Adds basic XDP support i.e attaching a BPF program to an
interface. Also takes care of allocating separate Tx queues
for XDP path and for network stack packet transmission.
This patch doesn't support handling of any of the XDP actions,
all are treated as XDP_PASS i.e packets will be handed over to
the network stack.
Changes also involve allocating one receive buffer per page in XDP
mode and multiple in normal mode i.e when no BPF program is attached.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of unnecessary double pointer references and type casting
in receive buffer allocation code.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimized CQE handling with below changes
- Feeing descriptors back to SQ in bulk i.e once per NAPI
instance instead for every CQE_TX, this will reduce number
of atomic updates to 'sq->free_cnt'.
- Checking errors in CQE_TX and CQE_RX before calling appropriate
fn()s to update error stats i.e reduce branching.
Also removed debug messages in packet handling path which otherwise
causes issues if DEBUG is enabled.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive buffer's physical address or iova will anyway not
go beyond 49bits, since it is the max supported HW address.
As per perf, updating bitfields i.e buf_addr:42 in RBDR
descriptor entry consumes lots of cpu cycles, hence changed
it to a 64bit field with alignment requirements taken care of.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for page recycling for allocating receive buffers
to reduce cost of refilling RBDR ring. Also got rid of using
compound pages when pagesize is 4K, only order-0 pages now.
Only page is recycled, DMA mappings still needs to be done for
every receive buffer allocated due to following constraints
- Cannot have just one receive buffer per 64KB page.
- There is just one buffer ring shared across 8 Rx queues, so
buffers of same page can go to any Rx queue.
- HW gives buffer address where packet has been DMA'ed and not
the index into buffer ring.
This makes it not possible to resue DMA mapping info. So unfortunately
have to go through costly mapping route for every buffer.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
TimeSync/"V1 frame format support"/"V2 frame format support" on
the TX side. Set the associated bits based on the user request.
2. ptp4l application fails to operate in Peer Delay mode. Following
changes are needed to fix this,
a. Driver should enable (set to 0) DA #1-related bits for IPv4,
IPv6 and MAC destination addresses in these registers:
NIG_REG_TX_LLH_PTP_RULE_MASK
NIG_REG_LLH_PTP_RULE_MASK
b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
be set to 0x0 in all modes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Tx timestamping data structures are not protected against the
concurrent access in the Tx paths. Protecting the same using atomic
bit locks.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IOT2000 is industrial controller platform, derived from the Intel
Galileo Gen2 board. The variant IOT2020 comes with one LAN port, the
IOT2040 has two of them. They can be told apart based on the board asset
tag in the DMI table.
Based on patch by Sascha Weisenberger.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is enslaved to a VRF master, its router interface (RIF)
needs to be destroyed (if exists) and a new one created using the
corresponding virtual router (VR).
>From the driver's perspective, the above is equivalent to an inetaddr
event sent for this netdev. Therefore, when a port netdev (or its
uppers) are enslaved to a VRF master, call the same function that
would've been called had a NETDEV_UP was sent for this netdev in the
inetaddr notification chain.
This patch also fixes a bug when a LAG netdev with an existing RIF is
enslaved to a VRF. Before this patch, each LAG port would drop the
reference on the RIF, but would re-join the same one (in the wrong VR)
soon after. With this patch, the corresponding RIF is first destroyed
and a new one is created using the correct VR.
Fixes: 7179eb5acd ("mlxsw: spectrum_router: Add support for VRFs")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or says:
================
mlx5 neigh update
This series (whose code name is 'neigh update') from Hadar, enhances the
mlx5 TC IP tunnel offloads to deal with changes to tunnel destination
neighbours used in offloaded flows which involved encapsulation.
In order to keep track on the validity state of such neighbours, we register
a netevent notifier callback and act on NEIGH_UPDATE events: if a neighbour
becomes valid, offload the related flows to HW (the other way around when
neigh becomes invalid) and similarly when a neigh mac addresses changes.
Since this traffic is offloaded from the host OS, the neighbour for the IP
tunnel destination can mistakenly become STALE and deleted by the kernel
since its 'used' value wasn't changed. To address that, we proactively
update the neighbour 'used' value every DELAY_PROBE_TIME seconds, using
time stamps generated by the existing driver code for HW flow counters.
We use the DELAY_PROBE_TIME_UPDATE event to adjust the frequency of the updates.
Prior to the core of the series, there's a patch from Saeed that introduces an
extendable vport representor implementation scheme. It provides a separation
between the eswitch to the netdev related aspects of the representors.
We would like to thank Ido Schimmel and Ilya Lesokhin for their coaching && advice
through the long design and review cycles while we struggled to understand and
(hopefully correctly) implement the locking around the different driver flows(..) .
- Or.
=================
Misc Updates:
From Tariq:
Some small performance and trivial code optimization for mlx5 netdev driver
- Optimize poll ICOSQ completion queue
- Use prefetchw when a write is to follow
- Use u8 as ownership type in mlx5e_get_cqe()
From Eran:
- Disable LRO by default on specific setups
From Eli:
- Small cleanup for E-Switch to avoid redundant allocation
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZBeGlAAoJEEg/ir3gV/o+AuMH/2OfS+diXrTMU90tQGfucurg
cPuv2qSGzSzcyFOjMUKL/hgj+y8HcUNZVSqts/LPhUj5CbR8On2jo/3XZb405SMX
1eAffpD5JxDGm4xQCADwkDMRVOuWNbXlTceRMbD+8vDtboTDEZwbaXX20En6MIEW
qcQPX0wv7/u8VpxGlhch2RRvl7+zBhhGCLNpwzkE5K+RggIPguE+F2hLpm+SH9PD
AOHSuwGWnE40In8dZIPqsEnUsmsC9LmUQ17ip8S8dEtGDHMvwDelsKGZcRGMuwoz
wSxpVTWn5JaU0EwN0t+rYtERFH18SqboG3OFwqb27qtRns6ALXIx3Dj1bb9sVBo=
=3qOg
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-04-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2017-04-30
Or says:
================
mlx5 neigh update
This series (whose code name is 'neigh update') from Hadar, enhances the
mlx5 TC IP tunnel offloads to deal with changes to tunnel destination
neighbours used in offloaded flows which involved encapsulation.
In order to keep track on the validity state of such neighbours, we register
a netevent notifier callback and act on NEIGH_UPDATE events: if a neighbour
becomes valid, offload the related flows to HW (the other way around when
neigh becomes invalid) and similarly when a neigh mac addresses changes.
Since this traffic is offloaded from the host OS, the neighbour for the IP
tunnel destination can mistakenly become STALE and deleted by the kernel
since its 'used' value wasn't changed. To address that, we proactively
update the neighbour 'used' value every DELAY_PROBE_TIME seconds, using
time stamps generated by the existing driver code for HW flow counters.
We use the DELAY_PROBE_TIME_UPDATE event to adjust the frequency of the updates.
Prior to the core of the series, there's a patch from Saeed that introduces an
extendable vport representor implementation scheme. It provides a separation
between the eswitch to the netdev related aspects of the representors.
We would like to thank Ido Schimmel and Ilya Lesokhin for their coaching && advice
through the long design and review cycles while we struggled to understand and
(hopefully correctly) implement the locking around the different driver flows(..) .
- Or.
=================
Misc Updates:
From Tariq:
Some small performance and trivial code optimization for mlx5 netdev driver
- Optimize poll ICOSQ completion queue
- Use prefetchw when a write is to follow
- Use u8 as ownership type in mlx5e_get_cqe()
From Eran:
- Disable LRO by default on specific setups
From Eli:
- Small cleanup for E-Switch to avoid redundant allocation
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing the PTP related initialization from slowpath start,
the remaining PTT entry is required only in case CONFIG_RFS_ACCEL is set.
Otherwise, it leads to a warning due to it being unused.
Fixes: d179bd1699 ("qed: Acquire/release ptt_ptp lock when enabling/disabling PTP")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output to the RDMA driver whether DPM mode is enabled or disabled in
the HW and if so what is the number of WIDs it supports
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating doorbell BAR partitioning round up the number of
CPUs to the nearest power of 2 so the size of the DPI (per user
section) configured in the hardware will be stored properly and
not truncated.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mechanism to verify RoCE resources are released prior to freeing the
bitmaps. If this is not the case, print what resources were not released.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the posting of the ramrod for the purpose of TID deregistration
fails, abort the deregistration operation without using the FW's
return code.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal RoCE SQE QP state isn't being used. Instead we mark the
QP as in regular error state.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use time_before_eq for time comparison more safe and dealing
with timer wrapping to be future-proof.
Signed-off-by: Karim Eshapa <karim.eshapa@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to carry error messages to the user via the netlink extended
ack message attribute.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistakes in printk message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presumably we never hit this return, but static checkers complain that
we need to unlock so we may as well fix that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that we're holding a mutex on this error
path. Let's goto exit instead of returning directly.
Fixes: b0bccb69eb ("qed: Change locking scheme for VF channel")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hip06 and hip07 SoCs, phy connect to mdio bus.The mdio
module is probed with module_init, and, as such,
is not guaranteed to probe before the HNS driver. So we need
to support deferred probe.
We check for probe deferral in the mac init, so we not init DSAF
when there is no mdio, and free all resource, to later learn that
we need to defer the probe.
Signed-off-by: lipeng <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hip06 and hip07 SoCs, the interrupt lines from the
DSAF controllers are connected to mbigen hw module.
The mbigen module is probed with module_init, and, as such,
is not guaranteed to probe before the HNS driver. So we need
to support deferred probe.
Signed-off-by: lipeng <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For legacy reasons NFP FW may be compiled to DMA packets to a constant
offset into the buffer and use the space before it for metadata. This
ensures that packets data always start at a certain offset regardless of
the amount of preceding metadata.
If rx offset is set to 0 there may still be up to 64 bytes of metadata
but metadata will start at the beginning of the buffer, instead of:
data_start_offset = rx_offset - meta_len
Even though we make the buffers larger to accommodate up to 64 bytes of
metadata, if there is only N bytes of metadata, we will end up with
N bytes of headroom and 64 - N bytes of tailroom. Therefore we can't
rely on that space for XDP headroom. Make sure we always allocate
full 256 bytes. This, unfortunately, means we can't fit the headroom
on an u8 any more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the required Service Process ABI version is still tied
to max ID of known commands. For new NSP commands we are adding
we are checking if NSP version is recent enough on command-by-command
basis. The driver doesn't have to force the device to have the
very latest flash, anything newer than 0.8 should do.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading TX queue indexes from the device memory on each interrupt
is expensive. It's doubly expensive with XDP running since we have
two TX rings to check there. If the software indexes indicate that
the TX queue is completely empty, however, we don't need to look at
the device completion index at all.
The queuing CPU is doing a wmb() before kicking the device TX so
we should be safe to assume on the CPU handling the completions will
never see old value of the software copy of the index.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the RX path we follow the "drop if allocation of replacement
buffer fails" rule. With XDP we extended that to the TX action,
so if XDP prog returned TX but allocation of replacement RX buffer
failed, we will drop the packet.
To improve our XDP TX performance extend the idea of rings being
always full to XDP TX rings. Pre-fill the XDP TX rings with RX
buffers, and when XDP prog returns TX action swap the RX buffer
with the next buffer from the TX ring.
XDP TX complete will no longer free the buffers but let them
sit on the TX ring and wait for swap with RX buffer, instead.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon allocate RX buffers for caching on XDP TX rings.
The rx_ring parameter passed to nfp_net_rx_alloc_one() is not
actually used, remove it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Or points out in commit 423b3aecf2 ("net/mlx4: Change ENOTSUPP
to EOPNOTSUPP"), ENOTSUPP is NFS specific error. Replace it with
EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace pattern
int status;
...
status = func(...);
return status;
by
return func(...);
No functional change intented.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse bnx2x_null_format_ver() in functions where it's appropriated
instead of open coded variant.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use scnprintf() when printing version instead of custom open coded variants.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 83a77e9ec4, the phydev irq is explicitly set to PHY_POLL when
there is no pdata. It doesn't work on DT enabled platforms because the
phydev irq is already set by libphy before.
Fixes: 83a77e9ec4 ("net: macb: Added PCI wrapper for Platform Driver.")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-04-30
This series contains updates to i40e and i40evf only.
Jake provides majority of the changes in this series, starting with the
renaming of a flag to avoid confusion. Then renamed a variable to a
more meaningful name to clarify what is actually being done and to
reduce confusion. Amortizes the wait time when initializing or disabling
lots of VFs by using i40e_reset_all_vfs() and
i40e_vsi_stop_rings_no_wait(). Cleaned up a unnecessary delay since
pci_disable_sriov() already has its own delay, so need to add a additional
delay when removing VFs. Avoid using the same name flags for both
vsi->state and pf->state, to make code review easier and assist future
work to use the correct state field when checking bits. Use
DECLARE_BITMAP() to ensure that we always allocate enough space for flags.
Replace hw_disabled_flags with the new _AUTO_DISABLED flags, which are
more readable because we are not setting an *_ENABLED flag to
disable the feature.
Alex corrects a oversight where we were not reprogramming the ports
after a reset, which was causing us to lose all of the receive tunnel
offloads.
Arnd Bergmann moves the declaration of a local variable to avoid a
warning seen on architectures with larger pages about an unused variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
struct esw_mc_addr is a small struct that can be part of struct
mlx5_eswitch. Define it as a field and not as a pointer and save the
kzalloc call and then error flow handling.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We will activate the HW LRO only on servers with PCI BW > MAX LINK BW,
or when PCI BW > 16Gbps. On other cases we do not want LRO by default as
LRO sessions might get timeout and add redundant software overhead.
Tested:
ethtool -k <ifs-name> | grep large-receive-offload
On systems with and without the limitations.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
CQE ownership indication is as small as a single bit.
Use u8 to speedup the comparison.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
"prefetchw()" prefetches the cacheline for write. Use it for
skb->data, as soon we'll be copying the packet header there.
Performance:
Single-stream packet-rate tested with pktgen.
Packets are dropped in tc level to zoom into driver data-path.
Larger gain is expected for smaller packets, as less time
is spent on handling SKB fragments, making the path shorter
and the improvement more significant.
---------------------------------------------
packet size | before | after | gain |
64B | 4,113,306 | 4,778,720 | 16% |
1024B | 3,633,819 | 3,950,593 | 8.7% |
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
UMR operations are more frequent and important.
Check them first, and add a compiler branch predictor hint.
According to current design, ICOSQ CQ can contain at most one
pending CQE per napi. Poll function is optimized accordingly.
Performance:
Single-stream packet-rate tested with pktgen.
Packets are dropped in tc level to zoom into driver data-path.
Larger gain is expected for larger packet sizes, as BW is higher
and UMR posts are more frequent.
---------------------------------------------
packet size | before | after | gain |
64B | 4,092,370 | 4,113,306 | 0.5% |
1024B | 3,421,435 | 3,633,819 | 6.2% |
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The user can change delay_first_probe_time parameter through sysctl.
Listen to NETEVENT_DELAY_PROBE_TIME_UPDATE notifications and update the
intervals for updating the neighbours 'used' value periodic task and
for flow HW counters query periodic task.
Both of the intervals will be update only in case the new delay prob
time value is lower the current interval.
Since the driver saves only one min interval value and not per device,
the users will be able to set lower interval value for updating
neighbour 'used' value periodic task but they won't be able to schedule
a higher interval for this periodic task.
The used interval for scheduling neighbour 'used' value periodic task is
the minimal delay prob time parameter ever seen by the driver.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When IP tunnel encapsulation rules are offloaded, the kernel can't see
the traffic of the offloaded flow. The neighbour for the IP tunnel
destination of the offloaded flow can mistakenly become STALE and
deleted by the kernel since its 'used' value wasn't changed.
To make sure that a neighbour which is used by the HW won't become
STALE, we proactively update the neighbour 'used' value every
DELAY_PROBE_TIME period, when packets were matched and counted by the HW
for one of the tunnel encap flows related to this neighbour.
The periodic task that updates the used neighbours is scheduled when a
tunnel encap rule is successfully offloaded into HW and keeps re-scheduling
itself as long as the representor's neighbours list isn't empty.
Add, remove, lookup and status change operations done over the
representor's neighbours list or the neighbour hash entry encaps list
are all serialized by RTNL lock.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to offload TC encap rules, the driver does a lookup for the IP
tunnel neighbour according to the output device and the destination IP
given by the user.
To keep tracking after the validity state of such neighbours, we keep
the neighbours information (pair of device pointer and destination IP)
in a hash table maintained at the relevant egress representor and
register to get NETEVENT_NEIGH_UPDATE events. When getting neighbour update
netevent, we search for a match among the cached neighbours entries used for
encapsulation.
In case the neighbour isn't valid, we can't offload the flow into the
HW. We cache the flow (requested matching and actions) in the driver and
offload the rule later, when the neighbour is resolved and becomes
valid.
When a flow is only cached in the driver and not offloaded into HW
yet, we use EAGAIN return value to mark it internally, the TC ndo still
returns success.
Listen to kernel neighbour update netevents to trace relevant neighbours
validity state:
1. If a neighbour becomes valid, offload the related rules to HW.
2. If the neighbour becomes invalid, remove the related rules from HW.
3. If the neighbour mac address was changed, update the encap header.
Remove all the offloaded rules using the old encap header from the HW
and insert new rules to HW with updated encap header.
Access to the neighbors hash table is protected by RTNL lock of its
caller or by the table's spinlock.
Details of the locking/synchronization among the different actions
applied on the neighbour table:
Add/remove operations - protected by RTNL lock of its caller (all TC
commands are protected by RTNL lock). Add and remove operations are
initiated only when the user inserts/removes a TC rule into/from the driver.
Lookup/remove operations - since the lookup operation is done from
netevent notifier block, RTNL lock can't be used (atomic context).
Use the table's spin lock to protect lookups from TC user removal operation.
bh is used since netevent can be called from a softirq context.
Lookup/add operations - The hash table access functions are taking
care of the protection between lookup and add operations.
When adding/removing encap headers and rules to/from the HW, RTNL lock
is used. It can happen when:
1. The user inserts/removes a TC rule into/from the driver (TC commands
are protected by RTNL lock of it's caller).
2. The driver gets neighbour notification event, which reports about
neighbour validity status change. Before adding/removing encap headers
and rules to/from the HW, RTNL lock is taken.
A neighbour hash table entry should be freed when its encap list is empty.
Since The neighbour update netevent notification schedules a neighbour
update work that uses the neighbour hash entry, it can't be freed
unconditionally when the encap list becomes empty during TC delete rule flow.
Use reference count to protect from freeing neighbour hash table entry
while it's still in use.
When the user asks to unregister a netdvice used by one of the neigbours,
neighbour removal notification is received. Then we take a reference on the
neighbour and don't free it until the relevant encap entries (and flows) are
marked as invalid (not offloaded) and removed from HW.
As long as the encap entry is still valid (checked under RTNL lock) we
can safely access the neighbour device saved on mlx5e_neigh struct.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add hash table to the representors which is to be used by the next patch
to save neighbours information in the driver.
In order to offload IP tunnel encapsulation rules, the driver must find
the tunnel dst neighbour according to the output device and the
destination address given by the user. The next patch will cache the
neighbors information in the driver to allow support in neigh update
flow for tunnel encap rules.
The neighbour entries are also saved in a list so we easily iterate over
them when querying statistics in order to provide 'used' feedback to the
kernel neighbour NUD core.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The nud_state and hardware address fields are protected by the neighbour
lock, we should acquire it before accessing those parameters.
Use this lock to avoid inconsistency between the neighbour validity state
and it's hardware address.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of relaying on the 'flow->rule' pointer value which can be
valid or invalid (in case the FW returns an error while trying to offload
the rule), monitor the rule state using a flag.
In downstream patch which adds support to IP tunneling neigh update
flow, a TC rule could be cached in the driver and not offloaded into the
HW. In this case, the flow handle pointer stays NULL.
Check the offloaded flag to properly deal with rules which are currently
not offloaded when querying rule statistics.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Passing output device parameter to the helper functions that deal with
creation of encapsulation headers is redundant. Output device parameter
can be defined inside those helpers, no need to pass it. Refactor the code by
removing the parameter from the function signature.
This patch doesn't change any functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The encap entry structure isn't manipulated by the eswitch code,
hence it can/needs to be removed from the eswitch header.
Do that, and change it to have mlx5e_ prefix.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Encap wise, the tc eswitch flow attribute struct needs to have
only the encap ID which is programmed later to the HW and none
of the higher level encap params, fix that.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make representor netdev private data extendable by adding new struct
"mlx5e_rep_priv" and use it as the rep netdev private data struct
instead of directly pointing to mlx5_eswitch_rep.
Added new en_rep.h header file to contain all representor related
definitions and prototypes, and moved all representor specific logic
into en_rep.c.
Needed for downstream patches to extend representor functionality to
support neighbour update.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add support for 38.4MHz frequency is required for PTP
on CannonLake. SYSTIM frequency adjustment attributes for TIMINCA are
get/set dependent on the hardware clock frequency for a different
types of adapters. 38.4MHz frequency supported by CannonLake
and active once time synchronisation mechanism was enabled
Changed abbreviation from Hz to HZ to be compliant checkpatch code style
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The propagation of CannonLake mac type to driver functionality
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219 (6) and i219 (7) are the next LOM generations that will be
available on the nextIntel Client platform (CannonLake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On architectures with larger pages, we get a warning about an unused variable:
drivers/net/ethernet/intel/i40evf/i40evf_main.c: In function 'i40evf_configure_rx':
drivers/net/ethernet/intel/i40evf/i40evf_main.c:690:21: error: unused variable 'netdev' [-Werror=unused-variable]
This moves the declaration into the #ifdef to avoid the warning.
Fixes: dab86afdbb ("i40e/i40evf: Change the way we limit the maximum frame size for Rx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This matches the ordering of how we free stuff during reset and remove.
It also makes logical sense because we set the interrupts based on the
number of queues. Currently this doesn't really matter in practice.
However a future patch moves the assignment of num_active_queues into
i40evf_alloc_queues, which is required by
i40evf_set_interrupt_capability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The flag used by the common code and PF code is I40E_FLAG_FD_ATR_ENABLED,
not *FDIR*. It turns out none of the txrx code actually shared with the
VF driver actually checks the ATR flag. This is made even more obvious
by the typo in the VF header file.
Let's just remove the flag from the VF driver since it's not needed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hw_disabled_flags field was added as a way of signifying that
a feature was automatically or temporarily disabled. However, we
actually only use this for FDir features. Replace its use with new
_AUTO_DISABLED flags instead. This is more readable, because you aren't
setting an *_ENABLED flag to *disable* the feature.
Additionally, clean up a few areas where we used these bits. First, we
don't really need to set the auto-disable flag for ATR if we're fully
disabling the feature via ethtool.
Second, we should always clear the auto-disable bits in case they somehow
got set when the feature was disabled. However, avoid displaying
a message that we've re-enabled the feature.
Third, we shouldn't be re-enabling ATR in the SB ntuple add flow,
because it might have been disabled due to space constraints. Instead,
we should just wait for the fdir_check_and_reenable to be called by the
watchdog.
Overall, this change allows us to simplify some code by removing an
extra field we didn't need, and the result should make it more clear as
to what we're actually doing with these flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already set pairs to the value of adapter->num_active_queues. This
value is limited by vsi_res->num_queue_pairs and num_online_cpus(). This
means that pairs by definition is already smaller than
num_online_cpus()*2, so we don't even need to bother with this check.
Lets just remove it and update the comment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of assuming our flags fit within an unsigned long, use
DECLARE_BITMAP which will ensure that we always allocate enough space.
Additionally, use __I40E_STATE_SIZE__ markers as the last element of the
enumeration so that the size of the BITMAP is compile-time assigned
rather than programmer-time assigned. This ensures that potential future
flag additions do not actually overrun the array. This is especially
important as 32bit systems would only have 32bit longs instead of 64bit
longs as we generally have assumed in the prior code.
This change also removes a dereference of the state fields throughout
the code, so it does have a bit of code churn. The conversions were
automated using sed replacements with an alternation
s/&(vsi->back|vsi|pf)->state/\1->state/
s/&adapter->vsi.state/adapter->vsi.state/
For debugfs, we modify the printing so that we can display chunks of the
state value on new lines. This ensures that we can print the entire set
of state values. Additionally, we now print them as 08lx to ensure that
they display nicely.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid using the same named flags for both vsi->state and pf->state. This
makes code review easier, as it is more likely that future authors will
use the correct state field when checking bits. Previous commits already
found issues with at least one check, and possibly others may be
incorrect.
This reduces confusion as it is more clear what each flag represents,
and which flags are valid for which state field.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The delay was added because of a desire to ensure that the VF driver can
finish up removing. However, pci_disable_sriov already has its own
ssleep() call that will sleep for an entire second, so there is no
reason to add extra delay on top of this by using msleep here. In
practice, an msleep() won't have a huge impact on timing but there is no
real value in keeping it, so lets just simplify the code and remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just as we do in i40e_reset_all_vfs, save some time when freeing VFs by
amortizing the wait time for stopping queues. We can use
i40e_vsi_stop_rings_no_wait() to begin the process of stopping all the
VF rings at once. Then, once we've started the process on each VF we can
begin waiting for the VFs to stop. This helps reduce the total wait time
by a large factor.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a major oversight in that we were not reprogramming the
ports after a reset. As a result we completely lost all of the Rx tunnel
offloads on receive including Rx checksum, RSS on inner headers, and ATR.
The fix for this is pretty standard as all we needed to do is reset the
filter bits to pending for all active filters and schedule the sync event.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The .index field of i40e_udp_port_config represents the udp port number.
Rename this variable to port so that it is more obvious.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When allocating a large number of VFs, the driver previously used
i40e_reset_vf in a sequence. Just as when performing a normal reset,
this accumulates a large amount of delay for handling all of the VFs in
sequence. This delay is mainly due to a hardware requirement to wait
after initiating a reset on the VF.
We recently added a new function, i40e_reset_all_vfs() which can be used
to amortize the delay time, by first triggering all VF resets, then
waiting once, and finally cleaning up and allocating the VFs. This is
almost as good as truly running the resets in parallel.
In order to avoid sending a spurious reset message to a client
interface, we have a check to see whether we've assigned
pf->num_alloc_vfs yet. This was originally intended as a way to
distinguish the "initialization" case from the regular reset case.
Unfortunately, this means that we can't directly use i40e_reset_all_vfs
yet. Lets avoid this check of pf->num_alloc_vfs by replacing it with
a proper VSI state bit which we can use instead. This makes the
intention much clearer and allows us to re-use the i40e_reset_all_vfs
function directly.
Change-ID: I694279b37eb6b5a91b6670182d0c15d10244fd6e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These flags represent the state of the VF at various times. Do not
spell them as _STAT_ which can be confusing to readers who may think
these refer to statistics.
Change-ID: I6bc092cd472e8276896a1fd7498aced2084312df
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 5093bb965a ("powerpc/QE: switch to the cpm_muram
implementation"), muram area is not part of immrbar mapping anymore
so immrbar_virt_to_phys() is not usable anymore.
Fixes: 5093bb965a ("powerpc/QE: switch to the cpm_muram implementation")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Li Yang <pku.leo@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
The RSS key is being repopulated every time the interface is brought up
regardless of whether there is an existing value. If the user sets the RSS
key and the interface is brought up (e.g. reset), the user specified RSS
key will be overwritten.
This patch changes the rss_key to a pointer so we can check to see if the
key has been populated and preserve it accordingly.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mailbox support for getting RETA and RSS is available for only 82599 and
x540; a previous patch reversed the logic and these adapters were
returning not supported.
Also, the NACK check in ixgbevf_get_rss_key_locked() was checking for the
command IXGBE_VF_GET_RETA instead of IXGBE_VF_GET_RSS_KEY.
This patch corrects both issues by correcting the logic and checking for
the right command.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RSS key is being repopulated every time the interface is brought up
regardless of whether there is an existing value. If the user sets the RSS
key and the interface is brought up (e.g. reset), the user specified RSS
key will be overwritten.
This patch changes the rss_key to a pointer so we can check to see if the
key has been populated and preserve it accordingly.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for new 1000Base-T device based on X550EM_X MAC
type. All PHY operations are disabled as the PHY is controlled
by FW.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, there is no logic that allows a VF's MAC address to be removed
from the RAR table.
Allow the user to specify a zero MAC address in order to clear the VF's
MAC address from the RAR table. This functionality is also utilized by
libvirt when removing VFs.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IXGBEVF_QUEUE_STATS_LEN is based on ixgebvf_stats, not ixgbe_stats.
This change fixes a bug where ethtool -S displayed some empty fields.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flush the macvlan filters on VF reset to avoid conflict with other VFs that
may end up using the same MAC address.
The main change here is the call to ixgbe_set_vf_macvlan() with index 0.
Moved ixgbe_set_vf_macvlan() in front of ixgbe_vf_reset_event() to avoid
adding a prototype.
Reported-by: Sritej Kanakadandi Sritej Rama <skanakad@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current XDP implementation hits the tail on every XDP_TX return
code. This patch changes driver behavior to only hit the tail after
packet processing is complete.
With this patch I can run XDP drop programs @ 14+Mpps and XDP_TX
programs are at ~13.5Mpps.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A couple design choices were made here. First I use a new ring
pointer structure xdp_ring[] in the adapter struct instead of
pushing the newly allocated XDP TX rings into the tx_ring[]
structure. This means we have to duplicate loops around rings
in places we want to initialize both TX rings and XDP rings.
But by making it explicit it is obvious when we are using XDP
rings and when we are using TX rings. Further we don't have
to do ring arithmatic which is error prone. As a proof point
for doing this my first patches used only a single ring structure
and introduced bugs in FCoE code and macvlan code paths.
Second I am aware this is not the most optimized version of
this code possible. I want to get baseline support in using
the most readable format possible and then once this series
is included I will optimize the TX path in another series
of patches.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Basic XDP drop support for ixgbe. Uses READ_ONCE/xchg semantics on XDP
programs instead of RCU primitives as suggested by Daniel Borkmann and
Alex Duyck.
v2: fix the build issues seen w/ XDP when page sizes are larger than 4K
and made minor fixes based on feedback from Jakub Kicinski
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent firmware change fixed an issue to acquire the PHY semaphore before
accessing PHY registers. This led to a case where SW can issue a device
reset clearing the MDIO registers. This patch makes SW acquire the PHY
semaphore before issuing a device reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Lindgren reports a kernel oops that resulted from my compile-time
fix on the default config. This shows two problems:
a) configurations that did not already enable PTP_1588_CLOCK will
now miss the cpts driver
b) when cpts support is disabled, the driver crashes. This is a
preexisting problem that we did not notice before my patch.
While the second problem is still being investigated, this modifies
the dependencies again, getting us back to the original state, with
another 'select NET_PTP_CLASSIFY' added in to avoid the original
link error we got, and the 'depends on POSIX_TIMERS' to hide
the CPTS support when turning it on would be useless.
Cc: stable@vger.kernel.org # 4.11 needs this
Fixes: 07fef36234 ("cpsw/netcp: cpts depends on posix_timers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code for acquiring/releasing ptt_ptp lock to ptp specific
implementations i.e., ptp_enable()/disable() respectively.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch deletes the qed_ptp.h file which is not required.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds necessary changes to the driver to use qed resource
locking functionality. Currently the ptp initialization is spread
between driver probe/open implementations, associated APIs are
qede_ptp_register_phc()/qede_ptp_start(). Clubbed this functionality
into single API qed_ptp_enable() to simplify the usage of qed resource
locking implementation. The new API will be invoked in the probe path.
Similarly the ptp clean-up code is moved to qede_ptp_disable() which
gets invoked in the driver unload path.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for per-port resource lock in favour of PTP.
PTP module acquires/releases the MFW resource lock while enabling/
disabling the PTP on the interface. The PF instance which has the
ownership of this resource lock will get the exclusive access to the
PTP clock functionality on the port.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds API for default initialization of the MFW resource
locking.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sub crq structures are initialized in interrupt context while
handling the response to crqs when negotiating capabilities for
the driver. The sub crqs do not need to be initialized at this point
and can be moved to being done from ibmvnic_init. Moving the init
of the sub crqs to ibmvnic_init also allows use to allocate the
memory with GFP_KERNEL instead of GFP_ATOMIC.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the sending of capability request crqs and the initialization
of sub crqs into their own routines. This is a first step to moving
the allocation of sub-crqs out of interrupt context.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENODEV from the no PHY found error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Fixes: b5a9ee7cf3 ("qed: Revise QM configuration")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCBX app_data array is initialized with the incorrect values for
personality field. This would prevent offloaded protocols from
honoring the PFC.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is unused and probably was unintentionally left while
moving completion queue mapping in submit function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware channel APIs support between
VF and PF for tunnelling configuration for the VFs.
According to that configuration VFs can run VXLAN/GENEVE/GRE
tunnels over it with tunnel features offloaded.
Using these APIs VF can also request for UDP ports configuration
to the PF, although PF and it's child VFs share the same port.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures UDP ports locally instead of
configuring them in deferred context which would be
helpful in synchronizing UDP ports configuration for VFs
which will be enabled in further patches.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables tunnel offloads via ndo_features_check()
if given UDP port is not offloaded to hardware. This in turn
allows to run multiple tunnel interfaces using different UDP ports.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tunnel feature offloads based on hw configuration
at initialization time instead of enabling them always.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the tunnel APIs to use per tunnel
info instead of using bitmasks for all tunnels and also
uses single struct to hold the data to prepare multiple
variant of tunnel configuration ramrods to be sent to the hardware.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: dd248f1bc6 ("sfc: Add PCI ID for Solarflare 8000 series 10/40G NIC")
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function pci_find_ext_capability() may return 0, which is an invalid
address. In function qlcnic_sriov_virtid_fn(), its return value is used
without validation. This may result in invalid memory access bugs. This
patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+9NgAAoJEEg/ir3gV/o+/RIH/2Ua/FvxWtnaXhLj9GPELdGx
4Q2+ub43Q/F2cU2rIP0S/Ki3fEeOfk+IR87bvKBc+KTcLwUcBQloLjiLTxVOXSNY
+NmE7T1gl7Sb4NzJ9lDVYbmUlDzWZixbFkQdZ6nZJTKecXuN+xooL7EWosyZKuFd
FlDpIMacWlH2bMb/1U4lClg9MMPz8e37B9kJ0Vy/lert7NkVdXgYbPI2pKxweF9i
7yH0pNLKYvIQOubZZ9A7gPhk+OGp6xLAo9pJF6xG8tQuXI59Fz6tcKGbNb8GdzZu
g12EY2c75BxWJofPtvsDDM5i8ypwF3tfCqxDjw4h9F0wHGJv6tlh51vyuYA8ceg=
=KnUF
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-04-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-04-22
This series contains some mlx5 fixes for net.
For your convenience, the series doesn't introduce any conflict with
the ongoing net-next pull request.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5: E-Switch, Correctly deal with inline mode on ConnectX-5") kernels >= 4.10
("net/mlx5e: Fix ETHTOOL_GRXCLSRLALL handling") kernels >= 4.8
("net/mlx5e: Fix small packet threshold") kernels >= 4.7
("net/mlx5: Fix driver load bad flow when having fw initializing timeout") kernels >= 4.4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code refreshing the eth port state was trying to update state
of all ports of the card. Unfortunately to safely walk the port
list we would have to hold the port lock, which we can't due to
lock ordering constraints against rtnl.
Make the per-port sync refresh and async refresh of all ports
completely separate routines.
Fixes: 172f638c93 ("nfp: add port state refresh")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP headroom should not be included in free list buffer size.
Fixes: 6fe0c3b438 ("nfp: add support for xdp_adjust_head()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve identifying information from the NSP. For now it only
contains versions of firmware subcomponents.
Signed-off-by: David Brunecz <david.brunecz@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling memcpy to shift metadata out of the way for XDP to run
seems like an overkill. The most common metadata contents are
8 bytes containing type and flow hash. Simply parse the metadata
before we run XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmap may destroy changes CPU made to the buffer. To make XDP
run correctly on non-x86 platforms we should use the
DMA_ATTR_SKIP_CPU_SYNC attribute.
Thanks to using the attribute we can now push the sync operation to the
common code path from XDP handler.
A little bit of variable name reshuffling is required to bring the
code back to readable state.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse and compiler warnings fixes from Stephen Hemminger.
From Roi Dayan and Or Gerlitz, Add devlink and mlx5 support for controlling
E-Switch encapsulation mode, this knob will enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+5cRAAoJEEg/ir3gV/o+5c8H/1/khPzy26B2lWyjPC8CRCQF
eSd0tiHLgIqbZTbnIHTR+NbZ/SUFaukoJi8OKn1fGFHCCajWvPP4xkENVKrUdi3q
kOgNZb/R1V0j6SdELyoMalFPjAscTgdmwYMnry+vcjOxJ+H2uUTnMKXwFf8IsBjz
EINy8oZ5jZcejmft0c2O5HN4Bt/7U5ttM3CroAdcvPT9lq2DFJL2uCABhTO/1DdY
b7uVa47FnkqxX19Ebn7fjp5r3diGYOmCPMjdC89C//rbkLB8FN61EkcSLpGY3YNm
djmCPQ+xaa3ielmBpOk3AMayFEtYW0nDMj9eWECVByadRQZ2qz9wTVXBp5CX9zg=
=E3Jt
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-04-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-04-22
Sparse and compiler warnings fixes from Stephen Hemminger.
From Roi Dayan and Or Gerlitz, Add devlink and mlx5 support for controlling
E-Switch encapsulation mode, this knob will enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err message and rejoin
line.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_put_padto() fails then it frees the skb. I shifted that code
up a bit to make my error handling a little simpler.
Fixes: a0d2f20650 ("Renesas Ethernet AVB PTP clock driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use offset_in_page() macro instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change restricts the PF in multi-host mode from setting any port
level PHY configuration. The settings are controlled by firmware in
Multi-Host mode.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the additional flag in bnxt_hwrm_func_qcfg() before allowing
DCBX to be done in host mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for 100G link speed reporting for Broadcom BCM57454
ASIC in ethtool command.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .ndo_get_vf_config() is returning the wrong qos attribute. Fix
the code that checks and reports the qos and spoofchk attributes. The
BNXT_VF_QOS and BNXT_VF_LINK_UP flags should not be set by default
during init. time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver gets the RoCE app priority set/delete call through DCBNL,
the driver will send the information to the firmware to set up the
priority VLAN tag for RDMA traffic.
[ New version using the common ETH_P_IBOE constant in if_ether.h ]
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error is encountered during transmit we need to free the
skb instead of returning TX_BUSY.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate that the napi structs exist before trying to disable them
at driver close.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a common routine for setting the link state for the vnic adapter.
This update moves the sending of the crq and waiting for the link state
response to a common place. The new routine also adds handling of
resending the crq in cases of getting a partial success response.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be initializing the stats token in the same place we
initialize the other resources for the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling a fatal error in the driver, there can be additional
error information provided by the vios. This information is not
always present, so only retrieve the additional error information
when present.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a modification in the PAPR+ specification which now
defines a previously reserved value for vNIC capabilities. It indicates
whether the system firmware performs a VLAN header stripping on all VLAN
tagged received frames, in case it does, the behavior expected is for
the ibmvnic driver to be responsible for inserting the VLAN header.
Reported-by: Manvanthara B. Puttashankar <mputtash@in.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Along with 5 TX queues, 5 RX queues are allocated at the beginning of
device probe. However, only the real number of TX queues is set. Configure
the real number of RX queues as well.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereference "skb" to get "skb->len" so we should probably do that
step before freeing the skb.
Fixes: eea221ce48 ("tc35815 driver update (take 2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for static/local dcbx mode. In this mode
adapter brings up the dcbx link with locally configured parameters
instead of performing the dcbx negotiation with the peer. The feature
is useful when peer device/switch doesn't support dcbx.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the older firmware there was no distinction between RoCE and RoCEv2
whereas the newer firmware (8.15.3.0) allows us to configure each
independently. Driver need to populate the RoCEv2 data in its specific
structure.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have observed a sudden spike in rx/tx_packets and rx/tx_bytes
reported under /proc/net/dev. There is a race in mlx5e_update_stats()
and some of the get-stats functions (the one that we hit is the
mlx5e_get_stats() which is called by ndo_get_stats64()).
In particular, the very first thing mlx5e_update_sw_counters()
does is 'memset(s, 0, sizeof(*s))'. For example, if mlx5e_get_stats()
is unlucky at one point, rx_bytes and rx_packets could be 0. One second
later, a normal (and much bigger than 0) value will be reported.
This patch is to use a 'struct mlx5e_sw_stats temp' to avoid
a direct memset zero on priv->stats.sw.
mlx5e_update_vport_counters() has a similar race. Hence, addressed
together. However, memset zero is removed instead because
it is not needed.
I am lucky enough to catch this 0-reset in rx multicast:
eth0: 41457665 76804 70 0 0 70 0 47085 15586634 87502 3 0 0 0 3 0
eth0: 41459860 76815 70 0 0 70 0 47094 15588376 87516 3 0 0 0 3 0
eth0: 41460577 76822 70 0 0 70 0 0 15589083 87521 3 0 0 0 3 0
eth0: 41463293 76838 70 0 0 70 0 47108 15595872 87538 3 0 0 0 3 0
eth0: 41463379 76839 70 0 0 70 0 47116 15596138 87539 3 0 0 0 3 0
v2: Remove memset zero from mlx5e_update_vport_counters()
v1: Use temp and memcpy
Fixes: 9218b44dcc ("net/mlx5e: Statistics handling refactoring")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-04-20
This series contains updates to e1000, e1000e, igb/vf and ixgb.
Tobias Klauser cleans up e1000, ixgb and igbvf from having a local
function or structure for netdev stats.
Bernd Faust fixes an issue for 82579 devices, where the clock frequency
was being incorrectly set for these devices. These devices only support
96MHz, so make sure they are set to use only that.
Yury Kylulin extends the work Jake and Alex did for ixgbe in MAC filter
handling into the igb driver.
Kim Tatt Chuah enables igb to wake up by packet and to read the necessary
Wake Up Status (WUS) and Wake Up Packet Memory (WUPM) registers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Handler for ETHTOOL_GRXCLSRLALL must set info->data to the size
of the table, regardless of the amount of entries in it.
Existing code does not do that, and this breaks all usage of ethtool -N
or -n without explicit location, with this error:
rmgr: Invalid RX class rules table size: Success
Set info->data to the table size.
Tested:
ethtool -n ens8
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1 loc 55
ethtool -n ens8
ethtool -N ens8 delete 1023
ethtool -N ens8 delete 55
Fixes: f913a72aa0 ("net/mlx5e: Add support to get ethtool flow rules")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
RX packet headers are meant to be contained in SKB linear part,
and chose a threshold of 128.
It turns out this is not enough, i.e. for IPv6 packet over VxLAN.
In this case, UDP/IPv4 needs 42 bytes, GENEVE header is 8 bytes,
and 86 bytes for TCP/IPv6. In total 136 bytes that is more than
current 128 bytes. In this case expand header flow is reached.
The warning in skb_try_coalesce() caused by a wrong truesize
was already fixed here:
commit 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()").
Still, we prefer to totally avoid the expand header flow for performance reasons.
Tested regular TCP_STREAM with iperf for 1 and 8 streams, no degradation was found.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When UAR is released, we deallocate the device resource, but
don't unmmap the UAR mapping memory.
Fix the leak by unmapping this memory.
Fixes: a6d51b6861 ('net/mlx5: Introduce blue flame register allocator)
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Otherwise the code that fills the ipv6 encapsulation headers could be writing
beyond the allocated headers buffer.
Fixes: ce99f6b97f ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Otherwise the code that fills the ipv4 encapsulation headers could be writing
beyond the allocated headers buffer.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On ConnectX5 the wqe inline mode is "none" and hence the FW
reports MLX5_CAP_INLINE_MODE_NOT_REQUIRED.
Fix our devlink callbacks to deal with that on get and set.
Also fix the tc flow parsing code not to fail anything when
inline isn't required.
Fixes: bffaa91658 ('net/mlx5: E-Switch, Add control for inline mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If FW is stuck in initializing state we will skip the driver load, but
current error handling flow doesn't clean previously allocated command
interface resources.
Fixes: e3297246c2 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix sparse warning about missing prototypes. The rx/tx code path
defines functions with prototypes in ipoib.h.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix sparse warnings in recent ipoib support.
The RDMA functions are not used yet, hide behind #ifdef.
Based on comment, they will eventually be local so make static.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement the devlink e-switch encapsulation control set and get
callbacks. Apply the value set by the user on the switchdev offloads
mode when creating the fast FDB table where offloaded rules will be set.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor the creation of the fast path FDB table that holds the
offloaded rules in SRIOV switchdev mode into it's own function.
This will be used in the next patch to be able and re-create the
table under different settings without going through legacy mode.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver use phy_start_aneg() in arc_emac_open() to bring
up PHY. But phy_start() function is more appropriate for this purposes.
Besides that it call phy_start_aneg() as part of PHY startup sequence
it also can correctly bring up PHY from error and suspended states.
So the patch replace phy_start_aneg() to phy_start().
Also the patch add call to phy_stop() to arc_emac_stop() to allow
the PHY device to be fully suspended when the interface is unused.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-04-19
This series contains updates to i40e and i40evf only, most notable being
the addition of trace points for BPF programs.
Tobias Klauser updates i40evf to use net_device stats struct instead
of a local private copy.
Preethi updates the VF driver to not enable receive checksum offload by
default for tunneled packets.
Alex fixes an issue he introduced when he converted the code over to
using the length field to determine if a descriptor was done or not.
Mitch adds the ability to dump additional information on the VFs, which
is not available through 'ip link show' using debugfs.
Scott adds trace points to the drivers so that BPF programs can be
attached for feature testing and verification.
Jingjing adds admin queue functions for Pipeline Personalization Profile
commands.
Jake does most of the heavy lifting in this series, starting with the
a reduction in the scope of the RTNL lock being held while resetting VFs
to allow multiple PFs to reset in a timely manner. Factored out the
direct queue modification so that we are able to re-use the code.
Reduced the wait time for admin queue commands to complete, since we were
waiting a minimum of a millisecond, when in practice the admin queue
command is processed often much faster. Cleaned up code (flag) we never
use. Make the code to resetting all the VFs optimized for parallel
computing instead of the current way is a serialized fashion, to help
reduce the time it takes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bounce buffer is not used in the ibmvnic driver, just
get rid of it.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the allocation of memory for the sub crq structs and their
associated pages to allocate zero-filled memory.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham