- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at probe
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl/XAWAQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW40rIB/sG1foD0j1iImcTfjlVW4I21HabniykUPBw
GTUlsHoDEEjhY3jEjdYx+l8HHdcqadmedR27DO91l+2ieR7uVoIn2lTADbxnWrgl
DsE6aQLf7KWn340UxEUtihNaa14Zr45GcpYdqs0tjMClRHxM0udwd6qIFHGCi9AC
MOA6kFJewLdCqIRYwBoo1VD4iYQA0RMR463KLvIdrS1bGpkaB3ihxBZb3QgR2ILD
mG9sZClCzeivjNkuiCrJrkWZgAvYTM5DZugBd9+X85Qtq4921zQS5QfZLA9UjnFh
7ChrsTJQFz6CByt6oAH4jCtc0T1hJRL9o1FlbIsAO6gP5mRxKFUV
=bIwk
-----END PGP SIGNATURE-----
mergetag object ee4e0eafa4
type commit
tag nand/for-5.11
tagger Miquel Raynal <miquel.raynal@bootlin.com> 1608042580 +0100
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* AU1550: Ensure the presence of the right includes
* Davinci: Do not use extra dereferencing
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
Others:
* onenand: Use mtd->oops_panic_write as condition
* plat-ram: correctly free memory on error path in platram_probe()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl/Yz80ACgkQJWrqGEe9
VoTGxAf8CqJ1nc3kuhHasjyIQ+cCK6TkqP3KciGXOlmLJXFkhvk9ge/9Q0qttevh
gA/y5wQWn4L7o5nssslKNZ9UXCv7Ksopukx8gFjXHXM0CeukJ7Px3Phlu27WLiOn
qgmSX3xTVV8wdcVXxS+iNpsu3v5G/H4rZLb2V0bH8+tvalAEje8k6AHP4XLLrjIS
mcjkhLn46ttT7WvxmVmlUN+ghrmFRT5DnhgaD7JdE9beaJv8yZ8MLoz5oFD56Z9S
f7qYugVW0ClOK/YvuPRRCiJcMg3siHxm8XtqQTA2spq/LY6hBEykNFlxbQ/23DXa
1kCUi2L1ld+JOe9YgK+OskoIf+Fywg==
=mqSb
-----END PGP SIGNATURE-----
Merge tags 'spi-nor/for-5.11' and 'nand/for-5.11' into mtd/next
SPI NOR core changes:
- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at probe
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* AU1550: Ensure the presence of the right includes
* Davinci: Do not use extra dereferencing
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
Others:
* onenand: Use mtd->oops_panic_write as condition
* plat-ram: correctly free memory on error path in platram_probe()
Traditionally, Linux unlocks the whole flash because there are legacy
devices which has the write protection bits set by default at startup.
If you actually want to use the flash protection bits, eg. because there
is a read-only part for a bootloader, this automatic unlocking is
harmful. If there is no hardware write protection in place (usually
called WP#), a startup of the kernel just discards this protection.
I've gone through the datasheets of all the flashes (except the Intel
ones where I could not find any datasheet nor reference) which supports
the unlocking feature and looked how the sector protection was
implemented. The currently supported flashes can be divided into the
following two categories:
(1) block protection bits are non-volatile. Thus they keep their values
at reset and power-cycle
(2) flashes where these bits are volatile. After reset or power-cycle,
the whole memory array is protected.
(a) some devices needs a special "Global Unprotect" command, eg.
the Atmel AT25DF041A.
(b) some devices require to clear the BPn bits in the status
register.
Due to the reasons above, we do not want to clear the bits for flashes
which belong to category (1). Fortunately for us, only Atmel flashes
fall into category (2a). Implement the "Global Protect" and "Global
Unprotect" commands for these. For (2b) we can use normal block
protection locking scheme.
This patch adds a new flag to indicate the case (2). Only if we have
such a flash we unlock the whole flash array. To be backwards compatible
it also introduces a kernel configuration option which restores the
complete legacy behavior ("Disable write protection on any flashes").
Hopefully, this will clean up "unlock the entire flash for legacy
devices" once and for all.
For reference here are the actually commits which introduced the legacy
behavior (and extended the behavior to other chip manufacturers):
commit f80e521c91 ("mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips")
commit ea60658a08 ("mtd: m25p80: disable SST software protection bits by default")
commit 7228982442 ("[MTD] m25p80: fix bug - ATmel spi flash fails to be copied to")
Actually, this might also fix handling of the Atmel AT25DF flashes,
because the original commit 7228982442 ("[MTD] m25p80: fix bug -
ATmel spi flash fails to be copied to") was writing a 0 to the status
register, which is a "Global Unprotect". This might not be the case in
the current code which only handles the block protection bits BP2, BP1
and BP0. Thus, it depends on the current contents of the status register
if this unlock actually corresponds to a "Global Unprotect" command. In
the worst case, the current code might leave the AT25DF flashes in a
write protected state.
The commit 191f5c2ed4 ("mtd: spi-nor: use 16-bit WRR command when QE
is set on spansion flashes") changed that behavior by just clearing BP2
to BP0 instead of writing a 0 to the status register.
Further, the commit 3e0930f109 ("mtd: spi-nor: Rework the disabling
of block write protection") expanded the unlock_all() feature to ANY
flash which supports locking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-8-michael@walle.cc
These flashes have some weird BP bits mapping which aren't supported in
the current locking code. Just add a simple unlock op to unprotect the
entire flash array which is needed for legacy behavior.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-7-michael@walle.cc
For the Atmel and SST parts this flag was already moved to individual
flash parts because it is considered bad esp. because newer flash chips
will automatically inherit the "has locking" support. While this won't
likely be the case for the Intel parts, we do it for consistency
reasons.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-6-michael@walle.cc
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all SST parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes
which supports BP locking. In particular the following flashes
don't support the BP scheme:
- SST26VF016B
- SST26WF016B
- SST26VF064B
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-5-michael@walle.cc
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all Atmel parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes which
supports BP locking. In particular the following flashes don't support
the BP scheme:
- AT26F004
- AT25SL321
- AT45DB081D
Please note, that some flashes which are marked as SPI_NOR_HAS_LOCK just
support Global Protection, i.e. not our supported block protection
locking scheme. This is to keep backwards compatibility with the
current "unlock all at boot" mechanism. In particular the following
flashes doesn't have BP bits:
- AT25DF041A
- AT25DF321
- AT25DF321A
- AT25DF641
- AT26DF081A
- AT26DF161A
- AT26DF321
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-4-michael@walle.cc
Just try to unlock the whole SPI-NOR flash array. Don't abort the
probing in case of an error. Justifications:
(1) For some boards, this just works because
spi_nor_write_16bit_sr_and_check() is broken and just checks the
second half of the 16bit. Once that will be fixed, SPI probe will
fail for boards which has hardware-write protected SPI-NOR flashes.
(2) Until now, hardware write-protection was the only viable solution
to use the block protection bits. This is because this very
function spi_nor_unlock_all() will be called unconditionally on
every linux boot. Therefore, this bits only makes sense in
combination with the hardware write-protection. If we would fail
the SPI probe on an error in spi_nor_unlock_all() we'd break
virtually all users of the block protection bits.
(3) We should try hard to keep the MTD working even if the flash might
not be writable/erasable.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-3-michael@walle.cc
This flash part actually has 4 block protection bits.
Please note, that this patch is just based on information of the
datasheet of the datasheet and wasn't tested.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Reported-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-2-michael@walle.cc
The S28 flash family uses 2-bit ECC by default with each ECC block being
16 bytes. Under this scheme multi-pass programming to an ECC block is
not allowed. Set the writesize to make sure multi-pass programming is
not attempted on the flash.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-4-p.yadav@ti.com
Some flashes like the Cypress S28 family use ECC. Under this ECC scheme,
multi-pass writes to an ECC block is not allowed. In other words, once
data is programmed to an ECC block, it can't be programmed again without
erasing it first.
Upper layers like file systems need to be given this information so they
do not cause error conditions on the flash by attempting multi-pass
programming. This can be done by setting 'writesize' in 'struct
mtd_info'.
Set the default to 1 but allow flashes to modify it in fixup hooks. If
more flashes show up with this constraint in the future it might be
worth it to add it to 'struct flash_info', but for now increasing its
size is not worth it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-3-p.yadav@ti.com
There are a few typos in comments in the SPI NOR framework; fix them.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201130152416.1283972-1-j.neuschaefer@gmx.net
Fixes the following W=1 kernel build warning(s):
drivers/mtd/spi-nor/controllers/hisi-sfc.c:328: warning: Function parameter or member 'np' not described in 'hisi_spi_nor_register'
drivers/mtd/spi-nor/controllers/hisi-sfc.c:328: warning: Function parameter or member 'host' not described in 'hisi_spi_nor_register'
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-8-lee.jones@linaro.org
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.
The flash supports the soft reset sequence. So, add the flag in the
flash's info.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-16-p.yadav@ti.com
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. But the sector map
table on the part I had was programmed incorrectly and the SMPT values
on the flash don't match the public datasheet. Specifically, in some
places erase type 3 was used instead of 4. In addition, the region sizes
were incorrect in some places. So, for testing I set CFR3N[3] to enable
uniform sector sizes. Since the uniform sector mode bit is a
non-volatile bit, this series does not change it to avoid making any
permanent changes to the flash configuration. The correct data to
implement a fixup is not available right now and will be done in a
follow-up patch if needed.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[vigneshr@ti.com: Drop unnecessary sleep in Octal DTR switch sequence]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-15-p.yadav@ti.com
On resume, the init procedure will be run that will re-enable it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-14-p.yadav@ti.com
Perform a Soft Reset on shutdown on flashes that support it so that the
flash can be reset to its initial state and any configurations made by
spi-nor (given that they're only done in volatile registers) will be
reset. This will hand back the flash in pristine state for any further
operations on it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-13-p.yadav@ti.com
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-12-p.yadav@ti.com
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-11-p.yadav@ti.com
Parse just the 22nd dword and look for the 'DTR Octal Mode Enable
Volatile bit'.
SPI_NOR_IO_MODE_EN_VOLATILE should be set just for the flashes
that don't define the optional SFDP SCCR Map. For the others,
let the SFDP do its job and fill the SNOR_F_IO_MODE_EN_VOLATILE
flag. We avoid this way polluting the flash flags when declaring
one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201005153138.6437-10-p.yadav@ti.com
We don't want to enter a stateful mode, where a X-X-X I/O mode
is entered by setting a non-volatile bit, because in case of a
reset or a crash, once in the non-volatile mode, we may not be able
to recover in bootloaders and we may break the SPI NOR boot.
Forbid by default the I/O modes that are set via a non-volatile bit.
SPI_NOR_IO_MODE_EN_VOLATILE should be set just for the flashes that
don't define the optional SFDP SCCR Map, so that we don't pollute the
flash info flags.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201005153138.6437-9-p.yadav@ti.com
Some controllers, like the cadence qspi controller, have trouble reading
only 1 byte in DTR mode. So, do 2 byte reads for SR and FSR commands in
DTR mode, and then discard the second byte.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-8-p.yadav@ti.com
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in octal DTR mode.
Use that information to send the correct Read SR command.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-7-p.yadav@ti.com
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
dummy cycles, the number of dummy cycles needed for a Read Status
Register command, and the number of address bytes needed for a Read
Status Register command.
We don't know what speed the controller is running at. Find the fast
read dummy cycles for the fastest frequency the flash can run at to be
sure we are never short of dummy cycles. If nothing is available,
default to 20. Flashes that use a different value should update it in
their fixup hooks.
Since we want to set read settings, expose spi_nor_set_read_settings()
in core.h.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-6-p.yadav@ti.com
Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-5-p.yadav@ti.com
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
The xSPI spec says that "The program commands provide SPI backward
compatible commands for programming data...". So 8D-8D-8D page program
opcodes are populated with using 1S-1S-1S opcodes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-4-p.yadav@ti.com
They are thin wrappers around
nor->controller_ops->{read_reg,write_reg,erase}(). In a future commit
DTR support will be added. These ops can not be supported by the
controller_ops hooks and these helpers will make it easier to reject
those calls.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-3-p.yadav@ti.com
ENOTSUPP is not a SUSV4 error code. Using EOPNOTSUPP is preferred
in its stead.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-2-p.yadav@ti.com
If a flash chip has more than 16MB capacity but its BFPT reports
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, the spi-nor framework defaults to 3.
The check in spi_nor_set_addr_width() doesn't catch it because addr_width
did get set. This fixes that check.
Fixes: f9acd7fa80 ("mtd: spi-nor: sfdp: default to addr_width of 3 for configurable widths")
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20201006132346.12652-1-bert@biot.com
This reverts commit 03edda0e1e.
This leads to warn dump like [1] on some platforms and reorders MTD
devices which may break user space expectations [2]. So revert the change.
[1]:
[ 1.849801] ------------[ cut here ]------------
[ 1.854271] mscc_felix 0000:00:00.5: device is disabled, skipping
[ 1.858753] WARNING: CPU: 1 PID: 7 at kernel/kmod.c:136 __request_module+0x3a4/0x568
[...]
[2] Bug report: https://lore.kernel.org/linux-mtd/20201003150633.23416-1-michael@walle.cc/
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201005090321.8724-1-vigneshr@ti.com
Add support Winbond w25q{64,128,256}jwm which are identical to existing
w25q32jwm except for their sizes.
This was tested with w25q64jwm, basic erase/write/readback and
lock/unlock both lower/upper blocks were okay.
Signed-off-by: ikjn@chromium.org <ikjn@chromium.org>
Signed-off-by: Xingyu Wu <wuxy@bitland.corp-partner.google.com>
Signed-off-by: ST Lin <stlin2@winbond.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200928060631.2090541-1-ikjn@chromium.org
Intel Alder Lake-S has the same SPI serial flash controller as Cannon
Lake. Add Alder Lake-S PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200925095109.51148-1-mika.westerberg@linux.intel.com
On my system the spi_nor_probe() took ~6 ms at bootup. That's not a
lot, but every little bit adds up to a slow bootup. While we can get
this out of the boot path by making it a module, there are times where
it is convenient (or even required) for this to be builtin the kernel.
Let's set that we prefer async probe so that we don't block other
drivers from probing while we are probing.
This is a tiny little change that is almost guaranteed to be safe for
anything that is able to run as a module, which SPI_NOR is.
Specifically modules are already probed asynchronously. Also: since
other things in the system may have enabled asynchronous probe the
system may already be doing other things during our probe.
There is a small possibility that some other driver that was a client
of SPI_NOR didn't handle -EPROBE_DEFER and was relying on probe
ordering and only worked when the SPI_NOR and the SPI bus were
builtin. In that case the other driver has a bug that's waiting to
hit and the other driver should be fixed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200902160002.1.I658d1c0db9adfeb9a59bc55e96a19e192c959e55@changeid
As the only user has been removed in previous patch, let's revert
this one together.
This reverts commit be192209d5.
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-2-git-send-email-yangyicong@hisilicon.com
Previous patch intends to restore the flash's QE bit when removed/shutdown,
but may have some problems and break the flash:
- for those originally in Quad mode, this patch will clear the QE bit
when unloaded the flash, which is incorrect.
- even with above problem solved, it may still break the flash as some
flash's QE bit is non-volatile and lots of set/reset will wear out
the bit.
- the restore method cannot be proved to be valid as if a hard
reset or accident crash happened, the spi_nor_restore() won't be
performed the the QE bit will not be restored as we expected to.
So let's revert it to fix this. The discussion can be found at [1].
This reverts commit cc59e6bb6c.
[1] https://lore.kernel.org/linux-mtd/CAO8h3eFLVLRmw7u+rurKsg7=Nh2q-HVq-HgVXig8gf5Dffk8MA@mail.gmail.com/
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-1-git-send-email-yangyicong@hisilicon.com
Both w25q64 and s25fl064k nor flash support QUAD and DUAL read
command, hence update the same in flash_info table.
This is tested on Broadcom Stingray SoC (bcm958742t).
s25fl064k and w25q64 share the same JEDEC ID. The search alg will
return the first hit, so s25fl064k even for the winbond parts. We
should differentiate between these flashes, but it's not in the
scope of this patch. Related discussion at:
Link: https://lore.kernel.org/patchwork/patch/628090/
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200529071655.739-1-rayagonda.kokatanur@broadcom.com
[tudor.ambarus@microchip.com: Update commit message and indicate that
s25fl064k and w25q64 share the same JEDEC ID]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Micron mt25qu02g supports both x2 and x4 transactions. Add the
SPI_NOR_DUAL_READ flag to its spi_nor_ids[] table entry.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-3-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Macronix mx66u2g45g is a 1.8V, 2Gbit (256MB) device that
supports x1, x2, or x4 operation.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-2-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
After spi_nor_write_disable() return code checks were introduced in the
spi-nor front end intel-spi backend stopped to work because WRDI was never
supported and always failed.
Just pretend it was sucessful and ignore the command itself. HW sequencer
shall do the right thing automatically, while with SW sequencer we cannot
do it anyway, because the only tool we had was preopcode and it makes no
sense for WRDI.
Fixes: bce679e5ae ("mtd: spi-nor: Check for errors after each Register Operation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/282e1305-fd08-e446-1a22-eb4dff78cfb4@nokia.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
If the flash's quad mode is enabled, it'll remain in the quad mode when
it's removed. If we drive the flash next time in Standard/Dual SPI mode,
the QE bit is not cleared and the function of flash's WP# and RESET#/HOLD#
have been switched to IO2 and IO3 and are not restored.
Disable the Quad mode in spi_nor_restore(), then the flash's QE bit will
be cleared when removed. This will make sure the flash always enter the
Standard/Dual SPI mode when loaded.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-3-git-send-email-yangyicong@hisilicon.com
Previous we didn't provide a way to disable the flash's quad mode.
Which means we cannot do some cleanup works when to remove or
poweroff the flash, like what set 4-byte address mode does in
spi_nor_restore().
Add the capability to disable the flash quad mode, by introducing
an enable flag in the flash parameters quad_enable() hooks and
related functions.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-2-git-send-email-yangyicong@hisilicon.com
The s70fl01gs is a dual die stack of two s25fl512s die with dedicated chip
select pins to each. Tested with the device and confirmed that is working
as two s25fl512s devices. The current device ID in the flash_info table
matches with s70fs01gs which does not work with current MTD (s70fs01gs
does not support RDSR(05h) which is critical for erase/write).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200626051650.495-1-Takahiro.Kuwano@cypress.com
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing and let flashes set it in
their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-12-p.yadav@ti.com
This chip is (nearly) identical to the Winbond w25q64 which is
already supported by Linux. Compared to the w25q64, the 'jvm'
has a different JEDEC ID.
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
[tudor.ambarus@microchip.com: Order entry alphabetically, update
subject, update Sven's email address]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200629195306.1030-1-TheSven73@gmail.com
The MX25R1635F is the smaller sibling of the MX25R3235F that is
already supported. It's only half the size (16Mb).
It was tested on the Kontron Electronics i.MX8MM SoM (N8010)
using raw read and write from and to the mtd device and
the 'flash_erase' command.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[tudor.ambarus@microchip.com: update subject]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200702140523.6811-1-frieder.schrempf@kontron.de
Intel Tiger Lake-H has the same SPI serial flash controller as Cannon
Lake. Add Tiger Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200624192103.78770-1-mika.westerberg@linux.intel.com
Intel Emmitsburg has the same SPI serial flash controller as Lewisburg.
Add Emmitsburg PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200615155748.920-1-mika.westerberg@linux.intel.com
Now that cadence-quadspi has been converted to use spi-mem framework,
move it under drivers/spi/
Update license header to match SPI subsystem style
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-9-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Miquel Raynal