For the next patch we will need to know the full state of the
interrupt shadow; we will then set KVM_REQ_EVENT when one bit
is cleared.
However, right now get_interrupt_shadow only returns the one
corresponding to the emulated instruction, or an unconditional
0 if the emulated instruction does not have an interrupt shadow.
This is confusing and does not allow us to check for cleared
bits as mentioned above.
Clean the callback up, and modify toggle_interruptibility to
match the comment above the call. As a small result, the
call to set_interrupt_shadow will be skipped in the common
case where int_shadow == 0 && mask == 0.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 575203 the MCE subsystem in the Linux kernel for AMD sets bit 18
in MSR_K7_HWCR. Running such a kernel as a guest in KVM on an AMD host results
in a GPE injected into the guest because kvm_set_msr_common returns 1. This
patch fixes this by masking bit 18 from the MSR value desired by the guest.
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We encountered a scenario in which after an INIT is delivered, a pending
interrupt is delivered, although it was sent before the INIT. As the SDM
states in section 10.4.7.1, the ISR and the IRR should be cleared after INIT as
KVM does. This also means that pending interrupts should be cleared. This
patch clears upon reset (and INIT) the pending interrupts; and at the same
occassion clears the pending exceptions, since they may cause a similar issue.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I've observed kvmclock being marked as unstable on a modern
single-socket system with a stable TSC and qemu-1.6.2 or qemu-2.0.0.
The culprit was failure in TSC matching because of overflow of
kvm_arch::nr_vcpus_matched_tsc in case there were multiple TSC writes
in a single synchronization cycle.
Turns out that qemu does multiple TSC writes during init, below is the
evidence of that (qemu-2.0.0):
The first one:
0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel]
0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm]
0xffffffffa04cfd6b : kvm_arch_vcpu_postcreate+0x4b/0x80 [kvm]
0xffffffffa04b8188 : kvm_vm_ioctl+0x418/0x750 [kvm]
The second one:
0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel]
0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm]
0xffffffffa090610d : vmx_set_msr+0x29d/0x350 [kvm_intel]
0xffffffffa04be83b : do_set_msr+0x3b/0x60 [kvm]
0xffffffffa04c10a8 : msr_io+0xc8/0x160 [kvm]
0xffffffffa04caeb6 : kvm_arch_vcpu_ioctl+0xc86/0x1060 [kvm]
0xffffffffa04b6797 : kvm_vcpu_ioctl+0xc7/0x5a0 [kvm]
#0 kvm_vcpu_ioctl at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1780
#1 kvm_put_msrs at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1270
#2 kvm_arch_put_registers at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1909
#3 kvm_cpu_synchronize_post_init at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1641
#4 cpu_synchronize_post_init at /build/buildd/qemu-2.0.0+dfsg/include/sysemu/kvm.h:330
#5 cpu_synchronize_all_post_init () at /build/buildd/qemu-2.0.0+dfsg/cpus.c:521
#6 main at /build/buildd/qemu-2.0.0+dfsg/vl.c:4390
The third one:
0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel]
0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm]
0xffffffffa090610d : vmx_set_msr+0x29d/0x350 [kvm_intel]
0xffffffffa04be83b : do_set_msr+0x3b/0x60 [kvm]
0xffffffffa04c10a8 : msr_io+0xc8/0x160 [kvm]
0xffffffffa04caeb6 : kvm_arch_vcpu_ioctl+0xc86/0x1060 [kvm]
0xffffffffa04b6797 : kvm_vcpu_ioctl+0xc7/0x5a0 [kvm]
#0 kvm_vcpu_ioctl at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1780
#1 kvm_put_msrs at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1270
#2 kvm_arch_put_registers at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1909
#3 kvm_cpu_synchronize_post_reset at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1635
#4 cpu_synchronize_post_reset at /build/buildd/qemu-2.0.0+dfsg/include/sysemu/kvm.h:323
#5 cpu_synchronize_all_post_reset () at /build/buildd/qemu-2.0.0+dfsg/cpus.c:512
#6 main at /build/buildd/qemu-2.0.0+dfsg/vl.c:4482
The fix is to count each vCPU only once when matched, so that
nr_vcpus_matched_tsc holds the size of the matched set. This is
achieved by reusing generation counters. Every vCPU with
this_tsc_generation == cur_tsc_generation is in the matched set. The
match set is cleared by setting cur_tsc_generation to a value which no
other vCPU is set to (by incrementing it).
I needed to bump up the counter size form u8 to u64 to ensure it never
overflows. Otherwise in cases TSC is not written the same number of
times on each vCPU the counter could overflow and incorrectly indicate
some vCPUs as being in the matched set. This scenario seems unlikely
but I'm not sure if it can be disregarded.
Signed-off-by: Tomasz Grabiec <tgrabiec@cloudius-systems.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A struct member variable is set to the same value more than once
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, the hypercall handling routine only considers LME as an indication
to whether the guest uses 32/64-bit mode. This is incosistent with hyperv
hypercalls handling and against the common sense of considering cs.l as well.
This patch uses is_64_bit_mode instead of is_long_mode for that matter. In
addition, the result is masked in respect to the guest execution mode. Last, it
changes kvm_hv_hypercall to use is_64_bit_mode as well to simplify the code.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The rdpmc emulation checks that the counter (ECX) is not higher than 2, without
taking into considerations bits 30:31 role (e.g., bit 30 marks whether the
counter is fixed). The fix uses the pmu information for checking the validity
of the pmu counter.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
was a pretty active cycle for KVM. Changes include:
- a lot of s390 changes: optimizations, support for migration,
GDB support and more
- ARM changes are pretty small: support for the PSCI 0.2 hypercall
interface on both the guest and the host (the latter acked by Catalin)
- initial POWER8 and little-endian host support
- support for running u-boot on embedded POWER targets
- pretty large changes to MIPS too, completing the userspace interface
and improving the handling of virtualized timer hardware
- for x86, a larger set of changes is scheduled for 3.17. Still,
we have a few emulator bugfixes and support for running nested
fully-virtualized Xen guests (para-virtualized Xen guests have
always worked). And some optimizations too.
The only missing architecture here is ia64. It's not a coincidence
that support for KVM on ia64 is scheduled for removal in 3.17.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=j5Od
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm into next
Pull KVM updates from Paolo Bonzini:
"At over 200 commits, covering almost all supported architectures, this
was a pretty active cycle for KVM. Changes include:
- a lot of s390 changes: optimizations, support for migration, GDB
support and more
- ARM changes are pretty small: support for the PSCI 0.2 hypercall
interface on both the guest and the host (the latter acked by
Catalin)
- initial POWER8 and little-endian host support
- support for running u-boot on embedded POWER targets
- pretty large changes to MIPS too, completing the userspace
interface and improving the handling of virtualized timer hardware
- for x86, a larger set of changes is scheduled for 3.17. Still, we
have a few emulator bugfixes and support for running nested
fully-virtualized Xen guests (para-virtualized Xen guests have
always worked). And some optimizations too.
The only missing architecture here is ia64. It's not a coincidence
that support for KVM on ia64 is scheduled for removal in 3.17"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (203 commits)
KVM: add missing cleanup_srcu_struct
KVM: PPC: Book3S PR: Rework SLB switching code
KVM: PPC: Book3S PR: Use SLB entry 0
KVM: PPC: Book3S HV: Fix machine check delivery to guest
KVM: PPC: Book3S HV: Work around POWER8 performance monitor bugs
KVM: PPC: Book3S HV: Make sure we don't miss dirty pages
KVM: PPC: Book3S HV: Fix dirty map for hugepages
KVM: PPC: Book3S HV: Put huge-page HPTEs in rmap chain for base address
KVM: PPC: Book3S HV: Fix check for running inside guest in global_invalidates()
KVM: PPC: Book3S: Move KVM_REG_PPC_WORT to an unused register number
KVM: PPC: Book3S: Add ONE_REG register names that were missed
KVM: PPC: Add CAP to indicate hcall fixes
KVM: PPC: MPIC: Reset IRQ source private members
KVM: PPC: Graciously fail broken LE hypercalls
PPC: ePAPR: Fix hypercall on LE guest
KVM: PPC: BOOK3S: Remove open coded make_dsisr in alignment handler
KVM: PPC: BOOK3S: Always use the saved DAR value
PPC: KVM: Make NX bit available with magic page
KVM: PPC: Disable NX for old magic page using guests
KVM: PPC: BOOK3S: HV: Add mixed page-size support for guest
...
The PPC fixes are important because they fix breakage that is new in 3.15.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=E2fU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Small fixes for x86, slightly larger fixes for PPC, and a forgotten
s390 patch. The PPC fixes are important because they fix breakage
that is new in 3.15"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: announce irqfd capability
KVM: x86: disable master clock if TSC is reset during suspend
KVM: vmx: disable APIC virtualization in nested guests
KVM guest: Make pv trampoline code executable
KVM: PPC: Book3S: ifdef on CONFIG_KVM_BOOK3S_32_HANDLER for 32bit
KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit
KVM: PPC: Book3S: HV: make _PAGE_NUMA take effect
Updating system_time from the kernel clock once master clock
has been enabled can result in time backwards event, in case
kernel clock frequency is lower than TSC frequency.
Disable master clock in case it is necessary to update it
from the resume path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Regression of 346874c9: PAE is set in long mode, but that does not mean
we have valid PDPTRs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It seems that it's easy to implement the EOI assist
on top of the PV EOI feature: simply convert the
page address to the format expected by PV EOI.
Notes:
-"No EOI required" is set only if interrupt injected
is edge triggered; this is true because level interrupts are going
through IOAPIC which disables PV EOI.
In any case, if guest triggers EOI the bit will get cleared on exit.
-For migration, set of HV_X64_MSR_APIC_ASSIST_PAGE sets
KVM_PV_EOI_EN internally, so restoring HV_X64_MSR_APIC_ASSIST_PAGE
seems sufficient
In any case, bit is cleared on exit so worst case it's never re-enabled
-no handling of PV EOI data is performed at HV_X64_MSR_EOI write;
HV_X64_MSR_EOI is a separate optimization - it's an X2APIC
replacement that lets you do EOI with an MSR and not IO.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As requested by Linus add explicit __visible to the asmlinkage users.
This marks all functions visible to assembler.
Tree sweep for arch/x86/*
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1398984278-29319-3-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch moves the 'kvm_pio' tracepoint to emulator_pio_in_emulated()
and emulator_pio_out_emulated(), and it adds an argument (a pointer to
the 'pio_data'). A single 8-bit or 16-bit or 32-bit data item is fetched
from 'pio_data' (depending on 'size'), and the value is included in the
trace record ('val'). If 'count' is greater than one, this is indicated
by the string "(...)" in the trace output.
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now we can flush all the TLBs out of the mmu lock without TLB corruption when
write-proect the sptes, it is because:
- we have marked large sptes readonly instead of dropping them that means we
just change the spte from writable to readonly so that we only need to care
the case of changing spte from present to present (changing the spte from
present to nonpresent will flush all the TLBs immediately), in other words,
the only case we need to care is mmu_spte_update()
- in mmu_spte_update(), we haved checked
SPTE_HOST_WRITEABLE | PTE_MMU_WRITEABLE instead of PT_WRITABLE_MASK, that
means it does not depend on PT_WRITABLE_MASK anymore
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently, kvm zaps the large spte if write-protected is needed, the later
read can fault on that spte. Actually, we can make the large spte readonly
instead of making them un-present, the page fault caused by read access can
be avoided
The idea is from Avi:
| As I mentioned before, write-protecting a large spte is a good idea,
| since it moves some work from protect-time to fault-time, so it reduces
| jitter. This removes the need for the return value.
This version has fixed the issue reported in 6b73a9606, the reason of that
issue is that fast_page_fault() directly sets the readonly large spte to
writable but only dirty the first page into the dirty-bitmap that means
other pages are missed. Fixed it by only the normal sptes (on the
PT_PAGE_TABLE_LEVEL level) can be fast fixed
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If EFER.LMA is off, cs.l does not determine execution mode.
Currently, the emulation engine assumes differently.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
According to Intel specifications, PAE and non-PAE does not have any reserved
bits. In long-mode, regardless to PCIDE, only the high bits (above the
physical address) are reserved.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
It is sometimes benefitial to ignore IO size, and only match on address.
In hindsight this would have been a better default than matching length
when KVM_IOEVENTFD_FLAG_DATAMATCH is not set, In particular, this kind
of access can be optimized on VMX: there no need to do page lookups.
This can currently be done with many ioeventfds but in a suboptimal way.
However we can't change kernel/userspace ABI without risk of breaking
some applications.
Use len = 0 to mean "ignore length for matching" in a more optimal way.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Pull KVM fixes from Marcelo Tosatti:
- Fix for guest triggerable BUG_ON (CVE-2014-0155)
- CR4.SMAP support
- Spurious WARN_ON() fix
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: remove WARN_ON from get_kernel_ns()
KVM: Rename variable smep to cr4_smep
KVM: expose SMAP feature to guest
KVM: Disable SMAP for guests in EPT realmode and EPT unpaging mode
KVM: Add SMAP support when setting CR4
KVM: Remove SMAP bit from CR4_RESERVED_BITS
KVM: ioapic: try to recover if pending_eoi goes out of range
KVM: ioapic: fix assignment of ioapic->rtc_status.pending_eoi (CVE-2014-0155)
This patch adds SMAP handling logic when setting CR4 for guests
Thanks a lot to Paolo Bonzini for his suggestion to use the branchless
way to detect SMAP violation.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJTQow2AAoJEILEb/54YlRxW4QQAJlYRDUzwFJzJzYhltQYuVR+
4D74XMtvXgoJfg3cwdSWvMKKpJZnA9BVN0f7Hcx9wYmgdexYUuHeZJmMNyc3S2+g
KjKBIsugvgmZhHbbLd6TJ6GBbhGT5JLt9VmSfL9zIkveInU1YHFUUqL/mxdHm4J0
BSGKjk2rN3waRJgmY+xfliFLtQjDKFwJpMuvrgtoUyfas3f4sIV43UNbqdvA/weJ
rzedxXOlKH/id4b56lj/4iIzcoL3mwvJJ7r6n0CEMsKv87z09kqR0O+69Tsq/cgs
j17CsvoJOmZGk3QTeKVMQWBsvk6aPoDu3zK83gLbQMt+qjOpSTbJLz/3HZw4/TrW
ss4nuZne1DLMGS+6hoxYbTP+6Ni//Kn+l/LrHc5jb7m1X3lMO4W2aV3IROtIE1rv
lEP1IG01NU4u9YwkVj1dyhrkSp8tLPul4SrUK8W+oNweOC5crjJV7vJbIPJgmYiM
IZN55wln0yVRtR4TX+rmvN0PixsInE8MeaVCmReApyF9pdzul/StxlBze5BKLSJD
cqo1kNPpsmdxoDucqUpQ/gSvy+IOl2qnlisB5PpV93sk7De6TFDYrGHxjYIW7jMf
StXwdCDDQhzd2Q8Kfpp895A1dbIl8rKtwA6bTU2eX+BfMVFzuMdT44cvosx1+UdQ
sWl//rg76nb13dFjvF+q
=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
kvm_x86_ops is still NULL at this point. Since kvm_init_msr_list
cannot fail, it is safe to initialize it before the call.
Fixes: 93c4adc7af
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the kvm code in x86 by using this latter form of callback registration.
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When doing nested virtualization, we may be able to read BNDCFGS but
still not be allowed to write to GUEST_BNDCFGS in the VMCS. Guard
writes to the field with vmx_mpx_supported(), and similarly hide the
MSR from userspace if the processor does not support the field.
We could work around this with the generic MSR save/load machinery,
but there is only a limited number of MSR save/load slots and it is
not really worthwhile to waste one for a scenario that should not
happen except in the nested virtualization case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
XSAVE support for KVM is already using host_xcr0 & KVM_SUPPORTED_XCR0 as
a "dynamic" version of KVM_SUPPORTED_XCR0.
However, this is not enough because the MPX bits should not be presented
to the guest unless kvm_x86_ops confirms the support. So, replace all
instances of host_xcr0 & KVM_SUPPORTED_XCR0 with a new function
kvm_supported_xcr0() that also has this check.
Note that here:
if (xstate_bv & ~KVM_SUPPORTED_XCR0)
return -EINVAL;
if (xstate_bv & ~host_cr0)
return -EINVAL;
the code is equivalent to
if ((xstate_bv & ~KVM_SUPPORTED_XCR0) ||
(xstate_bv & ~host_cr0)
return -EINVAL;
i.e. "xstate_bv & (~KVM_SUPPORTED_XCR0 | ~host_cr0)" which is in turn
equal to "xstate_bv & ~(KVM_SUPPORTED_XCR0 & host_cr0)". So we should
also use the new function there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both QEMU and KVM have already accumulated a significant number of
optimizations based on the hard-coded assumption that ioapic polarity
will always use the ActiveHigh convention, where the logical and
physical states of level-triggered irq lines always match (i.e.,
active(asserted) == high == 1, inactive == low == 0). QEMU guests
are expected to follow directions given via ACPI and configure the
ioapic with polarity 0 (ActiveHigh). However, even when misbehaving
guests (e.g. OS X <= 10.9) set the ioapic polarity to 1 (ActiveLow),
QEMU will still use the ActiveHigh signaling convention when
interfacing with KVM.
This patch modifies KVM to completely ignore ioapic polarity as set by
the guest OS, enabling misbehaving guests to work alongside those which
comply with the ActiveHigh polarity specified by QEMU's ACPI tables.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gabriel L. Somlo <somlo@cmu.edu>
[Move documentation to KVM_IRQ_LINE, add ia64. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When not running in guest-debug mode, the guest controls the debug
registers and having to take an exit for each DR access is a waste
of time. If the guest gets into a state where each context switch
causes DR to be saved and restored, this can take away as much as 40%
of the execution time from the guest.
After this patch, VMX- and SVM-specific code can set a flag in
switch_db_regs, telling vcpu_enter_guest that on the next exit the debug
registers might be dirty and need to be reloaded (syncing will be taken
care of by a new callback in kvm_x86_ops). This flag can be set on the
first access to a debug registers, so that multiple accesses to the
debug registers only cause one vmexit.
Note that since the guest will be able to read debug registers and
enable breakpoints in DR7, we need to ensure that they are synchronized
on entry to the guest---including DR6 that was not synced before.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's no longer possible to enter enable_irq_window in guest mode when
L1 intercepts external interrupts and we are entering L2. This is now
caught in vcpu_enter_guest. So we can remove the check from the VMX
version of enable_irq_window, thus the need to return an error code from
both enable_irq_window and enable_nmi_window.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the check for leaving L2 on pending and intercepted IRQs or NMIs
from the *_allowed handler into a dedicated callback. Invoke this
callback at the relevant points before KVM checks if IRQs/NMIs can be
injected. The callback has the task to switch from L2 to L1 if needed
and inject the proper vmexit events.
The rework fixes L2 wakeups from HLT and provides the foundation for
preemption timer emulation.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
commit 0061d53daf introduced a mechanism to execute a global clock
update for a vm. We can apply this periodically in order to propagate
host NTP corrections. Also, if all vcpus of a vm are pinned, then
without an additional trigger, no guest NTP corrections can propagate
either, as the current trigger is only vcpu cpu migration.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When we update a vcpu's local clock it may pick up an NTP correction.
We can't wait an indeterminate amount of time for other vcpus to pick
up that correction, so commit 0061d53daf introduced a global clock
update. However, we can't request a global clock update on every vcpu
load either (which is what happens if the tsc is marked as unstable).
The solution is to rate-limit the global clock updates. Marcelo
calculated that we should delay the global clock updates no more
than 0.1s as follows:
Assume an NTP correction c is applied to one vcpu, but not the other,
then in n seconds the delta of the vcpu system_timestamps will be
c * n. If we assume a correction of 500ppm (worst-case), then the two
vcpus will diverge 50us in 0.1s, which is a considerable amount.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The problem occurs when the guest performs a pusha with the stack
address pointing to an mmio address (or an invalid guest physical
address) to start with, but then extending into an ordinary guest
physical address. When doing repeated emulated pushes
emulator_read_write sets mmio_needed to 1 on the first one. On a
later push when the stack points to regular memory,
mmio_nr_fragments is set to 0, but mmio_is_needed is not set to 0.
As a result, KVM exits to userspace, and then returns to
complete_emulated_mmio. In complete_emulated_mmio
vcpu->mmio_cur_fragment is incremented. The termination condition of
vcpu->mmio_cur_fragment == vcpu->mmio_nr_fragments is never achieved.
The code bounces back and fourth to userspace incrementing
mmio_cur_fragment past it's buffer. If the guest does nothing else it
eventually leads to a a crash on a memcpy from invalid memory address.
However if a guest code can cause the vm to be destroyed in another
vcpu with excellent timing, then kvm_clear_async_pf_completion_queue
can be used by the guest to control the data that's pointed to by the
call to cancel_work_item, which can be used to gain execution.
Fixes: f78146b0f9
Signed-off-by: Andrew Honig <ahonig@google.com>
Cc: stable@vger.kernel.org (3.5+)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to scan the entire VCPU array.
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
emulator_cmpxchg_emulated writes to guest memory, therefore it should
update the dirty bitmap accordingly.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
From 5d5a80cd172ea6fb51786369bcc23356b1e9e956 Mon Sep 17 00:00:00 2001
From: Liu Jinsong <jinsong.liu@intel.com>
Date: Mon, 24 Feb 2014 18:11:55 +0800
Subject: [PATCH v5 2/3] KVM: x86: add MSR_IA32_BNDCFGS to msrs_to_save
Add MSR_IA32_BNDCFGS to msrs_to_save, and corresponding logic
to kvm_get/set_msr().
Signed-off-by: Liu Jinsong <jinsong.liu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
From 00c920c96127d20d4c3bb790082700ae375c39a0 Mon Sep 17 00:00:00 2001
From: Liu Jinsong <jinsong.liu@intel.com>
Date: Fri, 21 Feb 2014 23:47:18 +0800
Subject: [PATCH] KVM: x86: Fix xsave cpuid exposing bug
EBX of cpuid(0xD, 0) is dynamic per XCR0 features enable/disable.
Bit 63 of XCR0 is reserved for future expansion.
Signed-off-by: Liu Jinsong <jinsong.liu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check for invalid state transitions on guest-initiated updates of
MSR_IA32_APICBASE. This address both enabling of the x2APIC when it is
not supported and all invalid transitions as described in SDM section
10.12.5. It also checks that no reserved bit is set in APICBASE by the
guest.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
[Use cpuid_maxphyaddr instead of guest_cpuid_get_phys_bits. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nothing major here, just bugfixes all over the place. The most
interesting part is the ARM guys' virtualized interrupt controller
overhaul, which lets userspace get/set the state and thus enables
migration of ARM VMs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=8sYU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"First round of KVM updates for 3.14; PPC parts will come next week.
Nothing major here, just bugfixes all over the place. The most
interesting part is the ARM guys' virtualized interrupt controller
overhaul, which lets userspace get/set the state and thus enables
migration of ARM VMs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (67 commits)
kvm: make KVM_MMU_AUDIT help text more readable
KVM: s390: Fix memory access error detection
KVM: nVMX: Update guest activity state field on L2 exits
KVM: nVMX: Fix nested_run_pending on activity state HLT
KVM: nVMX: Clean up handling of VMX-related MSRs
KVM: nVMX: Add tracepoints for nested_vmexit and nested_vmexit_inject
KVM: nVMX: Pass vmexit parameters to nested_vmx_vmexit
KVM: nVMX: Leave VMX mode on clearing of feature control MSR
KVM: VMX: Fix DR6 update on #DB exception
KVM: SVM: Fix reading of DR6
KVM: x86: Sync DR7 on KVM_SET_DEBUGREGS
add support for Hyper-V reference time counter
KVM: remove useless write to vcpu->hv_clock.tsc_timestamp
KVM: x86: fix tsc catchup issue with tsc scaling
KVM: x86: limit PIT timer frequency
KVM: x86: handle invalid root_hpa everywhere
kvm: Provide kvm_vcpu_eligible_for_directed_yield() stub
kvm: vfio: silence GCC warning
KVM: ARM: Remove duplicate include
arm/arm64: KVM: relax the requirements of VMA alignment for THP
...
In contrast to VMX, SVM dose not automatically transfer DR6 into the
VCPU's arch.dr6. So if we face a DR6 read, we must consult a new vendor
hook to obtain the current value. And as SVM now picks the DR6 state
from its VMCB, we also need a set callback in order to write updates of
DR6 back.
Fixes a regression of 020df0794f.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Whenever we change arch.dr7, we also have to call kvm_update_dr7. In
case guest debugging is off, this will synchronize the new state into
hardware.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini