If a device is torn down by a hotplug slot driver it's marked as removed
and marked as permaantly failed. There's no point in trying to recover a
permernantly failed device so it should be considered un-actionable.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-4-oohall@gmail.com
When the last device in an eeh_pe is removed the eeh_pe structure itself
(and any empty parents) are freed since they are no longer needed. This
results in a crash when a hotplug driver is involved since the following
may occur:
1. Device is suprise removed.
2. Driver performs an MMIO, which fails and queues and eeh_event.
3. Hotplug driver receives a hotplug interrupt and removes any
pci_devs that were under the slot.
4. pci_dev is torn down and the eeh_pe is freed.
5. The EEH event handler thread processes the eeh_event and crashes
since the eeh_pe pointer in the eeh_event structure is no
longer valid.
Crashing is generally considered poor form. Instead of doing that use
the fact PEs are marked as EEH_PE_INVALID to keep them around until the
end of the recovery cycle, at which point we can safely prune any empty
PEs.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-2-oohall@gmail.com
If a PCI device is removed during eeh_pe_report_edev(), between the
calls to device_lock() and device_unlock(), edev->pdev will change and
cause a crash as the wrong mutex is released.
To correct this, hold the PCI rescan/remove lock while taking a copy
of edev->pdev and performing a get_device() on it. Use this value to
release the mutex, but also pass it through to the device driver's EEH
handlers so that they always see the same device.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/3c590579a0faa24d20c826dcd26c739eb4d454e6.1565930772.git.sbobroff@linux.ibm.com
Convert existing messages, where appropriate, to use the eeh_edev_*
logging macros.
The only effect should be minor adjustments to the log messages, apart
from:
- A new message in pseries_eeh_probe() "Probing device" to match the
powernv case.
- The "Probing device" message in pnv_eeh_probe() is now generated
slightly later, which will mean that it is no longer emitted for
devices that aren't probed due to the initial checks.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ce505a0a7a4a5b0367f0f40f8b26e7c0a9cf4cb7.1565930772.git.sbobroff@linux.ibm.com
Now that struct eeh_dev includes the BDFN of it's PCI device, make use
of it to replace eeh_edev_info() with a set of dev_dbg()-style macros
that only need a struct edev.
With the BDFN available without the struct pci_dev, eeh_pci_name() is
now unnecessary, so remove it.
While only the "info" level function is used here, the others will be
used in followup work.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f90ae9a53d762be7b0ccbad79e62b5a1b4f4996e.1565930772.git.sbobroff@linux.ibm.com
The EEH_DEV_NO_HANDLER flag is used by the EEH system to prevent the
use of driver callbacks in drivers that have been bound part way
through the recovery process. This is necessary to prevent later stage
handlers from being called when the earlier stage handlers haven't,
which can be confusing for drivers.
However, the flag is set for all devices that are added after boot
time and only cleared at the end of the EEH recovery process. This
results in hot plugged devices erroneously having the flag set during
the first recovery after they are added (causing their driver's
handlers to be incorrectly ignored).
To remedy this, clear the flag at the beginning of recovery
processing. The flag is still cleared at the end of recovery
processing, although it is no longer really necessary.
Also clear the flag during eeh_handle_special_event(), for the same
reasons.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b8ca5629d27de74c957d4f4b250177d1b6fc4bbd.1565930772.git.sbobroff@linux.ibm.com
Currently, the EEH recovery process considers passed-through devices
as if they were not EEH-aware, which can cause them to be removed as
part of recovery. Because device removal requires cooperation from
the guest, this may lead to the process stalling or deadlocking.
Also, if devices are removed on the host side, they will be removed
from their IOMMU group, making recovery in the guest impossible.
Therefore, alter the recovery process so that passed-through devices
are not removed but are instead left frozen (and marked isolated)
until the guest performs it's own recovery. If firmware thaws a
passed-through PE because it's parent PE has been thawed (because it
was not passed through), re-freeze it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a parameter to eeh_clear_pe_frozen_state() that allows
passed-through PEs to be excluded. Update callers to always pass true
so that there is no change in behaviour.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a parameter to eeh_pe_state_clear() that allows passed-through PEs
to be excluded. Update callers to always pass true so that there is no
change in behaviour.
Also refactor to use direct traversal, to allow the removal of some
boilerplate.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_unfreeze_pe() performs two operations: unfreezing a PE (which may
cause firmware to unfreeze child PEs as well) and de-isolating the PE
and it's children.
To simplify this and support future work, separate out the
de-isolation and perform it at the call sites (when necessary).
There should be no change in behaviour.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 'clear_sw_state' parameter for eeh_pe_clear_frozen_state() is
redundant because it has no effect (except in the rare case of a
hardware error part way through unfreezing a tree of PEs, where it
would dangerously allow partial de-isolation before returning
failure).
It is passed down to __eeh_pe_clear_frozen_state(), and from there to
eeh_unfreeze_pe(), where it causes EEH_PE_ISOLATED to be removed
from the state of each PE during the traversal. However, when the
traversal finishes, EEH_PE_ISOLATED is unconditionally removed by a
call to eeh_pe_state_clear() regardless of the parameter's value.
So remove the flag and pass false to eeh_unfreeze_pe() (to avoid the
rare case described above, as it was before the flag was introduced).
Also, perform the recursion directly in the function and eliminate a
bit of boilerplate.
There should be no change in functionality, except as mentioned above.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function pci_ers_result_name() is a static function, although not declared
as such. This was detected by sparse in the following warning
arch/powerpc/kernel/eeh_driver.c:63:12: warning: symbol 'pci_ers_result_name' was not declared. Should it be static?
This patch simply declares the function a static.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than mixing "if (state)" blocks and gotos, convert entirely to
"if (state)" blocks to make the state machine behaviour clearer.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The wait_state member of eeh_ops does not need to be platform
dependent; it's just logic around eeh_ops.get_state(). Therefore,
merge the two (slightly different!) platform versions into a new
function, eeh_wait_state() and remove the eeh_ops member.
While doing this, also correct:
* The wait logic, so that it never waits longer than max_wait.
* The wait logic, so that it never waits less than
EEH_STATE_MIN_WAIT_TIME.
* One call site where the result is treated like a bit field before
it's checked for negative error values.
* In pseries_eeh_get_state(), rename the "state" parameter to "delay"
because that's what it is.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, eeh_pe_state_mark() marks a PE (and it's children) with a
state and then performs additional processing if that state included
EEH_PE_ISOLATED.
The state parameter is always a constant at the call site, so
rearrange eeh_pe_state_mark() into two functions and just call the
appropriate one at each site.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the name of the fields in eeh_rmv_data to clarify their usage.
Change "edev_list" to "removed_vf_list" because it does not contain
generic edevs, but rather only edevs that contain virtual functions
(which need to be removed during recovery).
Similarly, change "removed" to "removed_dev_count" because it is a
count of any removed devices, not just those in the above list.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instances of struct eeh_pe are placed in a tree structure using the
fields "child_list" and "child", so place these next to each other
in the definition.
The field "child" is a list entry, so remove the unnecessary and
misleading use of the list initializer, LIST_HEAD(), on it.
The eeh_dev struct contains two list entry fields, called "list" and
"rmv_list". Rename them to "entry" and "rmv_entry" and, as above, stop
initializing them with LIST_HEAD().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the unnecessary cast through void * on the first parameter and
remove the unused second parameter (always NULL).
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 'bus' member of struct eeh_dev is assigned to once but never used,
so remove it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a device is removed during EEH processing (either by a driver's
handler or as part of recovery), it can lead to a null dereference
in eeh_pe_report_edev().
To handle this, skip devices that have been removed.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The EEH report functions now share a fair bit of code around the start
and end of each function.
So factor out as much as possible, and move the traversal into a
custom function. This also allows accurate debug to be generated more
easily.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
[mpe: Format with clang-format]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a device without a driver is recovered via EEH, the flag
EEH_DEV_NO_HANDLER is incorrectly left set on the device after
recovery, because the test in eeh_report_resume() for the existence of
a bound driver is done before the flag is cleared. If a driver is
later bound, and EEH experienced again, some of the drivers EEH
handers are not called.
To correct this, clear the flag unconditionally after EEH processing
is complete.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To ease future refactoring, extract calls to eeh_enable_irq() and
eeh_disable_irq() from the various report functions. This makes
the report functions initial sequences more similar, as well as making
the IRQ changes visible when reading eeh_handle_normal_event().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To ease future refactoring, extract setting of the channel state
from the report functions out into their own functions. This increases
the amount of code that is identical across all of the report
functions.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The same test is done in every EEH report function, so factor it out.
Since eeh_dev_removed() needs to be moved higher up in the file,
simplify it a little while we're at it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As EEH event handling progresses, a cumulative result of type
pci_ers_result is built up by (some of) the eeh_report_*() functions
using either:
if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
if (*res == PCI_ERS_RESULT_NONE) *res = rc;
or:
if ((*res == PCI_ERS_RESULT_NONE) ||
(*res == PCI_ERS_RESULT_RECOVERED)) *res = rc;
if (*res == PCI_ERS_RESULT_DISCONNECT &&
rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
(Where *res is the accumulator.)
However, the intent is not immediately clear and the result in some
situations is order dependent.
Address this by assigning a priority to each result value, and always
merging to the highest priority. This renders the intent clear, and
provides a stable value for all orderings.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
[mpe: Minor formatting (clang-format)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The traversal functions eeh_pe_traverse() and eeh_pe_dev_traverse()
both provide their first argument as void * but every single user casts
it to the expected type.
Change the type of the first parameter from void * to the appropriate
type, and clean up all uses.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Correct two cases where eeh_pcid_get() is used to reference the driver's
module but the reference is dropped before the driver pointer is used.
In eeh_rmv_device() also refactor a little so that only two calls to
eeh_pcid_put() are needed, rather than three and the reference isn't
taken at all if it wasn't needed.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a single log line at the end of successful EEH recovery, so that
it's clear that event processing has finished.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current EEH callbacks can race with a driver unbind. This can
result in a backtraces like this:
EEH: Frozen PHB#0-PE#1fc detected
EEH: PE location: S000009, PHB location: N/A
CPU: 2 PID: 2312 Comm: kworker/u258:3 Not tainted 4.15.6-openpower1 #2
Workqueue: nvme-wq nvme_reset_work [nvme]
Call Trace:
dump_stack+0x9c/0xd0 (unreliable)
eeh_dev_check_failure+0x420/0x470
eeh_check_failure+0xa0/0xa4
nvme_reset_work+0x138/0x1414 [nvme]
process_one_work+0x1ec/0x328
worker_thread+0x2e4/0x3a8
kthread+0x14c/0x154
ret_from_kernel_thread+0x5c/0xc8
nvme nvme1: Removing after probe failure status: -19
<snip>
cpu 0x23: Vector: 300 (Data Access) at [c000000ff50f3800]
pc: c0080000089a0eb0: nvme_error_detected+0x4c/0x90 [nvme]
lr: c000000000026564: eeh_report_error+0xe0/0x110
sp: c000000ff50f3a80
msr: 9000000000009033
dar: 400
dsisr: 40000000
current = 0xc000000ff507c000
paca = 0xc00000000fdc9d80 softe: 0 irq_happened: 0x01
pid = 782, comm = eehd
Linux version 4.15.6-openpower1 (smc@smc-desktop) (gcc version 6.4.0 (Buildroot 2017.11.2-00008-g4b6188e)) #2 SM P Tue Feb 27 12:33:27 PST 2018
enter ? for help
eeh_report_error+0xe0/0x110
eeh_pe_dev_traverse+0xc0/0xdc
eeh_handle_normal_event+0x184/0x4c4
eeh_handle_event+0x30/0x288
eeh_event_handler+0x124/0x170
kthread+0x14c/0x154
ret_from_kernel_thread+0x5c/0xc8
The first part is an EEH (on boot), the second half is the resulting
crash. nvme probe starts the nvme_reset_work() worker thread. This
worker thread starts touching the device which see a device error
(EEH) and hence queues up an event in the powerpc EEH worker
thread. nvme_reset_work() then continues and runs
nvme_remove_dead_ctrl_work() which results in unbinding the driver
from the device and hence releases all resources. At the same time,
the EEH worker thread starts doing the EEH .error_detected() driver
callback, which no longer works since the resources have been freed.
This fixes the problem in the same way the generic PCIe AER code (in
drivers/pci/pcie/aer/aerdrv_core.c) does. It makes the EEH code hold
the device_lock() while performing the driver EEH callbacks and
associated code. This ensures either the callbacks are no longer
register, or if they are registered the driver will not be removed
from underneath us.
This has been broken forever. The EEH call backs were first introduced
in 2005 (in 77bd741561) but it's not clear if a lock was needed back
then.
Fixes: 77bd741561 ("[PATCH] powerpc: PCI Error Recovery: PPC64 core recovery routines")
Cc: stable@vger.kernel.org # v2.6.16+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The caller will always pass NULL for 'rmv_data' when
'eeh_aware_driver' is true, so the first two calls to
eeh_pe_dev_traverse() can be combined without changing behaviour as
can the two arms of the final 'if' block.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_reset_device() tests the value of 'bus' more than once but the
only caller, eeh_handle_normal_device() does this test itself and will
never pass NULL.
So, remove the dead tests.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is currently difficult to understand the behaviour of
eeh_reset_device() due to the way it's parameters are used. In
particular, when 'bus' is NULL, it's value is still necessary so the
same value is looked up again locally under a different name
('frozen_bus') but behaviour is changed.
To clarify this, add a new parameter 'driver_eeh_aware', and have the
caller set it when it would have passed NULL for 'bus' and always pass
a value for 'bus'. Then change any test that was on 'bus' to one on
'!driver_eeh_aware' and replace uses of 'frozen_bus' with 'bus'.
Also update the function's comment.
This should not change behaviour.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The name "frozen_bus" is misleading: it's not necessarily frozen, it's
just the PE's PCI bus.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove a test that checks if "frozen_bus" is NULL, because it cannot
have changed since it was tested at the start of the function and so
must be true here.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the EEH_PE_RECOVERING flag for a PE is managed by both the
caller and callee of eeh_handle_normal_event() (among other places not
considered here). This is complicated by the fact that the PE may
or may not have been invalidated by the call.
So move the callee's handling into eeh_handle_normal_event(), which
clarifies it and allows the return type to be changed to void (because
it no longer needs to indicate at the PE has been invalidated).
This should not change behaviour except in eeh_event_handler() where
it was previously possible to cause eeh_pe_state_clear() to be called
on an invalid PE, which is now avoided.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_handle_event(pe) does nothing other than switching
between calling eeh_handle_normal_event(pe) and
eeh_handle_special_event(). However it is only called in two places,
one where pe can't be NULL and the other where it must be NULL (see
eeh_event_handler()) so it does nothing but obscure the flow of
control.
So, remove it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The notify_resume() callback in eeh_ops is NULL on powernv, leading to
crashes:
NIP (null)
LR eeh_report_resume+0x218/0x220
Call Trace:
eeh_report_resume+0x1f0/0x220 (unreliable)
eeh_pe_dev_traverse+0x98/0x170
eeh_handle_normal_event+0x3f4/0x650
eeh_handle_event+0x54/0x380
eeh_event_handler+0x14c/0x210
kthread+0x168/0x1b0
ret_from_kernel_thread+0x5c/0xb4
Fix it by adding a check before calling it.
Fixes: 856e1eb9bd ("PCI/AER: Add uevents in AER and EEH error/resume")
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Tested-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Devices can go offline when erors reported. This patch adds a change
to the kernel object and lets udev know of error. When device resumes,
a change is also set reporting device as online. Therefore, EEH and
AER events are better propagated to user space for PCI devices in all
arches.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
SR-IOV can now be enabled for the powernv platform and pseries
platform. Therefore move the appropriate calls to machine dependent
code instead of relying on definition at compile time.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@us.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Non-highlights:
- Five fixes for the >128T address space handling, both to fix bugs in our
implementation and to bring the semantics exactly into line with x86.
Highlights:
- Support for a new OPAL call on bare metal machines which gives us a true NMI
(ie. is not masked by MSR[EE]=0) for debugging etc.
- Support for Power9 DD2 in the CXL driver.
- Improvements to machine check handling so that uncorrectable errors can be
reported into the generic memory_failure() machinery.
- Some fixes and improvements for VPHN, which is used under PowerVM to notify
the Linux partition of topology changes.
- Plumbing to enable TM (transactional memory) without suspend on some Power9
processors (PPC_FEATURE2_HTM_NO_SUSPEND).
- Support for emulating vector loads form cache-inhibited memory, on some
Power9 revisions.
- Disable the fast-endian switch "syscall" by default (behind a CONFIG), we
believe it has never had any users.
- A major rework of the API drivers use when initiating and waiting for long
running operations performed by OPAL firmware, and changes to the
powernv_flash driver to use the new API.
- Several fixes for the handling of FP/VMX/VSX while processes are using
transactional memory.
- Optimisations of TLB range flushes when using the radix MMU on Power9.
- Improvements to the VAS facility used to access coprocessors on Power9, and
related improvements to the way the NX crypto driver handles requests.
- Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew Donnellan, Aneesh
Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin Herrenschmidt, Breno Leitao,
Christophe Leroy, Christophe Lombard, Cyril Bur, Frederic Barrat, Gautham R.
Shenoy, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo Romero, Haren
Myneni, Joel Stanley, Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami
Hiramatsu, Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia Franco de
Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee, Shriya, Stephen
Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel Datwyler, Vaibhav Jain,
Vaidyanathan Srinivasan, William A. Kennington III.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rq81
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A bit of a small release, I suspect in part due to me travelling for
KS. But my backlog of patches to review is smaller than usual, so I
think in part folks just didn't send as much this cycle.
Non-highlights:
- Five fixes for the >128T address space handling, both to fix bugs
in our implementation and to bring the semantics exactly into line
with x86.
Highlights:
- Support for a new OPAL call on bare metal machines which gives us a
true NMI (ie. is not masked by MSR[EE]=0) for debugging etc.
- Support for Power9 DD2 in the CXL driver.
- Improvements to machine check handling so that uncorrectable errors
can be reported into the generic memory_failure() machinery.
- Some fixes and improvements for VPHN, which is used under PowerVM
to notify the Linux partition of topology changes.
- Plumbing to enable TM (transactional memory) without suspend on
some Power9 processors (PPC_FEATURE2_HTM_NO_SUSPEND).
- Support for emulating vector loads form cache-inhibited memory, on
some Power9 revisions.
- Disable the fast-endian switch "syscall" by default (behind a
CONFIG), we believe it has never had any users.
- A major rework of the API drivers use when initiating and waiting
for long running operations performed by OPAL firmware, and changes
to the powernv_flash driver to use the new API.
- Several fixes for the handling of FP/VMX/VSX while processes are
using transactional memory.
- Optimisations of TLB range flushes when using the radix MMU on
Power9.
- Improvements to the VAS facility used to access coprocessors on
Power9, and related improvements to the way the NX crypto driver
handles requests.
- Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew
Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Breno Leitao, Christophe Leroy, Christophe Lombard,
Cyril Bur, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven,
Guilherme G. Piccoli, Gustavo Romero, Haren Myneni, Joel Stanley,
Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami Hiramatsu,
Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia
Franco de Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee,
Shriya, Stephen Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel
Datwyler, Vaibhav Jain, Vaidyanathan Srinivasan, and William A.
Kennington III"
* tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (151 commits)
powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature
powerpc/64s: Fix masking of SRR1 bits on instruction fault
powerpc/64s: mm_context.addr_limit is only used on hash
powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation
powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary
powerpc/64s/hash: Fix fork() with 512TB process address space
powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation
powerpc/64s/hash: Fix 512T hint detection to use >= 128T
powerpc: Fix DABR match on hash based systems
powerpc/signal: Properly handle return value from uprobe_deny_signal()
powerpc/fadump: use kstrtoint to handle sysfs store
powerpc/lib: Implement UACCESS_FLUSHCACHE API
powerpc/lib: Implement PMEM API
powerpc/powernv/npu: Don't explicitly flush nmmu tlb
powerpc/powernv/npu: Use flush_all_mm() instead of flush_tlb_mm()
powerpc/powernv/idle: Round up latency and residency values
powerpc/kprobes: refactor kprobe_lookup_name for safer string operations
powerpc/kprobes: Blacklist emulate_update_regs() from kprobes
powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace
powerpc/kprobes: Disable preemption before invoking probe handler for optprobes
...
This interface is inefficient and deprecated because of the y2038
overflow.
ktime_get_seconds() is an appropriate replacement here, since it
has sufficient granularity but is more efficient and uses monotonic
time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "reset" argument passed to pci_iov_add_virtfn() and
pci_iov_remove_virtfn() is always zero since 46cb7b1bd8 ("PCI: Remove
unused SR-IOV VF Migration support")
Remove the argument together with the associated code.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
The eeh_dev struct already holds a pointer to pci_dn which it does not
exist without and pci_dn itself holds the very same pointer so just
use it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove unnecessary tags in eeh_handle_normal_event(), and add function
comments for eeh_handle_normal_event() and eeh_handle_special_event().
The only functional difference is that in the case of a PE reaching the
maximum number of failures, rather than one message telling you of this
and suggesting you reseat the device, there are two separate messages.
Suggested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_handle_special_event() is called when an EEH event is detected but
can't be narrowed down to a specific PE. This function looks through
every PE to find one in an erroneous state, then calls the regular event
handler eeh_handle_normal_event() once it knows which PE has an error.
However, if eeh_handle_normal_event() found that the PE cannot possibly
be recovered, it will free it, rendering the passed PE stale.
This leads to a use after free in eeh_handle_special_event() as it attempts to
clear the "recovering" state on the PE after eeh_handle_normal_event() returns.
Thus, make sure the PE is valid when attempting to clear state in
eeh_handle_special_event().
Fixes: 8a6b1bc70d ("powerpc/eeh: EEH core to handle special event")
Cc: stable@vger.kernel.org # v3.11+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In __eeh_clear_pe_frozen_state(), we should pass the flag's value
instead of its address to eeh_unfreeze_pe(). The isolated flag is
cleared if no error returned from __eeh_clear_pe_frozen_state(). We
never observed the error from the function. So the isolated flag should
have been always cleared, no real issue is caused because of the misused
@flag.
This fixes the code by passing the value of @flag to eeh_unfreeze_pe().
Fixes: 5cfb20b96f ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for secure and
trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and store
them as relative offsets to save space in the kernel image & memory.
- Allow building the kernel with thin archives, which should allow us to build
an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the kernel endian
from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9 Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage support,
qbman fixes/cleanup, device tree updates, and some misc cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual,
Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz, Christophe Jaillet,
Christophe Leroy, Denis Kirjanov, Elimar Riesebieter, Frederic Barrat,
Gautham R. Shenoy, Geliang Tang, Geoff Levand, Jack Miller, Johan Hovold,
Lars-Peter Clausen, Libin, Madhavan Srinivasan, Michael Neuling, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin,
Rashmica Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xOzf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.
- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"
[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]
* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...
Oliver O'Halloran