wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most OMAP3-based boards use exactly the same code for .map_io method in
the machine_desc structure.
This patch introduces omap3_map_io and updates board-* files to use it
as .map_io method.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only difference between them is the physical address of the
uart4 port, which is only present in 36xx chips.
We don't really need to care about keeping these 2 functions, since
the decision to use uart4 is more cleanly done later when we do have
access to omap_revision variable.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: added comment for the uart4_phys]
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP v2 uses EHCI port 1 instead of EHCI port 2.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Select CONFIG_LEDS_GPIO to enable IGEP v2 LED support and control of supported
LEDs from userspace. Otherwise GPIO LEDs are exported as GPIO 26, 27 and 28 using
the gpiolib framework.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
the early_param() call in board-omap3touchbook.c expands to:
static const char __setup_str_early_touchbook_revision[]
__section(.init.rodata) _aligned(1) = tbr;
[...]
and we have a non-const variable being added to the
same section:
static struct ehci_hcd_omap_platform_data ehci_pdata
__section(.init.rodata);
because of that, gcc generates a section type conflict
which can (and actually should) be avoided by marking
const every variable marked with __initconst.
This patch fixes that for the ehci_hdc_omap_platform_data.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.
Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If not configured it will be exported as normal GPIO led.
Signed-off-by: Jonas Zetterberg <jozz@jozz.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabled VMMC2 LDO voltage regulator on TWL4030.
Added GPIO's (power down and reset) for WIFI chip.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: Jonas Zetterberg <jozz@jozz.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for flashes on IGEP v2 boards. For now
only OneNAND is supported.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for EHCI driver on IGEP v2
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for the twl4030_codec MFD on IGEP v2
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sukumar Ghorai