Commit Graph

310728 Commits

Author SHA1 Message Date
Bing Zhao 38e8b7d977 mwifiex: shorten per channel scan time
Currently the scan time per channel for active scanning is set to
200ms. It takes quite a while to finsh scanning on all channels,
especially with a dual band configuration.

Change the per channel scan time settings to the following values:

passive scan: 110ms
active scan: 30ms
specific scan: 30ms

Above settings have been tested on x86 and arm platforms.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11 14:59:43 -04:00
John W. Linville b6038961df Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Conflicts:
	drivers/net/wireless/iwlwifi/iwl-eeprom.c
2012-06-11 14:50:59 -04:00
John W. Linville 2e48686835 Merge tag 'nfc-next-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-3.0 2012-06-11 14:46:04 -04:00
John W. Linville 934b9d1ed7 wl18xx: avoid some -Wformat warnings
CC      drivers/net/wireless/ti/wl18xx/main.o
drivers/net/wireless/ti/wl18xx/main.c: In function ‘wl18xx_conf_init’:
drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘long unsigned int’ [-Wformat]
drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat]

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-08 14:24:53 -04:00
Luciano Coelho bf34e68352 Merge branch 'wl12xx-next' into for-linville 2012-06-08 16:43:19 +03:00
Arik Nemtsov 3e3947fffc wlcore/wl12xx/wl18xx: make NVS file optional for wl18xx
Don't spew errors when we can't find the NVS file in wlcore. Instead
fail the wl12xx boot HW op if the NVS isn't found.

Take this opportunity to remove some dead code from register_hw()
which looks for the NVS again needlessly.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:52:06 +03:00
Arik Nemtsov 17d97719dc wl18xx: clean up phy module parameters
Give all wl18xx phy module paramters -1 as a default value, indicating
the paramter was not set. Add previous default values to the default
18xx priv conf structure.

Remove the board_type field from wl18xx priv. The field with the same
name inside the phy conf is good enough for our purposes.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:42:09 +03:00
Arik Nemtsov d61c6b5550 wl18xx: align wl18xx_conf_phy with FW variant and remove it
wl18xx_conf_phy represents part of the FW native wl18xx_mac_and_phy_params
structure. Remove it and replace the phy part of the wl18xx conf with the
FW bound structure. This allows us to set/override all members.

Increment the wlconf version to ensure compatibility with the new
structure

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:42:09 +03:00
Ido Reis 8dd8e53c6f wl18xx: update fw statistics
Aligned to the struct in FW 8.2.0.0.91 and updated the debugfs entries
accordingly.

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:41:56 +03:00
Arik Nemtsov e27454b013 wl18xx: allow FW-log by default for PG2.0
This is supported by new FW versions (.88+).

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:19 +03:00
Luciano Coelho 640dfb9b85 wl18xx: read configuration structure from a binary file
Instead of using the hardcoded configuration structure, try to read it
from a "firmware" file called wl18xx-conf.bin.  If the file doesn't
exist, fall back to the hardcoded version.  If the file exists but is
illegal, bail out.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:08 +03:00
Luciano Coelho 18b70ac9c7 wlcore/wl18xx: export conf struct in a debugfs file
Add conf file header structure, magic and version values and export
the entire conf struct in debugfs.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:08 +03:00
Luciano Coelho 34bacf73c6 wlcore/wl18xx: the conf structs must be packed so they can be exported
Since we are now going to export the conf structure and read it from a
file, it should be packed to avoid surprises with padding bytes.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:08 +03:00
Luciano Coelho b551a3c9eb wlcore: use u8 instead of enum for bcn_filt_mode
Since we will export the conf structure as a file, we need to use well
defined types.  Instead of using enum, whose size may vary, use u8 for
bcn_filt_mode instead.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:08 +03:00
Luciano Coelho 648f6ed9f7 wlcore/wl18xx/wl12xx: use u8 instead of bool for host_fast_wakeup_support
The conf structure is going to be exported to a file, so we should use
only well defined types.  bool is not well defined and may vary from
platform to platform, so change the host_fast_wakeup_support type to
u8 instead.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:08 +03:00
Luciano Coelho 9c6ead570c wlcore: export raw binary with the FW statistics in debugfs
Instead of parsing all the binary data returned by the firmware, we
should simply export the binary and let the userspace do the parsing.

This commit adds a new file to debugfs to do that.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:08 +03:00
Luciano Coelho f74ea74b82 wl18xx: add support to clear FW statistics
This patch calls ACX_CLEAR_STATISTICS to clear the firmware
statistics.  The trigger is a new debugfs file called
clear_fw_statistics in the fw_stats directory.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:07 +03:00
Eyal Shapira 3e8d69352b wlcore: add debugfs control over rx interrupt pacing
Add control over several conf fields which combined
control the rx interrupt pacing mechanism, that is avoiding
getting an interrupt following a single frame rx but instead
have the FW trigger the interrupt only after a certain
amount of frames received or a timeout.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:07 +03:00
Eyal Shapira bc8e261233 wlcore: add support macros to easily add conf debugfs entries
The current debugfs code contains too much code duplication
of bolierplate code. Add some macro magic to avoid this and
enable adding new debugfs entries by using just a few lines.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08 09:14:07 +03:00
Grant Erickson e16de2c4fc wl12xx: Add support for an external 26 MHz crystal source
Add support for an external 26 MHz crystal source.

[Changed wl->ref_clock to priv->ref_clock -- Luca.]

Signed-off-by: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:14:41 +03:00
Ido Reis 9fccc82e19 wl18xx: pad only last frame in aggregration buffer for PG2
In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.

[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]

[Make the pre_pkt_send operation optional -- Luca]

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:11:06 +03:00
Ido Reis f5755fe96c wl18xx: PG2.0 HW Watch dog interrupt support
In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).

[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]

Signed-off-by: Orit Brayer <orit@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:11:01 +03:00
Ido Reis 16ea473321 wl18xx: FW/PHY arguments added for PG2
PG2 requires 4 new parameters that to be passed to the PHY.

Use the actual PHY initialization struct size for the mem size of the
PHY_INIT section, to account for additions in params.

[Make sure PG1 still gets the original struct - Arik]

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:10:57 +03:00
Ido Reis 73395a79df wl18xx: support PG2 version of the chip
PG2 has a unique chip id. It supports similar HW quirks.

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:10:52 +03:00
Ido Reis 4085f641e7 wl18xx: fix PHY_INIT addresses mem size
was hardcoded 252, now uses the parameters struct size.

Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07 18:10:48 +03:00
Johannes Berg 2eb278e083 mac80211: unify SW/offload remain-on-channel
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.

This fixes a number of small issues with the ROC
implementation:
 * offloaded remain-on-channel couldn't be queued,
   now we can queue it as well, if needed
 * in iwlwifi (the only user) offloaded ROC is
   mutually exclusive with scanning, use the new
   queue to handle that case -- I expect that it
   will later depend on a HW flag

The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.

The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.

Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:31:18 -04:00
Johannes Berg 196ac1c13d mac80211: do remain-on-channel while idle
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.

Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.

Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:33 -04:00
Johannes Berg 491b26b402 wireless: update wireless URLs
The preferred URL is http://wireless.kernel.org/
rather than http://linuxwireless.org/, update all
URLs to point there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:32 -04:00
Sujith Manoharan 196fb860ce ath9k: Resync beacons properly
After a chip reset, the beacon timers have to re-programmed
correctly for a station in associated state. Use the PS flags
to ensure that this is done after a TSF sync happens, otherwise
the driver ends up using incorrect values for TBTT/DTIM in
powersave mode.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:32 -04:00
Sujith Manoharan 07c15a3ffd ath9k: Fix powersave locking
The 'ps_flags' is used/accessed in a variety of contexts
and requires proper locking. Use 'sc_pm_lock' appropriately.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:32 -04:00
Sujith Manoharan b74713d04e ath9k: Handle fatal interrupts properly
When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately.  Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan 781b14a315 ath9k: Use atomic operations
The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan 8da07830e1 ath9k: Move LNA code to antenna.c
And use a helper function to setup antennae after a reset.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:31 -04:00
Sujith Manoharan af68abadac ath9k: Fix work handling
* Currently, there is no synchronization between the reset
  work and the tx-poll work. Fix this and make sure that we
  bail out properly if a reset work is in progress.

* Cleanup the PLL WAR and enable it for AR9340 too and
  use a helper for restarting work/timers after a reset.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Sujith Manoharan ef1b6cd9a1 ath9k: Group link monitoring logic
Add link.c and move all the link/connection monitoring
code to it.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Rajkumar Manoharan 6995fb805e ath9k: improve BT FTP/PAN performance
When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:30 -04:00
Rajkumar Manoharan 153dccd467 ath9k_hw: fix power state for MCI
Program MCI related power registers only if MCI interrupts
are enabled. This could help to reduce power consumptions when
WLAN alone is enabled in BT coex chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan c9ae6ab4c7 ath: do not update cycle counters with sleep mode
When the chip is waking up from sleep state, the cycle counters
might have incorrect readings. So it is better not to update those
readings with software counters.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan 0603143e47 ath9k: BT coex performance tuning for AR9462
Use smaller aggregation limit and increasing aggregation threshold
for osla that could improve wlan performance when there is HID profile.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:29 -04:00
Rajkumar Manoharan 99922a45e9 ath9k_hw: fix BT RF performance
When software rfkill is triggered, before put the chip in reset
state, give LNA and SPDT control to BT to make sure BT can have
good RF performance.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan c8b6fbe1f1 ath9k_hw: configure ar9462 switching regulator
Enable WLAN and BT mode for switching regulator discontinuous
orverride for AR9462 chips.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan 9dc08eceb7 ath9k_hw: program BT to control SPDT
program BT to control SPDT everytime while loading switch table
from eeprom.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan 4fb7175bbd ath9k_hw: fix IQ calibration chain index
The chain index to perform IQ calibration is counted to number of valid
tx chains and then used for indexing chain specific registers. If the
chainmask is set to 0x2 (i.e chain 1 only), still it accesses chain 0
registers for chain 1. So use real chain index instead sequential one.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:28 -04:00
Rajkumar Manoharan 4f6bd1a8df ath9k: cleanup MCI indentation
Fix bad indentation & if nesting to lose about two levels
of unnecessary indentation.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:27 -04:00
Rajkumar Manoharan 5d294a1680 ath9k_hw: update ar9462 initval table to fix rx
The wrong ADC sample phase that happen between awake and
network/full sleep will lead to improper rx noisefloor
calibration.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:27 -04:00
Sujith Manoharan e6930c4b32 ath9k: Use separate operational flags for BTCOEX
Also, use atomic operations to check the flags.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan 4cb54fa3a2 ath9k: Remove SC_OP_OFFCHANNEL
mac80211's IEEE80211_CONF_OFFCHANNEL can be used directly
to track offchannel state. Also pass the correct boolean
value to ath9k_hw_startpcureceive().

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan 2fd5d35bc8 ath9k_hw: Fix variable usage
Exposed by sparse:
ar9003_mci.c:1134:31: warning: Using plain integer as NULL pointer

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:26 -04:00
Sujith Manoharan 97ba515a20 ath9k: Add MCI interrupt to debugfs statistics
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:25 -04:00
Sujith Manoharan 31604cf0a7 ath9k_hw: Cleanup power mode API
The 'setChip' variable is unused, remove it and
simplify the functions.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06 15:20:25 -04:00