In native mode display all available staticstics.
In SRIOV mode on VF display only SW counters statistics,
in SRIOV mode on hypervisor display SW counters and errors (got from FW)
statistics.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.
2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
IB or Ethernet.
The driver will use this hint in case the user didn't specify explicitly the link layer
type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
and default the port to link sensing
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ConnectX3 devices, we allow link sensing only if FW explicitly
reported it supports the feature.
For older versions (ConnectX1 and 2), if the card supports both link layer types
(Ethenet and Infiniband), link sensing is supported.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added module parameters sr_iov and probe_vf for controlling enablement of
SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
ports configured as desired.
In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
for the case where the FW supports both port types (ETH and IB), the
port_type_array parameter is used.
By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
VFs obtain their startup information from the PF (master) device via the
comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership: Currently, only one PF is supported by the driver.
If the HCA is burned with FW which enables more than one PF, only one
of the PFs is allowed to run. The first one up grabs a FW ownership
semaphone -- all other PFs will find that semaphore taken, and the
driver will not allow them to run.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implementation mtts are managed by:
1. order - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order - log(mtts) rather than segments
2. offset - mtt index in mtt table
Note: The actual mtt allocation is made in segments but it is
transparent to callers.
Rational: The mtt resource holders are not interested on how the allocation
of mtt is done, but rather on how they will use it.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware
Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SRIOV is enabled on the chip (at FW burning time),
the HCA uses only 17 bits for the PD. The remaining 7 high-order bits
are ignored.
Change the allocator to return only 17 bits for the PD. The MSB 7
bits will be used to encode the slave number for consistency
checking later on in the resource tracker.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).
This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.
Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mask now has additional state.
Port can be set as "none". In this case neither the mlx4_en or mlx4_ib
drivers take ownership of the port.
In multifunction mode there is an option to set the vfs as single ported devices.
(in single function mode, both physical ports belong to same function)
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
These changes will not affect module operation as yet. They
are only to get some structs and enums in place for use by
subsequent patches (making those smaller).
Added here:
* sriov state structs and inlines (mlx4_is_master/slave/mfunc)
* comm-channel and vhcr support structures
* enum values for new FW and comm-channel virtual commands
(i.e., commands, passed via the comm channel to the PF-driver).
* prototypes for many command wrapper functions (used by the
PF context for processing FW commands passed to it by the VFs).
* struct mlx4_eqe is moved from eq.c to mlx4.h (it will be used
by other mlx4_core source files).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device must be in promiscuous mode or DMAC must be same as the host MAC, or
else packet will be dropped by the HW rx filtering.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 capability bits for WOL, one for each port.
WOL handlers were looking only on the second bit, regardless of the port.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Towards adding RSS support for IB drivers/application who use
the mlx4 HW, make the RSS related definitions global and change
the mlx4_en driver to use them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
An Extended Port Info packet is sent to each hw port during HCA init.
If it returns without error, we assume the port supports extended port
capabilities.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Canceling FCS removal where FW allows for better alignment
of incoming data.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the creation of XRC INI and TGT QPs. To handle the case where
a CQ or PD is not provided, we allocate them internally with the xrcd.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow the user to create XRC SRQs. This patch is based on a patch
from Jack Morgenstrein <jackm@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support creating and destroying XRC domains. Any sharing of the XRCD
is managed above the low-level driver.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allocate flow counter per Ethernet/IBoE port, and attach this counter
to all the QPs created on that port. Based on patch by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ConnectX devices support a set of flow counters that can be attached
to a set containing one or more QPs. Each such counter tracks receive
and transmit packets and bytes of these QPs. This patch queries the
device to check support for counters, handles initialization of the
HCA to enable counters, and initializes a bitmap allocator to control
counter allocations. Derived from patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the address handle portion of the QP context structure to have the
correct bit location for the counter index field.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Query another dword containing up to 32 extended device capabilities
and merge it into struct mlx4_caps.flags. Update the code that
handles the current extended device capabilities (e.g UDP RSS, WoL,
vep steering, etc) to use the extended device cap flags field instead
of a field per extended capability. Initial patch done by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The latest firmware adds a second dword containing more device flags,
so extend the device capabilities flags field from 32 to 64 bits.
Derived from patch by Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Using blue flame can improve latency by allowing the HW to more efficiently
access the WQE. This patch presents two functions that are used to allocate or
release HW resources for using blue flame; the caller need to supply a struct
mlx4_bf object when allocating resources. Consumers that make use of this API
should post doorbells to the UAR object pointed by the initialized struct
mlx4_bf;
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4_en module now uses the new steering mechanism.
The RX packets are now steered through the MCG table instead
of Mac table for unicast, and default entry for multicast.
The feature is enabled through INIT_HCA
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW revision is derived from device ID and rev id.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.
Signed-off-by: Igor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a pool of MSI-X vectors and EQs that can be used explicitly by mlx4_core
customers (mlx4_ib, mlx4_en). The consumers will assign their own names to the
interrupt vectors. Those vectors are not opened at mlx4 device initialization,
opened by demand.
Changed the max number of possible EQs according to the new scheme, no longer relies on
on number of cores.
The new functionality is exposed through mlx4_assign_eq() and mlx4_release_eq().
Customers that do not use the new API will get completion vectors as before.
Signed-off-by: Markuze Alex <markuze@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newest device firmware stores IB vs. Ethernet protocol in two bits
in members_count field of multicast group table (0: Infiniband, 1:
Ethernet). When changing the QP members count for a multicast group,
it important not to reset this information. When calling multicast
attach first time, the protocol type should be specified. In this
patch we always set it IB, but in the future we will handle Ethernet
too. When looking for a QP, the protocol type shoud be checked too.
Signed-off-by: Aleksey Senin <alekseys@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
IB/qib: Allow driver to load if PCIe AER fails
IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
IB/qib: Fix extra log level in qib_early_err()
RDMA/cxgb4: Remove unnecessary KERN_<level> use
RDMA/cxgb3: Remove unnecessary KERN_<level> use
IB/core: Add link layer type information to sysfs
IB/mlx4: Add VLAN support for IBoE
IB/core: Add VLAN support for IBoE
IB/mlx4: Add support for IBoE
mlx4_en: Change multicast promiscuous mode to support IBoE
mlx4_core: Update data structures and constants for IBoE
mlx4_core: Allow protocol drivers to find corresponding interfaces
IB/uverbs: Return link layer type to userspace for query port operation
IB/srp: Sync buffer before posting send
IB/srp: Use list_first_entry()
IB/srp: Reduce number of BUSY conditions
IB/srp: Eliminate two forward declarations
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
IB: Replace EXTRA_CFLAGS with ccflags-y
...
This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames. The VLAN tag is encoded in the GID and derived from it
by a simple computation.
The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IBoE to mlx4_ib. The bulk of the code is handling the
new address vector fields; mlx4 needs the MAC address of a remote node
to include it in a WQE (for datagrams) or in the QP context (for
connected QPs). Address resolution is done by assuming all unicast
GIDs are either link-local IPv6 addresses.
Multicast group attach/detach needs to update the NIC's multicast
filters; but since attaching a QP to a multicast group can be done
before the QP is bound to a port, for IBoE we need to keep track of
all multicast groups that a QP is attached too before it transitions
from INIT to RTR (since it does not have a port in the INIT state).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Many things cleaned up and otherwise monkeyed with; hope I didn't
introduce too many bugs. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add fields to hardware data structures and add new constants required for IBoE
support.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a mechanism for mlx4 protocol drivers to get a pointer to other
drivers's device objects. For this, an exported function,
mlx4_get_protocol_dev() is added, which allows a driver to get some
other driver's device based on the protocol that the driver
implements. Two protocols are added: MLX4_PROTOCOL_IB and
MLX4_PROTOCOL_EN.
This will be used in mlx4 IBoE support so that mlx4_ib can find the
corresponding mlx4_en netdev.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Clean up and rename a few things. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The Node Description cannot be changed via MADs (it is read-only).
Until now, it was changed in the driver via sysfs, and the new Node
Description was simply inserted by the driver into MAD responses
(replacing the description returned by FW).
System startup scripts use the sysfs interface to change the node
description at driver startup to show the hostname, etc. However, this
has a race condition: the SM could discover the original FW node
description rather than the system-specific description if it queried the
port before the startup scripts finish running.
For mlx4, we fix this with a new FW command (SET_NODE) that allows
passing the new node description to FW. When this command is invoked,
FW sends a trap 144 to the SM. When it gets this trap, the SM can
query the node to obtain the new node description -- thus eliminating
the effects of the race.
This patch simply calls SET_NODE command when a new node description
is entered via sysfs (thus causing trap 144 to be issued by the FW).
We ignore all failures of the SET_NODE command (including those caused
by using a device FW that predates the SET_NODE command), since in
that case things work just as before.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the limit on the size of max fast registration WRs that can be
posted to match hardware capabilities.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The report now based on query from FW, giving the correct tranciever type
and link speed.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for masked atomic operations (masked compare and swap,
masked fetch and add).
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary. This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size. The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length. Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ConnectX Programmer's Reference Manual states that the "SO" bit
must be set when posting Fast Register and Local Invalidate send work
requests. When this bit is set, the work request will be executed
only after all previous work requests on the send queue have been
executed. (If the bit is not set, Fast Register and Local Invalidate
WQEs may begin execution too early, which violates the defined
semantics for these operations)
This fixes the issue with NFS/RDMA reported in
<http://lists.openfabrics.org/pipermail/general/2009-April/059253.html>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current MTT allocator uses kmalloc() to allocate a buffer for its
buddy allocator, and thus is limited in the amount of MTT segments
that it can control. As a result, the size of memory that can be
registered is limited too. This patch uses a module parameter to
control the number of MTT entries that each segment represents,
allowing more memory to be registered with the same number of
segments.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a port's link is down (except to driver restart) and the port is
configured for auto sensing, we try to sense port link type (Ethernet
or InfiniBand) in order to determine how to initialize the port. If
the port type needs to be changed, all mlx4 for the device interfaces
are unregistered and then registered again with the new port
types. Sensing is done with intervals of 3 seconds.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When using MSI-X mode, create a completion event queue for each CPU.
Report the number of completion EQs in a new struct mlx4_caps member,
num_comp_vectors, and extend the mlx4_cq_alloc() interface with a
vector parameter so that consumers can specify which completion EQ
should be used to report events for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eugenia Emantayev