This file was never enabled in the mainline kernel, new ongoing work on
battery driver by Thomas Kunze makes it completely obsolete, so remove
it now.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
CM-X300 can be assembled with different NAND flashes from different
manufacturers. Adding their configuration to the kernel is impractical,
therefore we will use the default NAND controller settings set up by the
bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Setup gpio-keys for EzX phones
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add a call to pxa_set_ac97_info() to enable the audio support.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
csb726 used obsolete and not working out-of-tree driver smc911x.
Switch it to use new smsc911x driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
I'm not going to maintain separate defconfigs for magician and hx4700.
This should probably be renamed to htcpxa_defconfig.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add voltage regulation capability to pxa2xx cpufreq
driver. The cpufreq will ask for a "vcc_core" regulator to
the regulator framework.
If a regulator is found at probe time, it will be used with
values specified in PXA270 Electrical, Mechanical, and
Thermal Specifications.
If not, it will be assumed for now that frequency change
will work without voltage control. This assumes that the
IPL/SPL installs sane values to an existing voltage
regulator (ie. voltage high enough to support the full
range).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA processors have several low-power modes. Currently kernel supports
only one of these modes for PM_SUSPEND_MEM.
This patch adds ability to set desired suspend mode for PXA27x based
machines.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
As reported by Aric Blumer, the pxa27x_udc driver does work
with pxa3xx devices. Add support into device files.
Reported-by: Aric Blumer <aric@sdgsystems.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Matt Reimer <mattjreimer@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The default value is 16 IRQs. Zylonite needs 32, ASIC3 based boards need 70.
My problem is still that due to the way IRQ_GPIO is hardcoded, ASIC3 based boards
need 70 IRQs starting at IRQ_BOARD_START. If I define ASIC3 IRQs similar to LoCoMo
or SA1111, things break as soon as something selects PXA_HAVE_BOARD_IRQS.
Increasing the default number of board IRQs to 70 instead doesn't seem very nice.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The PXA_PWM config option is really redundant since the introduction
of HAVE_PWM, replace that with HAVE_PWM to avoid confusion.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PWMs on PXA168/910 start at number 1 instead of 0, (i.e. PWM1/2/3/4 instead
of PWM0/1/2/3 on PXA25x/PXA27x/PXA3xx). Allow this number to be specified
in pwm_id_table.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] update mach-types
[ARM] Add cmpxchg support for ARMv6+ systems (v5)
[ARM] barriers: improve xchg, bitops and atomic SMP barriers
Gemini: Fix SRAM/ROM location after memory swap
MAINTAINER: Add F: entries for Gemini and FA526
[ARM] disable NX support for OABI-supporting kernels
[ARM] add coherent DMA mask for mv643xx_eth
[ARM] pxa/palm: fix PalmLD/T5/TX AC97 MFP
[ARM] pxa: add parameter to clksrc_read() for pxa168/910
[ARM] pxa: fix the incorrectly defined drive strength macros for pxa{168,910}
[ARM] Orion: Remove explicit name for platform device resources
[ARM] Kirkwood: Correct MPP for SATA activity/presence LEDs of QNAP TS-119/TS-219.
[ARM] pxa/ezx: fix pin configuration for low power mode
[ARM] pxa/spitz: provide spitz_ohci_exit() that unregisters USB_HOST GPIO
[ARM] pxa: enable GPIO receivers after configuring pins
[ARM] pxa: allow gpio_reset drive high during normal work
[ARM] pxa: save/restore PGSR on suspend/resume.
The flat loader uses an architecture's flat_stack_align() to align the
stack but assumes word-alignment is enough for the data sections.
However, on the Xtensa S6000 we have registers up to 128bit width
which can be used from userspace and therefor need userspace stack and
data-section alignment of at least this size.
This patch drops flat_stack_align() and uses the same alignment that
is required for slab caches, ARCH_SLAB_MINALIGN, or wordsize if it's
not defined by the architecture.
It also fixes m32r which was obviously kaput, aligning an
uninitialized stack entry instead of the stack pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add cmpxchg/cmpxchg64 support for ARMv6K and ARMv7 systems
(original patch from Catalin Marinas <catalin.marinas@arm.com>)
The cmpxchg and cmpxchg64 functions can be implemented using the
LDREX*/STREX* instructions. Since operand lengths other than 32bit are
required, the full implementations are only available if the ARMv6K
extensions are present (for the LDREXB, LDREXH and LDREXD instructions).
For ARMv6, only 32-bits cmpxchg is available.
Mathieu :
Make cmpxchg_local always available with best implementation for all type sizes (1, 2, 4 bytes).
Make cmpxchg64_local always available.
Use "Ir" constraint for "old" operand, like atomic.h atomic_cmpxchg does.
Change since v3 :
- Add "memory" clobbers (thanks to Nicolas Pitre)
- removed __asmeq(), only needed for old compilers, very unlikely on ARMv6+.
Note : ARMv7-M should eventually be ifdefed-out of cmpxchg64. But it's not
supported by the Linux kernel currently.
Put back arm < v6 cmpxchg support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mathieu Desnoyers pointed out that the ARM barriers were lacking:
- cmpxchg, xchg and atomic add return need memory barriers on
architectures which can reorder the relative order in which memory
read/writes can be seen between CPUs, which seems to include recent
ARM architectures. Those barriers are currently missing on ARM.
- test_and_xxx_bit were missing SMP barriers.
So put these barriers in. Provide separate atomic_add/atomic_sub
operations which do not require barriers.
Reported-Reviewed-and-Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dmitry Eremin-Solenikov