The requirement for these was removed in:
0a16893397
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a port of cedb655a3a
to older asics. Fixes a possible divide by 0 if the harvest
register is invalid.
v2: drop some additional harvest munging.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Doesn't seem necessary, the GART table memory should be persistent.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Moving the pm resume up in the init order to fix
dpm seems to have regressed somes cases with the old
pm code. Move it back to late resume.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to free the uvd ring. Also reshuffle gart tear down to
happen after uvd tear down.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we are not able to properly initialize one of the gpu
engines for buffer paging, we limit vram to the size of
the cpu visible aperture. We generally either use the gfx
or dma engine to do this. Clean up the size limiting code
to only adjust the size based on what ring is selected
for buffer paging rather than making assumptions about which
engine is selected for paging.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
There's not much information still available on
r6xx, so r6xx is based on guess-work.
v2: put behind module parameter
v3: add IGP check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fill in asic family specific versions rather than
using the generic version. This lets us handle asic
specific differences more easily. In this case, we
disable sw swapping of the rtpr writeback value on
r6xx+ since the hw does it for us. Fixes bogus
rptr readback on BE systems.
v2: remove missed cpu_to_le32(), add comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need more control over the ordering of dpm init with
respect to the rest of the asic. Specifically, the SMC
has to be initialized before the rlc and cg/pg. The pm
code currently initializes late in the driver, but we need
it to happen much earlier so move pm handling into the asic
specific callbacks.
This makes dpm more reliable and makes clockgating work
properly on CIK parts and should help on SI parts as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to reorder the driver init sequence to better accomodate
dpm which needs to be loaded earlier in the init sequence. Move
fw init up so that it's available for dpm init.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The vram scratch buffer needs to be initialized
before the mc is programmed otherwise we program
0 as the GPU address of the default GPU fault
page. In most cases we put vram at zero anyway and
reserve a page for the legacy vga buffer so in practice
this shouldn't cause any problems, but better to make
it correct.
Was changed in:
6fab3febf6
Reported-by: FrankR Huang <FrankR.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Similar to separating the UVD code, just put the DMA
functions into separate files.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our different hardware blocks are actually completely
separated, so it doesn't make much sense any more to
structure the code by pure chipset generations.
Start restructuring the code by separating our the UVD block.
v2: updated commit message
v3: rebased and restructurized start/stop functions for kv dpm.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that we have callbacks for [rw]ptr handling we can
remove the special handling for the DMA rings and use
the callbacks instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hardware just doesn't support this correctly.
Disable it before we accidentally write anywhere we shouldn't.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we PG (powergate) UVD, we need to re-initialize it
before we can use it again.
v2: rebase on UVD stop fixes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise just reinitialize from scratch on resume,
and so make it more likely to succeed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For r6xx+ asics. This mirrors the behavior of pre-r6xx
asics. We need to program the MC even if something
else in startup() fails. Failure to do so results in
an unusable GPU.
Based on a fix from: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Removing the clock/power or resetting the VCPU can cause
hangs if that happens in the middle of a register write.
Stall the memory and register bus before putting the VCPU
into reset. Keep it in reset when unloading the module or
suspending.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changing the UVD BOs offset on suspend/resume doesn't work because the VCPU
internally keeps pointers to it. Just keep it always pinned and save the
content manually.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=66425
v2: fix compiler warning
v3: fix CIK support
Note: a version of this patch needs to go to stable.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.
A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
* rv515_init (rv515.c)
* radeon_irq_kms_init (radeon_irq_kms.c)
* drm_irq_install (drm_irq.c)
* radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
* rs600_irq_process (rs600.c)
* radeon_fence_process - due to SW interrupt (radeon_fence.c)
* radeon_fence_read (radeon_fence.c)
* hang due to RREG32(-1)
The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.
This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.
Bug reports:
https://bugzilla.redhat.com/show_bug.cgi?id=845745https://bugs.launchpad.net/ubuntu/+source/linux/+bug/561789https://bbs.archlinux.org/viewtopic.php?id=156964
Signed-off-by: Adis Hamzić <adis@hamzadis.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The chip id for SUMO2 isn't used.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Tested-By: Dave Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of duplicating the code over and over again, just use a single
function to handle the clock calculations.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just power down the PLL when we get a VCLK or DCLK of zero.
Enabling the bypass mode early should also allow us to
switch UVD clocks on the fly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: set UVD tiling config for rv730
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Just everything needed to decode videos using UVD.
v6: just all the bugfixes and support for R7xx-SI merged in one patch
v7: UVD_CGC_GATE is a write only register, lockup detection fix
v8: split out VRAM fallback changes, remove support for RV770,
add support for HEMLOCK, add buffer sizes checks
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a per-asic MC (memory controller) mask which holds the
mak address mask the asic is capable of. Use this when
calculating the vram and gtt locations rather using asic
specific functions or limiting everything to 32 bits.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is required to get the reference clock used
by the gfx engine for things like timestamps. Fixes
support for GL extensions the use timestamps on
certain boards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- r6xx actually uses a slightly different packet format,
although both formats seem to work ok.
- r7xx doesn't have the count multiple of 2 limitation.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Let's allow GCC to optimize better.
This exposed some five unused functions, but this patch doesn't remove them.
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This check the root ports supported link speeds and enables
GEN2 mode if the 5.0 GT link speed is available.
The first 3.0 cards are SI so they will probably need more investigation.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Before emitting any indirect buffer, emit the offset of the next
valid ring content if any. This allow code that want to resume
ring to resume ring right after ib that caused GPU lockup.
v2: use scratch registers instead of storing it into memory
v3: skip over the surface sync for ni and si as well
v4: use SET_CONFIG_REG instead of PACKET0
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Making it easier to control when it is executed.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Just reinitialize the shader content on resume instead.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The IB pool is in gart memory, so it is completely
superfluous to unpin / repin it on suspend / resume.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
For a normal suspend/resume we allready wait for
the rings to be empty, and for a suspend/reasume
in case of a lockup we REALLY don't want to wait
for anything.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Call it in the asic startup callback on all asics.
Previously r600 and rv770 called it in the startup
and resume callbacks while all the other asics called
it in the startup callback.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiling group size is always 256bits on r6xx/r7xx/r8xx/9xx. Also fix and
simplify render backend map. This now properly sets up the backend map
on r6xx-9xx which should improve 3D performance.
Vadim benchmarked also:
Some benchmarks on juniper (5750), fullscreen 1920x1080,
first result - kernel 3.4.0+ (fb21affa), second - with these patches:
Lightsmark: 91 fps => 123 fps +35%
Doom3: 74 fps => 101 fps +36%
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher