A user noticed that write performance was horrible over loopback and we
traced it to an inversion of when we need to set MSG_MORE. It should be
set when we have more bvec's to send, not when we are on the last bvec.
This patch made the test go from 20 iops to 78k iops.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Fixes: 429a787be6 ("nbd: fix use-after-free of rq/bio in the xmit path")
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block fixes from Jens Axboe:
- the virtio_blk stack DMA corruption fix from Christoph, fixing and
issue with VMAP stacks.
- O_DIRECT blkbits calculation fix from Chandan.
- discard regression fix from Christoph.
- queue init error handling fixes for nbd and virtio_blk, from Omar and
Jeff.
- two small nvme fixes, from Christoph and Guilherme.
- rename of blk_queue_zone_size and bdev_zone_size to _sectors instead,
to more closely follow what we do in other places in the block layer.
This interface is new for this series, so let's get the naming right
before releasing a kernel with this feature. From Damien.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: don't try to discard from __blkdev_issue_zeroout
sd: remove __data_len hack for WRITE SAME
nvme: use blk_rq_payload_bytes
scsi: use blk_rq_payload_bytes
block: add blk_rq_payload_bytes
block: Rename blk_queue_zone_size and bdev_zone_size
nvme: apply DELAY_BEFORE_CHK_RDY quirk at probe time too
nvme-rdma: fix nvme_rdma_queue_is_ready
virtio_blk: fix panic in initialization error path
nbd: blk_mq_init_queue returns an error code on failure, not NULL
virtio_blk: avoid DMA to stack for the sense buffer
do_direct_IO: Use inode->i_blkbits to compute block count to be cleaned
zram has used per-cpu stream feature from v4.7. It aims for increasing
cache hit ratio of scratch buffer for compressing. Downside of that
approach is that zram should ask memory space for compressed page in
per-cpu context which requires stricted gfp flag which could be failed.
If so, it retries to allocate memory space out of per-cpu context so it
could get memory this time and compress the data again, copies it to the
memory space.
In this scenario, zram assumes the data should never be changed but it is
not true without stable page support. So, If the data is changed under
us, zram can make buffer overrun so that zsmalloc free object chain is
broken so system goes crash like below
https://bugzilla.suse.com/show_bug.cgi?id=997574
This patch adds BDI_CAP_STABLE_WRITES to zram for declaring "I am block
device needing *stable write*".
Fixes: da9556a236 ("zram: user per-cpu compression streams")
Link: http://lkml.kernel.org/r/1482366980-3782-4-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Hyeoncheol Lee <cheol.lee@lge.com>
Cc: <yjay.kim@lge.com>
Cc: Sangseok Lee <sangseok.lee@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: <stable@vger.kernel.org> [4.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b4c5c60920 ("zram: avoid lockdep splat by revalidate_disk")
moved revalidate_disk call out of init_lock to avoid lockdep
false-positive splat. However, commit 08eee69fcf ("zram: remove
init_lock in zram_make_request") removed init_lock in IO path so there
is no worry about lockdep splat. So, let's restore it.
This patch is needed to set BDI_CAP_STABLE_WRITES atomically in next
patch.
Fixes: da9556a236 ("zram: user per-cpu compression streams")
Link: http://lkml.kernel.org/r/1482366980-3782-3-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Hyeoncheol Lee <cheol.lee@lge.com>
Cc: <yjay.kim@lge.com>
Cc: Sangseok Lee <sangseok.lee@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: <stable@vger.kernel.org> [4.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If blk_mq_init_queue() returns an error, it gets assigned to
vblk->disk->queue. Then, when we call put_disk(), we end up calling
blk_put_queue() with the ERR_PTR, causing a bad dereference. Fix it by
only assigning to vblk->disk->queue on success.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Additionally, don't assign directly to disk->queue, otherwise
blk_put_queue (called via put_disk) will choke (panic) on the errno
stored there.
Bug found by code inspection after Omar found a similar issue in
virtio_blk. Compile-tested only.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Most users of BLOCK_PC requests allocate the sense buffer on the stack,
so to avoid DMA to the stack copy them to a field in the heap allocated
virtblk_req structure. Without that any attempt at SCSI passthrough I/O,
including the SG_IO ioctl from userspace will crash the kernel. Note that
this includes running tools like hdparm even when the host does not have
SCSI passthrough enabled.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Jens Axboe <axboe@fb.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- a large rework of cephx auth code to cope with CONFIG_VMAP_STACK
(myself). Also fixed a deadlock caused by a bogus allocation on the
writeback path and authorize reply verification.
- a fix for long stalls during fsync (Jeff Layton). The client now
has a way to force the MDS log flush, leading to ~100x speedups in
some synthetic tests.
- a new [no]require_active_mds mount option (Zheng Yan). On mount, we
will now check whether any of the MDSes are available and bail rather
than block if none are. This check can be avoided by specifying the
"no" option.
- a couple of MDS cap handling fixes and a few assorted patches
throughout.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJYVByGAAoJEEp/3jgCEfOLBqkH/A7nVf7ObSDYmLuYgg1gJ8zq
4zDDE42S4yZwayAVpn3UjbfPuez5J44lsdXitExdfiHOdIQZDa/WqAbSqQ48HCSg
7sG6ecRWg3G5zG0psPZnB+S5wGMvsLXmj2hvzV1lt2t0lI5bDLSlNRSnElbhilD/
8Z7+Ni2go8DMC9o49SJU32lBW7IByKl4p4flveItgwUvGkIFNd8OT3CyPBUqonQs
lRCeImRYU8Jghb+ifnRxWSbuDf7pZAPc9kL0vibpUUT/1bH6iHsedKp37WQKqc/w
KDSNnKiZcz0gY/hJeLqE3ymCIKO6SU+JkMQSaYNTouLO5fQsRr8/uWQXSe6S5oc=
=ypWx
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.10-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A varied set of changes:
- a large rework of cephx auth code to cope with CONFIG_VMAP_STACK
(myself). Also fixed a deadlock caused by a bogus allocation on the
writeback path and authorize reply verification.
- a fix for long stalls during fsync (Jeff Layton). The client now
has a way to force the MDS log flush, leading to ~100x speedups in
some synthetic tests.
- a new [no]require_active_mds mount option (Zheng Yan).
On mount, we will now check whether any of the MDSes are available
and bail rather than block if none are. This check can be avoided
by specifying the "no" option.
- a couple of MDS cap handling fixes and a few assorted patches
throughout"
* tag 'ceph-for-4.10-rc1' of git://github.com/ceph/ceph-client: (32 commits)
libceph: remove now unused finish_request() wrapper
libceph: always signal completion when done
ceph: avoid creating orphan object when checking pool permission
ceph: properly set issue_seq for cap release
ceph: add flags parameter to send_cap_msg
ceph: update cap message struct version to 10
ceph: define new argument structure for send_cap_msg
ceph: move xattr initialzation before the encoding past the ceph_mds_caps
ceph: fix minor typo in unsafe_request_wait
ceph: record truncate size/seq for snap data writeback
ceph: check availability of mds cluster on mount
ceph: fix splice read for no Fc capability case
ceph: try getting buffer capability for readahead/fadvise
ceph: fix scheduler warning due to nested blocking
ceph: fix printing wrong return variable in ceph_direct_read_write()
crush: include mapper.h in mapper.c
rbd: silence bogus -Wmaybe-uninitialized warning
libceph: no need to drop con->mutex for ->get_authorizer()
libceph: drop len argument of *verify_authorizer_reply()
libceph: verify authorize reply on connect
...
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYT5HMAAoJELDendYovxMvhNQH/1g/3ahM4JKN8Z0SbjKBEdQm
yj2xOj6cE3l6wMSUblKjZD2DLLhpmcHT/E97Xro/lZQEfQJoMXXWWDFowMU/P1LA
mJxb7Fzq5Wr+6eGSAlIQB270MrpNi/luf+CWHMwVA3V7R3KRXwonOdGQSkISIzCd
tgIydEA3a9r2+HgeIBpZFZ4GcSrJQU75krMyl2tjD1C+jeYVd+zdoj2OnDsZQDZQ
hDWApMpNbpSBAn7JtSSdXWSTBsGH0lUECebeYPhPQ2sX2P6Y8+UCGwA7i6FFdbTa
agXfVSdRz8dCe3k19VcKDAw6nK9BTTMnEeEHmkmygIh6wuHPP44CzigTXIbJoXI=
=zjfm
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes for 4.10
These are some fixes, a move of some arm related headers to share them
between arm and arm64 and a series introducing a helper to make code
more readable.
The most notable change is David stepping down as maintainer of the
Xen hypervisor interface. This results in me sending you the pull
requests for Xen related code from now on"
* tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits)
xen/balloon: Only mark a page as managed when it is released
xenbus: fix deadlock on writes to /proc/xen/xenbus
xen/scsifront: don't request a slot on the ring until request is ready
xen/x86: Increase xen_e820_map to E820_X_MAX possible entries
x86: Make E820_X_MAX unconditionally larger than E820MAX
xen/pci: Bubble up error and fix description.
xen: xenbus: set error code on failure
xen: set error code on failures
arm/xen: Use alloc_percpu rather than __alloc_percpu
arm/arm64: xen: Move shared architecture headers to include/xen/arm
xen/events: use xen_vcpu_id mapping for EVTCHNOP_status
xen/gntdev: Use VM_MIXEDMAP instead of VM_IO to avoid NUMA balancing
xen-scsifront: Add a missing call to kfree
MAINTAINERS: update XEN HYPERVISOR INTERFACE
xenfs: Use proc_create_mount_point() to create /proc/xen
xen-platform: use builtin_pci_driver
xen-netback: fix error handling output
xen: make use of xenbus_read_unsigned() in xenbus
xen: make use of xenbus_read_unsigned() in xen-pciback
xen: make use of xenbus_read_unsigned() in xen-fbfront
...
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
drivers/block/rbd.c: In function ‘rbd_watch_cb’:
drivers/block/rbd.c:3690:5: error: ‘struct_v’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/block/rbd.c:3759:5: note: ‘struct_v’ was declared here
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
While doing stress tests we noticed that we'd get a lot of dmesg spam if
we suddenly disconnected the nbd device out of band. Rate limit the
messages in the io path in order to deal with this.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If an app exits before running NBD_DO_IT but after adding sockets we can
end up not being allowed to do a new nbd device. Fix this by making
NBD_CLEAR_SOCK reset the setup_task.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
zram hot_add sysfs attribute is a very 'special' attribute - reading
from it creates a new uninitialized zram device. This file, by a
mistake, can be read by a 'normal' user at the moment, while only root
must be able to create a new zram device, therefore hot_add attribute
must have S_IRUSR mode, not S_IRUGO.
[akpm@linux-foundation.org: s/sence/sense/, reflow comment to use 80 cols]
Fixes: 6566d1a32b ("zram: add dynamic device add/remove functionality")
Link: http://lkml.kernel.org/r/20161205155845.20129-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Steven Allen <steven@stebalien.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org> [4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have this:
ERROR: "__aeabi_ldivmod" [drivers/block/nbd.ko] undefined!
ERROR: "__divdi3" [drivers/block/nbd.ko] undefined!
nbd.c:(.text+0x247c72): undefined reference to `__divdi3'
due to a recent commit, that did 64-bit division. Use the proper
divider function so that 32-bit compiles don't break.
Fixes: ef77b51524 ("nbd: use loff_t for blocksize and nbd_set_size args")
Signed-off-by: Jens Axboe <axboe@fb.com>
If we have large devices (say like the 40t drive I was trying to test with) we
will end up overflowing the int arguments to nbd_set_size and not get the right
size for our device. Fix this by using loff_t everywhere so I don't have to
think about this again. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Install the callbacks via the state machine with multi instance support and let
the core invoke the callbacks on the already online CPUs.
[bigeasy: wire up the multi instance stuff]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: rt@linutronix.de
Cc: Nitin Gupta <ngupta@vflare.org>
Link: http://lkml.kernel.org/r/20161126231350.10321-19-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix bug https://bugzilla.kernel.org/show_bug.cgi?id=188531. In function
mtip_block_initialize(), variable rv takes the return value, and its
value should be negative on errors. rv is initialized as 0 and is not
reset when the call to ida_pre_get() fails. So 0 may be returned.
The return value 0 indicates that there is no error, which may be
inconsistent with the execution status. This patch fixes the bug by
explicitly assigning -ENOMEM to rv on the branch that ida_pre_get()
fails.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The zram hot removal code calls idr_remove() even when zram_remove()
returns an error (typically -EBUSY). This results in a leftover at the
device release, eventually leading to a crash when the module is
reloaded.
As described in the bug report below, the following procedure would
cause an Oops with zram:
- provision three zram devices via modprobe zram num_devices=3
- configure a size for each device
+ echo "1G" > /sys/block/$zram_name/disksize
- mkfs and mount zram0 only
- attempt to hot remove all three devices
+ echo 2 > /sys/class/zram-control/hot_remove
+ echo 1 > /sys/class/zram-control/hot_remove
+ echo 0 > /sys/class/zram-control/hot_remove
- zram0 removal fails with EBUSY, as expected
- unmount zram0
- try zram0 hot remove again
+ echo 0 > /sys/class/zram-control/hot_remove
- fails with ENODEV (unexpected)
- unload zram kernel module
+ completes successfully
- zram0 device node still exists
- attempt to mount /dev/zram0
+ mount command is killed
+ following BUG is encountered
BUG: unable to handle kernel paging request at ffffffffa0002ba0
IP: get_disk+0x16/0x50
Oops: 0000 [#1] SMP
CPU: 0 PID: 252 Comm: mount Not tainted 4.9.0-rc6 #176
Call Trace:
exact_lock+0xc/0x20
kobj_lookup+0xdc/0x160
get_gendisk+0x2f/0x110
__blkdev_get+0x10c/0x3c0
blkdev_get+0x19d/0x2e0
blkdev_open+0x56/0x70
do_dentry_open.isra.19+0x1ff/0x310
vfs_open+0x43/0x60
path_openat+0x2c9/0xf30
do_filp_open+0x79/0xd0
do_sys_open+0x114/0x1e0
SyS_open+0x19/0x20
entry_SYSCALL_64_fastpath+0x13/0x94
This patch adds the proper error check in hot_remove_store() not to call
idr_remove() unconditionally.
Fixes: 17ec4cd985 ("zram: don't call idr_remove() from zram_remove()")
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=1010970
Link: http://lkml.kernel.org/r/20161121132140.12683-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: David Disseldorp <ddiss@suse.de>
Reported-by: David Disseldorp <ddiss@suse.de>
Tested-by: David Disseldorp <ddiss@suse.de>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: <stable@vger.kernel.org> [4.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Multiple paths don't set it properly, ensure that we do.
Fixes: 9561a7ade0 ("nbd: add multi-connection support")
Signed-off-by: Jens Axboe <axboe@fb.com>
NBD can become contended on its single connection. We have to serialize all
writes and we can only process one read response at a time. Fix this by
allowing userspace to provide multiple connections to a single nbd device. This
coupled with block-mq drastically increases performance in multi-process cases.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For a non-cloned bio, bio_add_page() only returns failure when
the io vec table is full, but in that case, bio->bi_vcnt can't
be zero at all.
So remove the impossible failure handling.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Some drivers often use external bvec table, so introduce
this helper for this case. It is always safe to access the
bio->bi_io_vec in this way for this case.
After converting to this usage, it will becomes a bit easier
to evaluate the remaining direct access to bio->bi_io_vec,
so it can help to prepare for the following multipage bvec
support.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixed up the new O_DIRECT cases.
Signed-off-by: Jens Axboe <axboe@fb.com>
This driver is both orphaned, and not really useful anymore. Mark
it as such, and remove it in a future kernel after a release or
two.
Signed-off-by: Jens Axboe <axboe@fb.com>
For writes, we can get a completion in while we're still iterating
the request and bio chain. If that happens, we're reading freed
memory and we can crash.
Break out after the last segment and avoid having the iterator
read freed memory.
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If CONFIG_NVM is disabled, loading null_block module with use_lightnvm=1
fails. But there are no messages and documents related to the failure.
Add the appropriate error message.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Massaged the text a bit.
Signed-off-by: Jens Axboe <axboe@fb.com>
->queue_rq() should return one of the BLK_MQ_RQ_QUEUE_* constants, not
an errno.
f4aa4c7bba ("block: loop: convert to per-device workqueue")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
aoeblk contains some mysterious code, that wants to elevate the bio
vec page counts while it's under IO. That is not needed, it's
fragile, and it's causing kernel oopses for some.
Reported-by: Tested-by: Don Koch <kochd@us.ibm.com>
Tested-by: Tested-by: Don Koch <kochd@us.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is no need to call kfree() if memdup_user() fails, as no memory
was allocated and the error in the error-valued pointer should be returned.
Signed-off-by: Sachin Shukla <sachin.s5@samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Building with W=1 shows a harmless warning for the skd driver:
drivers/block/skd_main.c:2959:1: error: ‘static’ is not at beginning of declaration [-Werror=old-style-declaration]
This changes the prototype to the expected formatting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
As reported by gcc -Wmaybe-uninitialized, the cleanup path for
skd_acquire_msix tries to free the already allocated msi-x vectors
in reverse order, but the index variable may not have been
used yet:
drivers/block/skd_main.c: In function ‘skd_acquire_irq’:
drivers/block/skd_main.c:3890:8: error: ‘i’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the failure path to skip releasing the interrupts
if we have not started requesting them yet.
Fixes: 180b0ae77d ("skd: use pci_alloc_irq_vectors")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't pass a size larger than iov_len to kernel_sendmsg().
Otherwise it will cause a NULL pointer deref when kernel_sendmsg()
returns with rv < size.
DRBD as external module has been around in the kernel 2.4 days already.
We used to be compatible to 2.4 and very early 2.6 kernels,
we used to use
rv = sock_sendmsg(sock, &msg, iov.iov_len);
then later changed to
rv = kernel_sendmsg(sock, &msg, &iov, 1, size);
when we should have used
rv = kernel_sendmsg(sock, &msg, &iov, 1, iov.iov_len);
tcp_sendmsg() used to totally ignore the size parameter.
57be5bd ip: convert tcp_sendmsg() to iov_iter primitives
changes that, and exposes our long standing error.
Even with this error exposed, to trigger the bug, we would need to have
an environment (config or otherwise) causing us to not use sendpage()
for larger transfers, a failing connection, and have it fail "just at the
right time". Apparently that was unlikely enough for most, so this went
unnoticed for years.
Still, it is known to trigger at least some of these,
and suspected for the others:
[0] http://lists.linbit.com/pipermail/drbd-user/2016-July/023112.html
[1] http://lists.linbit.com/pipermail/drbd-dev/2016-March/003362.html
[2] https://forums.grsecurity.net/viewtopic.php?f=3&t=4546
[3] https://ubuntuforums.org/showthread.php?t=2336150
[4] http://e2.howsolveproblem.com/i/1175162/
This should go into 4.9,
and into all stable branches since and including v4.0,
which is the first to contain the exposing change.
It is correct for all stable branches older than that as well
(which contain the DRBD driver; which is 2.6.33 and up).
It requires a small "conflict" resolution for v4.4 and earlier, with v4.5
we dropped the comment block immediately preceding the kernel_sendmsg().
Fixes: b411b3637f ("The DRBD driver")
Cc: <stable@vger.kernel.org> # 2.6.33.x-
Cc: viro@zeniv.linux.org.uk
Cc: christoph.lechleitner@iteg.at
Cc: wolfgang.glas@iteg.at
Reported-by: Christoph Lechleitner <christoph.lechleitner@iteg.at>
Tested-by: Christoph Lechleitner <christoph.lechleitner@iteg.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
[changed oneliner to be "obvious" without context; more verbose message]
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For small buffers we may use %*ph[N] specifier, for the bigger blocks
print_hex_dump() call.
Cc: Don Brace <don.brace@microsemi.com>
Cc: esc.storagedev@microsemi.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace custom approach by %*ph specifier to dump small buffers in hex format.
Unfortunately we can't use print_hex_dump_bytes() here since tha gap is
present, though one familiar with the code may change this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Switch the skd driver to use pci_alloc_irq_vectors. We need to two calls to
pci_alloc_irq_vectors as skd only supports multiple MSI-X vectors, but not
multiple MSI vectors.
Otherwise this cleans up a lot of cruft and allows to a lot more common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Hi Peter, hi Jens,
I've been looking over the multi page bio vec work again recently, and
one of the stumbling blocks is raw biovec access in the pktcdvd.
The first issue is that it directly sets up the page and offset pointers
in the biovec just before calling bio_add_page. As bio_add_page already
does the setup it's trivial to just switch it to stack variables for the
arguments.
The second issue is the copy code in pkt_make_local_copy, which
effectively is an opencoded version of bio_copy_data except that it
skips pages that already are the same in the ѕource and destination.
But we look at the only calleer we just set up the bio using bio_add_page
to point exactly to the page array that pkt_make_local_copy compares,
so the pages will always be the same and we can just remove this function.
Note that all this is done based on code inspection, I don't have any
packet writing hardware myself.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of some reads from int to unsigned,
but these cases have been wrong before: negative values are not allowed
for the modified cases.
Cc: konrad.wilk@oracle.com
Cc: roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of one read from int to unsigned,
but this case has been wrong before: negative values are not allowed
for the modified case.
Cc: konrad.wilk@oracle.com
Cc: roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
'blk_mq_alloc_request()' returns an error pointer in case of error, not
NULL. So test it with IS_ERR.
Fixes: fd8383fd88 ("nbd: convert to blkmq")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jens Axboe <axboe@fb.com>
Most blk_mq_requeue_request() and blk_mq_add_to_requeue_list() calls
are followed by kicking the requeue list. Hence add an argument to
these two functions that allows to kick the requeue list. This was
proposed by Christoph Hellwig.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since blk_mq_requeue_work() starts stopped queues and since
execution of this function can be scheduled after a queue has
been stopped it is not possible to stop queues without using
an additional state variable to track whether or not the queue
has been stopped. Hence modify blk_mq_requeue_work() such that it
does not start stopped queues. My conclusion after a review of
the blk_mq_stop_hw_queues() and blk_mq_{delay_,}kick_requeue_list()
callers is as follows:
* In the dm driver starting and stopping queues should only happen
if __dm_suspend() or __dm_resume() is called and not if the
requeue list is processed.
* In the SCSI core queue stopping and starting should only be
performed by the scsi_internal_device_block() and
scsi_internal_device_unblock() functions but not by any other
function. Although the blk_mq_stop_hw_queue() call in
scsi_queue_rq() may help to reduce CPU load if a LLD queue is
full, figuring out whether or not a queue should be restarted
when requeueing a command would require to introduce additional
locking in scsi_mq_requeue_cmd() to avoid a race with
scsi_internal_device_block(). Avoid this complexity by removing
the blk_mq_stop_hw_queue() call from scsi_queue_rq().
* In the NVMe core only the functions that call
blk_mq_start_stopped_hw_queues() explicitly should start stopped
queues.
* A blk_mq_start_stopped_hwqueues() call must be added in the
xen-blkfront driver in its blkif_recover() function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove the WRITE_* and READ_SYNC wrappers, and just use the flags
directly. Where applicable this also drops usage of the
bio_set_op_attrs wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Noidle should be the default for writes as seen by all the compounds
definitions in fs.h using it. In fact only direct I/O really should
be using NODILE, so turn the whole flag around to get the defaults
right, which will make our life much easier especially onces the
WRITE_* defines go away.
This assumes all the existing "raw" users of REQ_SYNC for writes
want noidle behavior, which seems to be spot on from a quick audit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Josef Bacik