When we sync the RX queues the driver waits to receive echo
notification on all the RX queues.
The wait queue is set with timeout until all queues have received
the notification.
However, iwl_mvm_rx_queue_notif() never woke up the wait queue,
with the result of the counter value being checked only when the
timeout expired.
This may cause a latency of up to 1 second.
Fixes: 0636b93821 ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the suspend flow fails, we restart the hardware to go back to
the D0 image (with non-unified images), but we don't comply with
the fw_restart module parameter. If something goes wrong when
starting the D3 image, we may want to debug it, so we should
comply with the fw_restart flag to avoid clearing everything up
and losing the firmware state when the error occurred.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a unified D0/D3 image is used, we don't restart the FW in the
D0->D3->D0 transitions. Therefore, the d3_test functionality should
not call ieee8021_restart_hw() when the resuming either.
Fixes: commit 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_dbgfs_mem_read(), the len variable may become negative and is
compared to < 0 (an error case). Comparing size_t (which is unsigned)
to < 0 causes a warning on certain platforms (like i386):
drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c:1561:5-8: WARNING: Unsigned expression compared with zero: len < 0
To prevent that, use ssize_t for len instead.
Fixes: commit 2b55f43f8e ("iwlwifi: mvm: Add mem debugfs entry")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel reports that when CMD_WANT_ASYNC_CALLBACK is used by mvm,
the callback will be called with the command queue lock held, and
mvm will try to stop all (other) TX queues, which acquires their
locks - this caused a false lockdep recursive locking report.
Suppress this report by marking the command queue lock with a new,
separate, lock class so lockdep can tell the difference between
the two types of queues.
Fixes: 156f92f2b4 ("iwlwifi: block the queues when we send ADD_STA for uAPSD")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
SDIO ID 0271:0418
Signed-off-by: Alan Cox <alan@linux.intel.com>
Bugzilla-ID: https://bugzilla.kernel.org/show_bug.cgi?id=67921
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit 171f6402e4 ("ath9k_hw: implement temperature compensation
support for AR9003+"). Some users report that this commit causes a regression
in performance under some conditions.
Fixes: 171f6402e4 ("ath9k_hw: implement temperature compensation support for AR9003+")
Cc: <stable@vger.kernel.org> # 4.8
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 0b8e3c4ca2 ("ath10k: move cal data len to hw_params") broke retrieving
the calibration data from cal_data debugfs file. The length of file was always
zero. The reason is:
static ssize_t ath10k_debug_cal_data_read(struct file *file,
char __user *user_buf,
size_t count, loff_t *ppos)
{
struct ath10k *ar = file->private_data;
void *buf = file->private_data;
This is obviously bogus, private_data cannot contain both struct ath10k and the
buffer. Fix it by caching calibration data to ar->debug.cal_data. This also
allows it to be accessed when the device is not active (interface is down).
The cal_data buffer is fixed size because during the first firmware probe we
don't yet know what will be the lenght of the calibration data. It was simplest
just to use a fixed length. There's a WARN_ON() in
ath10k_debug_cal_data_fetch() if the buffer is too small.
Tested with qca988x and firmware 10.2.4.70.56.
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Fixes: 0b8e3c4ca2 ("ath10k: move cal data len to hw_params")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
[kvalo@qca.qualcomm.com: improve commit log and minor other changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit d86e647688 ("rtlwifi: rtl818x: constify local structures"),
the configuration struct for most of the drivers was changed to be
constant. The problem is that five of the modified drivers need to be
able to update the firmware name based on the exact model of the card.
As the file names were stored in one of the members of that struct,
these drivers would fail with a kernel BUG splat when they tried to
update the firmware name.
Rather than reverting the previous commit, I used a suggestion by
Johannes Berg and made the firmware file name pointers be local to
the routines that update the software variables.
The configuration struct of rtl8192cu, which was not touched in the
previous patch, is now constantfied.
Fixes: d86e647688 ("rtlwifi: rtl818x: constify local structures")
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.8
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu suffered from two issues when reloading the driver.
The same problems as with the 8723bu where REG_RX_WAIT_CCA bits 22 and
23 didn't get set in rtl8192e_enable_rf().
In addition it also seems prone to issues when setting REG_RF_CTRL to
0 intead of just disabling the RF_ENABLE bit. Similar to what was
causing issues with the 8188eu.
With this patch I can successfully reload the driver and reassociate
to an APi with an 8192eu dongle.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The generic disable_rf() function clears bits 22 and 23 in
REG_RX_WAIT_CCA, however we did not re-enable them again in
rtl8723b_enable_rf()
This resolves the problem for me with 8723bu devices not working again
after reloading the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The full RX descriptor is converted so converting tsfl again would
return it to it's original endian value.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A device running without RX package aggregation could return more data
in the USB packet than the actual network packet. In this case we
could would clone the skb but then determine that that there was no
packet to handle and exit without freeing the cloned skb first.
This has so far only been observed with 8188eu devices, but could
affect others.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's not necessary to free memory allocated with devm_kzalloc
and using kfree leads to a double free.
Fixes: d776fc86b8 ("wlcore: sdio: Populate config firmware data")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jiri Pirko says:
====================
mlxsw: Couple of fixes
Couple of fixes from Yotam.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to specify that the mlxsw switchx2 driver needs additional
headroom for packets, there have been use of the hard_header_len field of
the netdevice struct.
This commit changes that to use needed_headroom instead, as this is the
correct way to do that.
Fixes: 31557f0f97 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to specify that the mlxsw spectrum driver needs additional
headroom for packets, there have been use of the hard_header_len field of
the netdevice struct.
This commit changes that to use needed_headroom instead, as this is the
correct way to do that.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Neighbor Awareness Networking (NAN) APIs
* a fix for a previous patch that caused memory corruption
in wireless extensions key settings
* beacon rate configuration for AP and mesh
* memory limits for mac80211's internal TXQs
* a (fairly involved) fix for the TXQ vs. crypto problems
* direct cfg80211 driver API for WEP keys
This also pulls in net-next to fix the merge conflicts, see
the merge commit for more details.
-----BEGIN PGP SIGNATURE-----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=qTne
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-10-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time around, we have
* Neighbor Awareness Networking (NAN) APIs
* a fix for a previous patch that caused memory corruption
in wireless extensions key settings
* beacon rate configuration for AP and mesh
* memory limits for mac80211's internal TXQs
* a (fairly involved) fix for the TXQ vs. crypto problems
* direct cfg80211 driver API for WEP keys
This also pulls in net-next to fix the merge conflicts, see
the merge commit for more details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve the merge conflict between Felix's/my and Toke's patches
coming into the tree through net and mac80211-next respectively.
Most of Felix's changes go away due to Toke's new infrastructure
work, my patch changes to "goto begin" (the label wasn't there
before) instead of returning NULL so flow control towards drivers
is preserved better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Gavin Shan says:
====================
net/ncsi: NCSI Improvment and bug fixes
This series of patches improves NCSI stack according to the comments
I received after the NCSI code was merged to 4.8.rc1:
* PATCH[1/8] fixes the build warning caused by xchg() with ia64-linux-gcc.
The atomic operations are removed. The NCSI's lock should be taken when
reading or updating its state and chained state.
* Channel ID (0x1f) is the reserved one and it cannot be valid channel ID.
So we needn't try to probe channel whose ID is 0x1f. PATCH[2/8] and
PATCH[3/8] are addressing this issue.
* The request IDs are assigned in round-robin fashion, but it's broken.
PATCH[4/8] make it work.
* PATCH[5/8] and PATCH[6/8] reworks the channel monitoring to improve the
code readability and its robustness.
* PATCH[7/8] and PATCH[8/8] introduces ncsi_stop_dev() so that the network
device can be closed and opened afterwards. No error will be seen.
Changelog
=========
v2:
* The NCSI's lock is taken when reading or updating its state as the
{READ,WRITE}_ONCE() isn't reliable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This stops NCSI device when closing the network device so that the
NCSI device can be reenabled later.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces ncsi_stop_dev(), as counterpart to ncsi_start_dev(),
to stop the NCSI device so that it can be reenabled in future. This
API should be called when the network device driver is going to
shutdown the device. There are 3 things done in the function: Stop
the channel monitoring; Reset channels to inactive state; Report
NCSI link down.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original NCSI channel monitoring was implemented based on a
backoff algorithm: the GLS response should be received in the
specified interval. Otherwise, the channel is regarded as dead
and failover should be taken if current channel is an active one.
There are several problems in the implementation: (A) On BCM5718,
we found when the IID (Instance ID) in the GLS command packet
changes from 255 to 1, the response corresponding to IID#1 never
comes in. It means we cannot make the unfair judgement that the
channel is dead when one response is missed. (B) The code's
readability should be improved. (C) We should do failover when
current channel is active one and the channel monitoring should
be marked as disabled before doing failover.
This reworks the channel monitoring to address all above issues.
The fields for channel monitoring is put into separate struct
and the state of channel monitoring is predefined. The channel
is regarded alive if the network controller responses to one of
two GLS commands or both of them in 5 seconds.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is only one NCSI request property for now: the response for
the sent command need drive the workqueue or not. So we had one
field (@driven) for the purpose. We lost the flexibility to extend
NCSI request properties.
This replaces @driven with @flags and @req_flags in NCSI request
and NCSI command argument struct. Each bit of the newly introduced
field can be used for one property. No functional changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCSI request index (struct ncsi_request::id) is put into instance
ID (IID) field while sending NCSI command packet. It was designed the
available IDs are given in round-robin fashion. @ndp->request_id was
introduced to represent the next available ID, but it has been used
as number of successively allocated IDs. It breaks the round-robin
design. Besides, we shouldn't put 0 to NCSI command packet's IID
field, meaning ID#0 should be reserved according section 6.3.1.1
in NCSI spec (v1.1.0).
This fixes above two issues. With it applied, the available IDs will
be assigned in round-robin fashion and ID#0 won't be assigned.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We needn't send CIS (Clear Initial State) command to the NCSI
reserved channel (0x1f) in the enumeration. We shouldn't receive
a valid response from CIS on NCSI channel 0x1f.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This defines NCSI_RESERVED_CHANNEL as the reserved NCSI channel
ID (0x1f). No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
xchg() is used to set NCSI channel's state in order for consistent
access to the state. xchg()'s return value should be used. Otherwise,
one build warning will be raised (with -Wunused-value) as below message
indicates. It is reported by ia64-linux-gcc (GCC) 4.9.0.
net/ncsi/ncsi-manage.c: In function 'ncsi_channel_monitor':
arch/ia64/include/uapi/asm/cmpxchg.h:56:2: warning: value computed is \
not used [-Wunused-value]
((__typeof__(*(ptr))) __xchg((unsigned long) (x), (ptr), sizeof(*(ptr))))
^
net/ncsi/ncsi-manage.c:202:3: note: in expansion of macro 'xchg'
xchg(&nc->state, NCSI_CHANNEL_INACTIVE);
This removes the atomic access to NCSI channel's state avoid the above
build warning. We have to hold the channel's lock when its state is readed
or updated. No functional changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a respin of a patch to fix a relatively easily reproducible kernel
panic related to the all_adj_list handling for netdevs in recent kernels.
The following sequence of commands will reproduce the issue:
ip link add link eth0 name eth0.100 type vlan id 100
ip link add link eth0 name eth0.200 type vlan id 200
ip link add name testbr type bridge
ip link set eth0.100 master testbr
ip link set eth0.200 master testbr
ip link add link testbr mac0 type macvlan
ip link delete dev testbr
This creates an upper/lower tree of (excuse the poor ASCII art):
/---eth0.100-eth0
mac0-testbr-
\---eth0.200-eth0
When testbr is deleted, the all_adj_lists are walked, and eth0 is deleted twice from
the mac0 list. Unfortunately, during setup in __netdev_upper_dev_link, only one
reference to eth0 is added, so this results in a panic.
This change adds reference count propagation so things are handled properly.
Matthias Schiffer reported a similar crash in batman-adv:
https://github.com/freifunk-gluon/gluon/issues/680https://www.open-mesh.org/issues/247
which this patch also seems to resolve.
Signed-off-by: Andrew Collins <acollins@cradlepoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edge-rate:
As system and networking speeds increase, a signal's output transition,
also know as the edge rate or slew rate (V/ns), takes on greater importance
because high-speed signals come with a price. That price is an assortment of
interference problems like ringing on the line, signal overshoot and
undershoot, extended signal settling times, crosstalk noise, transmission
line reflections, false signal detection by the receiving device and
electromagnetic interference (EMI) -- all of which can negate the potential
gains designers are seeking when they try to increase system speeds through
the use of higher performance logic devices. The fact is, faster signaling
edge rates can cause a higher level of electrical noise or other type of
interference that can actually lead to slower line speeds and lower maximum
system frequencies. This parameter allow the board designers to change the
driving strange, and thereby change the EMI behavioral.
Edge-rate parameters (vddmac, edge-slowdown) get from Device Tree.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3_reset_work() expects tx queues to be stopped (via
vmxnet3_quiesce_dev -> netif_tx_disable). However, this races with the
netif_wake_queue() call in netif_tx_timeout() such that the driver's
start_xmit routine may be called unexpectedly, triggering one of the BUG_ON
in vmxnet3_map_pkt with a stack trace like this:
RIP: 0010:[<ffffffffa00cf4bc>] vmxnet3_map_pkt+0x3ac/0x4c0 [vmxnet3]
[<ffffffffa00cf7e0>] vmxnet3_tq_xmit+0x210/0x4e0 [vmxnet3]
[<ffffffff813ab144>] dev_hard_start_xmit+0x2e4/0x4c0
[<ffffffff813c956e>] sch_direct_xmit+0x17e/0x1e0
[<ffffffff813c96a7>] __qdisc_run+0xd7/0x130
[<ffffffff813a6a7a>] net_tx_action+0x10a/0x200
[<ffffffff810691df>] __do_softirq+0x11f/0x260
[<ffffffff81472fdc>] call_softirq+0x1c/0x30
[<ffffffff81004695>] do_softirq+0x65/0xa0
[<ffffffff81069b89>] local_bh_enable_ip+0x99/0xa0
[<ffffffffa031ff36>] destroy_conntrack+0x96/0x110 [nf_conntrack]
[<ffffffff813d65e2>] nf_conntrack_destroy+0x12/0x20
[<ffffffff8139c6d5>] skb_release_head_state+0xb5/0xf0
[<ffffffff8139d299>] skb_release_all+0x9/0x20
[<ffffffff8139cfe9>] __kfree_skb+0x9/0x90
[<ffffffffa00d0069>] vmxnet3_quiesce_dev+0x209/0x340 [vmxnet3]
[<ffffffffa00d020a>] vmxnet3_reset_work+0x6a/0xa0 [vmxnet3]
[<ffffffff8107d7cc>] process_one_work+0x16c/0x350
[<ffffffff810804fa>] worker_thread+0x17a/0x410
[<ffffffff810848c6>] kthread+0x96/0xa0
[<ffffffff81472ee4>] kernel_thread_helper+0x4/0x10
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2016-10-02
This series contains updates to fm10k only.
Jake fixes an issue where PTP applications requesting software timestamps
may complain that the requested mode is not supported, so add a generic
callback for those drivers that have software transmit timestamp support
enabled. Then provides a trivial cleanup where a code was not wrapped
properly. Got make sure that code looks good in a 80 character limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.
The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.
Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:
[549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
[549.664] i40e: probe of 0007:01:00.1 failed with error -15
[...]
[871.644] i40e 0007:01:00.1: The driver for the device stopped because the
device firmware failed to init. Try updating your NVM image.
[871.644] i40e: probe of 0007:01:00.1 failed with error -32
[...]
[872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored
Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.
This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.
CC: <stable@vger.kernel.org>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-10-03
This series contains fixes to i40e only.
Stefan Assmann provides the changes in this series to resolve an issue
where when we run out of MSIx vectors, iWARP gets disabled automatically.
First adds a check for "no vectors left" during MSIx vector allocation
for VMDq, which will prevent more vectors being allocated than available.
Then fixed the MSIx vector redistribution when we reach the hardware limit
for vectors so that additional features like VMDq, iWARP, etc do not get
starved for vectors because the PF is hogging all the resources. Lastly,
fix the issue for flow director by moving the check for the reaching the
vector limit earlier in the code so that a decision can be made on
disabling flow director.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed*: Add qedr infrastructure support
In the last couple of weeks we've been sending RFCs for the qedr
driver - the RoCE driver for QLogic FastLinQ 4xxxx line of adapters.
Latest RFC can be found at [1].
At Doug's advice [2], we've decided to split the series into two:
- first part contains the qed backbone that's necessary for all the
configurations relating to the qedr driver, as well as the qede
infrastructure that is used for communication between the qedr and qede.
- Second part consists of the actual qedr driver and introduces almost
no changes to qed/qede.
This is the first of said two parts. The second half would be sent
later this week.
The only 'oddity' in the devision are the Kconfig options -
As this series introduces both LL2 and QEDR-based logic in qed/qede,
I wanted to add the CONFIG_INFINIBAND_QEDR option here [with default n].
Otherwise, a lot of the code introduced would be dead-code [won't even
be compiled] until qedr is accepted.
As a result I've placed the config option in an odd place - under
qlogic's Kconfig. The second series would then remove that option
and add it in its correct place under the infiniband Kconfig.
[I'm fine with pushing it there to begin with, but I didn't want to
'contaminate' non-qlogic configuration files with half-baked options].
Dave - I don't think you were E-mailed with Doug's suggestion.
I think the notion was to have the two halves accepted side-by-side,
but actually the first has no dependency issues, so it's also
possible to simply take this first to net-next, and push the qedr
into rdma once it's merged. But it's basically up to you and Doug;
We'd align with whatever suits you best.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the RoCE-specific LL2 logic [as well as GSI support] over
the 'generic' LL2 interface.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add slowpath configuration support for user, dma and memory
regions registration.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the slowpath configurations of Queue Pair verbs
which adds, deletes, modifies and queries Queue Pairs.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the configurations of the protection domain and
completion queues.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the qedr driver - FW notification, resource
initializations, etc.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a skeletal implementation of the qede RoCE driver -
The qedr has some dependencies of the state of the underlying base
interface. This adds some logic required with mutual registrations
and the ability to pass updates on 'intresting' events.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other protocols beside the networking driver need the ability
of passing some L2 traffic, usually [although not limited] for the
purpose of some management traffic.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if the MSI-X vector limit is reached the sideband flow
director gets disabled. A bit too early to make that decision, as
vectors may get re-distributed. So move the check further back.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver allocates 1 vector per CPU thread and the current hardware
limit for vectors is 129 per PF. On systems with 128 or more threads
this currently means all vectors are used by the PF leaving no room for
additional features like VMDq, iWARP, etc...
The code that should redistribute the vectors in this case is broken and
never triggers. Fixed the code so that it actually triggers if the
hardware limit is reached and adjust the number of queue pairs
accordingly.
Also the number of initially requested iWARP vectors was not properly
saved when the vector limit was reached, and therefore always zero.
Comparison with debug statement.
Before:
i40e 0000:2d:00.0: VMDq disabled, not enough MSI-X vectors
i40e 0000:2d:00.0: IWARP disabled, not enough MSI-X vectors
i40e 00.0 MSI-X vector distribution: PF 128, VMDq 0, FDSB 0, iWARP 0
After:
i40e 0000:2d:00.0: MSI-X vector limit reached, attempting to redistribute vectors
i40e 00.0 MSI-X vector distribution: PF 78, VMDq 8, FDSB 0, iWARP 42
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During MSI-X vector allocation for VMDq, a check for "no vectors left"
was missing, add it. This prevents more vectors to be allocated than
available.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A call to 'ida_simple_remove()' is missing in the error handling path.
This as been spotted with the following coccinelle script which tries to
detect missing 'ida_simple_remove()' call in error handling paths.
///////////////
@@
expression x;
identifier l;
@@
* x = ida_simple_get(...);
...
if (...) {
...
}
...
if (...) {
...
goto l;
}
...
* l: ... when != ida_simple_remove(...);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Also add check for return value of platform_get_resource().
Fixes: 54e19bc74f ("net: qcom/emac: do not use devm on internal
phy pdev")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_vlan_pop/push were too generic, trying to support the cases where
skb->data is at mac header, and cases where skb->data is arbitrarily
elsewhere.
Supporting an arbitrary skb->data was complex and bogus:
- It failed to unwind skb->data to its original location post actual
pop/push.
(Also, semantic is not well defined for unwinding: If data was into
the eth header, need to use same offset from start; But if data was
at network header or beyond, need to adjust the original offset
according to the push/pull)
- It mangled the rcsum post actual push/pop, without taking into account
that the eth bytes might already have been pulled out of the csum.
Most callers (ovs, bpf) already had their skb->data at mac_header upon
invoking skb_vlan_pop/push.
Last caller that failed to do so (act_vlan) has been recently fixed.
Therefore, to simplify things, no longer support arbitrary skb->data
inputs for skb_vlan_pop/push().
skb->data is expected to be exactly at mac_header; WARN otherwise.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Pravin Shelar <pshelar@ovn.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generic skb_vlan_push/skb_vlan_pop functions don't properly handle the
case where the input skb data pointer does not point at the mac header:
- They're doing push/pop, but fail to properly unwind data back to its
original location.
For example, in the skb_vlan_push case, any subsequent
'skb_push(skb, skb->mac_len)' calls make the skb->data point 4 bytes
BEFORE start of frame, leading to bogus frames that may be transmitted.
- They update rcsum per the added/removed 4 bytes tag.
Alas if data is originally after the vlan/eth headers, then these
bytes were already pulled out of the csum.
OTOH calling skb_vlan_push/skb_vlan_pop with skb->data at mac_header
present no issues.
act_vlan is the only caller to skb_vlan_*() that has skb->data pointing
at network header (upon ingress).
Other calles (ovs, bpf) already adjust skb->data at mac_header.
This patch fixes act_vlan to point to the mac_header prior calling
skb_vlan_*() functions, as other callers do.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Pravin Shelar <pshelar@ovn.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial change here to cleanup a checkpatch.pl warning that got
introduced when changing to alloc_workqueue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sara Sharon