mac80211 and enables its usage
within the new regulatory infrastructure in cfg80211. We parse
the country IEs only on management beacons for the BSSID you are
associated to and disregard the IEs when the country and environment
(indoor, outdoor, any) matches the already processed country IE.
To avoid following misinformed or outdated APs we build and use
a regulatory domain out of the intersection between what the AP
provides us on the country IE and what CRDA is aware is allowed
on the same country.
A secondary device is allowed to follow only the same country IE
as it make no sense for two devices on a system to be in two
different countries.
In the case the AP is using country IEs for an incorrect country
the user may help compliance further by setting the regulatory
domain before or after the IE is parsed and in that case another
intersection will be performed.
CONFIG_WIRELESS_OLD_REGULATORY is supported but requires CRDA
present.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lets remain consistent and mark rds with > NL80211_MAX_SUPP_REG_RULES
number of reg rules as invalid in is_valid_rd().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kobject_uevent_env() can return an error but it just tells us
if the uvent was built/sent or not, it doesn't tell us anything
about what happened in userspace, whether the udev rule was present
nor does it tell us if CRDA was present or not. So remove
the informative complaint about it assuming it will tell us
such things.
Note that you can determine if CRDA is present after loading cfg80211
by using:
is_old_static_regdom(cfg80211_regdomain)
but this doesn't account for possible user install after initial
boot, and also for when the user uses the static EU regulatory
domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When intersecting it is possible that set_regdom() was called
with a regulatory domain which we'll only use as an aid to
build a final regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So far the __set_regdom() code is pretty generic as the
intersection case is fairly straight forward; this will however
change when 802.11d support is added so lets separate intersection
code for now in preparation for 802.11d support.
This patch only has slight functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have control over the REGDOM_SET_BY_* macros passed
so remove the switch.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have complete control over REGDOM_SET_BY_* enum passed
down to __regulatory_hint() as such there is no need to
account for unexpected REGDOM_SET_BY_*'s, lets just remove
the switch statement as this code does not change and
won't change even when we add 802.11d support.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regulatory rules with negative frequencies are now
marked as invalid in is_valid_reg_rule().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove converting the MAC address to a string by a direct byte
conversion and use %pM instead, since the code is now boilerplate
use a macro to define the show functions, and also use the shorter
__ATTR_RO macro to define the attributes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These bits are shared already between ipw2x00 and hostap, and could
probably be shared both more cleanly and with other drivers. This
commit simply relocates the code to lib80211 and adjusts the drivers
appropriately.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As regulatory_request gets bigger there will be more questions
of what things means, so clarify documenation for it and
keep track of the special alpha2 codes we use internally
and on the userspace regulatory agents.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are certain scenerios where we require intersecting
two regulatory domains. This adds intersection support.
When we enable 802.11d support we will use this to intersect
the regulatory domain from the AP's country IE and what our
regulatory agent believes is correct for a country.
This patch enables intersection for now in the case where
the last regdomain was set by a country IE which was parsed
and the user then wants to set the regulatory domain. Since
we don't support country IE parsing yet this code path will not
be hit, however this allows us to pave the way for 11d support.
Intersection code has been tested in userspace with CRDA.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A regulatory rule is invalid when the frequency difference
between the end of the frequency range and the start is 0.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_WIPHY_TXQ_PARAMS, that can be used with
NL80211_CMD_SET_WIPHY for userspace (e.g., hostapd) to set TX queue
parameters (txop, cwmin, cwmax, aifs).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_BSS_BASIC_RATES, that can be used with
NL80211_CMD_SET_BSS for userspace (e.g., hostapd) to set which rates are
in the basic rate set.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a helper function that, given a bitmap of basic
rates and a bitrate returns the response rate for this rate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is only used once, move it closer to its caller.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function has a few WARNs that may eventually trigger
when an AP sends rogue beacons, those must be removed. Some
of the comments in the function are also inappropriate as
this function is concerned with the global hint, not a per-
wiphy thing (which a multidomain flag on a wiphy would imply).
I'm convinced that we don't need to do anything to implement
multi-domain capability as 802.11-2007 specifies it because
it makes only two things mandatory:
* starting of BSS/IBSS must have country information
(this can easily be done with a mac80211 patch)
* a STA must adopt the country information (we already have
the framework for this)
But we don't have anything implemented anyway for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code needs to be split out and cleaned up, so as a
first step remove the capability, to add it back in a
subsequent patch as a separate function. Also remove the
publically facing return value of the function and the
wiphy argument. A number of internal functions go from
being generic helpers to just being used for alpha2
setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The regdom struct is given to the core, so it might as well
free it in error conditions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unnecessary and of questionable value. Also remove
is_empty_ssid, as it is also unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We really only need to know the last request at each point in time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This mutex is wrong, we use cfg80211_drv_mutex (which should
possibly be renamed to just cfg80211_mutex) everywhere except
in one place, fix that and get rid of the extra mutex.
Also get rid of a spurious regulatory_requests list definition.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function requires an internal lock to be held, so it cannot
be published to other modules in the kernel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two new commands are NL80211_CMD_GET_MESH_PARAMS and
NL80211_CMD_SET_MESH_PARAMS. There is a new attribute enum,
NL80211_ATTR_MESH_PARAMS, which enumerates the various mesh configuration
parameters.
Moved struct mesh_config from mac80211/ieee80211_i.h to net/cfg80211.h.
nl80211_get_mesh_params and nl80211_set_mesh_params unpack the netlink messages
and ask the driver to get or set the configuration. This is done via two new
function stubs, get_mesh_params and set_mesh_params, in struct cfg80211_ops.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NLA_NESTED attributes cannot be empty, but we want to be able to
specify "no flags" (empty attribute) vs. "no change" (no attribute).
Therefore, remove the NLA_NESTED policy so it can work as an empty
attribute.
I guess I should have used a u32 for these flags instead, but we're
stuck with it now. Haven't noticed earlier because of a bug in iw...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This exports the local HT capabilities in nl80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default for the regulatory compatibility option is wrong;
if you picked the default you ended up with a non-functional wifi
system (at least I did on Fedora 9 with iwl4965).
I don't think even the October 2008 releases of the various distros
has the new userland so clearly the default is wrong, and also
we can't just go about deleting this in 2.6.29...
Change the default to "y" and also adjust the config text a little to
reflect this.
This patch fixes regression #11859
With thanks to Johannes Berg for the diagnostics
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If something goes wrong creating the debugfs dir or when
debugfs is not compiled in, the current code might lead to
trouble; make it more robust.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed duplicated include <linux/list.h> in
net/wireless/core.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two improvements in this simple patch:
1. wiphy_counter is a static var only used in one function, so
can use local static instead of global static;
2. wiphy_counter wrap handling killed one comparision;
Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reject configuring mesh-id for non-mesh, monitor flags for non-monitor.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes cfg80211 show the interface in the nl80211
information about a specific interface. API users are required
to keep the type updated (everything else is fairly complicated)
but you will get a warning if you fail to keep it updated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The statically defined regdomains are used in a very convoluted
way, use them instead to prime the information we have and then
continue operating normally.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few pointers and structures in the regulatory code are const,
but because it wasn't done properly a whole bunch of bogus
casts were needed to compile without warning. Mark everything
const properly to avoid that kind of junk code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent code from Luis is an #ifdef hell and contains lots of
code that's stuffed into the wrong file making a whole bunch of
things needlessly non-static, and besides, what is it doing in
core.c??
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When Luis added the static regdomains back he used +/-20
of the centre frequencies to account for 40MHz bandwidth
neglecting the fact that 40MHz bandwidth cannot be used
on the channels close to the allowed band edges.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new wireless regulatory infrastructure. The
main motiviation behind this was to centralize regulatory
code as each driver was implementing their own regulatory solution,
and to replace the initial centralized code we have where:
* only 3 regulatory domains are supported: US, JP and EU
* regulatory domains can only be changed through module parameter
* all rules were built statically in the kernel
We now have support for regulatory domains for many countries
and regulatory domains are now queried through a userspace agent
through udev allowing distributions to update regulatory rules
without updating the kernel.
Each driver can regulatory_hint() a regulatory domain
based on either their EEPROM mapped regulatory domain value to a
respective ISO/IEC 3166-1 country code or pass an internally built
regulatory domain. We also add support to let the user set the
regulatory domain through userspace in case of faulty EEPROMs to
further help compliance.
Support for world roaming will be added soon for cards capable of
this.
For more information see:
http://wireless.kernel.org/en/developers/Regulatory/CRDA
For now we leave an option to enable the old module parameter,
ieee80211_regdom, and to build the 3 old regdomains statically
(US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY.
These old static definitions and the module parameter is being
scheduled for removal for 2.6.29. Note that if you use this
you won't make use of a world regulatory domain as its pointless.
If you leave this option enabled and if CRDA is present and you
use US or JP we will try to ask CRDA to update us a regulatory
domain for us.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current setup with hal and NetworkManager will fail to work
without newest hal version with this config option disabled.
Although this will solve itself by time, at the moment it is
dishonest to say that we don't know any software that uses it,
if there are many many people relying on old hal versions.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace (e.g., hostapd) to set HT capabilities for associated
STAs. This is based on a patch from Zhu Yi <yi.zhu@intel.com> (only
the NL80211_ATTR_HT_CAPABILITY for NEW_STA part is included here).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change adds a new cfg80211 command, NL80211_CMD_SET_BSS, to allow
AP mode BSS parameters to be changed from user space (e.g., hostapd).
The drivers using mac80211 are expected to be modified with separate
changes to use the new BSS info parameter for short slot time in the
bss_info_changed() handler.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the minimal the wireless extensions oughta send at least
the name in addition to the ifindex.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julius Volz pointed out that the dump callbacks in nl80211 were
broken and fixed one of them. This patch fixes the other three
and also addresses the TODOs there.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Julius Volz <juliusv@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without CONFIG_NET_NS, namespace is always &init_net.
Compiler will be able to omit namespace comparisons with this patch.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The /sys/class/net/*/wireless/ direcory is, as far as I know, not
used by anyone. Additionally, the same data is available via wext
ioctls. Hence the sysfs files are pretty much useless. This patch
makes them optional and schedules them for removal.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although I only tested similar code (I don't use any of this wireless
code), the state maintainance between Netlink dump callback invocations
seems wrong here and should lead to an endless loop. There are also other
examples in the same file which might have the same problem. Perhaps someone
can actually test this (or refute my logic).
Take the simple example with only one element in the list (which should fit
into the message):
1. invocation:
Start:
idx = 0, start = 0
Loop:
condition (++idx < start) => (1 < 0) => false
=> no continue, fill one entry, exit loop, return skb->len > 0
2. invocation:
Start:
idx = 0, start = 1
Loop:
condition (++idx < start) => (1 < 1) => false
=> no continue, fill the same entry again, exit loop, return skb->len > 0
3. invocation:
Same as 2. invocation, endless invocation of callback.
Also, iterations where the filling of an element fails should not be counted as
completed, so idx should not be incremented in this case.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Next we can kill the hacks in fs/compat_ioctl.c and also
dispatch compat ioctls down into the driver and 80211 protocol
helper layers in order to handle iw_point objects embedded in
stream replies which need to be translated.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement missing EU regulatory domain for mac80211. Based on the
information in IEEE 802.11-2007 (specifically pages 1142, 1143 & 1148)
and ETSI 301 893 (V1.4.1).
With thanks to Johannes Berg.
Signed-off-by: Tony Vroon <tony@linx.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make nlmsg_trim(), nlmsg_cancel(), genlmsg_cancel(), and
nla_nest_cancel() void functions.
Return -EMSGSIZE instead of -1 if the provided message buffer is not
big enough.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
device_rename only performs useful and race free validity
checking at the optional sysfs level so depending on it
for all of the validity checking in cfg80211_dev_rename
is racy.
Instead implement all of the needed validity checking
and locking in cfg80211_dev_rename.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the STA AID setting and actually makes hostapd/mac80211
work properly in presence of power-saving stations.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes ieee80211_get_channel a static inline defined in
cfg80211's header file which simply calls __ieee80211_get_channel
to avoid symbol clashes with the ieee80211 code.
The problem was pointed out by David Miller, thanks!
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ieee80211_get_channel() which gets you a channel struct for a
specific wiphy if that channel is present in that wiphy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Added support for mesh id and mesh path operation as well as
station structure dumping.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds channels to US regulatory domain
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows precise control over what a monitor interface shows.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver registers a IEEE80211_BAND_2GHZ band,
it can either be 802.11b or 802.11g. But when 802.11b rates
are registered "want" will be 3 (since 4 rates are being registered,
and each of those 4 rates will decrease "want").
Since this is a correct situation, there is no need to trigger
a WARN_ON() for this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the rate API patch I accidentally reverted the test for
ERP rates, this fixes it. All rates except 1, 2, 5.5 and 11
MBit are ERP rates, not those.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes nl80211 export the hardware bitrate/channel capabilities
as registered in a wiphy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As event_type_pk_size[] is not used, Remove it.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a station is added to the kernel's structures, userspace
has to be able to retrieve statistics about that station, especially
whether the station was idle and how much bytes were transferred
to and from it. This adds the necessary code to nl80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds station handling to cfg80211/nl80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary API to cfg80211/nl80211 to allow
changing beaconing settings.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces key handling to cfg80211/nl80211. Default
and group keys can be added, changed and removed; sequence
counters for each key can be retrieved.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this patch none of the netlink callback support anything
except the initial network namespace but the rtnetlink infrastructure
now handles multiple network namespaces.
Changes from v2:
- IPv6 addrlabel processing
Changes from v1:
- no need for special rtnl_unlock handling
- fixed IPv6 ndisc
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit systems sizeof(struct ifreq) is 8 bytes larger than
sizeof(struct iwreq).
For GET calls, the wireless extension code copies back into userspace
using sizeof(struct ifreq) but userspace and elsewhere only allocates
a "struct iwreq". Thus, this copy writes past the end of the iwreq
object and corrupts whatever sits after it in memory.
Fix the copy_to_user() length.
This particularly hurts the compat case because the wireless compat
code uses compat_alloc_userspace() and right after this allocated
buffer is the current bottom of the user stack, and that's what gets
overwritten by the copy_to_user() call.
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Seems that a bare "depends" is no longer allowed in Sam's kbuild tree.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem: proc_net files remember which network namespace the are
against but do not remember hold a reference count (as that would pin
the network namespace). So we currently have a small window where
the reference count on a network namespace may be incremented when opening
a /proc file when it has already gone to zero.
To fix this introduce maybe_get_net and get_proc_net.
maybe_get_net increments the network namespace reference count only if it is
greater then zero, ensuring we don't increment a reference count after it
has gone to zero.
get_proc_net handles all of the magic to go from a proc inode to the network
namespace instance and call maybe_get_net on it.
PROC_NET the old accessor is removed so that we don't get confused and use
the wrong helper function.
Then I fix up the callers to use get_proc_net and handle the case case
where get_proc_net returns NULL. In that case I return -ENXIO because
effectively the network namespace has already gone away so the files
we are trying to access don't exist anymore.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes /proc/net per network namespace. It modifies the global
variables proc_net and proc_net_stat to be per network namespace.
The proc_net file helpers are modified to take a network namespace argument,
and all of their callers are fixed to pass &init_net for that argument.
This ensures that all of the /proc/net files are only visible and
usable in the initial network namespace until the code behind them
has been updated to be handle multiple network namespaces.
Making /proc/net per namespace is necessary as at least some files
in /proc/net depend upon the set of network devices which is per
network namespace, and even more files in /proc/net have contents
that are relevant to a single network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the radiotap parser accept all other fields that are
currently defined.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makes use of the type safe netlink interface and adds a warning
if the message is too big for NLMSG_DEFAULT_SIZE to help debug.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cfg80211 is built into the kernel it needs to init earlier
so that device registrations are run after it has initialised.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/wireless/sysfs.c:108: warning: ‘wiphy_uevent’ defined but not used
when CONFIG_HOTPLUG=n is because the only usage site of this function
is #ifdef'ed as such, so let's #ifdef the definition also.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Generic code to walk through the fields in a radiotap header, accounting
for nasties like extended "field present" bitfields and alignment rules
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix signedness mixup making mac addresses show up strangely
(like 00:11:22:33:44:ffffffaa) in /sys/class/ieee80211/*/macaddress.
Signed-off-by: David Lamparter <equinox@diac24.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch clarifies the comment about locking in wiphy_unregister.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the locking in wiphy new. Ingo Oeser
<netdev@axxeo.de> noticed that locking in the error case was wrong and
also suggested this fix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just a few things that didn't fit in with the other patches.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a bunch of inline abuse from wext. Most functions
that were marked inline are only used once so the compiler will inline
them anyway, others are used multiple times but there's no requirement
for them to be inline since they aren't in any fast paths.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EXPORT_SYMBOL statements are supposed to go together with the symbol
they're exporting. This patch moves them accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the code in wireless_process_ioctl somewhat more
readable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch kills the two options in wext that are required to be
enabled anyway because they influence the userspace API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch kills a whole bunch of code that can only ever be used by
defining some things in wext.c. Also, the things that are printed are
mostly useless since the API is fairly well-tested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the call paths from the core code into wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves dev/core/wireless.c to net/wireless/wext.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As scheduled, this patch removes the pointless wext over netlink code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates the core cfg80211 code along with some sysfs bits.
This is a stripped down version to allow mac80211 to function, but
doesn't include any configuration yet except for creating and removing
virtual interfaces.
This patch includes the nl80211 header file but it only contains the
interface types which the cfg80211 interface for creating virtual
interfaces relies on.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the wireless Kconfig all over and already
introduces net/wireless/Kconfig with just the WEXT bit for now,
the cfg80211 patch will add to that as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luis R. Rodriguez