When running a 32bit guest under a 64bit hypervisor, the ARMv8
architecture defines a mapping of the 32bit registers in the 64bit
space. This includes banked registers that are being demultiplexed
over the 64bit ones.
On exceptions caused by an operation involving a 32bit register, the
HW exposes the register number in the ESR_EL2 register. It was so
far understood that SW had to distinguish between AArch32 and AArch64
accesses (based on the current AArch32 mode and register number).
It turns out that I misinterpreted the ARM ARM, and the clue is in
D1.20.1: "For some exceptions, the exception syndrome given in the
ESR_ELx identifies one or more register numbers from the issued
instruction that generated the exception. Where the exception is
taken from an Exception level using AArch32 these register numbers
give the AArch64 view of the register."
Which means that the HW is already giving us the translated version,
and that we shouldn't try to interpret it at all (for example, doing
an MMIO operation from the IRQ mode using the LR register leads to
very unexpected behaviours).
The fix is thus not to perform a call to vcpu_reg32() at all from
vcpu_reg(), and use whatever register number is supplied directly.
The only case we need to find out about the mapping is when we
actively generate a register access, which only occurs when injecting
a fault in a guest.
Cc: stable@vger.kernel.org
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The open coded tests for checking whether a PTE maps a page as
uncached use a flawed '(pte_val(xxx) & CONST) != CONST' pattern,
which is not guaranteed to work since the type of a mapping is
not a set of mutually exclusive bits
For HYP mappings, the type is an index into the MAIR table (i.e, the
index itself does not contain any information whatsoever about the
type of the mapping), and for stage-2 mappings it is a bit field where
normal memory and device types are defined as follows:
#define MT_S2_NORMAL 0xf
#define MT_S2_DEVICE_nGnRE 0x1
I.e., masking *and* comparing with the latter matches on the former,
and we have been getting lucky merely because the S2 device mappings
also have the PTE_UXN bit set, or we would misidentify memory mappings
as device mappings.
Since the unmap_range() code path (which contains one instance of the
flawed test) is used both for HYP mappings and stage-2 mappings, and
considering the difference between the two, it is non-trivial to fix
this by rewriting the tests in place, as it would involve passing
down the type of mapping through all the functions.
However, since HYP mappings and stage-2 mappings both deal with host
physical addresses, we can simply check whether the mapping is backed
by memory that is managed by the host kernel, and only perform the
D-cache maintenance if this is the case.
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
To avoid even more code duplication punt this all to the probe worker,
which needs some slight adjustment to also generate a uevent when the
status has changed to due connector->force.
v2: Instead of running the output_poll_work (which is kinda the wrong
thing and a layering violation since it's an internal of the probe
helpers), or calling ->detect (which is again a layering violation
since it's used only by probe helpers) just call the official
->fill_modes function, like a GET_CONNECTOR ioctl call.
v3: Restore the accidentally removed forced-probe for echo "detect" >
force.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447951610-12622-22-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the correct function name for drm_atomic_clean_old_fb docs.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When backwards is 0, __drm_mm_for_each_hole is same as
drm_mm_for_each_hole. So I rewrite drm_mm_for_each_hole
by using __drm_mm_for_each_hole.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We chase pointers/lists without taking the locks protecting them,
which isn't that good.
Fix it.
v2: Actually unlock properly, spotted by Julia.
v3: Put the label _before_ the mutex_unlock (Emil)
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Link: http://patchwork.freedesktop.org/patch/msgid/1443783662-23066-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To aid in debugging failures, print the src,dst,clip rectangles
when drm_plane_helper_check_update() fails.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow the caller to specify a "prefix" string to drm_rect_debug_print()
to make it easier to see which drm_rect is being printed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drivers shouldn't clobber the passed in addfb ioctl parameters.
i915 was doing just that. To prevent it from happening again,
pass the struct around as const, starting all the way from
internal_framebuffer_create().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The simple_strtoul function is marked as obsolete.
This patch replace it by kstrtouint.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adds clarification of the rotation property bits. I.e. rotation is
counter clockwise and that reflects are applied before any rotation.
v2: Refer to the define names instead of the property values.
Signed-off-by: Robert Fekete <robert.fekete@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I noticed that intel_fbdev->our_mode is unused. Introduced by
79e539453b ("DRM: i915: add mode setting support").
Then I noticed that intel_fbdev->fbdev_list is unused as well.
Introduced by 386516744b ("drm/fb: fix fbdev object model +
cleanup properly.") in i915, nouveau and radeon.
Subsequently cargo culted to amdgpu, ast, cirrus, qxl, udl,
virtio and mgag200.
Already removed from the latter with cc59487a05 ("drm/mgag200:
'fbdev_list' in 'struct mga_fbdev' is not used").
Remove it from the others.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The drm_property_unreference_blob() function tests whether its argument
is NULL and then returns immediately.
Thus the tests around the calls are not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: http://patchwork.freedesktop.org/patch/msgid/563C8B3E.405@users.sourceforge.net
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_TEGRA_FBDEV config is currently used to enable/disable legacy fbdev
emulation for the tegra kms driver.
Remove this local config option and use the top level DRM_FBDEV_EMULATION
config option instead.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1445933459-5249-4-git-send-email-architt@codeaurora.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_IMX_FB_HELPER config is currently used to enable/disable fbdev
emulation for the imx kms driver.
Remove this local config option and use the top level DRM_FBDEV_EMULATION
config option where applicable. Using this config lets us also prevent
wrapping around drm_fb_helper_* calls with #ifdefs in certain places.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1445933459-5249-2-git-send-email-architt@codeaurora.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bunch of things have been removed meanwhile and docs not fully
brought up to speed. And a few gaps closed where I noticed missing
kerneldoc while reading through the overview sections.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445533889-7661-3-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I just realized that I've forgotten to update all the gem refcounting
docs. For pennance also add pretty docs for the overall drm_gem_object
structure, with a few links thrown in fore good.
As usually we need to make sure the kerneldoc reference is at most a
sect2 for otherwise it won't be listed.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445533889-7661-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per the Vybrid Reference Manual (section 3.8.6.1), dspi0 has 6 chip
select signals associated with it, while dspi1 has only 4.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We have a machine Dell XPS 13 with the codec alc256, after resume back
from S3, the headphone has noise when play sound.
Through comparing with the coeff vaule before and after S3, we found
restoring a coeff register will help remove noise.
BugLink: https://bugs.launchpad.net/bugs/1519168
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We had seen lots of reports of this kind issue, so add one
warnning in blk-merge, then it can be triggered easily and
avoid to depend on warning/bug from drivers.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit bdced438acd83a(block: setup bi_phys_segments after
splitting) introduces function of computing bio->bi_phys_segments
during bio splitting.
Unfortunately both bio->bi_seg_front_size and bio->bi_seg_back_size
arn't computed, so too many physical segments may be obtained
for one request since both the two are used to check if one segment
across two bios can be possible.
This patch fixes the issue by computing the two variables in
blk_bio_segment_split().
Fixes: bdced438acd83a(block: setup bi_phys_segments after splitting)
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Inside blk_bio_segment_split(), previous bvec pointer(bvprvp)
always points to the iterator local variable, which is obviously
wrong, so fix it by pointing to the local variable of 'bvprv'.
Fixes: 5014c311baa2b(block: fix bogus compiler warnings in blk-merge.c)
Cc: stable@kernel.org #4.3
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A truncated cb_compound request will cause the client to decode null or
data from a previous callback for nfs4.1 backchannel case, or uninitialized
data for the nfs4.0 case. This is because the path through
svc_process_common() advances the request's iov_base and decrements iov_len
without adjusting the overall xdr_buf's len field. That causes
xdr_init_decode() to set up the xdr_stream with an incorrect length in
nfs4_callback_compound().
Fixing this for the nfs4.1 backchannel case first requires setting the
correct iov_len and page_len based on the length of received data in the
same manner as the nfs4.0 case.
Then the request's xdr_buf length can be adjusted for both cases based upon
the remaining iov_len and page_len.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If clp->cl_cb_ident is zero, then nfs_cb_idr_remove_locked() skips removing
it when the nfs_client is freed. A decoding or server bug can then find
and try to put that first nfs_client which would lead to a crash.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: d687031265 ("nfs4client: convert to idr_alloc()")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When LAYOUTGET gets NFS4ERR_DELAY, we currently will wait 15s before
retrying the call. That is a _very_ long time, so add a timeout value to
struct nfs4_layoutget and pass nfs4_async_handle_error a pointer to it.
This allows the RPC engine to use a sliding delay window, instead of a
15s delay.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
NFS v4.2 operations can work outside of pNFS, so dprintk() output
shouldn't be placed under NFSDBG_PNFS.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The NFS CLONE_RANGE defintion was wrong and thus never worked. Fix this
by simply using the btrfs ioctl defintion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Originally CLONE didn't allow for intra-file clones, but we recently
updated the spec to support this feature which is also supported by
local Linux file systems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Without this for example 64-bit binaries on typical amd64 distributions
would not be able to use ioctls on NFS. For now this only affects clones.
Additionally ->compat_ioctl is defined even for non-compat builds, so
get rid of the pointless ifdef.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Currently we pass uninitialized stack garbage in the count parameter.
The value is usually large enought to clone whole files and thus let
simple tests pass, but it makes the tests for range clones very unhappy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The following test program from Dmitry can cause softlockups or RCU
stalls as it copies 1GB from tmpfs into eventfd and we don't have any
scheduling point at that path in sendfile(2) implementation:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
Add cond_resched() into __splice_from_pipe() to fix the problem.
CC: Dmitry Vyukov <dvyukov@google.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 296291cdd1 (mm: make sendfile(2) killable) fixed an issue where
sendfile(2) was doing a lot of tiny writes into a filesystem and thus
was unkillable for a long time. However sendfile(2) can be (mis)used to
issue lots of writes into arbitrary file descriptor such as evenfd or
similar special file descriptors which never hit the standard filesystem
write path and thus are still unkillable. E.g. the following example
from Dmitry burns CPU for ~16s on my test system without possibility to
be killed:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
There are actually quite a few tests for pending signals in sendfile
code however we data to write is always available none of them seems to
trigger. So fix the problem by adding a test for pending signal into
splice_from_pipe_next() also before the loop waiting for pipe buffers to
be available. This should fix all the lockup issues with sendfile of the
do-ton-of-tiny-writes nature.
CC: stable@vger.kernel.org
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The thing got broken back in 2002 - sysvfs does *not* have inline
symlinks; even short ones have bodies stored in the first block
of file. sysv_symlink() handles that correctly; unfortunately,
attempting to look an existing symlink up will end up confusing
them for inline symlinks, and interpret the block number containing
the body as the body itself.
Nobody has noticed until now, which says something about the level
of testing sysvfs gets ;-/
Cc: stable@vger.kernel.org # all of them, not that anyone cared
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP which
is valid for all IMX6 SoC's (despite the fact that the IMXSDLRM and
IMXSXRM do not document this - this has been proven via tests as well as
verified by Freescale FAE).
Instead of assuming a fixed 85C for passive cooling threshold and 105C for
critical use the thermal grade for these configurations.
We will set the critical to maxT - 5C and passive to maxT - 10C.
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
----
v3:
- rebase against linux-soc-thermal.git
- added ack's from Shawn and Jon
v2:
- remove check for IMX6Q and update comments: The OTP values have been tested
on IMX6SOLO, IMX6DUALLITE, and IMX6SX and Freescale FAE has shared data with
me that the OTP settings are the same and that the reference manuals will
reflect this in their next updates.
- set critical to max - 5C
- set passive to max - 10C
- display max temp in info
- do not allow passive to be set above critical
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When the prototype for thermal_zone_bind_cooling_device
changed, the static inline wrapper function was left alone,
which in theory can cause build warnings:
I have seen this error in the past:
drivers/thermal/db8500_thermal.c: In function 'db8500_cdev_bind':
drivers/thermal/db8500_thermal.c:78:9: error: too many arguments to function 'thermal_zone_bind_cooling_device'
ret = thermal_zone_bind_cooling_device(thermal, i, cdev,
while this one no longer shows up, there is no doubt that
the prototype is still wrong, so let's just fix it anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6cd9e9f629 ("thermal: of: fix cooling device weights in device tree")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This just caused build errors:
warning: (QCOM_SPMI_TEMP_ALARM) selects REGMAP_SPMI which has unmet direct dependencies (SPMI)
drivers/built-in.o: In function `regmap_spmi_ext_gather_write':
:(.text+0x609b0): undefined reference to `spmi_ext_register_write'
:(.text+0x609f0): undefined reference to `spmi_ext_register_writel'
While it's generally a good idea to allow compile testing, in this
case, it just doesn't work, so reverting the patch that
introduced the compile-test variant seems the most appropriate
solution.
Note that SPMI also has a 'depends on ARCH_QCOM || COMPILE_TEST'
statement, so we should be able to enable SPMI on all architectures
for compile testing already.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: cb7fb4d342 ("thermal: qcom_spmi: allow compile test")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The SCPI clk driver registers the virtual cpufreq device that kicks off
initialisation of the SCPI cpufreq driver. Also, clk_get() will fail for
the cpufreq driver if the SCPI clk driver is missing.
Fix this by making the SCPI cpufreq driver explicitly depend on the SCPI
clk driver.
Fixes: 8def31034d (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A rounding error was found in the calculation of limits->max_perf
in intel_pstate_set_policy(), which is used to calculate the max and min
pstate values in intel_pstate_get_min_max(). In that code,
limits->max_perf is truncated to 2 hex digits such that, for example,
0x169 was incorrectly calculated to 0x16 instead of 0x17. This resulted in
the pstate being set one level too low. This patch rounds the value of
limits->max_perf up instead of down so that the correct max pstate can
be reached.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I have a Intel (6,63) processor with a "marketing" frequency (from
/proc/cpuinfo) of 2100MHz, and a max turbo frequency of 2600MHz. I
can execute
cpupower frequency-set -g powersave --min 1200MHz --max 2100MHz
and the max_freq_pct is set to 80. When adding load to the system I noticed
that the cpu frequency only reached 2000MHZ and not 2100MHz as expected.
This is because limits->max_policy_pct is calculated as 2100 * 100 /2600 = 80.7
and is rounded down to 80 when it should be rounded up to 81. This patch
adds a DIV_ROUND_UP() which will return the correct value.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Subsys interface's ->remove_dev() is called when the cpufreq driver is
unregistering or the CPU is getting physically removed. We keep removing
the cpuX/cpufreq link for all CPUs except the last one, which is a
mistake as all CPUs contain a link now.
Because of this, one CPU from each policy will still contain a link (to
an already removed policyX directory), after the cpufreq driver is
unregistered.
Fix that by removing the link first and then only see if the policy is
required to be freed. That will make sure that no links are left out.
Fixes: 96bdda61f5 ("cpufreq: create cpu/cpufreq/policyX directories")
Reported-and-tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CPU policy struct indicates the co-ordination type
for all CPUs of a common freq domain. Initialize it
correctly using the CPU specific data gathered from
CPPC ACPI lib via acpi_get_psd_map().
The PSD object is optional, so the cpu->shared_type
can also be 0. So instead of assuming any value other
than SW_ANY(0xFD) is unsupported, explictly check
if shared_type is SW_ALL and then bail.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This update consists of one minor documentation fix and a fix
to an existing test.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8sYr
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update consists of one minor documentation fix and a fix to an
existing test"
* tag 'linux-kselftest-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/seccomp: Get page size from sysconf
tools:testing/selftests: fix typo in futex/README
When establishing a thin device's discard limits we cannot rely on the
underlying thin-pool device's discard capabilities (which are inherited
from the thin-pool's underlying data device) given that DM thin devices
must provide discard support even when the thin-pool's underlying data
device doesn't support discards.
Users were exposed to this thin device discard limits regression if
their thin-pool's underlying data device does _not_ support discards.
This regression caused all upper-layers that called the
blkdev_issue_discard() interface to not be able to issue discards to
thin devices (because discard_granularity was 0). This regression
wasn't caught earlier because the device-mapper-test-suite's extensive
'thin-provisioning' discard tests are only ever performed against
thin-pool's with data devices that support discards.
Fix is to have thin_io_hints() test the pool's 'discard_enabled' feature
rather than inferring whether or not a thin device's discard support
should be enabled by looking at the thin-pool's discard_granularity.
Fixes: 216076705 ("dm thin: disable discard support for thin devices if pool's is disabled")
Reported-by: Mike Gerber <mike@sprachgewalt.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.1+
Currently kernel crash randomly when K2L EVM is booted without
clk_ignore_unused in the bootargs. This workaround is not needed
on other K2 devices such as K2HK and K2E and with this fix, we can
remove the workaround altogether. netcp driver on K2L uses linked
ram on OSR (On chip Static RAM) and requires the clock to this peripheral
enabled for proper functioning. This is the reason for the kernel crash.
So add the clock node to fix this issue.
While at it, remove the workaround documentation as well.
With the fix applied, clk_summary dump shows the clock to OSR enabled.
cat /sys/kernel/debug/clk/clk_summary
------cut--------------
tcp3d-1 0 0 399360000 0 0
tcp3d-0 0 0 399360000 0 0
osr 1 1 399360000 0 0
fftc-0 0 0 399360000 0 0
-----cut----------------
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Configure linking RAM for both queue managers also in case
when only linking RAM 0 is specified in device tree.
Currently hwqueue driver configures linking RAM(s) to be used
cooperatively by the QMs (shared mode). Therefore if both
queue managers are used then both must be configured with
exactly the same linking RAM info (base address and size)
independent of the number of linking RAM(s) specified in the
device tree.
For proper operation only one linking RAM is required and in most
cases this can be internal one as long as it is able to handle
the number of descriptors used in the system.
Current driver code however skips configuration of second
queue manager if second linking RAM is not specified.
If the configuration for the QM2 is missing there will be
a crash when it tries to push/pop descriptors from its queues.
Signed-off-by: Michal Morawiec <michal.1.morawiec.ext@nokia.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Marc Zyngier