Some users of pata_falcon on Q40 have IDE disks in default
IDE little endian byte order, whereas legacy disks use
host-native big-endian byte order as on the Atari Falcon.
Add module parameter 'data_swab' to allow connecting drives
with non-native data byte order. Drives selected by the
data_swap bit mask will have their user data byte-swapped to
host byte order, i.e. 'pata_falcon.data_swab=2' will byte-swap
all user data on drive B, leaving data on drive A in native
byte order. On Q40, drives on a second IDE interface may be
added to the bit mask as bits 2 and 3.
Default setting is no byte swapping, i.e. compatibility with
the native Falcon or Q40 operating system disk format.
Cc: William R Sowerbutts <will@sowerbutts.com>
Cc: Finn Thain <fthain@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: William R Sowerbutts <will@sowerbutts.com>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
With commit 44b1fbc0f5 ("m68k/q40: Replace q40ide driver
with pata_falcon and falconide"), the Q40 IDE driver was
replaced by pata_falcon.c.
Both IO and memory resources were defined for the Q40 IDE
platform device, but definition of the IDE register addresses
was modeled after the Falcon case, both in use of the memory
resources and in including register shift and byte vs. word
offset in the address.
This was correct for the Falcon case, which does not apply
any address translation to the register addresses. In the
Q40 case, all of device base address, byte access offset
and register shift is included in the platform specific
ISA access translation (in asm/mm_io.h).
As a consequence, such address translation gets applied
twice, and register addresses are mangled.
Use the device base address from the platform IO resource
for Q40 (the IO address translation will then add the correct
ISA window base address and byte access offset), with register
shift 1. Use MMIO base address and register shift 2 as before
for Falcon.
Encode PIO_OFFSET into IO port addresses for all registers
for Q40 except the data transfer register. Encode the MMIO
offset there (pata_falcon_data_xfer() directly uses raw IO
with no address translation).
Reported-by: William R Sowerbutts <will@sowerbutts.com>
Closes: https://lore.kernel.org/r/CAMuHMdUU62jjunJh9cqSqHT87B0H0A4udOOPs=WN7WZKpcagVA@mail.gmail.com
Link: https://lore.kernel.org/r/CAMuHMdUU62jjunJh9cqSqHT87B0H0A4udOOPs=WN7WZKpcagVA@mail.gmail.com
Fixes: 44b1fbc0f5 ("m68k/q40: Replace q40ide driver with pata_falcon and falconide")
Cc: stable@vger.kernel.org
Cc: Finn Thain <fthain@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: William R Sowerbutts <will@sowerbutts.com>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The Atari Falcon PATA driver does not need anything from <asm/ide.h>.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Make it explicit that ATA host templates are not modified.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com> (for DWC AHCI SATA)
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com> (for Tegra)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230322195515.1267197-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The zero day bot reported some sparse complaints in pata_falcon.c. E.g.
drivers/ata/pata_falcon.c:58:41: warning: cast removes address space '__iomem' of expression
drivers/ata/pata_falcon.c:58:41: warning: incorrect type in argument 1 (different address spaces)
drivers/ata/pata_falcon.c:58:41: expected unsigned short volatile [noderef] [usertype] __iomem *port
drivers/ata/pata_falcon.c:58:41: got unsigned short [usertype] *
The same thing shows up in 8 places, all told. Avoid this by removing
unnecessary type casts.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Prepare for removal of the request pointer by using scsi_cmd_to_rq()
instead. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20210809230355.8186-8-bvanassche@acm.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This allows m68k q40 systems to switch from the deprecated IDE subsystem
to libata.
Enhance the byte-swapping falconide and pata_falcon platform drivers to
accept an irq resource, for use on q40. Atari ST-DMA IRQ arrangements seem
to co-exist with q40 IRQ arrangements without too much mess.
The new IO resources were added solely for the purpose of making
request_region() reservations identical to those made by q40ide: these
regions aren't used for actual IO.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/eefb7e9c2291e09fb4e065ce06bc105f05bb9e06.1623287706.git.fthain@linux-m68k.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Autoloading of Falcon IDE driver modules requires converting these
drivers to platform drivers.
Add platform device for Falcon IDE interface in Atari platform setup
code. Use this in the pata_falcon driver in place of the simple
platform device set up on the fly.
Convert falconide driver to use the same platform device that is used
by pata_falcon also. (With the introduction of a platform device for
the Atari Falcon IDE interface, the old Falcon IDE driver no longer
loads (resource already claimed by the platform device)).
Tested (as built-in driver) on my Atari Falcon.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://lore.kernel.org/r/1573008449-8226-1-git-send-email-schmitzmic@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Pull libata updates from Tejun Heo:
- Bartlomiej added pata_falcon
- Christoph is trying to remove use of static 4k buf. It's still WIP
- config cleanup around HAS_DMA
- other fixes and driver-specific changes
* 'for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (29 commits)
ata: pata_of_platform: using of_property_read_u32() helper
pata_atiixp: Don't use unconnected secondary port on SB600/SB700
libata-sff: Don't scan disabled ports when checking for legacy mode.
pata_octeon_cf: remove unused local variables from octeon_cf_set_piomode()
ahci: qoriq: added ls2088a platforms support
ahci: qoriq: report error when ecc register address is missing in dts
ahci: qoriq: added a condition to enable dma coherence
Revert "libata: switch to dynamic allocation instead of ata_scsi_rbuf"
ahci: imx: fix building without hwmon or thermal
ata: add Atari Falcon PATA controller driver
ata: pass queued command to ->sff_data_xfer method
ata: allow subsystem to be used on m68k arch
libata: switch to dynamic allocation instead of ata_scsi_rbuf
libata: don't call ata_scsi_rbuf_fill for command without a response buffer
libata: call ->scsi_done from ata_scsi_simulate
libata: remove the done callback from ata_scsi_args
libata: move struct ata_scsi_args to libata-scsi.c
libata: avoid global response buffer in atapi_qc_complete
libata-eh: Use switch() instead of sparse array for protocol strings
ata: sata_mv: Convert to devm_ioremap_resource()
...
Add Atari Falcon PATA controller driver. The major difference
when compared to legacy IDE's falconide host driver is that we
are using polled PIO mode and thus avoiding the need for STDMA
locking magic altogether.
Tested under ARAnyM emulator.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Michael Schmitz