Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SLI related fixes:
- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invalid RPI. (126350)
- Fix reset port when reset is needed during fw_dump (125807)
- Fix unbounded firmware revision string from port cause panic (126560)
- Fix driver behavior when receiving an ADISC (126654)
- Fix driver not returning when bad ndlp found in abts error event
handling (126209)
- Add more driver logs in area of SLI4 port error attention and reset
recovery (126813, 124466)
- Fix failure in handling large CQ/EQ identifiers in an IOV
environment (126856)
- Fix for driver using duplicate RPIs after lancer port reset (126723)
- Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a
zero SID (126779, 126897)
- Fix for SLI4 Port delivery for BLS ABORT ACC (126289)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Make lpfc_sli4_pci_mem_unset interface type aware (CR 124390)
- Convert byte count to word count when calling __iowrite32_copy (CR 122550)
- Checked the ERR1 and ERR2 registers for error attention due to SLI
Port state affected by forced debug dump. (CR 122986, 122426, 124859)
- Use the lpfc_readl routine instead of the readl for the port status
register read in lpfc_handle_eratt_s4 (CR 125403)
- Call lpfc_sli4_queue_destroy inside of lpfc_sli4_brdreset before doing
a pci function reset (CR 125124, 125168, 125572, 125622)
- Zero out the HBQ when it is allocated (CR 125663)
- Alter port reset log messages to indicate error type (CR 125989)
- Added proper NULL pointer checking to all the places that accessing
the queue memory (CR 125832)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adapter (SLI) interface fixes:
- Modify WQ handling to use entry_repost (CR 123981)
- Fix for ABTS. Do not free original IOCB whenever ABTS fails. (CR 115829)
- Check board for FCoE before reading FCoE paramaters (CR124731)
- Add support for SLI4 FC Loop mode (CR 124721)
- Add support for resource count changes during fw reset. (CR 125888, 125675)
- Increase CQE count from 256 to 1024. (CR 126149)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implemented new algorithm for getting physical port name for all SLI4 devices
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changed the timeout value for flash-based SLI_CONFIG (0x9B)
mailbox command to 300 seconds for worst case flash delays.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellanous logic and interface fixes
- Fix lpfc_init_vfi_cmpl to check the interface type for interface type 0
before parsing the results.
- Cast uint32_t values that are multiplied to uint64_t before the
multiplication.
- Instead of "break" statement when PCI read returned error, use the goto
statement to the end of the routine after setting return value
- moved the msleep(10) to the beginning of the wait loop for checking the
SLIPort_Status register
- Added the code to follow the existing wait for SLIPort_Status register RDY,
ERR, and RN bits to be set by the port before proceeding to perform PCI
function reset.
- Do not override ulpCt_h and ulpCt_l for SLI 4 ports.
- For vport delete, call lpfc_nlp_put when the vport's vpi state is not
marked with VPI_REGISTERED.
- Added missed fields into the driver's Controller Attributes Structure
- Changed ringing EQ/CQ/RQ doorbell register to be dependent on the size
of the queue.
- Return -EACCES in issue_reset if cfg_enable_hba_reset is zero.
- Added new logging flag LOG_FCP_UNDER 0x00040000 to qualify underrun logging.
- Add a check in the fabric name display routine to display 0 if the port
state is <= FLOGI.
- Add a check to the switch statement in lpfc_decode_firmware_rev to check
for an 'X'.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch implements a new FCF failover policy for the lpfc driver. It
allows the driver to choose which FCF to failover to based on the FCF
priority. This patch also introduces a new sysfs parameter
(fcf_failover_policy) to allow the user to choose which FCF failover policy
to use.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellaneous Bug fixes and code cleanup
- Fix 16G link speed reporting by adding check for 16G check.
- Change the check and enforcement of MAILBOX_EXT_SIZE (2048B)
to the check and enforcement of BSG_MBOX_SIZE - sizeof(MAILBOX_t) (3840B).
- Instead of waiting for a fixed amount of time after performing firmware
reset, the driver shall wait for the Lancer SLIPORT_STATUS register for the
readiness of the firmware for bring up.
- Add logging to indicate when dynamic parameters are changed.
- Add revision and date to the firmware image format.
- Use revision instead of rev_name to check firmware image version.
- Update temporary offset after memcopy is complete for firmware update.
- Consolidated the use of the macros to get rid of duplicated register
offset definitions.
- Removed the unused second parameter in routine lpfc_bsg_diag_mode_enter()
- Enable debugfs when debugfs is enabled.
- Update function comments for lpfc_sli4_alloc_xri and lpfc_sli4_init_rpi_hdrs.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Update Copyright Dates
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add the driver debugfs framework for supporting debugfs read and write
operations, and iDiag command structure.
- Add read and write to SLI4 device PCI config space registers.
- Add the driver support of debugfs PCI config space register bits set/clear
methods to the provided bitmask.
- Add iDiag driver support for SLI4 device queue diagnostic.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
RRQ Implementation fixes
- Added checks to prevent a call to findnode_did in clr_active_rrq
- Added the del_sync_timer call for the rrq_tmr to the stop_hba_timers routine.
- Added a check in __lpfc_set_active_rrq for the driver unloading to prevent
adding an rrq when the driver is being removed.
- Add code to scsi_iocb_cmpl to check for the remote stop and add the rrq.
- Added the same check to els retry.
- Added code to compare the source did in the els rrq to the vports did and
chose the right exchange ID.
- Initialize the start_cmd pointer to indicate when we have looped through
all of the scsi buffers.
- Remove the need for the lock around the clearing of the active bit in the
rrq.
- Added code to clean the els and fcp xri aborted list and remove the all of
the RRQs for a deleted vport.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Critical Errors:
- Correctly handle non-zero return lpfc_workq_post_event and return ENOMEM
- Save the irq level when locking the host_lock in lpfc_findnode_did
Bug Fixes:
- Adjust payload_length and request_length for sli4_config mailbox commands.
- Add the freed sgl/XRI to the tail of the list rather than to the head.
- Set the FC_VPORT_NEEDS_INIT_VPI on vport deletes and check it before
issuing a fdisc on an els retry.
- Only call lpfc_hba_init_link() if phba->cfg_suppress_link_up
is LPFC_INITIALIZE_LINK.
- Add support for SLI-4 Performance Hints
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updated commands used for ELS to utilize VPI
Allocate RPI at node creation time and pass in ELS commnads.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement new SLI4 init procedures based on if_type:
- Add structure changes for new SLIPORT registers and BAR changes.
- Update register names to be consistent with inteface spec terms.
- Added union to encapsulate Hardward error registers.
- Rework lpfc_sli4_post_status_check() around SLI-4's SLI_INTF type
- Removed the lpfc_sli4_fw_cfg_check routine
- Segmented driver logic to include evaluation of the if_type to
engage different behaviors.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement the FC and SLI async event handlers:
- Updated MQ_CREATE_EXT mailbox structure to include fc and SLI async events.
- Added the SLI trailer code.
- Split physical field into type and number to reflect latest SLI spec.
- Changed lpfc_acqe_fcoe to lpfc_acqe_fip to reflect latest Spec changes.
- Added lpfc_acqe_fc_la structure for FC link attention async events.
- Added lpfc_acqe_sli structure for sli async events.
- Added lpfc_sli4_async_fc_evt routine to handle fc la async events.
- Added lpfc_sli4_async_sli routine to handle sli async events.
- Moved LPFC_TRAILER_CODE_FC to be handled by its own handler function.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added support for ELS RRQ command
- Add new routine lpfc_set_rrq_active() to track XRI qualifier state.
- Add new module parameter lpfc_enable_rrq to control RRQ operation.
- Add logic to ELS RRQ completion handler and xri qualifier timeout
to clear XRI qualifier state.
- Use OX_ID from XRI_ABORTED_CQE for RRQ payload.
- Tie abort and XRI_ABORTED_CQE andler to RRQ generation.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add SLI4 FC Discovery support
- Replace READ_LA and READ_LA64 with READ_TOPOLOGY mailbox command.
- Converted the old READ_LA structure to use bf_set/get instead of bit fields.
- Rename HBA_FCOE_SUPPORT flag to HBA_FCOE_MODE. Flag now indicates function
is running as SLI-4 FC or FCoE port. Make sure flag reset each time
READ_REV completed as it can dynamically change.
- Removed BDE union in the READ_TOPOLOGY mailbox command and added a define to
define the ALPA MAP SIZE. Added FC Code for async events.
- Added code to support new 16G link speed.
- Define new set of values to keep track of valid user settable link speeds.
- Used new link speed definitions to define link speed max and bitmap.
- Redefined FDMI Port sppeds to be hax values and added the 16G value.
- Added new CQE trailer code for FC Events.
- Add lpfc_issue_init_vfi and lpfc_init_vfi_cmpl routines.
- Replace many calls to the initial_flogi routine with lpfc_issue_init_vfi.
- Add vp and vpi fields to the INIT_VFI mailbox command.
- Addapt lpfc_hba_init_link routine for SLI4 use.
- Use lpfc_hba_init_link call from lpfc_sli4_hba_setup.
- Add a check for FC mode to register the FCFI before init link.
- Convert lpfc_sli4_init_vpi to be called without a vpi (get it from vport).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adapter Shutdown and Unregistration cleanup
- Correct the logic around hba shutdown. Prior to final reset, the
driver must wait for all XRIs to return from the adapter. Added logic
to poll, progressively slowing the poll rate as delay gets longer.
- Correct behavior around the rsvd1 field in UNREG_RPI_ALL mailbox
completion and final rpi cleanup.
- Updated logic to move pending VPI registrations to their completion
in cases where a CVL may be received while registration in progress.
- Added unreg all rpi mailbox command before unreg vpi.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added driver logic to detect the last devloss timeout of remote nodes which
was still in use of FCF. At that point, the driver should set the last
in-use remote node devloss timeout flag if it was not already set and should
perform proper action on the in-use FCF and recover of FCF from firmware,
depending on the state the driver's FIP engine is in.
Find eligible FCF through FCF table rescan or the next new FCF event when
FCF table rescan turned out empty eligible FCF, and the successful flogi
into an FCF shall clear the HBA_DEVLOSS_TMO flag, indicating the successful
recovery from devloss timeout.
[jejb: add delay.h include to lpfc_hbadisc.c to fix ppc compile]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace graceful teardown steps with the singular function reset command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FCoE Related Fixes
- Correct find-next-FCF routine so that it searches at next FCF rather
than current one.
- Enhanced round-robin FCF failover algorithm to re-start on "New FCF"
async event
- Update the manner in which we look at FCFs while they may be in
their discovery state.
- Use LPFC_FCOE_NULL_VID macro when checkinf for valid vlan_id for FCF
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fixed accounting of allocated SCSI buffers when post sgl fails.
- Restrict scsi buffer allocation based on LUN count (sdev_cnt).
- Create __lpfc_sli_free_rpi that doesn't take out the hbalock.
- Modify lpfc_sli_free_rpi to call __lpfc_sli_free_rpi.
- Call __lpfc_sli_free_rpi in lpfc_cleanup_pending_mbox.
- Do not swap the strings returned in mailbox commands and do
not swap byte aligned data in VPD.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Prevent unregistring of unused FCF when FLOGI is pending.
- Prevent point to point discovery on a FCoE HBA.
- Fixed FCF discovery failure after swapping FCoE port by
switching over to fast failover method when no FCF matches in-use FCF.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Allow enabling MSI-X intterupts with fewer vectors than requested
by looking at the return value from pci_enable_msix.
- Implemented driver PCI AER error handling routines for supporting
AER error recovering on SLI4 devices.
- Remove redundant SLI_ACTIVE checks
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Change the Max receive size on CIN FCFs to 0x800
- (From linux community) Check boundary before checking for NULL.
- Update last completion time for completed I/O to prevent heartbeat.
- Add Balius PCI Device IDs
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add the new Logical Link speed event support.
- Add RATOV and EDTOV to the REG_VFI mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FCF failover improvements
- Add random FCF failover when there are multiple FCFs available.
- Prevent FCF log messages from being displayed for FC adapters.
- Separate the New FCF and Modified FCF log messages.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Added round robin FCF failover on initial or FCF rediscovery FLOGI failure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Prevent Vport discovery after reg_new_vport completes when physical
logged in using FDISC.
- Remove fast FCF failover fabric name matching. Allow failover to FCFs
connected to different fabrics.
- Added fast FCF failover in response to FCF DEAD event on current
FCF record.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Clear LPFC_DRIVER_ABORTED on FCP command completion.
- Clear exchange busy flag when I/O is aborted and found on aborted list.
- Free sglq when XRI_ABORTED event is processed before release of IOCB.
- Only process iocb as aborted when LPFC_DRIVER_ABORTED is set.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add support for the INTF (Interface) PCI register.
- Add support for greater than 2 page SGLs.
- Add support for up to 32 bit BDE lengths.
- Implement the Port Capabilities Mailbox command.
- Stop checking the Minor Code in the EQE structure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Display Logical Link Speed when supported and is non-zero.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix hardware/SLI relates issues:
- Fix CNA uses more than one EQ when in INTx interrupt mode.
- Fix driver tries to process failed read FCF record mailbox request.
- Fix allocating single receive buffer breaks FCoE receive queue.
- Support new read FCF record mailbox error case.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hardware related Fixes and Changes.
- Added new Adapter IDs and update default Adapter names.
- Added PCI read after EQarm doorbell PCI write to flush the write
and avoid spurrious interrupts when in INTx mode.
- Phase out use of ONLINE registers.
- Fix for lost MSI interrupt
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC protocol fixes.
- Fix send sequence logic to handle multi SGL IOCBs.
- Fix FDISC completion always setting VPORT state to failed.
- Ported the fix on reporting of max_vpi to uppper layer.
- Fix incorrect number of Vports allowed to be created.
- Fixed Dead FCoE port after creating vports.
- Added handling of ELS request for Reinstate Recovery Qualifier (RRQ)
- Handle unsolicited CT exchange initiator receiving CT exchange ABTS
- Migrate LUN queue depth ramp up code to scsi mid-layer.
- Made ABTS WQE go to the same WQ as the WQE to be aborted.
- Fix Vport does not rediscover after FCF goes away.
- Fixed lpfc_unreg_vfi failure after devloss timeout.
- Fixed RPI bit leak.
- Fix hbq pointer corruption during target discovery.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following changes:
- Fixed Panic/Hang when using polling mode for fcp commands
- Added support for Read_rev mbox bits indicating FIP mode of HBA
- Optimize performance of slow-path handling of els responses
- Add code to cleanup orphaned unsolicited receive sequences
- Fixed Devloss timeout when multiple initiators are in same zone
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch include the following fixes and changes:
- Fix crash when "error" is echoed to board_mode sysfs parameter
- Fix FCoE Parameter parsing in regions 23
- Fix driver crash when creating vport with large number of targets on SLI4
- Fix bug with npiv message being logged when it is not supported by the adapter
- Fix a potential dereferencing mailbox structure after free bug
- Fix firmware crash after vport create with high target count
- Error out requests to set board_mode to warm restart via sysfs on SLI4 HBAs
- Fix Block guard logging
- Fix a memory corruption issue during GID_FT IO prep
- Fix crash while processing unsolicited FC frames
- Fix failed to allocate XRI message is not a critical failure
- Update and fix formatting in some log messages
- Fix missing new line characters in log messages
- Removed the use of the locally defined FC transport layer related macros
- Check the rsplen in lpfc_handle_fcp_err function before using rsplen
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following fixes and new features:
- Fix mask size for CT field in WQE
- Fix VPI base not used when unregistering VPI on port 1.
- Fix UNREG_VPI mailbox command to unreg the correct VPI
- Fixed Check for aborted els command
- Fix error when trying to load driver with wrong firmware on FCoE HBA.
- Fix bug with probe_one routines not putting the Scsi_Host back upon error
- Add support for Clear Virtual Link Async Events
- Add support for unsolicited CT exchange sequence abort
- Add 0x0714 OCeXXXXX PCI ID
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following fixes:
- Fixed panic during HBA reset.
- Fixed FCoE event tag passed in resume_rpi.
- Fix out of order ELS commands
- Fixed discovery issues found during VLAN testing.
- Fix UNREG_VPI failure on extended link pull
- Fixed crash while processing unsolicited FC frames.
- Clear retry count in the delayed ELS handler
- Fixed discovery failure during quick link bounce.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Consistently implement persistent port disable.
Ability was to be managed in the adapter via firmware via flash settings.
However, not all firmware images supported it. Uniformly support it
everywhere.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Various SLI4 fixes
- Fix switch name not used in the FCF record for FCoE HBAs
- Enabled HBA UE error polling error-condition action code
- Rewrite lpfc_sli4_scmd_to_wqidx_distr() to handle counter rollover cleanly
- Modify resume_rpi mailbox data structure to match current SLI4 spec
- Do not issue mailbox command in MBX_POLL mode when LPFC_HBA_ERROR is set
- Wait for HBA POST completion before checking Online and UE registers
- Fix accumulated total length not being filled in on unsolicited IOCBs
- Use PCI config space register to determine SLI rev of HBA
- Turn on starting ELS tmo function timer during device initialization
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Contains the following changes
- Set the CT field of FDISC to 3
- Fixed over allocation of SCSI buffers on SLI4
- Removed unused jump table entries
- Increase LPFC_WQE_DEF_COUNT to 256
- Updated FDISC context to VPI
- Fixed immediate SCSI command for LUN reset translation to WQE
- Extended mailbox handling to allow MBX_POLL commands in between async
MBQ commands
- Fixed SID used for FDISC
- Fix crash when accessing ctlregs from sysfs for SLI4 HBAs
- Fix SLI4 firmware version not being saved or displayed correctly
- Expand CQID field in WQE structure to 16 bits
- Fix post header template mailbox command timing out
- Removed FCoE PCI device ID 0x0705
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Smart