'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.
This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.
This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.
The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.
I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.
v3 - Brown paper bag its too early in the morning actually run
git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: Mantesh Sarashetti <mantesh@ti.com>
Tested-by: Mantesh Sarashetti <mantesh@ti.com>
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There could be possible race condition where the host dev's
are alloced and added to platform dev just before usbhs_init.
Just move usbhs_init before adding child dev.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the hardcoded magic values for dma mask and use the dma
mask api/macro available.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
Use gpio_request_one() instead of multiple gpiolib calls.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The usbhs core driver does not enable/disable the interface and
functional clocks directly, These clocks are handled by runtime pm,
hence instead of the clock enable/disable, the runtime pm APIS are
used. however,the optional clocks and port clocks are handled by
the usbhs core.
Dependency:
This patch is dependent on this series:
[PATCH 0/5 v13 or latest version] omap: usb: host: Runtime PM preparation
for EHCI and OHCI drivers.
Validation performed:
The global suspend/resume of EHCI and OHCI is validated on
OMAP3430 sdp board with this patch combined with the series:
[PATCH 0/5 v13 or latest version] omap: usb: host: Runtime PM preparation
for EHCI and OHCI drivers.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
device name usbhs clocks are changed from
usbhs-omap.0 to usbhs_omap; this is because
in the hwmod registration the device name is set
as usbhs_omap; The redudant clock nodes are removed.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The patch fixes the build failure:
drivers/mfd/omap-usb-host.c:1034:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1034:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL_GPL'
drivers/mfd/omap-usb-host.c:1034:1: warning: parameter names (without
types) in function declaration
drivers/mfd/omap-usb-host.c:1040:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1040:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL_GPL'
drivers/mfd/omap-usb-host.c:1040:1: warning: parameter names (without
types) in function declaration
drivers/mfd/omap-usb-host.c:1045:13: error: 'THIS_MODULE' undeclared
here (not in a function)
drivers/mfd/omap-usb-host.c:1050:15: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1050:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1050:1: warning: type defaults to 'int' in
declaration of 'MODULE_AUTHOR'
drivers/mfd/omap-usb-host.c:1050:15: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1051:14: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1051:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1051:1: warning: type defaults to 'int' in
declaration of 'MODULE_ALIAS'
drivers/mfd/omap-usb-host.c:1051:14: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1052:16: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1052:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1052:1: warning: type defaults to 'int' in
declaration of 'MODULE_LICENSE'
drivers/mfd/omap-usb-host.c:1052:16: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1053:20: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1053:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1053:1: warning: type defaults to 'int' in
declaration of 'MODULE_DESCRIPTION'
drivers/mfd/omap-usb-host.c:1053:20: warning: function declaration isn't
a prototype
make[2]: *** [drivers/mfd/omap-usb-host.o] Error 1
CC fs/proc/namespaces.o
make[1]: *** [drivers/mfd] Error 2
make: *** [drivers] Error 2
make: *** Waiting for unfinished jobs....
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This code section seems to have been accidentally copy pasted.
It causes incorrect bits to be set up in the TLL_CHANNEL_CONF
register and prevents the TLL mode from working correctly.
Cc: stable@kernel.org
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
usbhs_disable function was invoking clk_enable() instead of
clk_disable(), thus only increasing the clock usage counter and
preventing this particular clock from being ever turned off.
Because of this, the power domain of omap4 the USB Host subsystem
would never reach lower power states.This patch calls clk_disable()
in usbhs_disable function
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This reverts commit 7e6502d577.
Oops are produced during initialization of ehci and ohci
drivers. This is because the run time pm apis are used by
the driver but the corresponding hwmod structures and
initialization is not merged. hence revering back the
commit id 7e6502d577
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reported-by: Luciano Coelho <coelho@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The usbhs core driver does not enable/disable the interface and
functional clocks; These clocks are handled by hwmod and runtime pm,
hence insted of the clock enable/disable, the runtime pm APIS are
used. however,the port clocks and tll clocks are handled
by the usbhs core.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1. Return proper error if omap_usbhs_alloc_child fails
2. In the case of goto err_ehci, we should call platform_device_unregister(ehci)
instead of platform_device_put(ehci) because we have already added the
platform device to device hierarchy.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The disabling of clocks and freeing GPIO are changed
to fix the occurrence of the crash of rmmod of ehci and ohci
drivers. The GPIOs should be freed after the spin locks are
unlocked.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With commit 19403165 a main part of ehci-omap.c moved to
drivers/mfd/omap-usb-host.c created by commit 17cdd29d.
Due to this reorganisation the polarity used to reset the
external USB phy changed and USB host doesn't recognize
any devices.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
in case of ehci phy mode; regulator of phy
should be enabled before initializing the
usbhs core driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Steve Calfee <stevecalfee@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the case of missing platform_data we do not hold a spin_lock,
thus we should not call spin_unlock_irqrestore in the error path.
Also simplify the error handling by separating the successful path
from error path. I think this change improves readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Steve Calfee <stevecalfee@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
enabling and disabling the common clocks for ehci
and ohci is implemented. usbhs is a common parent
platform driver for EHCI and OHCI driver. This driver
receives the clock enable and disable requests
from ehci and ohci drivers.The UHH and TLL
initialization is also performed.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Russ Dill