This change makes it so that the GRE and VXLAN tunnels can make use of Tx
checksum offload support provided by some drivers via the hw_enc_features.
Without this fix enabling GSO means sacrificing Tx checksum offload and
this actually leads to a performance regression as shown below:
Utilization
Send
Throughput local GSO
10^6bits/s % S state
6276.51 8.39 enabled
7123.52 8.42 disabled
To resolve this it was necessary to address two items. First
netif_skb_features needed to be updated so that it would correctly handle
the Trans Ether Bridging protocol without impacting the need to check for
Q-in-Q tagging. To do this it was necessary to update harmonize_features
so that it used skb_network_protocol instead of just using the outer
protocol.
Second it was necessary to update the GRE and UDP tunnel segmentation
offloads so that they would reset the encapsulation bit and inner header
offsets after the offload was complete.
As a result of this change I have seen the following results on a interface
with Tx checksum enabled for encapsulated frames:
Utilization
Send
Throughput local GSO
10^6bits/s % S state
7123.52 8.42 disabled
8321.75 5.43 enabled
v2: Instead of replacing refrence to skb->protocol with
skb_network_protocol just replace the protocol reference in
harmonize_features to allow for double VLAN tag checks.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ndo_ll_poll to ndo_busy_poll.
Rename sk_mark_ll to sk_mark_napi_id.
Rename skb_mark_ll to skb_mark_napi_id.
Correct all useres of these functions.
Update comments and defines in include/net/busy_poll.h
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the file and correct all the places where it is included.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit ba418fa357 ("soreuseport: UDP/IPv4 implementation")
added following sparse errors :
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:433:60: warning: incorrect type in argument 1 (different base types)
net/ipv4/udp.c:433:60: expected unsigned short [unsigned] [usertype] val
net/ipv4/udp.c:433:60: got restricted __be16 [usertype] sport
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: incorrect type in argument 1 (different base types)
net/ipv4/udp.c:514:60: expected unsigned short [unsigned] [usertype] val
net/ipv4/udp.c:514:60: got restricted __be16 [usertype] sport
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to TCP offloading and UDPv6 offloading, move all related
UDPv4 functions to udp_offload.c to make things more explicit. Also,
by this, we can make those functions static.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add upport for busy-polling on UDP sockets.
In __udp[46]_lib_rcv add a call to sk_mark_ll() to copy the napi_id
from the skb into the sk.
This is done at the earliest possible moment, right after we identify
which socket this skb is for.
In __skb_recv_datagram When there is no data and the user
tries to read we busy poll.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current state of affairs is that read()/write() will setup
RFS (Receive Flow Steering) for internet protocol sockets while
poll()/epoll() does not.
When poll() gets called with a TCP or UDP socket, we should update
the flow target.
This permits to RFS (if enabled) to select the appropriate CPU for
following incoming packets.
Note: Only connected UDP sockets can benefit from RFS.
Signed-off-by: David Majnemer <majnemer@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Turner <pjt@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.
The aim of this code is to provide GSO in software for MPLS packets
whose skbs are GSO.
SKB Usage:
When an implementation adds an MPLS stack to a non-MPLS packet it should do
the following to skb metadata:
* Set skb->inner_protocol to the old non-MPLS ethertype of the packet.
skb->inner_protocol is added by this patch.
* Set skb->protocol to the new MPLS ethertype of the packet.
* Set skb->network_header to correspond to the
end of the L3 header, including the MPLS label stack.
I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to
kernel" which adds MPLS support to the kernel datapath of Open vSwtich.
That patch sets the above requirements in datapath/actions.c:push_mpls()
and was used to exercise this code. The datapath patch is against the Open
vSwtich tree but it is intended that it be added to the Open vSwtich code
present in the mainline Linux kernel at some point.
Features:
I believe that the approach that I have taken is at least partially
consistent with the handling of other protocols. Jesse, I understand that
you have some ideas here. I am more than happy to change my implementation.
This patch adds dev->mpls_features which may be used by devices
to advertise features supported for MPLS packets.
A new NETIF_F_MPLS_GSO feature is added for devices which support
hardware MPLS GSO offload. Currently no devices support this
and MPLS GSO always falls back to software.
Alternate Implementation:
One possible alternate implementation is to teach netif_skb_features()
and skb_network_protocol() about MPLS, in a similar way to their
understanding of VLANs. I believe this would avoid the need
for net/mpls/mpls_gso.c and in particular the calls to
__skb_push() and __skb_push() in mpls_gso_segment().
I have decided on the implementation in this patch as it should
not introduce any overhead in the case where mpls_gso is not compiled
into the kernel or inserted as a module.
MPLS GSO suggested by Jesse Gross.
Based in part on "v4 GRE: Add TCP segmentation offload for GRE"
by Pravin B Shelar.
Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than having logic to calculate inner protocol in every
tunnel gso handler move it to gso code. This simplifies code.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set correct skb->protocol so that inner packet can
lookup correct gso handler.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Add MIB counters for checksum errors in IP layer,
and TCP/UDP/ICMP layers, to help diagnose problems.
$ nstat -a | grep Csum
IcmpInCsumErrors 72 0.0
TcpInCsumErrors 382 0.0
UdpInCsumErrors 463221 0.0
Icmp6InCsumErrors 75 0.0
Udp6InCsumErrors 173442 0.0
IpExtInCsumErrors 10884 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, sock_tx_timestamp() always returns 0. The comment that
describes the sock_tx_timestamp() function wrongly says that it
returns an error when an invalid argument is passed (from commit
20d4947353, ``net: socket infrastructure for SO_TIMESTAMPING'').
Make the function void, so that we can also remove all the unneeded
if conditions that check for such a _non-existant_ error case in the
output path.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This reverts commit d6a8c36dd6.
Next commit makes this commit unnecessary.
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to GRE tunnel, UDP tunnel should take care of IP header ID
too.
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users of udp encapsulation currently have an encap_rcv callback which they can
use to hook into the udp receive path.
In situations where a encapsulation user allocates resources associated with a
udp encap socket, it may be convenient to be able to also hook the proto
.destroy operation. For example, if an encap user holds a reference to the
udp socket, the destroy hook might be used to relinquish this reference.
This patch adds a socket destroy hook into udp, which is set and enabled
in the same way as the existing encap_rcv hook.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds generic tunneling offloading support for IPv4-UDP based
tunnels.
GSO type is added to request this offload for a skb.
netdev feature NETIF_F_UDP_TUNNEL is added for hardware offloaded
udp-tunnel support. Currently no device supports this feature,
software offload is used.
This can be used by tunneling protocols like VXLAN.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_net_remove is only used to remove proc entries
that under /proc/net,it's not a general function for
removing proc entries of netns. if we want to remove
some proc entries which under /proc/net/stat/, we still
need to call remove_proc_entry.
this patch use remove_proc_entry to replace proc_net_remove.
we can remove proc_net_remove after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds GRE protocol offload handler so that
skb_gso_segment() can segment GRE packets.
SKB GSO CB is added to keep track of total header length so that
skb_segment can push entire header. e.g. in case of GRE, skb_segment
need to push inner and outer headers to every segment.
New NETIF_F_GRE_GSO feature is added for devices which support HW
GRE TSO offload. Currently none of devices support it therefore GRE GSO
always fall backs to software GSO.
[ Compute pkt_len before ip_local_out() invocation. -DaveM ]
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow multiple UDP sockets to bind to the same port.
Motivation soreuseport would be something like a DNS server. An
alternative would be to recv on the same socket from multiple threads.
As in the case of TCP, the load across these threads tends to be
disproportionate and we also see a lot of contection on the socketlock.
Note that SO_REUSEADDR already allows multiple UDP sockets to bind to
the same port, however there is no provision to prevent hijacking and
nothing to distribute packets across all the sockets sharing the same
bound port. This patch does not change the semantics of SO_REUSEADDR,
but provides usable functionality of it for unicast.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a socket release callback function to check
if the socket cached route got invalid during the time
we owned the socket. The function is used from udp, raw
and ping sockets.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
In UDP recvmsg(), we miss an increase of UDP_MIB_INERRORS if the copy
of skb to userspace failed for whatever reason.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_send_skb() can send orphaned skb, so we must pass the net pointer to
avoid possible NULL dereference in error path.
Bug added by commit 3a7c384ffd (ipv4: tcp: unicast_sock should not
land outside of TCP stack)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dropwatch wrongly diagnose all received UDP packets as drops.
This patch removes trace_kfree_skb() done in skb_free_datagram_locked().
Locations calling skb_free_datagram_locked() should do it on their own.
As a result, drops are accounted on the right function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ip_rt_frag_needed() removed, we have to explicitly update PMTU
information in every ICMP error handler.
Create two helper functions to facilitate this.
1) ipv4_sk_update_pmtu()
This updates the PMTU when we have a socket context to
work with.
2) ipv4_update_pmtu()
Raw version, used when no socket context is available. For this
interface, we essentially just pass in explicit arguments for
the flow identity information we would have extracted from the
socket.
And you'll notice that ipv4_sk_update_pmtu() is simply implemented
in terms of ipv4_update_pmtu()
Note that __ip_route_output_key() is used, rather than something like
ip_route_output_flow() or ip_route_output_key(). This is because we
absolutely do not want to end up with a route that does IPSEC
encapsulation and the like. Instead, we only want the route that
would get us to the node described by the outermost IP header.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP stack needs a minimum hash size value for proper operation and also
uses alloc_large_system_hash() for proper NUMA distribution of its hash
tables and automatic sizing depending on available system memory.
On some low memory situations, udp_table_init() must ignore the
alloc_large_system_hash() result and reallocs a bigger memory area.
As we cannot easily free old hash table, we leak it and kmemleak can
issue a warning.
This patch adds a low limit parameter to alloc_large_system_hash() to
solve this problem.
We then specify UDP_HTABLE_SIZE_MIN for UDP/UDPLite hash table
allocation.
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace simple_strtoul with kstrtoul in three similar occurrences, all setup
handlers:
* route.c: set_rhash_entries
* tcp.c: set_thash_entries
* udp.c: set_uhash_entries
Also check if the conversion failed.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_add_backlog() & sk_rcvqueues_full() hard coded sk_rcvbuf as the
memory limit. We need to make this limit a parameter for TCP use.
No functional change expected in this patch, all callers still using the
old sk_rcvbuf limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch errors of the following type:
* ERROR: "foo * bar" should be "foo *bar"
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most machines dont use UDP encapsulation (L2TP)
Adds a static_key so that udp_queue_rcv_skb() doesnt have to perform a
test if L2TP never setup the encap_rcv on a socket.
Idea of this patch came after Simon Horman proposal to add a hook on TCP
as well.
If static_key is not yet enabled, the fast path does a single JMP .
When static_key is enabled, JMP destination is patched to reach the real
encap_type/encap_rcv logic, possibly adding cache misses.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: dev@openvswitch.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Add #define pr_fmt(fmt) as appropriate.
Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".
Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.
Add missing "\n" to pr_info in gre.c.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one is only considered for MSG_PEEK flag and the value pointed by
it specifies where to start peeking bytes from. If the offset happens to
point into the middle of the returned skb, the offset within this skb is
put back to this very argument.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP_UNICAST_IF feature is needed by the Wine project. This patch
implements the feature by setting the outgoing interface in a similar
fashion to that of IP_MULTICAST_IF. A separate option is needed to
handle this feature since the existing options do not provide all of
the characteristics required by IP_UNICAST_IF, a summary is provided
below.
SO_BINDTODEVICE:
* SO_BINDTODEVICE requires administrative privileges, IP_UNICAST_IF
does not. From reading some old mailing list articles my
understanding is that SO_BINDTODEVICE requires administrative
privileges because it can override the administrator's routing
settings.
* The SO_BINDTODEVICE option restricts both outbound and inbound
traffic, IP_UNICAST_IF only impacts outbound traffic.
IP_PKTINFO:
* Since IP_PKTINFO and IP_UNICAST_IF are independent options,
implementing IP_UNICAST_IF with IP_PKTINFO will likely break some
applications.
* Implementing IP_UNICAST_IF on top of IP_PKTINFO significantly
complicates the Wine codebase and reduces the socket performance
(doing this requires a lot of extra communication between the
"server" and "user" layers).
bind():
* bind() does not work on broadcast packets, IP_UNICAST_IF is
specifically intended to work with broadcast packets.
* Like SO_BINDTODEVICE, bind() restricts both outbound and inbound
traffic.
Signed-off-by: Erich E. Hoover <ehoover@mines.edu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP diag get_exact handler will require them to find a
socket by provided net, [sd]addr-s, [sd]ports and device.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 81d54ec847.
If we take the "try_again" goto, due to a checksum error,
the 'len' has already been truncated. So we won't compute
the same values as the original code did.
Reported-by: paul bilke <fsmail@conspiracy.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le lundi 07 novembre 2011 à 15:33 +0100, Eric Dumazet a écrit :
> At least, in recent kernels we dont change dst->refcnt in forwarding
> patch (usinf NOREF skb->dst)
>
> One particular point is the atomic_inc(dst->refcnt) we have to perform
> when queuing an UDP packet if socket asked PKTINFO stuff (for example a
> typical DNS server has to setup this option)
>
> I have one patch somewhere that stores the information in skb->cb[] and
> avoid the atomic_{inc|dec}(dst->refcnt).
>
OK I found it, I did some extra tests and believe its ready.
[PATCH net-next] ipv4: IP_PKTINFO doesnt need dst reference
When a socket uses IP_PKTINFO notifications, we currently force a dst
reference for each received skb. Reader has to access dst to get needed
information (rt_iif & rt_spec_dst) and must release dst reference.
We also forced a dst reference if skb was put in socket backlog, even
without IP_PKTINFO handling. This happens under stress/load.
We can instead store the needed information in skb->cb[], so that only
softirq handler really access dst, improving cache hit ratios.
This removes two atomic operations per packet, and false sharing as
well.
On a benchmark using a mono threaded receiver (doing only recvmsg()
calls), I can reach 720.000 pps instead of 570.000 pps.
IP_PKTINFO is typically used by DNS servers, and any multihomed aware
UDP application.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_queue_rcv_skb() has a possible race in encap_rcv handling, since
this pointer can be changed anytime.
We should use ACCESS_ONCE() to close the race.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the tcp and udp code creates a set of struct file_operations at runtime
while it can also be done at compile time, with the added benefit of then
having these file operations be const.
the trickiest part was to get the "THIS_MODULE" reference right; the naive
method of declaring a struct in the place of registration would not work
for this reason.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck