Without timeout reports, it is impossible to decode many protocols since
it is not known when the transmission ends. timeout reports are sent by
default, but can be turned off. There is no reason to turn them off, and
I cannot find any software which does this, so we can safely remove it.
This makes the ioctl LIRC_SET_REC_TIMEOUT_REPORTS a no-op.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The beginning part of the "existing HSV/HSL formats" table (line 7742)
reads:
.. raw:: latex
\begingroup
\tiny
\setlength{\tabcolsep}{2pt}
However, the ending part (line 7834) reads:
.. raw:: latex
\normalsize
Fix the imbalance by replacing the \normalsize with \endgroup.
Note:
Actually, the imbalance is harmless and just results in an
informative message near the bottom of userspace-api.log:
(\end occurred inside a group at level 1)
### semi simple group (level 1) entered at line 70696 (\begingroup)
### bottom level
Link: https://lore.kernel.org/linux-media/b3eeec4d-1a34-0a1a-3097-1ddea3b5f1c8@gmail.com
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
V4L2_PIX_FMT_HM12 was redefined to V4L2_PIX_FMT_NV12_16L16, so use the
new name in libv4l-introduction.rst.
This fixes this warning:
libv4l-introduction.rst:27: WARNING: undefined label: v4l2-pix-fmt-hm12
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAPTURE buffers might be read by the hardware after they are dequeued,
which goes against the general idea that userspace has full control over
dequeued buffers. Explain why and document the restrictions that this
implies for userspace.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the VP9 stateless decoder controls plus the documentation that goes
with it.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Co-developed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Co-developed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Improve the documentation for CEC_RECEIVE/TRANSMIT w.r.t. the
sequence and tx/rx_status fields.
Also remove a duplicate tx_status description.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix example code which has missing or double backslash typo.
Signed-off-by: Kwang Son <dev.kwang.son@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2_COLORFX_SET_RGB color effects control, V4L2_CID_COLORFX_RGB
for RGB color setting.
with two mirror changes:
- change 0xFFFFFF to 0xffffff
- fix comments 2^24 to 2^24 - 1
[hverkuil: dropped spaces around + with V4L2_CID_BASE for consistency]
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch lets user-space request a non-coherent memory
allocation during CREATE_BUFS and REQBUFS ioctl calls.
= CREATE_BUFS
struct v4l2_create_buffers has seven 4-byte reserved areas,
so reserved[0] is renamed to ->flags. The struct, thus, now
has six reserved 4-byte regions.
= CREATE_BUFS32
struct v4l2_create_buffers32 has seven 4-byte reserved areas,
so reserved[0] is renamed to ->flags. The struct, thus, now
has six reserved 4-byte regions.
= REQBUFS
We use one byte of a 4 byte ->reserved[1] member of struct
v4l2_requestbuffers. The struct, thus, now has reserved 3 bytes.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
By setting or clearing the V4L2_MEMORY_FLAG_NON_COHERENT flag
user-space should be able to hint vb2 that either non-coherent
(if supported) or coherent memory should be used for the buffer
allocation.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The uvc driver relies on the camera firmware to keep the control states
and therefore is not capable of changing an inactive control.
Allow returning -EACCES in those cases.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add documentation for the V4L2_CID_NOTIFY_GAINS control.
This control is required by sensors that need to know what colour
gains will be applied to pixels by downstream processing (such as by
an ISP), though the sensor does not apply these gains itself.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add Mediatek's non-compressed 8 bit block video mode. This format is
produced by the MT8183 codec and can be converted to a non-proprietary
format by the MDP3 component.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add more information about V4L2_PIX_FMT_NV12MT and
V4L2_PIX_FMT_NV12M_16X16, so it's clearer for driver authors and users.
Also, group the two pixel formats with the other tiled formats,
for clarity.
Unlike the recently introduced tiled formats (V4L2_PIX_FMT_NV12_4L4, etc)
these formats have remained Samsung-specific until now. Therefore, and
although the NV12MT and NV12MT_16X16 nomenclatures are less clear, we are
keeping them as-is.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This format is produced by VeriSilicon Hantro G2 and VC8000D cores.
It is a simple 4x4 tiling layout in a linear way.
The pixel format was introduced by GStreamer using FourCC VT12,
so let's stick to it.
Link: https://gstreamer.freedesktop.org/documentation/video/video-format.html
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_PIX_FMT_HM12 format is actually a simple NV12 tiled format,
with 16x16 linear tiles. Rename the format and move its documentation
together with the other tiled NV12 formats.
Keep V4L2_PIX_FMT_HM12 for application compatibility.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_PIX_FMT_SUNXI_TILED_NV12 format is actually a fairly
common NV12 tiled format, with 32x32 linear tiles. Rename the format
and move its documentation together with the other tiled NV12 formats.
Keep V4L2_PIX_FMT_SUNXI_TILED_NV12 for application compatibility.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
HEVC scaling lists are used for the scaling process for transform
coefficients.
V4L2_HEVC_SPS_FLAG_SCALING_LIST_ENABLED has to set when they are
encoded in the bitstream.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a control to set intra-refresh period.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In all drivers _CYCLIC_INTRA_REFRESH_MB default control value is zero
which means that the macroblocks will not be intra-refreshed. Document
this _CYCLIC_INTRA_REFRESH_MB control behaviour in control description.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Improve the documentation of the frame rate configuration so that it can
be understood by a regular human being.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_CID_PIXEL_RATE is nowadays used to tell pixel sampling rate in
the sub-device's pixel array, not the pixel rate over a link (for which it
also becomes unfit with the addition of multiplexed streams later on). Fix
this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix kerneldoc syntax in v4l2-async. The references were not produced
correctly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Modernise the documentation to make it more precise and update the use of
pixel rate control and various other changes. In particular:
- Use non-proportional font for file names, properties as well as
controls.
- The unit of the HBLANK control is pixels, not lines.
- The unit of PIXEL_RATE control is pixels per second, not Hz.
- Merge common requirements for CSI-2 and parallel busses.
- Include all DT properties needed for assigned clocks.
- Fix referencing the link rate control.
- SMIA driver's new name is CCS driver.
- The PIXEL_RATE control denotes pixel rate on the pixel array on camera
sensors. Do not suggest it is used to tell the maximum pixel rate on the
bus anymore.
- Improve ReST syntax (plain struct and function names).
- Remove the suggestion to use s_power() in receiver drivers.
- Make MIPI website URL use HTTPS, add Wikipedia links to BT.601 and
BT.656.
Fixes: e4cf8c58af ("media: Documentation: media: Document how to write camera sensor drivers")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If HEVC frame consists of multiple slices, segment address has to be
known in order to properly decode it.
Add segment address field to slice parameters.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix typo in a define: CEC_OP_REC_SEQ_SATERDAY -> CEC_OP_REC_SEQ_SATURDAY
This isn't used yet in actual applications to the best of my knowledge,
and it certainly doesn't break the ABI since the value doesn't change.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The :doc:`foo` tag is auto-generated via automarkup.py.
So, use the filename at the sources, instead of :doc:`foo`.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The :doc:`foo` tag is auto-generated via automarkup.py.
So, use the filename at the sources, instead of :doc:`foo`.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HEVC HANTRO driver needs to know the number of bits to skip at
the beginning of the slice header.
That is a hardware specific requirement so create a dedicated control
for this purpose.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add decode params control and the associated structure to group
all the information that are needed to decode a reference frame as
is described in ITU-T Rec. H.265 section "8.3.2 Decoding process
for reference picture set".
Adapt Cedrus driver to these changes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add fields and flags as they are defined in
7.4.3.3.1 "General picture parameter set RBSP semantics of the
H.265 ITU specification.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
sps_max_sub_layers_minus1 is needed if the driver wishes to determine
whether or not a frame might be used for reference.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only upstream driver using the API described there is the
av7110 driver.
As the driver was moved to staging, move the API bits to staging
as well.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST
conversion and some cut-and-pasted text contain some characters that
aren't easily reachable on standard keyboards and/or could cause
troubles when parsed by the documentation build system.
Replace the occurences of the following characters:
- U+00a0 (' '): NO-BREAK SPACE
as it can cause lines being truncated on PDF output
- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK
- U+201c ('“'): LEFT DOUBLE QUOTATION MARK
- U+201d ('”'): RIGHT DOUBLE QUOTATION MARK
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST
conversion and some cut-and-pasted text contain some characters that
aren't easily reachable on standard keyboards and/or could cause
troubles when parsed by the documentation build system.
Replace the occurences of the following characters:
- U+00a0 (' '): NO-BREAK SPACE
as it can cause lines being truncated on PDF output
- U+2014 ('—'): EM DASH
- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK
Note that Sphinx auto-translates '---' into EM DASH.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST
conversion and some cut-and-pasted text contain some characters that
aren't easily reachable on standard keyboards and/or could cause
troubles when parsed by the documentation build system.
Replace the occurences of the following characters:
- U+201c ('“'): LEFT DOUBLE QUOTATION MARK
- U+201d ('”'): RIGHT DOUBLE QUOTATION MARK
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The header defines the user space interface but may be mistaken as
kernel-only header due to its location. Add "uapi" directory under
driver's include directory and move the header there.
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2-ctrls.c source has become much too big, so split it up
into four separate parts:
v4l2-ctrls-core.c: contains the core framework code
v4l2-ctrls-api.c: contains the uAPI interface to the framework
v4l2-ctrls-defs.c: contains the control definitions
v4l2-ctrls-request.c: contains the Request API helpers
And it adds a new v4l2-ctrls-priv.h.
No code was changed, but a number of checkpatch.pl warnings were
fixed (alignment, f == NULL -> !f, long comment block coding style,
unsigned -> unsigned int).
The copyright statements were updated as well since they were
quite out of date.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Until now, the MPEG-2 V4L2 API was not exported as a public API,
and only defined in a private media header (media/mpeg2-ctrls.h).
After reviewing the MPEG-2 specification in detail, and reworking
the controls so they match the MPEG-2 semantics properly,
we can consider it ready.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Hantro and Cedrus drivers work in frame-mode,
meaning they expect all the slices in a picture (either frame
or field structure) to be passed in each OUTPUT buffer.
These two are the only V4L2 MPEG-2 stateless decoders currently
supported. Given the VA-API drivers also work per-frame,
coalescing all the MPEG-2 slices in a buffer before the decoding
operation, it makes sense to not expect slice-mode drivers and
therefore remove V4L2_CID_MPEG_VIDEO_MPEG2_SLICE_PARAMS.
This is done to avoid carrying an unused interface. If needed,
this control can be added without breaking backwards compatibility.
Note that this would mean introducing a enumerator control to
specify the decoding mode (see V4L2_CID_STATELESS_H264_DECODE_MODE).
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The forward and backwards references are specified per-picture
and not per-slice. Move it to V4L2_CID_MPEG_VIDEO_MPEG2_PICTURE.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Typically, bitstreams are composed of a sequence header,
followed by a number of picture header and picture coding extension
headers. Each picture can be composed of a number of slices.
Let's split the MPEG-2 uAPI to follow these semantics more closely,
allowing more usage flexibility. Having these controls split up
allows applications to set a sequence control at the beginning
of a sequence, and then set a picture control for each frame.
While here add padding fields where needed, and document
the uAPI header thoroughly.
Note that the V4L2_CTRL_TYPE_{} defines had to be moved because
it clashes with existing ones. This is not really an issue
since they will be re-defined when the controls are moved
out of staging.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Our current MPEG-2 uAPI uses 1-byte fields for MPEG-2
boolean syntax elements. Clean these by adding a 'flags'
field and flag macro for each boolean syntax element.
A follow-up change will refactor this uAPI so we don't need
to add padding fields just yet.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As stated in the MPEG-2 specification, section 6.3.7 "Quant matrix
extension":
Each quantisation matrix has a default set of values. When a
sequence_header_code is decoded all matrices shall be reset to
their default values. User defined matrices may be downloaded
and this can occur in a sequence_header() or in a
quant_matrix_extension().
The load_intra_quantiser_matrix syntax elements are transmitted
in the bitstream headers, signalling that a quantisation matrix
needs to be loaded and used for pictures transmitted afterwards
(until the matrices are reset).
This "load" semantics are implemented in the V4L2 interface
without the need of any "load" flags: passing the control
is effectively a load.
Therefore, rework the V4L2_CID_MPEG_VIDEO_MPEG2_QUANTISATION
semantics to match the MPEG-2 semantics. Quantisation matrices
values are now initialized by the V4L2 control core to their
reset default value, and applications are expected to reset
their values as specified.
The quantisation control is therefore optional, and used to
load bitstream-defined values in the quantisation matrices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MPEG-2 specification refers to the quantisation matrices
using the word "quantisation". Make the V4L2 interface more
ergonomic by matching the MPEG-2 spec.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dependent slice segment flag for PPS control is misnamed. It should have
"enabled" at the end. It only tells if this flag is present in slice
header or not and not the actual value.
Fix this by renaming the PPS flag and introduce another flag for slice
control which tells actual value.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The rx-arb-lost error injection command only works with <op> set to 'any'.
Explicitly say so in the usage message.
Also use [] to indicate that the <poll> argument is optional.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sean Young