There is no need to announce that the driver has been successfully
probed, so remove the unneeded message.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of returning -EINVAL on error, return the real error code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'np' variable is already assigned to 'pdev->dev.of_node', so use
it to improve readability.
No functional change.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i.MX51 datasheet says:
Chapter 56.1.2.4 I2S Mode
...
When I2S modes are entered (I2S master (01) or I2S slave (10)),
the following settings are recommended:
...
- TX Frame Rate should be 2 i.e. (STCCR[12:8] = 1)
- RX Frame Rate should be 2 i.e. (SRCCR[12:8] = 1)
Chapter 56.3.3.12 SSI Transmit and Receive Clock Control Registers (STCCR & SRCCR)
...
Bits 12-8 DC4-DC0
Frame Rate Divider Control. These bits are used to control the divide ratio
for the programmable frame rate dividers. The divide ratio works on the word
clock. In Normal mode, this ratio determines the word transfer rate.
In Network mode, this ratio sets the number of words per frame. The divide
ratio ranges from 1 to 32 in Normal mode and from 2 to 32 in Network mode.
In Normal mode, a divide ratio of 1 (DC=00000) provides continuous periodic
data word transfer. A bit-length frame sync must be used in this case.
Function fsl_ssi_hw_params() setup Normal mode for MONO output,
so with DC=0, SSI enters to continuous periodic data word transfer.
To fix this, setup DC for any I2S mode.
Patch has tested on custom board based on Digi CCMX-51 module (i.MX51).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
m32r allmodconfig build is failing with the error:
ERROR: "bad_dma_ops" [sound/soc/fsl/snd-soc-fsl-asrc.ko] undefined!
The code is using DMA but the related dependency is not mentioned in the
Kconfig.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Happened when the Playback (or Capture) is running continuously
and Capture (or Playback) is restarted (xrun, manual stop/start...)
Since the RX (or TX) FIFO are only reset when the whole SSI is disabled,
pending samples from previous capture (or playback) session may still
be present. They must be erased to not introduce channel slipping.
FIFO Clear register fields are documented in IMX51, IMX35 reference manual.
They are not documented in IMX50 or IMX6 RM, despite they are
working as expected on IMX6SL and IMX6solo.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, SCR.SSIEN and SCR.TE were enabled at once if no capture
stream was also running.
This may not give a chance for the DMA to write the first sample in
TX FIFO before the streaming starts on the PCM bus, inserting void
samples first.
Those void samples are then responsible for slipping the channels.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the capture is already running while playback is started, it is highly
probable (>80% in a 8 channels scenario) that samples are lost between
the DMA and TX fifo.
The reason is that SIER.TDMAE is set before STCR.TFEN0, leaving a time
window where the FIFO doesn't receive the samples written by the DMA.
This particular case happened only if capture is already enabled as
SCR.SSIEN is already set at the playback startup instant.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of functions only receive the ssi_private reference and don't have
a knowledge of 'dev' pointer, even for debug purpose.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
im6sl reference manual 47.7.4:
"
Bit clock - Used to serially clock the data bits in and out of the SSI port.
This clock is either generated internally (from SSI's sys clock) or taken
from external clock source (through the Tx/Rx clock ports).
[...]
Care should be taken to ensure that the bit clock frequency (either
internally generated by dividing the SSI's sys clock or sourced from
external device through Tx/Rx clock ports) is never greater than 1/5
of the ipg_clk (from CCM) frequency.
"
Since, in master mode, the sysclk is a multiple of bitclk, we can
easily reach a high sysclk value, whereas keeping a reasonable bitclk.
ex: 8ch x 16bit x 48kHz = 6144000, requires a 24576000 sysclk (PM=1)
yet ipg_clk/5 = 66Mhz/5 = 13.2
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max number of slots in TDM mode is 32:
- Frame Rate Divider Control is a 5bit value
- Time slot mask registers control 32 slots.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On mx6ul the General Purpose Register 1 (GPR1) contains the following
bits for configuring the direction of the SAI MCLKs:
SAI1_MCLK_DIR, SAI2_MCLK_DIR, SAI3_MCLK_DIR
Introduce the "fsl,sai-mclk-direction-output" optional property to allow
configuring the SAI_MCLK outputs.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MX6UL may need to configure the General Purpose Register 1 (GPR1), so
it is better to add a new compatible string to differentiate.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CCSR_SSI_SOR is a register that clears the TX and/or the RX fifo
on the i.MX SSI port. The fsl_ssi_trigger writes this register in
order to clear the fifo at trigger time.
However, since the CCSR_SSI_SOR register is not in the volatile list,
the caching mechanism prevented the register write in the trigger
function. This caused the fifo to not be cleared (because the value
was unchanged from the last time the register was written), and thus
causes the channels in both TDM or simple I2S mode to slip and be in
the wrong time slots on SSI restart.
This has gone unnoticed for so long because with simple stereo mode,
the consequence is that left and right are swapped, which isn't that
noticeable. However, it's catestrophic in some systems that
require the channels to be in the right slots.
Signed-off-by: Caleb Crome <caleb@crome.org>
Suggested-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Documentation/printk-formats.txt has
size_t: use %zu or %zx
runtime->dma_bytes is of type size_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Cc+v
-----END PGP SIGNATURE-----
Merge tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514"
* tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (291 commits)
ALSA: hda - Fix mutex deadlock at HDMI/DP hotplug
ALSA: ctl: change return value in compatibility layer so that it's the same value in core implementation
ALSA: mixart: silence an uninitialized variable warning
ALSA: usb-audio: Add sanity checks for endpoint accesses
ALSA: usb-audio: Minor code cleanup in create_fixed_stream_quirk()
ALSA: usb-audio: Fix NULL dereference in create_fixed_stream_quirk()
ALSA: hda - Limit i915 HDMI binding only for HSW and later
ALSA: hda - Fix unconditional GPIO toggle via automute
ALSA: mixart: silence unitialized variable warnings
ALSA: hda - Fixes double fault in nvhdmi_chmap_cea_alloc_validate_get_type
ALSA: intel8x0: Add clock quirk entry for AD1981B on IBM ThinkPad X41.
ALSA: hda - Add new GPU codec ID 0x10de0082 to snd-hda
ASoC: rsnd: add simplified module explanation
ASoC: hdac_hdmi: Add broxton device ID
ASoC: Intel: Bxtn: Add Broxton PCI ID
ASoC: Intel: Skylake: Move Skylake dsp ops & loader ops
ASoC: Intel: add dmabuffer to common sst_dsp
ASoC: Intel: Skylake: Unstatify skl_dsp_enable_core
ASoC: Intel: Skylake: Fix whitepsace issues
ASoC: Intel: Skylake: Move module id defines
...
Pull dma_*_writecombine rename from Ingo Molnar:
"Rename dma_*_writecombine() to dma_*_wc()
This is a tree-wide API rename, to move the dma_*() write-combining
APIs closer in name to their usual API families. (The old API names
are kept as compatibility wrappers to not introduce extra breakage.)
The patch was Coccinelle generated"
* 'mm-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dma, mm/pat: Rename dma_*_writecombine() to dma_*_wc()
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is no guarantee that on fsl_ssi module load
SSI registers will have their power-on-reset values.
In fact, if the driver is reloaded the values in
registers will be whatever they were set to previously.
However, the cache needs to be fully populated at probe
time to avoid non-atomic allocations during register
access.
Special case here is imx21-class SSI, since
according to datasheet it don't have SACC{ST,EN,DIS}
regs.
This fixes hard lockup on fsl_ssi module reload,
at least in AC'97 mode.
Fixes: 05cf237972 ("ASoC: fsl_ssi: Add driver suspend and resume to support MEGA Fast")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5c408fee25 ("ASoC: fsl_ssi: remove explicit register defaults")
causes the driver to fail to probe:
fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW
fsl-ssi-dai 2028000.ssi: Failed to init register map
fsl-ssi-dai: probe of 2028000.ssi failed with error -22
, so revert this commit.
Reported-by: Mika Penttilä <mika.penttila@nextfour.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add cs4271 and cs42727 support for fsl-asoc-card
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a pair of warnings when ASRC is absent in the DTB:
fsl-asoc-card sound: ASoC: no source widget found for ASRC-Playback
fsl-asoc-card sound: ASoC: Failed to add route ASRC-Playback -> direct -> CPU-Playback
fsl-asoc-card sound: ASoC: no sink widget found for ASRC-Capture
fsl-asoc-card sound: ASoC: Failed to add route CPU-Capture -> direct -> ASRC-Capture
This is because the driver is still trying to add DAPM routes for ASRC
even if it doesn't exist on that platform.
The warnings are harmless but it might be annoying. So this patch drops
the DAPM routes of ASRC when it's absent in the DAI link.
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When registering a ASoC card the driver data of the parent device is set to
point to the card. This driver data is used in the
snd_soc_suspend()/resume() callbacks.
The imx-spdif driver overwrites the driver data with custom data which
causes snd_soc_suspend() to crash. Since the custom driver is not used
anywhere simply deleting the line which sets the custom driver data fixes
the issue.
Fixes: 43ac946922 ("ASoC: imx-spdif: add snd_soc_pm_ops for spdif machine driver")
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no guarantee that on fsl_ssi module load
SSI registers will have their power-on-reset values.
In fact, if the driver is reloaded the values in
registers will be whatever they were set to previously.
However, the cache needs to be fully populated at probe
time to avoid non-atomic allocations during register
access.
Special case here is imx21-class SSI, since
according to datasheet it don't have SACC{ST,EN,DIS}
regs.
This fixes hard lockup on fsl_ssi module reload,
at least in AC'97 mode.
Fixes: 05cf237972 ("ASoC: fsl_ssi: Add driver suspend and resume to support MEGA Fast")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since msleep() will sleep longer than intended time for values less
than 20ms, this patch allows the use of usleep_range for just 1ms.
usleep_range is a finer precision implementation of msleep and is
designed to be a drop-in replacement for udelay where a precise
sleep/busy-wait is unnecessary.
More details see Documentation/timers/timers-howto.txt.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since msleep() will sleep longer than intended time for values less
than 20ms, this patch allows the use of usleep_range for just 1ms.
usleep_range is a finer precision implementation of msleep and is
designed to be a drop-in replacement for udelay where a precise
sleep/busy-wait is unnecessary.
More details see Documentation/timers/timers-howto.txt.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark some registers precious since their
reads have side effects (like clearing flags).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SACNT register should be marked volatile since
its WR and RD bits are cleared by SSI after
completing the relevant operation.
This unbreaks AC'97 register access.
Fixes: 05cf237972 ("ASoC: fsl_ssi: Add driver suspend and resume to support MEGA Fast")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register ASRCFG is volatile, but some bits need to be recovered
after suspend/resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_ssi uses different stream names ("AC97 Playback" / "AC97 Capture")
in AC'97 mode so in this case fsl-asoc-card route map should
also be using them.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 8kHz, 11.025kHz, 16kHz, 22.05kHz output sample rate support.
According referance menual, "Limited support for the case when
output sampling rates is between 8kHz and 30kHz. The limitation
is the supported ratio (Fsin/Fsout) range as between 1/24 to 8."
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
* x = devm_kzalloc(...);
... when != x == NULL
*x
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After several open/close sai test with ctrl+c, there will be
I/O error. The SAI can't work anymore, can't recover. There
will be no frame clock. With adding the software reset in
trigger stop, the issue can be fixed.
This is a hardware bug/errata and reset is the only option.
According to the reference manual, the software reset doesn't
reset any control register but only internal hardware logics
such as bit clock generator, status flags, and FIFO pointers.
(Our purpose is just to reset the clock generator while the
software reset is the only way to do that.)
Since slave mode doesn't use the clock generator, only apply
the reset procedure to the master mode.
For asynchronous mode, TX will not be reset when RX is still
running. In this case, i can't reproduce this issue.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We get a warning for the imx-pcm-fiq driver when CONFIG_LPAE
is enabled on ARM, because dma_addr_t is 64-bit then:
sound/soc/fsl/imx-pcm-fiq.c: In function 'snd_imx_pcm_mmap':
sound/soc/fsl/imx-pcm-fiq.c:223:107: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the printk to use the correct format string for
printing a dma_addr_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASRC need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to ASRC registers
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPDIF need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to SPDIF registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ESAI need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to ESAI registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
using params_width function to simplify code.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add tdm slots operation support. If tdm slots and slot width have
been configured in machine driver, we should use these values.
Otherwise, using relevant channels and word length to set slots
and slot width.
SAI will generate BCLK depends on sample rate, slots and slot width.
And there may be unused BCLK cycles before each LRCLK transition.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A new randconfig build failure shows that the fsl-asoc-card module
must not be built-in when the AC97 driver is a loadable module:
sound/built-in.o: In function `fsl_asoc_card_late_probe':
:(.text+0x571d8): undefined reference to `snd_ac97_update_bits'
I couldn't come up with a nice solution, so this adds another dependency
on "X || !X", which is the Kconfig way of saying that we have an
optional dependency on something that might be a loadable module.
Fixes: 50760cad9d ("ASoC: fsl-asoc-card: add AC'97 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound card rtd was an array and was updated to a list so update
the driver to use a list
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vendor drivers no longer access a DAI link's runtime by the link index
but by matching the link name via snd_soc_get_pcm_runtime(). We assume
each DAI link has a unique name.
This is preparation for changing runtimes from an array to a list later.
Vendor drivers changed:
sound/soc/fsl/fsl-asoc-card.c
sound/soc/fsl/imx-wm8962.c
sound/soc/pxa/mioa701_wm9713.c
sound/soc/samsung/bells.c
sound/soc/samsung/littlemill.c
sound/soc/samsung/odroidx2_max98090.c
sound/soc/samsung/snow.c
sound/soc/samsung/speyside.c
sound/soc/samsung/tobermory.c
sound/soc/tegra/tegra_wm8903
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For SAI master mode, when Tx(Rx) sync with Rx(Tx) clock, Rx(Tx) will
generate bclk and frame clock for Tx(Rx), we should set RCR4(TCR4),
RCR5(TCR5) and RMR(TMR) for playback(capture), or there will be sync
error sometimes.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In fsl_sai_set_bclk function, we should not set bclk for Tx/Rx Synchronous
with another SAI mode.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
using macro for default register map
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
STL and STR registers are writable and not readable. So they are non volatile.
Remove them from volatile list, and add default register value for them.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
FSL_SAI_TDR register is writable and not readable. According to
regmap_volatile() function, if FSL_SAI_TDR want to be volatile,
it should be readable. So we should remove FSL_SAI_TDR from volatile
register list.
If the flat cache don't have default register map, when do regcache_sync
operation, the non volatile and writable registers will be synchronised
to 0. FSL_SAI_TDR reigster will be written a 0 and cause channel swap.
So add default register map for flat cache, and such register will not
be written.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ETDR and TX0~5 registers are writable and not readable. So they are non
volatile. Remove them from volatile list, and add default register value for
them.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the first batch of updates for sound system on 4.4-rc1.
Again at this time, the update looks fairly calm; no big changes in
either ALSA core or ASoC infrastructures, rather all small cleanups,
in addition to the new stuff as usual.
The biggest changes are about Firewire sound devices. It gained lots
of new device support, and MIDI functionality. Also there are updates
for a few still working-in-progress stuff (topology API and ASoC
skylake), too. But overall, this update should give no big surprise.
Some highlight is below:
Core:
- A few more Kconfig items for tinification; it's marked as EXPERT,
so normal user should't be bothered :)
- Refactoring with a new PCM hw_constraint helper
- Removal of unused transfer_ack_{begin,end} PCM callbacks
Firewire:
- Restructuring of code subtree, lots of refactoring
- Support AMDTP variants
- New driver for Digidesign 002/003 family
- Adds support for TASCAM FireOne to ALSA OXFW driver
- Add MIDI support to TASCAM and Digi00x devices
HD-Audio:
- Automated modalias generation for codec drivers, finally
- Improvement on heuristics for setting mixer name
- A few fixes for longstanding bugs on Creative CA0132 cards
- Addition of audio rate callback with i915 communication
- Fix suspend issue on recent Dell XPS
- Intel Lewisburg controller support
ASoC:
- Updates to the topology userspace interface
- Big updates to the Renesas support (rcar)
- More updates for supporting Intel Sky Lake systems
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825, Rockchip
S/PDIF, and Atmel class D amplifier
USB-Audio:
- A fix for newer Roland MIDI devices
- Quirks and workarounds for Zoom R16/24 device
Misc:
- A few fixes for some old Cirrus CS46xx PCI sound boards
- Yet another fixes for some old ESS Maestro3 PCI sound boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=l9SO
-----END PGP SIGNATURE-----
Merge tag 'sound-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Here is the first batch of updates for sound system on 4.4-rc1.
Again at this time, the update looks fairly calm; no big changes in
either ALSA core or ASoC infrastructures, rather all small cleanups,
in addition to the new stuff as usual.
The biggest changes are about Firewire sound devices. It gained lots
of new device support, and MIDI functionality. Also there are updates
for a few still working-in-progress stuff (topology API and ASoC
skylake), too. But overall, this update should give no big surprise.
Some highlights are below:
Core:
- A few more Kconfig items for tinification; it's marked as EXPERT,
so normal user should't be bothered :)
- Refactoring with a new PCM hw_constraint helper
- Removal of unused transfer_ack_{begin,end} PCM callbacks
Firewire:
- Restructuring of code subtree, lots of refactoring
- Support AMDTP variants
- New driver for Digidesign 002/003 family
- Adds support for TASCAM FireOne to ALSA OXFW driver
- Add MIDI support to TASCAM and Digi00x devices
HD-Audio:
- Automated modalias generation for codec drivers, finally
- Improvement on heuristics for setting mixer name
- A few fixes for longstanding bugs on Creative CA0132 cards
- Addition of audio rate callback with i915 communication
- Fix suspend issue on recent Dell XPS
- Intel Lewisburg controller support
ASoC:
- Updates to the topology userspace interface
- Big updates to the Renesas support (rcar)
- More updates for supporting Intel Sky Lake systems
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825, Rockchip
S/PDIF, and Atmel class D amplifier
USB-Audio:
- A fix for newer Roland MIDI devices
- Quirks and workarounds for Zoom R16/24 device
Misc:
- A few fixes for some old Cirrus CS46xx PCI sound boards
- Yet another fixes for some old ESS Maestro3 PCI sound boards"
* tag 'sound-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (330 commits)
ALSA: hda - Add Intel Lewisburg device IDs Audio
ALSA: hda - Apply pin fixup for HP ProBook 6550b
ALSA: hda - Fix lost 4k BDL boundary workaround
ALSA: maestro3: Fix Allegro mute until master volume/mute is touched
ALSA: maestro3: Enable docking support for Dell Latitude C810
ALSA: firewire-digi00x: add another rawmidi character device for MIDI control ports
ALSA: firewire-digi00x: add MIDI operations for MIDI control port
ALSA: firewire-digi00x: rename identifiers of MIDI operation for physical ports
ALSA: cs46xx: Fix suspend for all channels
ALSA: cs46xx: Fix Duplicate front for CS4294 and CS4298 codecs
ALSA: DocBook: Add soc-ops.c and soc-compress.c
ALSA: hda - Add / fix kernel doc comments
ALSA: Constify ratden/ratnum constraints
ALSA: hda - Disable 64bit address for Creative HDA controllers
ALSA: hda/realtek - Dell XPS one ALC3260 speaker no sound after resume back
ALSA: hda/ca0132 - Convert leftover pr_info() and pr_err()
ASoC: fsl: Use #ifdef instead of #if for CONFIG_PM_SLEEP
ASoC: rt5645: Sort the order for register bit defines
ASoC: dwc: add check for master/slave format
ASoC: rt5645: Add the HWEQ for the speaker output
...
- Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference. from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King
- Disable hugepd for 64K page size. from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file. from Paul Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages. from Christophe Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump
support, a rework of the qoriq clock driver, device tree changes including
qoriq fman nodes, support for a new 85xx board, and some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x
LocalPlus Bus FIFO with its device tree binding documentation, mpc512x
device tree updates and some minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YwcM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
This is a major overhaul of the clk-qoriq driver, which I'm merging
via PPC with Stephen Boyd's ack in order to apply subsequent PPC patches
that depend on it.
When using the Rx clock for both, transmitter and receiver, the
transmitter needs to be set to synchronous with receiver.
This reverts 855675f6e6 ("ASoC: fsl_sai: Set SYNC bit of TCR2 to
Asynchronous Mode"), which, judiging from the commit log, seems to
mixed up between the two synchronous modes: The boolean
sai->synchronous[TX] is indicating wheather the SAI should work in
Rx synchronous mode (sync Tx with Rx), hence if the value is true,
the SYNC field of TCR2 needs to be set to 0x1 ("Synchronous with
receiver").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A first batch of updates targetted at v4.4. There are no substantial
core fixes here, the biggest block of changes is updates to the rcar
drivers and the addition of a CODEC driver for the AK4613.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBF7yAAoJECTWi3JdVIfQ1MEH/jnzSyEVIuG+l8UkMaz6gf4w
zGsM1KCn//mfPl7yAoOdsnElOLR+Fmf+0jx4pCPQKrjvBGwjwH/IwBR1rwuEeUPY
7d66efpWOKlTf3qpsF1S7ZIlAZOs0NFvo0jwA1ZY/pc3YEBekyWxbABk/uWAVrM5
HJJKafI7WeiYrF0l0z2sG7BpsFtr8JKqrOVM+SGaPTNn2k+/lQ1bwTk1liOEUbsv
oq8NFNrUWPBCwbUNJQxBOvmoXC6Oa6+JBVO3+SsoS0q2FweNpqtZopjmoqHM8CiN
SkBeFT+wYlSGSnnFgAXXA2+kq74TeP2CvToo6tw+gf4LZXydKIaAdeuT6M9weZA=
=8h3u
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc2' into asoc-next
ASoC: Updates for v4.4
A first batch of updates targetted at v4.4. There are no substantial
core fixes here, the biggest block of changes is updates to the rcar
drivers and the addition of a CODEC driver for the AK4613.
# gpg: Signature made Fri 25 Sep 2015 05:37:06 KST using RSA key ID 5D5487D0
# gpg: key CD7BEEBC: no public key for trusted key - skipped
# gpg: key CD7BEEBC marked as ultimately trusted
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 16005C11: no public key for trusted key - skipped
# gpg: key 16005C11 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: key 5C6153AD: no public key for trusted key - skipped
# gpg: key 5C6153AD marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Change them to #ifdef as CONFIG_PM_SLEEP might not be defined at all.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rate constraints in this driver are shared between all device
instances. It should not be (and is not) modified at runtime, so make them
const.
While we are at it also change the type of the rates array from u32 to
unsigned int. While both resolve to the same type, u32 is usually used to
empathize that the value is for a 32-bit hardware register or similar which
makes it slightly confusing in this context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add AC'97 support to fsl-asoc-card using generic
ASoC AC'97 CODEC.
The SSI controller will silently enable any TX
AC'97 slots that have their bits set in SLOTREQ
received from CODEC and then will redirect some
of playback samples there.
That's why it is important to make sure that
any of CODEC playback slots that can pull samples
are set to slots 3/4 (standard PCM playback slots).
Currently, this applies to S/PDIF slots as they
were seen to pull samples sometimes even with
S/PDIF output being disabled.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power source of
modules during system suspend and resume procedure. Thus, ESAI needs to save
all the values of registers before the system suspend and restore them after
the system resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power
source of modules during system suspend and resume procedure. Thus,
SSI needs to save all the values of registers before the system
suspend and restore them after the system resume.
The register SFCSR is volatile, but some bits in it need to be
recovered after suspend/resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power source of
modules during system suspend and resume procedure. Thus, SPDIF needs to save
all the values of registers before the system suspend and restore them after
the system resume.
The SRPC register should be volatile, LOCK bit is set by the hardware.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power source of
modules during system suspend and resume procedure. Thus, SAI needs to save
all the values of registers before the system suspend and restore them after
the system resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add snd_soc_pm_ops in machine driver to make the trigger suspend/resume
be called in suspend/resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_DAIFMT_{IB|NB}_{IF|NF} are defined as inverting or not BCLK or
FRM relatively to what is standard for the specified DAI hardware audio
format. Consequently, the absolute polarities of these signals cannot be
derived only from these settings as this driver did. The format has to
be taken into account too.
This fixes inverted left/right channels in I²S mode.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code incorrectly treats dai format for AC97 as bit mask
whereas it's actually an integer value. This causes DAI formats
other than AC97 (e.g. DSP_B) to trigger AC97 related code,
which is incorrect and breaks functionality. This patch fixes
the code to correctly compare values to determine AC97 or not.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-
related changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition
is for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It
was initiated by lockdep warning, but resulted in a good cleanup in
the end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/sXs
-----END PGP SIGNATURE-----
Merge tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-related
changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition is
for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It was
initiated by lockdep warning, but resulted in a good cleanup in the
end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier"
* tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
drm/i915: Add locks around audio component bind/unbind
drm/i915: Drop port_mst_index parameter from pin/eld callback
ALSA: hda - Fix missing inline for dummy snd_hdac_set_codec_wakeup()
ALSA: hda - Wake the codec up on pin/ELD notify events
ALSA: hda - allow codecs to access the i915 pin/ELD callback
drm/i915: Call audio pin/ELD notify function
drm/i915: Add audio pin sense / ELD callback
ASoC: zx296702-i2s: Fix resource leak when unload module
ASoC: sti_uniperif: Ensure component is unregistered when unload module
ASoC: au1x: psc-i2s: Convert to use devm_ioremap_resource
ASoC: sh: dma-sh7760: Convert to devm_snd_soc_register_platform
ASoC: spear_pcm: Use devm_snd_dmaengine_pcm_register to fix resource leak
ALSA: fireworks/bebob/dice/oxfw: fix substreams counting at vmalloc failure
ASoC: Clean up docbook warnings
ASoC: txx9: Convert to devm_snd_soc_register_platform
ASoC: pxa: Convert to devm_snd_soc_register_platform
ASoC: nuc900: Convert to devm_snd_soc_register_platform
ASoC: blackfin: Convert to devm_snd_soc_register_platform
ASoC: au1x: Convert to devm_snd_soc_register_platform
ASoC: qcom: Constify asoc_qcom_lpass_cpu_dai_ops
...
In case of unknown DT compatible device the ASRC OF node
possibly acquired earlier by of_parse_phandle() has
to be put before returning from probe method.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
add wm8960 support for fsl-asoc-card
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust set DAI format function in fsl_ssi driver
so it doesn't fail and clears RXDIR in AC'97 mode.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instantiate AC'97 CODEC in fsl_ssi driver AC'97 mode.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check whether setting AC'97 ops succeeded and clean them
on removal so the fsl_ssi driver can be reloaded.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 bus can support asymmetric playback/capture rates
so enable them in this case in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 DAI driver struct need the same probe method as
I2S one to setup DMA params in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fabio Estevam