R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
for this SoC. Public users only have ES2 onwards.
In addition to the ES1 specific removals, a check for it was added
preventing the machine to boot further. It may otherwise inherit wrong
clock settings from ES2 which could damage the hardware.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230202092332.2504-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
"sydm" is a bit name. Let's rename it to the common "sys-dmac".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87v8l3z3y8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
"sydm" is a bit name. Let's rename it to the common "sys-dmac".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87tu0nz3xr.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently the PLLs are modeled as fixed factor clocks, based on initial
settings. However, enabling CPU boost clock rates requires increasing
the PLL clock rates.
Add a custom clock driver to model the PLL clocks on R-Car Gen4, and use
it for PLL2 on R-Car V4H. This allows the Z clock (Cortex-A76 core
clock) to request PLL rate changes, and enable boost mode for the High
Performance mode. For now this is limited to integer multiplication
modes.
Note that the definition for CPG_PLLxCR0_NI uses the value for R-Car V4H.
On R-Car S4-8, the integer and fractional multiplication fields are one
bit larger resp. smaller, but R-Car S4-8 does not support High
Performance mode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/76a5952900a6e15604c640bc8a27762e0e936677.1670492384.git.geert+renesas@glider.be
The CFG_USB[H2MODE] allows to switch the USB configuration. The
configuration supported are:
- One host and one device
or
- Two hosts
Set CFG_USB[H2MODE] based on the USBF controller (USB device)
availability.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-3-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If cpg_mssr_common_init() fails after assigning priv to global variable
cpg_mssr_priv, it deallocates priv, but cpg_mssr_priv keeps dangling
pointer that potentially can be used later.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f7db7bbf0 ("clk: renesas: cpg-mssr: Add early clock support")
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1671806417-32623-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add CRU clock and reset entries to CPG driver.
CRU_SYSCLK and CRU_VCLK clocks need to be turned ON/OFF in particular
sequence for the CRU block hence add these clocks to
r9a07g044_no_pm_mod_clks[] array and pass it as part of CPG data for
both RZ/G2L and RZ/V2L SoCs.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221221212703.348278-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add Compare-Match Timer (TIM) clock and reset entries to CPG
driver.
The TIM IP on the RZ/V2M comes with 32 channels, but the ISP has
full control of channels 0 to 7, and channels 24 to 31. Therefore
Linux is only allowed to use channels 8 to 23.
The TIM has shared peripheral clock with other modules, so mark it
as critical clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221205145955.391526-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clocks related to display which are needed to get the DSI output
working.
Extracted from Renesas BSP tree.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221201095631.89448-4-tomi.valkeinen+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the table in Note 5 for the OSC clock in Table 8.1.4e
("Lists of CPG clocks generated from PLL5") of the R-Car V4H Series
Hardware User's Manual Rev. 0.54, the predividers for the OSC clock are
16 resp. 32 when using a 16.66 resp. 33.33 MHz external crystal.
Fixes: 0ab55cf183 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/dcd572acc584c237f70d2309e038f25040236a87.1669740722.git.geert+renesas@glider.be
Add PWM{8..14} clock and reset entries to CPG driver.
The PWM IP on the RZ/V2M comes with 16 channels, but the ISP has
full control of channels 0 to 7, and channel 15, therefore Linux
is only allowed to use channels 8 to 14.
The PWM channel 15 shares apb clock and reset with PWM{8..14}.
The reset is deasserted by the bootloader/ISP.
Add PWM{8..14} clocks to CPG driver and mark apb clock as
critical clock, so that the apb clock will be always on.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221124191643.3193423-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RSwitch2 and EtherTSN-IF clocks were accidentally mixed up.
While at it, rename them to better match the (future) documentation.
Fixes: a3b4137a4d ("clk: renesas: r8a779f0: Add Ethernet Switch clocks")
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/99b8b41bd2c5043c9e457862ef4bc144869eca58.1668501212.git.geert+renesas@glider.be
As serial communication requires a clean clock signal, the Serial
Communication Interfaces with FIFO (SCIF) are clocked by a clock that is
not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the SCIF modules from the S0D12_PER
clock to the SASYNCPERD4 clock (which has the same clock rate), cfr.
R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 24aaff6a6c ("clk: renesas: cpg-mssr: Add support for R-Car S4-8")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) are clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 080bcd8d59 ("clk: renesas: r8a779f0: Add HSCIF clocks")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If condition (clkspec.np != pd->dev.of_node) is true, then the driver
ends up in an endless loop, forever, locking up the machine.
Fixes: aad03a66f9 ("clk: renesas: r9a06g032: Add clock domain support")
Reviewed-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Gareth Williams <gareth.williams.jx@renesas.com>
Link: https://lore.kernel.org/r/20221028113834.7496-1-marex@denx.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are cases where not all CPG_MOD clocks should be assumed to support
PM. For example on the CRU block there is a particular sequence that needs
to be followed to initialize the CSI-2 D-PHY in which individual clocks
need to be turned ON/OFF, due to which Runtime PM support wasn't used by
the CRU CSI-2 driver.
This patch adds support to allow indicating if PM is not supported by the
CPG_MOD clocks. Two new members no_pm_mod_clks and num_no_pm_mod_clks are
added to struct rzg2l_cpg_info so that MOD clocks which do not support PM
can be passed by no_pm_mod_clks[] array and when the driver uses Runtime
PM support the clk ID is matched against the no_pm_mod_clks[] array to see
if the clk is needed to be included as part of Runtime PM.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026014227.162121-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix typo pll5_mux_dsi_div_params -> mux_dsi_div_params
Fixes the below warning (make W=1):
drivers/clk/renesas/rzg2l-cpg.c:115: warning: Function parameter or member 'mux_dsi_div_params' not described in 'rzg2l_cpg_priv'
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026012123.159790-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the module clock used by the SPI Multi I/O Bus Controller (RPC-IF)
on the Renesas R-Car V4H (R8A779G0) SoC.
While at it, fix table alignment in the definition of the related
RPCSRC internal clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f0609c82e742865be753b67a0a6080f193f405ad.1665583328.git.geert+renesas@glider.be
Add the SASYNCPER internal clock, which is the clock source of the
various SASYNCPERD[124] clocks, to match the clock tree diagram in the
documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/18e6765bfc3bf7c3ee5ce93a370d377c1d17728e.1665558014.git.geert+renesas@glider.be
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231253.15592-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231013.14791-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCY1kNmwAKCRCKwlD9ZEnx
cHGMAP90gnxw9QtkoODnLu2MbcdNNoB/AFeY4O6snbGcwJTYEQD9GqBXxZ3rhZtR
t34KBpENqFdv5HByIxKQ0OT+yYRZew0=
=oXTL
-----END PGP SIGNATURE-----
Merge tag 'renesas-clk-fixes-for-v6.1-tag1'
clk: renesas: Fixes for v6.1
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) is clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car V4H Hardware User's Manual rev. 0.54.
Fixes: 0ab55cf183 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/b7928abc8b9f53d5b06ec8624342f449de3d24ec.1665147497.git.geert+renesas@glider.be
On R-Car V4H, all PLLs except PLL5 support Spread Spectrum and/or
Fractional Multiplication to reduce electromagnetic interference.
Add the SASYNCPER and SASYNCPERD[124] clocks, which are used as clock
sources for modules that must not be affected by Spread Spectrum and/or
Fractional Multiplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/d0f35c35e1f96c5a649ab477e7ba5d8025957cd0.1665147497.git.geert+renesas@glider.be
Currently, determine_rate() is not doing any round operation
and due to this it always selects a lower clock source compared
to the closest higher one.
Support sd clk mux round operation by passing
CLK_MUX_ROUND_CLOSEST flag to clk_mux_determine_rate_flags().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220919084110.3065156-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang