commit f606b3ef47 ("s390/pci: adapt events for zbus") removed the
zpci_disable_device() call for a zPCI event with PEC 0x0304 because
the device is already deconfigured by the platform.
This however skips the Linux side of the disable in particular it leads
to leaking the DMA tables and bitmaps because zpci_dma_exit_device() is
never called on the device.
If the device transitions to the Reserved state we call zpci_zdev_put()
but zpci_release_device() will not call zpci_disable_device() because
the state of the zPCI function is already ZPCI_FN_STATE_STANDBY.
If the device is put into the Standby state, zpci_disable_device() is
not called and the device is assumed to have been put in Standby through
platform action.
At this point the device may be removed by a subsequent event with PEC
0x0308 or 0x0306 which calls zpci_zdev_put() with the same problem
as above or the device may be configured again in which case
zpci_disable_device() is also not called.
Fix this by calling zpci_disable_device() explicitly for PEC 0x0304 as
before. To make it more clear that zpci_disable_device() may be called,
even if the lower level device has already been disabled by the
platform, add a comment to zpci_disable_device().
Cc: <stable@vger.kernel.org> # 5.8
Fixes: f606b3ef47 ("s390/pci: adapt events for zbus")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently there are four places in which a PCI function is scanned
and made available to drivers:
1. In pci_scan_root_bus() as part of the initial zbus
creation.
2. In zpci_bus_add_devices() when registering
a device in configured state on a zbus that has already been
scanned.
3. When a function is already known to zPCI (in reserved/standby state)
and configuration is triggered through firmware by PEC 0x301.
4. When a device is already known to zPCI (in standby/reserved state)
and configuration is triggered from within Linux using
enable_slot().
The PF/VF linking step and setting of pdev->is_virtfn introduced with
commit e5794cf1a2 ("s390/pci: create links between PFs and VFs") was
only triggered for the second case, which is where VFs created through
sriov_numvfs usually land. However unlike some other platforms but like
POWER VFs can be individually enabled/disabled through
/sys/bus/pci/slots.
Fix this by doing VF setup as part of pcibios_bus_add_device() which is
called in all of the above cases.
Finally to remove the PF/VF links call the common code
pci_iov_remove_virtfn() function to remove linked VFs.
This takes care of the necessary sysfs cleanup.
Fixes: e5794cf1a2 ("s390/pci: create links between PFs and VFs")
Cc: <stable@vger.kernel.org> # 5.8: 2f0230b2f2d5: s390/pci: re-introduce zpci_remove_device()
Cc: <stable@vger.kernel.org> # 5.8
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
For fixing the PF to VF link removal we need to perform some action on
every removal of a zdev from the common PCI subsystem.
So in preparation re-introduce zpci_remove_device() and use that instead
of directly calling the common code functions. This was actually still
declared from earlier code but no longer implemented.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
We were missing the pci_dev_put() for candidate PFs. Furhtermore in
discussion with upstream it turns out that somewhat counterintuitively
some common code, in particular the vfio-pci driver, assumes that
pdev->is_virtfn always implies that pdev->physfn is set, i.e. that VFs
are always linked.
While POWER does seem to set pdev->is_virtfn even for unlinked functions
(see comments in arch/powerpc/kernel/eeh.c:eeh_debugfs_break_device())
for now just be safe and only set pdev->is_virtfn on linking.
Also make sure that we only search for parent PFs if the zbus is
multifunction and we thus know the devfn values supplied by firmware
come from the RID.
Fixes: e5794cf1a2 ("s390/pci: create links between PFs and VFs")
Cc: <stable@vger.kernel.org> # 5.8
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
A configuration request event may be stale, that is the event
may reference a zdev which was already configured.
This can happen when a hotplug happens during boot such that
the device is discovered and configured in the initial clp_list_pci(),
then after initialization we enable events and process
the original configuration request which additionally still contains
the old disabled function handle leading to a failure during device
enablement and subsequent I/O lockout.
Fix this by restoring the check that the device to be configured is in
standby which was removed in commit f606b3ef47 ("s390/pci: adapt events
for zbus").
This check does not need serialization as we only enable the events after
zPCI has fully initialized, which includes the initial clp_list_pci(),
rescan only does updates and events are serialized with respect to each
other.
Fixes: f606b3ef47 ("s390/pci: adapt events for zbus")
Cc: <stable@vger.kernel.org> # 5.8
Reported-by: Shalini Chellathurai Saroja <shalini@linux.ibm.com>
Tested-by: Shalini Chellathurai Saroja <shalini@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
- Add support for custom exception handlers, as required by BPF_PROBE_MEM.
- Add support for BPF_PROBE_MEM.
- Add trace events for idle enter / exit for the s390 specific idle
implementation.
- Remove unused zcore memmmap device.
- Remove unused "raw view" from s390 debug feature.
- AP bus + zcrypt device driver code refactoring.
- Provide cex4 cca sysfs attributes for cex3 for zcrypt device driver.
- Expose only minimal interface to walk physmem for mm/memblock. This
is a common code change and it has been agreed on with Mike Rapoport
and Andrew Morton that this can go upstream via the s390 tree.
- Rework of the s390 vmem/vmmemap code to allow for future memory hot
remove.
- Get rid of FORCE_MAX_ZONEORDER to finally allow for order-10
allocations again, instead of only order-8 allocations.
- Various small improvements and fixes.
-----BEGIN PGP SIGNATURE-----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=H0KX
-----END PGP SIGNATURE-----
Merge tag 's390-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- Add support for function error injection.
- Add support for custom exception handlers, as required by
BPF_PROBE_MEM.
- Add support for BPF_PROBE_MEM.
- Add trace events for idle enter / exit for the s390 specific idle
implementation.
- Remove unused zcore memmmap device.
- Remove unused "raw view" from s390 debug feature.
- AP bus + zcrypt device driver code refactoring.
- Provide cex4 cca sysfs attributes for cex3 for zcrypt device driver.
- Expose only minimal interface to walk physmem for mm/memblock. This
is a common code change and it has been agreed on with Mike Rapoport
and Andrew Morton that this can go upstream via the s390 tree.
- Rework of the s390 vmem/vmmemap code to allow for future memory hot
remove.
- Get rid of FORCE_MAX_ZONEORDER to finally allow for order-10
allocations again, instead of only order-8 allocations.
- Various small improvements and fixes.
* tag 's390-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits)
s390/vmemmap: coding style updates
s390/vmemmap: avoid memset(PAGE_UNUSED) when adding consecutive sections
s390/vmemmap: remember unused sub-pmd ranges
s390/vmemmap: fallback to PTEs if mapping large PMD fails
s390/vmem: cleanup empty page tables
s390/vmemmap: take the vmem_mutex when populating/freeing
s390/vmemmap: cleanup when vmemmap_populate() fails
s390/vmemmap: extend modify_pagetable() to handle vmemmap
s390/vmem: consolidate vmem_add_range() and vmem_remove_range()
s390/vmem: rename vmem_add_mem() to vmem_add_range()
s390: enable HAVE_FUNCTION_ERROR_INJECTION
s390/pci: clarify comment in s390_mmio_read/write
s390/time: improve comparison for tod steering
s390/time: select CLOCKSOURCE_VALIDATE_LAST_CYCLE
s390/time: use CLOCKSOURCE_MASK
s390/bpf: implement BPF_PROBE_MEM
s390/kernel: expand exception table logic to allow new handling options
s390/kernel: unify EX_TABLE* implementations
s390/mm: allow order 10 allocations
s390/mm: avoid trimming to MAX_ORDER
...
The existing comment was talking about reading in the write part
and vice versa. While we are here make it more clear why restricting
the syscalls to MIO capable devices is okay.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In usual IPL or hot plug scenarios a zPCI function transitions directly
from reserved (invisible to Linux) to configured state or is configured
by Linux itself using an SCLP, however it can also first go from
reserved to standby and then from standby to configured without
Linux initiative.
In this scenario we first get a PEC event 0x302 and then 0x301. This may
happen for example when the device is deconfigured at another LPAR and
made available for this LPAR. It may also happen under z/VM when
a device is attached while in some inconsistent state.
However when we get the 0x301 the device is already known to zPCI
so calling zpci_create() will add it twice resulting in the below
BUG. Instead we should only enable the existing device and finally
scan it through the PCI subsystem.
list_add double add: new=00000000ed5a9008, prev=00000000ed5a9008, next=0000000083502300.
kernel BUG at lib/list_debug.c:31!
Krnl PSW : 0704c00180000000 0000000082dc2db8 (__list_add_valid+0x70/0xa8)
Call Trace:
[<0000000082dc2db8>] __list_add_valid+0x70/0xa8
([<0000000082dc2db4>] __list_add_valid+0x6c/0xa8)
[<00000000828ea920>] zpci_create_device+0x60/0x1b0
[<00000000828ef04a>] zpci_event_availability+0x282/0x2f0
[<000000008315f848>] chsc_process_crw+0x2b8/0xa18
[<000000008316735c>] crw_collect_info+0x254/0x348
[<00000000829226ea>] kthread+0x14a/0x168
[<000000008319d5c0>] ret_from_fork+0x24/0x2c
Fixes: f606b3ef47 ("s390/pci: adapt events for zbus")
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the
pdev->no_vf_scan flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio
and qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl7eVGcACgkQjYWKoQLX
FBhweQgAkicvx31x230rdfG+jQkQkl0UqF99vvWrJHEll77SqadfjzKAGIjUB+K0
EoeHVD5Wcj7BogDGcyHeQ0bZpu4WzE+y1nmnrsvu7TEEvcBmkJH0rF2jF+y0sb/O
3qvwFkX/CB5OqaMzKC/AEeRpcCKR+ZUXkWu1irbYth7CBXaycD9EAPc4cj8CfYGZ
r5njUdYOVk77TaO4aV+t5pCYc5TCRJaWXSsWaAv/nuLcIqsFBYOy2q+L47zITGXp
utZVanIDjzx+ikpaKicOIfC3hJsRuNX9MnlZKsQFwpVEZAUZmIUm29XdhGJTWSxU
RV7m1ORINbFP1nGAqWqkOvGo/LC0ZA==
=VhXR
-----END PGP SIGNATURE-----
Merge tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the pdev->no_vf_scan
flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio and
qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
* tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
vfio-ccw: make vfio_ccw_regops variables declarations static
vfio-ccw: Add trace for CRW event
vfio-ccw: Wire up the CRW irq and CRW region
vfio-ccw: Introduce a new CRW region
vfio-ccw: Refactor IRQ handlers
vfio-ccw: Introduce a new schib region
vfio-ccw: Refactor the unregister of the async regions
vfio-ccw: Register a chp_event callback for vfio-ccw
vfio-ccw: Introduce new helper functions to free/destroy regions
vfio-ccw: document possible errors
vfio-ccw: Enable transparent CCW IPL from DASD
s390/pci: Log new handle in clp_disable_fh()
s390/cio, s390/qeth: cleanup PNSO CHSC
s390/qdio: remove q->first_to_kick
s390/qdio: fix up qdio_start_irq() kerneldoc
s390: remove critical section cleanup from entry.S
s390: add machine check SIGP
s390/pci: ioremap() align with generic code
s390/ap: introduce new ap function ap_get_qdev()
Documentation/s390: Update / remove developerWorks web links
...
After disabling a function, the original handle is logged instead of
the disabled handle.
Link: https://lkml.kernel.org/r/20200522183922.5253-1-ptesarik@suse.com
Fixes: 17cdec960c ("s390/pci: Recover handle in clp_set_pci_fn()")
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Let's use the same signature and parameter names as in the generic
ioremap() definition making the physical address' type explicit.
Add a check against address wrap around as in the generic
lib/ioremap.c:ioremap_prot() code.
Finally use free_vm_area() instead of vunmap() as in the generic code.
Besides being clearer free_vm_area() can also skip a few additional
checks compared with vunmap().
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On s390 PCI Virtual Functions (VFs) are scanned by firmware and are made
available to Linux via the hot-plug interface. As such the common code
path of doing the scan directly using the parent Physical Function (PF)
is not used and fenced off with the no_vf_scan attribute.
Even if the partition created the VFs itself e.g. using the sriov_numvfs
attribute of a PF, the PF/VF links thus need to be established after the
fact. To do this when a VF is plugged we scan through all functions on
the same zbus and test whether they are the parent PF in which case we
establish the necessary links.
With these links established there is now no more need to fence off
pci_iov_remove_virtfn() for pdev->no_vf_scan as the common code now
works fine.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506154139.90609-3-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The s390_mmio_read/write syscalls are currently broken when running with
MIO.
The new pcistb_mio/pcstg_mio/pcilg_mio instructions are executed
similiarly to normal load/store instructions and do address translation
in the current address space. That means inside the kernel they are
aware of mappings into kernel address space while outside the kernel
they use user space mappings (usually created through mmap'ing a PCI
device file).
Now when existing user space applications use the s390_pci_mmio_write
and s390_pci_mmio_read syscalls, they pass I/O addresses that are mapped
into user space so as to be usable with the new instructions without
needing a syscall. Accessing these addresses with the old instructions
as done currently leads to a kernel panic.
Also, for such a user space mapping there may not exist an equivalent
kernel space mapping which means we can't just use the new instructions
in kernel space.
Instead of replicating user mappings in the kernel which then might
collide with other mappings, we can conceptually execute the new
instructions as if executed by the user space application using the
secondary address space. This even allows us to directly store to the
user pointer without the need for copy_to/from_user().
Cc: stable@vger.kernel.org
Fixes: 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The assignment of the PCI device multifunction attribute
is set during the PCI device probe.
There is no need to set it here.
Let's do it right and remove this assignment.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
We allow multiple functions on a single bus.
We suppress the ZPCI_DEVFN definition and replace its
occurences with zpci->devfn.
We verify the number of device during the registration.
There can never be more domains in use than existing
devices, so we do not need to verify the count of domain
after having verified the count of devices.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The current PCI implementation do not provide a bus resource.
This leads to a notice being print at boot.
Let's do it more nicely and provide the bus resource.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Simplify the event handling.
Set the zpci state explicitly.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The zPCI bus is in charge to handle common zPCI resources for
zPCI devices.
Creating the zPCI bus, the PCI bus, the zPCI devices and the
PCI devices and hotplug slots
done in a specific order:
- PCI hotplug slot creation needs a PCI bus
- PCI bus needs a PCI domain
which is reported by the pci_domain_nr() when setting up the
host bridge
- PCI domain is set from the zPCI with devfn 0
this is necessary to have a reproducible enumeration
Therefore we can not create devices or hotplug slots for any PCI
device associated with a zPCI device before having discovered
the function zero of the bus.
The discovery and initialization of devices can be done at several
points in the code:
- On Events, serialized in a thread context
- On initialization, in the kernel init thread context
- When powering on the hotplug slot, in a user thread context
The removal of devices and their parent bus may also be done on
events or for devices when powering down the slot.
To guarantee the existence of the bus and devices until they are
no more needed we use kref in zPCI bus and introduce a reference
count in the zPCI devices.
In this patch the zPCI bus still only accept a device with
a devfn 0.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Firmware provides the bus/devfn part of the PCI addresses of a zPCI
function inside the new field RID of the CLP query PCI function
with a bit to know if this field is available to use.
Let's add these fields to the clp_rsp_query_pci structure,
add corresponding fields to zdev and initialize them.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Using PCI multifunctions in S390 is a new feature we may want
to ignore to continue provide the same topology as in the past
to userland even if the configuration supports exposing the
topology of a multi-Function device.
A new boolean parameters allows to overwrite the kernel
pci configuration:
- pci=norid when on, disallow the use a new firmware field,
RID, which provides the PCI <bus>:<device>.<function> part
of the PCI address.
To be used in the following patches and satisfy the checkpatch.pl
the variable is exposed in pci.h
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add SysFS attribute that provides the port number for PCI functions
representing a single port of a multi-port device.
Signed-off-by: Alexander Schmidt <alexs@linux.ibm.com>
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
with the introduction of CPU directed interrupts the kernel
parameter pci=force_floating was introduced to fall back
to the previous behavior using floating irqs.
However we were still setting the affinity in that case,
both in __irq_alloc_descs() and via the irq_set_affinity
callback in struct irq_chip.
For the former only set the affinity in the directed case.
The latter is explicitly set in zpci_directed_irq_init()
so we can just leave it unset for the floating case.
Fixes: e979ce7bce ("s390/pci: provide support for CPU directed interrupts")
Co-developed-by: Alexander Schmidt <alexs@linux.ibm.com>
Signed-off-by: Alexander Schmidt <alexs@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth Vijayan
common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other fixes/improvements
in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios
mm cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl6Ig2YACgkQjYWKoQLX
FBj2gggAibnHOl9d0ngX1mVT4nz51R3V8z5sEQjNMr2uHBmaTqs7pi/00gaFMxoC
NngVEXvL443jSogQivthGgXPpRCV9xdKE3sp38j7fF4LgHoeuDtGd1oaX4W9Rqk0
7Yii35EaO2e2WHdOKaAbu+ZvDRunFjERyntc51MYaIUivFosogSo07vC73vFIArF
VGStS09fJ4Ny76ott896T7Ulx1Iek/MkF1vponEMLGNUIcLIQbbxZxOwgz0pHuEF
SlyyJBnhOIaAJGOYlKREQDt1cew+hsxluPU+a01bwdsmdZv9LH1BGwLayDqTH58i
QWvtEpzJFmDvo9jGM1v81ebaGnyCKg==
=hiGF
-----END PGP SIGNATURE-----
Merge tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth
Vijayan common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other
fixes/improvements in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios mm
cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
* tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (57 commits)
s390/mm: cleanup init_new_context() callback
s390/mm: cleanup virtual memory constants usage
s390/mm: remove page table downgrade support
s390/qdio: set qdio_irq->cdev at allocation time
s390/qdio: remove unused function declarations
s390/ccwgroup: remove pm support
s390/ap: remove power management code from ap bus and drivers
s390/zcrypt: use kvmalloc instead of kmalloc for 256k alloc
s390/mm: cleanup arch_get_unmapped_area() and friends
s390/ism: remove pm support
s390/cio: use fallthrough;
s390/vfio: use fallthrough;
s390/zcrypt: use fallthrough;
s390: use fallthrough;
s390/cpum_sf: Fix wrong page count in error message
s390/diag: fix display of diagnose call statistics
s390/ap: Remove ap device suspend and resume callbacks
s390/pci: Improve handling of unset UID
s390/pci: Fix zpci_alloc_domain() over allocation
s390/qdio: pass ISC as parameter to chsc_sadc()
...
When UID checking is enabled a UID value of 0 is invalid and can not be
set by the user. On z/VM it is however used to indicate an unset UID.
Until now, this lead to the behavior that one PCI function could be
attached with UID 0 after which z/VM would prohibit further attachment.
Now if the user then turns off UID checking in z/VM the user could
seemingly attach additional PCI functions that would however not show up
in Linux as that would not be informed of the change in UID checking
mode. This is unexpected and confusing and lead to bug reports against
Linux.
Instead now, if we encounter an unset UID value of 0 treat it as
indicating that UID checking was turned off, switch to automatic domain
allocation, and warn the user of the possible misconfiguration.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Until now zpci_alloc_domain() only prevented more than
CONFIG_PCI_NR_FUNCTIONS from being added when using automatic domain
allocation. When explicit UIDs were defined UIDs above
CONFIG_PCI_NR_FUNCTIONS were not counted at all.
When more PCI functions are added this could lead to various errors
including under sized IRQ vectors and similar issues.
Fix this by explicitly tracking the number of allocated domains.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Hibernation is known to be broken for many years on s390. Given that
there aren't any real use cases, remove the code instead of spending
time to fix and maintain it.
Without hibernate support it doesn't make too much sense to keep power
management support; therefore remove it completely.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
In the initial MIO support introduced in
commit 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
zpci_map_resource() and zpci_setup_resources() default to using the
mio_wb address as the resource's start address. This means users of the
mapping, which includes most drivers, will get write combining on PCI
Stores. This may lead to problems when drivers expect write through
behavior when not using an explicit ioremap_wc().
Cc: stable@vger.kernel.org
Fixes: 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When we try to recover a PCI function using
echo 1 > /sys/bus/pci/devices/<id>/recover
or manually with
echo 1 > /sys/bus/pci/devices/<id>/remove
echo 0 > /sys/bus/pci/slots/<slot>/power
echo 1 > /sys/bus/pci/slots/<slot>/power
clp_disable_fn() / clp_enable_fn() call clp_set_pci_fn() to first
disable and then reenable the function.
When the function is already in the requested state we may be left with
an invalid function handle.
To get a new valid handle we do a clp_list_pci() call. For this we need
both the function ID and function handle in clp_set_pci_fn() so pass the
zdev and get both.
To simplify things also pull setting the refreshed function handle into
clp_set_pci_fn()
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAl3leXUUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vyY3g/9FAVVdPEaadNtAhQ/zIxcjozDovKq
0q7yOA3aTBTUoNEinm88an6p0dcC4gNKtGukXmzVH2Hhxm9kLRdtpZGYY00tpLUB
9rI7XsgwwHa+hLwsHbIs507sKGFGy5FLr0ChTTGLDEMppnEvjA2hZooYmcB/OgrC
LlFcwbNKGOk/Si9u2bF2nLO0JDoVHnwzpF99saew/nqc7Lfj9e9IPZFom+VjPBUh
AOvRp2H7uBN+WQlpLeFeMDDoeXh34lX0kYqIV/cVkXVnknDGYKV2CBTg2aeX7jd0
QiPHZh6zlW8zNQgaCZRiBAbatVEOnRMRJ++yiqB8hBYp1LMXm6kJ01YSQpXkugoY
Vp9dtzzTARWV/XkKwD4brw9ZEmIDnO+Ed2x2VbUkPJVcXAvzSQWAx82IU0Iuqmcb
9qr6U2Zf/Xk5aFlGPYVH8QOG+QqzIbZNRQ7NlhDlITyW4P6QPu0mw374yYP2wDGL
sP5YSS3YGa0sQcEgDtVnd4z+WTZI4AwXLPaeaLkDhdfHp2FsERUY4TrPs33J99xw
og4EyokVFzjYzlnBPU6WWn7LL+jj5ccXkL3MA4DR4FJOnNGHh7NXfQUH56rrgsq7
F9/8shL5DuTbQkde1uSyUG9Iq/RigVLlV5DQavFm3dSXvZi0E16t5alC5URNTzk7
at8Bogn53QhlmYc=
=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
The config option CONFIG_PCI_NR_FUNCTIONS sets a limit on the number of
PCI functions we can support. Previously on reaching this limit there
was no indication why newly attached devices are not recognized by Linux
which could be quite confusing. Thus this patch adds a pr_err() for this
case.
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When UID checking was turned off during runtime in the underlying
hypervisor, a PCI device may be attached with the same UID. This is
already detected but happens silently. Add an error message so it can
more easily be understood why a device was not added.
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
Always inline asm inlines with variable operands for "i" constraints,
since they won't compile if the compiler would decide to not inline
them.
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- add dma-mapping and block layer helpers to take care of IOMMU
merging for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask (me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
-----BEGIN PGP SIGNATURE-----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=/wGv
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- add dma-mapping and block layer helpers to take care of IOMMU merging
for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask
(me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
* tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping: (41 commits)
mmc: renesas_sdhi_internal_dmac: Add MMC_CAP2_MERGE_CAPABLE
mmc: queue: Fix bigger segments usage
arm64: use asm-generic/dma-mapping.h
swiotlb-xen: merge xen_unmap_single into xen_swiotlb_unmap_page
swiotlb-xen: simplify cache maintainance
swiotlb-xen: use the same foreign page check everywhere
swiotlb-xen: remove xen_swiotlb_dma_mmap and xen_swiotlb_dma_get_sgtable
xen: remove the exports for xen_{create,destroy}_contiguous_region
xen/arm: remove xen_dma_ops
xen/arm: simplify dma_cache_maint
xen/arm: use dev_is_dma_coherent
xen/arm: consolidate page-coherent.h
xen/arm: use dma-noncoherent.h calls for xen-swiotlb cache maintainance
arm: remove wrappers for the generic dma remap helpers
dma-mapping: introduce a dma_common_find_pages helper
dma-mapping: always use VM_DMA_COHERENT for generic DMA remap
vmalloc: lift the arm flag for coherent mappings to common code
dma-mapping: provide a better default ->get_required_mask
dma-mapping: remove the dma_declare_coherent_memory export
remoteproc: don't allow modular build
...
After recent changes the MSI message data needs to specify the
function-relative IRQ number.
Reported-and-tested-by: Alexander Schmidt <alexs@linux.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
While the default ->mmap and ->get_sgtable implementations work for the
majority of our dma_map_ops impementations they are inherently safe
for others that don't use the page allocator or CMA and/or use their
own way of remapping not covered by the common code. So remove the
defaults if these methods are not wired up, but instead wire up the
default implementations for all safe instances.
Fixes: e1c7e32453 ("dma-mapping: always provide the dma_map_ops based implementation")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Command line option values passed to __setup callbacks are always
null-terminated and "s390_iommu=" may only accept "strict" as value.
So replace strncmp with strcmp.
While at it also make s390_iommu_setup return 1, which means this
command line option is handled by this callback.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This patch alters the for loop iteration scheme in zpci_map_resources
to make it more usual. Thus, the patch generalizes the style for
PCI_IOV_RESOURCES iteration and improves readability.
Link: http://lkml.kernel.org/r/20190806160137.29275-1-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Fix integer overflow during stack frame unwind with invalid backchain.
- Cleanup unused symbol export in zcrypt code.
- Fix MIO addressing control activation in PCI code and expose its
usage via sysfs.
- Fix kernel image signature verification report presence detection.
- Fix irq registration in vfio-ap code.
- Add CPU measurement counters for newer machines.
- Add base DASD thin provisioning support and code cleanups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl0oirgACgkQjYWKoQLX
FBiL7gf+MOToP48a3h+lLcIrbH48B2+OR3W+kIID5qR0GtDoPU2gd2HtSwrn9frs
jgh5ZLwGgrnSU/MqFXpCwDfD7x0mSWL/HunlSck1zf6h22LmuYjcjntWzHTS7csv
gTFKNSQX4AdgZAdTEeqC+Axem2ygtpELhe35NPT8HBQD52twe1XkniDl8gu7/zj2
WdPAGsm30wlodIUFt+di4IQAxSQGkDl9nKN+IIREPjdq/kFKP3pFKzXf5k0FduVk
v+VOb+KENzeJoqPqRD/GS+vdVm52gqRbKrJVm+p5NlltGDPoa0m3u4Cjy2ZVA2/t
+BKv4aGHseb6x89XTPIaf1dTLDNf6w==
=GxOr
-----END PGP SIGNATURE-----
Merge tag 's390-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Fix integer overflow during stack frame unwind with invalid
backchain.
- Cleanup unused symbol export in zcrypt code.
- Fix MIO addressing control activation in PCI code and expose its
usage via sysfs.
- Fix kernel image signature verification report presence detection.
- Fix irq registration in vfio-ap code.
- Add CPU measurement counters for newer machines.
- Add base DASD thin provisioning support and code cleanups.
* tag 's390-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (21 commits)
s390/unwind: avoid int overflow in outside_of_stack
s390/zcrypt: remove the exporting of ap_query_configuration
s390/pci: add mio_enabled attribute
s390: fix setting of mio addressing control
s390/ipl: Fix detection of has_secure attribute
s390: vfio-ap: fix irq registration
s390/cpumf: Add extended counter set definitions for model 8561 and 8562
s390/dasd: Handle out-of-space constraint
s390/dasd: Add discard support for ESE volumes
s390/dasd: Use ALIGN_DOWN macro
s390/dasd: Make dasd_setup_queue() a discipline function
s390/dasd: Add new ioctl to release space
s390/dasd: Add dasd_sleep_on_queue_interruptible()
s390/dasd: Add missing intensity definition
s390/dasd: Fix whitespace
s390/dasd: Add dynamic formatting support for ESE volumes
s390/dasd: Recognise data for ESE volumes
s390/dasd: Put sub-order definitions in a separate section
s390/dasd: Make layout analysis ESE compatible
s390/dasd: Remove old defines and function
...
Provide an attribute to query the usage of mio instructions.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Move enablement of mio addressing control from detect_machine_facilities
to pci_base_init. detect_machine_facilities runs so early that the
static branches have not been toggled yet, thus mio addressing control
was always off. In pci_base_init we have to use the SMP aware
ctl_set_bit though.
Fixes: 833b441ec0 ("s390: enable processes for mio instructions")
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- rwsem scalability improvements, phase #2, by Waiman Long, which are
rather impressive:
"On a 2-socket 40-core 80-thread Skylake system with 40 reader
and writer locking threads, the min/mean/max locking operations
done in a 5-second testing window before the patchset were:
40 readers, Iterations Min/Mean/Max = 1,807/1,808/1,810
40 writers, Iterations Min/Mean/Max = 1,807/50,344/151,255
After the patchset, they became:
40 readers, Iterations Min/Mean/Max = 30,057/31,359/32,741
40 writers, Iterations Min/Mean/Max = 94,466/95,845/97,098"
There's a lot of changes to the locking implementation that makes
it similar to qrwlock, including owner handoff for more fair
locking.
Another microbenchmark shows how across the spectrum the
improvements are:
"With a locking microbenchmark running on 5.1 based kernel, the
total locking rates (in kops/s) on a 2-socket Skylake system
with equal numbers of readers and writers (mixed) before and
after this patchset were:
# of Threads Before Patch After Patch
------------ ------------ -----------
2 2,618 4,193
4 1,202 3,726
8 802 3,622
16 729 3,359
32 319 2,826
64 102 2,744"
The changes are extensive and the patch-set has been through
several iterations addressing various locking workloads. There
might be more regressions, but unless they are pathological I
believe we want to use this new implementation as the baseline
going forward.
- jump-label optimizations by Daniel Bristot de Oliveira: the primary
motivation was to remove IPI disturbance of isolated RT-workload
CPUs, which resulted in the implementation of batched jump-label
updates. Beyond the improvement of the real-time characteristics
kernel, in one test this patchset improved static key update
overhead from 57 msecs to just 1.4 msecs - which is a nice speedup
as well.
- atomic64_t cross-arch type cleanups by Mark Rutland: over the last
~10 years of atomic64_t existence the various types used by the
APIs only had to be self-consistent within each architecture -
which means they became wildly inconsistent across architectures.
Mark puts and end to this by reworking all the atomic64
implementations to use 's64' as the base type for atomic64_t, and
to ensure that this type is consistently used for parameters and
return values in the API, avoiding further problems in this area.
- A large set of small improvements to lockdep by Yuyang Du: type
cleanups, output cleanups, function return type and othr cleanups
all around the place.
- A set of percpu ops cleanups and fixes by Peter Zijlstra.
- Misc other changes - please see the Git log for more details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (82 commits)
locking/lockdep: increase size of counters for lockdep statistics
locking/atomics: Use sed(1) instead of non-standard head(1) option
locking/lockdep: Move mark_lock() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
x86/jump_label: Make tp_vec_nr static
x86/percpu: Optimize raw_cpu_xchg()
x86/percpu, sched/fair: Avoid local_clock()
x86/percpu, x86/irq: Relax {set,get}_irq_regs()
x86/percpu: Relax smp_processor_id()
x86/percpu: Differentiate this_cpu_{}() and __this_cpu_{}()
locking/rwsem: Guard against making count negative
locking/rwsem: Adaptive disabling of reader optimistic spinning
locking/rwsem: Enable time-based spinning on reader-owned rwsem
locking/rwsem: Make rwsem->owner an atomic_long_t
locking/rwsem: Enable readers spinning on writer
locking/rwsem: Clarify usage of owner's nonspinaable bit
locking/rwsem: Wake up almost all readers in wait queue
locking/rwsem: More optimal RT task handling of null owner
locking/rwsem: Always release wait_lock before waking up tasks
locking/rwsem: Implement lock handoff to prevent lock starvation
locking/rwsem: Make rwsem_spin_on_owner() return owner state
...
Do not issue CLP_SET_ENABLE_MIO after opting out of MIO instruction
usage. This should not fix a bug but reduce overhead within firmware.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Unfortunately we have to handle a class of devices that don't support the
new MIO instructions. Adjust resource assignment and mapping accordingly.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Adjust bus resources depending on the usage of MIO instructions.
Fixes: 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Niklas Schnelle