Most reset methods are of the form "pci_*_reset(dev, probe)". pcie_flr()
was an exception because it relied on a separate pcie_has_flr() function
instead of taking a "probe" argument.
Add "pcie_reset_flr(dev, probe)" to follow the convention. Remove
pcie_has_flr().
Some pcie_flr() callers that did not use pcie_has_flr() remain.
[bhelgaas: commit log, rework pcie_reset_flr() to use dev->devcap directly]
Link: https://lore.kernel.org/r/20210817180500.1253-3-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
- Ignore pciehp Link Down/Up caused by DPC so device remains bound to
driver (Lukas Wunner)
- Declare global cpci_debug in header file (Krzysztof Wilczyński)
* pci/hotplug:
PCI: cpcihp: Declare cpci_debug in header file
PCI: pciehp: Ignore Link Down/Up caused by DPC
Downstream Port Containment (PCIe r5.0, sec. 6.2.10) disables the link upon
an error and attempts to re-enable it when instructed by the DPC driver.
A slot which is both DPC- and hotplug-capable is currently powered off by
pciehp once DPC is triggered (due to the link change) and powered back up
on successful recovery. That's undesirable, the slot should remain powered
so the hotplugged device remains bound to its driver. DPC notifies the
driver of the error and of successful recovery in pcie_do_recovery() and
the driver may then restore the device to working state.
Moreover, Sinan points out that turning off slot power by pciehp may foil
recovery by DPC: Power off/on is a cold reset concurrently to DPC's warm
reset. Sathyanarayanan reports extended delays or failure in link
retraining by DPC if pciehp brings down the slot.
Fix by detecting whether a Link Down event is caused by DPC and awaiting
recovery if so. On successful recovery, ignore both the Link Down and the
subsequent Link Up event.
Afterwards, check whether the link is down to detect surprise-removal or
another DPC event immediately after DPC recovery. Ensure that the
corresponding DLLSC event is not ignored by synthesizing it and invoking
irq_wake_thread() to trigger a re-run of pciehp_ist().
The IRQ threads of the hotplug and DPC drivers, pciehp_ist() and
dpc_handler(), race against each other. If pciehp is faster than DPC, it
will wait until DPC recovery completes.
Recovery consists of two steps: The first step (waiting for link
disablement) is recognizable by pciehp through a set DPC Trigger Status
bit. The second step (waiting for link retraining) is recognizable through
a newly introduced PCI_DPC_RECOVERING flag.
If DPC is faster than pciehp, neither of the two flags will be set and
pciehp may glean the recovery status from the new PCI_DPC_RECOVERED flag.
The flag is zero if DPC didn't occur at all, hence DLLSC events are not
ignored by default.
pciehp waits up to 4 seconds before assuming that DPC recovery failed and
bringing down the slot. This timeout is not taken from the spec (it
doesn't mandate one) but based on a report from Yicong Yang that DPC may
take a bit more than 3 seconds on HiSilicon's Kunpeng platform.
The timeout is necessary because the DPC Trigger Status bit may never
clear: On Root Ports which support RP Extensions for DPC, the DPC driver
polls the DPC RP Busy bit for up to 1 second before giving up on DPC
recovery. Without the timeout, pciehp would then wait indefinitely for DPC
to complete.
This commit draws inspiration from previous attempts to synchronize DPC
with pciehp:
By Sinan Kaya, August 2018:
https://lore.kernel.org/linux-pci/20180818065126.77912-1-okaya@kernel.org/
By Ethan Zhao, October 2020:
https://lore.kernel.org/linux-pci/20201007113158.48933-1-haifeng.zhao@intel.com/
By Kuppuswamy Sathyanarayanan, March 2021:
https://lore.kernel.org/linux-pci/59cb30f5e5ac6d65427ceaadf1012b2ba8dbf66c.1615606143.git.sathyanarayanan.kuppuswamy@linux.intel.com/
Link: https://lore.kernel.org/r/0be565d97438fe2a6d57354b3aa4e8626952a00b.1619857124.git.lukas@wunner.de
Reported-by: Sinan Kaya <okaya@kernel.org>
Reported-by: Ethan Zhao <haifeng.zhao@intel.com>
Reported-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>
The sysfs_emit() and sysfs_emit_at() functions were introduced to make
it less ambiguous which function is preferred when writing to the output
buffer in a device attribute's "show" callback [1].
Convert the PCI sysfs object "show" functions from sprintf(), snprintf()
and scnprintf() to sysfs_emit() and sysfs_emit_at() accordingly, as the
latter is aware of the PAGE_SIZE buffer and correctly returns the number
of bytes written into the buffer.
No functional change intended.
[1] Documentation/filesystems/sysfs.rst
Related commit: ad025f8e46 ("PCI/sysfs: Use sysfs_emit() and
sysfs_emit_at() in "show" functions").
Link: https://lore.kernel.org/r/20210603000112.703037-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
We use format domain🚌slot.function when printing PCI device. Use
consistent format in AER messages.
[bhelgaas: also drop "AER recover:" prefix since we already have an "AER:"
prefix from pr_fmt()]
Link: https://lore.kernel.org/r/1617015721-51701-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
rcec_assoc_rciep() used "rciep->devfn" (a single byte encoding both the
device and function number) as the device number to check whether the
corresponding bit was set in the RCEC's Association Bitmap for RCiEPs.
But per PCIe r5.0, sec 7.9.10.2, "Association Bitmap for RCiEPs", the
32-bit bitmap contains one bit per device. That bit applies to all
functions of the device.
Fix rcec_assoc_rciep() to convert the value of "rciep->devfn" to a device
number to ensure that RCiEP devices are correctly associated with the RCEC.
Reported-and-tested-by: Wen Jin <wen.jin@intel.com>
Fixes: 507b460f81 ("PCI/ERR: Add pcie_link_rcec() to associate RCiEPs")
Link: https://lore.kernel.org/r/20210222011717.43266-1-qiuxu.zhuo@intel.com
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sean V Kelley <sean.v.kelley@intel.com>
-----BEGIN PGP SIGNATURE-----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=GXL5
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Remove unnecessary locking around _OSC (Bjorn Helgaas)
- Clarify message about _OSC failure (Bjorn Helgaas)
- Remove notification of PCIe bandwidth changes (Bjorn Helgaas)
- Tidy checking of syscall user config accessors (Heiner Kallweit)
Resource management:
- Decline to resize resources if boot config must be preserved (Ard
Biesheuvel)
- Fix pci_register_io_range() memory leak (Geert Uytterhoeven)
Error handling (Keith Busch):
- Clear error status from the correct device
- Retain error recovery status so drivers can use it after reset
- Log the type of Port (Root or Switch Downstream) that we reset
- Always request a reset for Downstream Ports in frozen state
Endpoint framework and NTB (Kishon Vijay Abraham I):
- Make *_get_first_free_bar() take into account 64 bit BAR
- Add helper API to get the 'next' unreserved BAR
- Make *_free_bar() return error codes on failure
- Remove unused pci_epf_match_device()
- Add support to associate secondary EPC with EPF
- Add support in configfs to associate two EPCs with EPF
- Add pci_epc_ops to map MSI IRQ
- Add pci_epf_ops to expose function-specific attrs
- Allow user to create sub-directory of 'EPF Device' directory
- Implement ->msi_map_irq() ops for cadence
- Configure LM_EP_FUNC_CFG based on epc->function_num_map for cadence
- Add EP function driver to provide NTB functionality
- Add support for EPF PCI Non-Transparent Bridge
- Add specification for PCI NTB function device
- Add PCI endpoint NTB function user guide
- Add configfs binding documentation for pci-ntb endpoint function
Broadcom STB PCIe controller driver:
- Add support for BCM4908 and external PERST# signal controller
(Rafał Miłecki)
Cadence PCIe controller driver:
- Retrain Link to work around Gen2 training defect (Nadeem Athani)
- Fix merge botch in cdns_pcie_host_map_dma_ranges() (Krzysztof
Wilczyński)
Freescale Layerscape PCIe controller driver:
- Add LX2160A rev2 EP mode support (Hou Zhiqiang)
- Convert to builtin_platform_driver() (Michael Walle)
MediaTek PCIe controller driver:
- Fix OF node reference leak (Krzysztof Wilczyński)
Microchip PolarFlare PCIe controller driver:
- Add Microchip PolarFire PCIe controller driver (Daire McNamara)
Qualcomm PCIe controller driver:
- Use PHY_REFCLK_USE_PAD only for ipq8064 (Ansuel Smith)
- Add support for ddrss_sf_tbu clock for sm8250 (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Drop PCIE_RCAR config option (Lad Prabhakar)
- Always allocate MSI addresses in 32bit space (Marek Vasut)
Rockchip PCIe controller driver:
- Add FriendlyARM NanoPi M4B DT binding (Chen-Yu Tsai)
- Make 'ep-gpios' DT property optional (Chen-Yu Tsai)
Synopsys DesignWare PCIe controller driver:
- Work around ECRC configuration hardware defect (Vidya Sagar)
- Drop support for config space in DT 'ranges' (Rob Herring)
- Change size to u64 for EP outbound iATU (Shradha Todi)
- Add upper limit address for outbound iATU (Shradha Todi)
- Make dw_pcie ops optional (Jisheng Zhang)
- Remove unnecessary dw_pcie_ops from al driver (Jisheng Zhang)
Xilinx Versal CPM PCIe controller driver:
- Fix OF node reference leak (Pan Bian)
Miscellaneous:
- Remove tango host controller driver (Arnd Bergmann)
- Remove IRQ handler & data together (altera-msi, brcmstb, dwc)
(Martin Kaiser)
- Fix xgene-msi race in installing chained IRQ handler (Martin
Kaiser)
- Apply CONFIG_PCI_DEBUG to entire drivers/pci hierarchy (Junhao He)
- Fix pci-bridge-emul array overruns (Russell King)
- Remove obsolete uses of WARN_ON(in_interrupt()) (Sebastian Andrzej
Siewior)"
* tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (69 commits)
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
PCI: al: Remove useless dw_pcie_ops
PCI: dwc: Don't assume the ops in dw_pcie always exist
PCI: dwc: Add upper limit address for outbound iATU
PCI: dwc: Change size to u64 for EP outbound iATU
PCI: dwc: Drop support for config space in 'ranges'
PCI: layerscape: Convert to builtin_platform_driver()
PCI: layerscape: Add LX2160A rev2 EP mode support
dt-bindings: PCI: layerscape: Add LX2160A rev2 compatible strings
PCI: dwc: Work around ECRC configuration issue
PCI/portdrv: Report reset for frozen channel
PCI/AER: Specify the type of Port that was reset
PCI/ERR: Retain status from error notification
PCI/AER: Clear AER status from Root Port when resetting Downstream Port
PCI/ERR: Clear status of the reporting device
dt-bindings: arm: rockchip: Add FriendlyARM NanoPi M4B
PCI: rockchip: Make 'ep-gpios' DT property optional
Documentation: PCI: Add PCI endpoint NTB function user guide
...
The PCI error recovery always resets the link for a frozen state, so the
port driver should return that a reset is required for its result. This
will get the .slot_reset() callback invoked, which is necessary to
restore the port's config space. Without this, the driver had been
relying on downstream drivers to return this status.
Link: https://lore.kernel.org/r/20210104230300.1277180-6-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
The AER driver may be called upon to reset either a Downstream or a Root
Port. Check which type it is to properly identify it when logging that
the reset occurred.
Link: https://lore.kernel.org/r/20210104230300.1277180-5-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
Overwriting the frozen detected status with the result of the link reset
loses the NEED_RESET result that drivers are depending on for error
handling to report the .slot_reset() callback. Retain this status so
that subsequent error handling has the correct flow.
Link: https://lore.kernel.org/r/20210104230300.1277180-4-kbusch@kernel.org
Reported-by: Hinko Kocevar <hinko.kocevar@ess.eu>
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean V Kelley <sean.v.kelley@intel.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
The pci_dev parameter given to aer_root_reset() may be a Downstream Port
rather than the Root Port. Get the Root Port from the provided device in
order to clear the root's AER status.
Link: https://lore.kernel.org/r/20210104230300.1277180-3-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean V Kelley <sean.v.kelley@intel.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
Error handling operates on the first Downstream Port above the detected
error, but the error may have been reported by a downstream device.
Clear the AER status of the device that reported the error rather than
the first Downstream Port.
Link: https://lore.kernel.org/r/20210104230300.1277180-2-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean V Kelley <sean.v.kelley@intel.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
The PCIe Bandwidth Change Notification feature logs messages when the link
bandwidth changes. Some users have reported that these messages occur
often enough to significantly reduce NVMe performance. GPUs also seem to
generate these messages.
We don't know why the link bandwidth changes, but in the reported cases
there's no indication that it's caused by hardware failures.
Remove the bandwidth change notifications for now. Hopefully we can add
this back when we have a better understanding of why this happens and how
we can make the messages useful instead of overwhelming.
Link: https://lore.kernel.org/r/20200115221008.GA191037@google.com/
Link: https://lore.kernel.org/r/155605909349.3575.13433421148215616375.stgit@gimli.home/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206197
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Save/restore Precision Time Measurement Capability for suspend/resume
(David E. Box)
- Disable PTM during suspend to save power (David E. Box)
* pci/ptm:
PCI: Disable PTM during suspend to save power
PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume
- Stop writing AER Capability when we don't own it (Sean V Kelley)
- Bind RCEC devices to the Port driver (Qiuxu Zhuo)
- Cache the RCEC RA Capability offset (Sean V Kelley)
- Add pci_walk_bridge() (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs with RCECs (Sean V Kelley)
- Recover from RCiEP AER errors (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
* pci/err:
PCI/AER: Add RCEC AER error injection support
PCI/PME: Add pcie_walk_rcec() to RCEC PME handling
PCI/AER: Add pcie_walk_rcec() to RCEC AER handling
PCI/ERR: Recover from RCiEP AER errors
PCI/ERR: Add pcie_link_rcec() to associate RCiEPs
PCI/ERR: Recover from RCEC AER errors
PCI/ERR: Clear AER status only when we control AER
PCI/ERR: Add pci_walk_bridge() to pcie_do_recovery()
PCI/ERR: Avoid negated conditional for clarity
PCI/ERR: Use "bridge" for clarity in pcie_do_recovery()
PCI/ERR: Simplify by computing pci_pcie_type() once
PCI/ERR: Simplify by using pci_upstream_bridge()
PCI/ERR: Rename reset_link() to reset_subordinates()
PCI/ERR: Cache RCEC EA Capability offset in pci_init_capabilities()
PCI/ERR: Bind RCEC devices to the Root Port driver
PCI/AER: Write AER Capability only when we control it
There are systems (for example, Intel based mobile platforms since Coffee
Lake) where the power drawn while suspended can be significantly reduced by
disabling Precision Time Measurement (PTM) on PCIe root ports as this
allows the port to enter a lower-power PM state and the SoC to reach a
lower-power idle state. To save this power, disable the PTM feature on root
ports during pci_prepare_to_sleep() and pci_finish_runtime_suspend(). The
feature will be returned to its previous state during restore and error
recovery.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=209361
Link: https://lore.kernel.org/r/20201207223951.19667-2-david.e.box@linux.intel.com
Reported-by: Len Brown <len.brown@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI subsystem does not currently save and restore the configuration
space for the Precision Time Measurement (PTM) Extended Capability leading
to the possibility of the feature returning disabled on S3 resume. This
has been observed on Intel Coffee Lake desktops. Add save/restore of the
PTM control register. This saves the PTM Enable, Root Select, and Effective
Granularity bits.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20201207223951.19667-1-david.e.box@linux.intel.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Root Complex Event Collectors (RCEC) appear as peers to Root Ports and may
also have the AER capability.
Add RCEC support to the AER error injection driver.
Co-developed-by: Sean V Kelley <sean.v.kelley@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-16-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Root Complex Event Collectors (RCEC) appear as peers of Root Ports and also
have the PME capability. As with AER, there is a need to be able to walk
the RCiEPs associated with their RCEC for purposes of acting upon them with
callbacks.
Add RCEC support through the use of pcie_walk_rcec() to the current PME
service driver and attach the PME service driver to the RCEC device.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-15-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Root Complex Event Collectors (RCEC) appear as peers to Root Ports and also
have the AER capability. In addition, actions need to be taken for
associated RCiEPs. In such cases the RCECs will need to be walked in order
to find and act upon their respective RCiEPs.
Extend the existing ability to link the RCECs with a walking function
pcie_walk_rcec(). Add RCEC support to the current AER service driver and
attach the AER service driver to the RCEC device.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-14-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Add support for handling AER errors detected by Root Complex Integrated
Endpoints (RCiEPs). These errors are signaled to software natively via a
Root Complex Event Collector (RCEC) or non-natively via ACPI APEI if the
platform retains control of AER or uses a non-standard RCEC-like device.
When recovering from RCiEP errors, the Root Error Command and Status
registers are in the AER Capability of an associated RCEC (if any), not in
a Root Port. In the non-native case, the platform is responsible for those
registers and we can't touch them.
[bhelgaas: commit log, etc]
Co-developed-by: Sean V Kelley <sean.v.kelley@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-13-sean.v.kelley@intel.com
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A Root Complex Event Collector terminates error and PME messages from
associated RCiEPs.
Use the RCEC Endpoint Association Extended Capability to identify
associated RCiEPs. Link the associated RCiEPs as the RCECs are enumerated.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-12-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A Root Complex Event Collector (RCEC) collects and signals AER errors that
were detected by Root Complex Integrated Endpoints (RCiEPs), but it may
also signal errors it detects itself. This is analogous to errors detected
and signaled by a Root Port.
Update the AER service driver to claim RCECs in addition to Root Ports.
Add support for handling RCEC-detected AER errors. This does not
include handling RCiEP-detected errors that are signaled by the RCEC.
Note that we expect these errors only from the native AER and APEI paths,
not from DPC or EDR.
[bhelgaas: split from combined RCEC/RCiEP patch, commit log]
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In some cases a bridge may not exist as the hardware controlling may be
handled only by firmware and so is not visible to the OS. This scenario is
also possible in future use cases involving non-native use of RCECs by
firmware. In this scenario, we expect the platform to retain control of the
bridge and to clear error status itself.
Clear error status only when the OS has native control of AER.
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Consolidate subordinate bus checks with pci_walk_bus() into
pci_walk_bridge() for walking below potentially AER affected bridges.
Link: https://lore.kernel.org/r/20201121001036.8560-10-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reverse the sense of the Root Port/Downstream Port conditional for clarity.
No functional change intended.
Link: https://lore.kernel.org/r/20201121001036.8560-9-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pcie_do_recovery() may be called with "dev" being either a bridge (Root
Port or Switch Downstream Port) or an Endpoint. The bulk of the function
deals with the bridge, so if we start with an Endpoint, we reset "dev" to
be the bridge leading to it.
For clarity, replace "dev" in the body of the function with "bridge". No
functional change intended.
Link: https://lore.kernel.org/r/20201121001036.8560-8-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of calling pci_pcie_type(dev) twice, call it once and save the
result. No functional change intended.
Link: https://lore.kernel.org/r/20201121001036.8560-7-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use pci_upstream_bridge() in place of dev->bus->self. No functional change
intended.
Link: https://lore.kernel.org/r/20201121001036.8560-6-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
reset_link() appears to be misnamed. The point is to reset any devices
below a given bridge, so rename it to reset_subordinates() to make it clear
that we are passing a bridge with the intent to reset the devices below it.
Link: https://lore.kernel.org/r/20201121001036.8560-5-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extend support for Root Complex Event Collectors by decoding and caching
the RCEC Endpoint Association Extended Capabilities when enumerating. Use
that cached information for later error source reporting. See PCIe r5.0,
sec 7.9.10.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-4-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If a Root Complex Integrated Endpoint (RCiEP) is implemented, it may signal
errors through a Root Complex Event Collector (RCEC). Each RCiEP must be
associated with no more than one RCEC.
For an RCEC (which is technically not a Bridge), error messages "received"
from associated RCiEPs must be enabled for "transmission" in order to cause
a System Error via the Root Control register or (when the Advanced Error
Reporting Capability is present) reporting via the Root Error Command
register and logging in the Root Error Status register and Error Source
Identification register.
Given the commonality with Root Ports and the need to also support AER and
PME services for RCECs, extend the Root Port driver to support RCEC devices
by adding the RCEC Class ID to the driver structure.
Co-developed-by: Sean V Kelley <sean.v.kelley@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-3-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
If an OS has not been granted AER control via _OSC, it should not make
changes to PCI_ERR_ROOT_COMMAND and PCI_ERR_ROOT_STATUS related registers.
Per section 4.5.1 of the System Firmware Intermediary (SFI) _OSC and DPC
Updates ECN [1], this bit also covers these aspects of the PCI Express
Advanced Error Reporting. Based on the above and earlier discussion [2],
make the following changes:
Add a check for the native case (i.e., AER control via _OSC)
Note that the previous "clear, reset, enable" order suggests that the reset
might cause errors that we should ignore. After this commit, those errors
(if any) will remain logged in the PCI_ERR_ROOT_STATUS register.
[1] System Firmware Intermediary (SFI) _OSC and DPC Updates ECN, Feb 24,
2020, affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/14076
[2] https://lore.kernel.org/linux-pci/20201020162820.GA370938@bjorn-Precision-5520/
Link: https://lore.kernel.org/r/20201121001036.8560-2-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously ASPM L1 Substates control registers (CTL1 and CTL2) weren't
saved and restored during suspend/resume leading to L1 Substates
configuration being lost post-resume.
Save the L1 Substates control registers so that the configuration is
retained post-resume.
Link: https://lore.kernel.org/r/20201024190442.871-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Remove unnecessary #includes (Gustavo Pimentel)
- Fix intel_mid_pci.c build error when !CONFIG_ACPI (Randy Dunlap)
- Use scnprintf(), not snprintf(), in sysfs "show" functions (Krzysztof
Wilczyński)
- Simplify pci-pf-stub by using module_pci_driver() (Liu Shixin)
- Print IRQ used by Link Bandwidth Notification (Dongdong Liu)
- Update sysfs mmap-related #ifdef comments (Clint Sbisa)
- Simplify pci_dev_reset_slot_function() (Lukas Wunner)
- Use "NULL" instead of "0" to fix sparse warnings (Gustavo Pimentel)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Drop double zeroing for P2PDMA sg_init_table() (Julia Lawall)
* pci/misc:
PCI: v3-semi: Remove unneeded break
PCI/P2PDMA: Drop double zeroing for sg_init_table()
PCI: Simplify bool comparisons
PCI: endpoint: Use "NULL" instead of "0" as a NULL pointer
PCI: Simplify pci_dev_reset_slot_function()
PCI: Update mmap-related #ifdef comments
PCI/LINK: Print IRQ number used by port
PCI/IOV: Simplify pci-pf-stub with module_pci_driver()
PCI: Use scnprintf(), not snprintf(), in sysfs "show" functions
x86/PCI: Fix intel_mid_pci.c build error when ACPI is not enabled
PCI: Remove unnecessary header includes
- Use for_each_child_of_node() and for_each_node_by_name() instead of
open-coding them (Qinglang Miao)
- Reduce pciehp noisiness on hot removal (Lukas Wunner)
- Remove unused assignment in shpchp (Krzysztof Wilczyński)
* pci/hotplug:
PCI: shpchp: Remove unused 'rc' assignment
PCI: pciehp: Reduce noisiness on hot removal
PCI: rpadlpar: Use for_each_child_of_node() and for_each_node_by_name()
Previously we computed L1.2 parameters in the enumeration path, saved them
in struct pcie_link_state.l1ss, and programmed them into the devices
whenever we enabled or disabled L1.2 on the link. But these parameters are
constant and don't need to be updated when enabling/disabling L1.2.
Compute and program the L1.2 parameters once during enumeration and remove
the struct pcie_link_state.l1ss member. No functional change intended.
[bhelgaas: rework to program L1.2 parameters during enumeration]
Link: https://lore.kernel.org/r/20201015193039.12585-13-helgaas@kernel.org
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we stored the L1SS Capabilities value in the struct
aspm_register_info.
We only need this information in one place, so read it there and remove
struct aspm_register_info completely, since it's now empty. No functional
change intended.
[bhelgaas: split up, don't cache l1ss_cap in pci_dev]
Link: https://lore.kernel.org/r/20201015193039.12585-12-helgaas@kernel.org
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aspm_calc_l1ss_info() needs only the L1SS Capabilities. It doesn't need
anything else from struct aspm_register_info, so pass only the Capabilities
value. No functional change intended.
Link: https://lore.kernel.org/r/20201015193039.12585-11-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we stored the L1SS Control 1 register in the struct
aspm_register_info.
We only need this information in one place, so read it there and remove it
from struct aspm_register_info. No functional change intended.
[bhelgaas: split ctl1/ctl2]
Link: https://lore.kernel.org/r/20201015193039.12585-10-helgaas@kernel.org
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save the L1 Substates Capability pointer in struct pci_dev. Then we don't
have to keep track of it in the struct aspm_register_info and struct
pcie_link_state, which makes the code easier to read. No functional change
intended.
[bhelgaas: split to a separate patch]
Link: https://lore.kernel.org/r/20201015193039.12585-8-helgaas@kernel.org
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we stored L0s and L1 Exit Latency information from the Link
Capabilities register in the struct aspm_register_info.
We only need these latencies when we already have the Link Capabilities
values, so use those directly and remove the latencies from struct
aspm_register_info. No functional change intended.
Link: https://lore.kernel.org/r/20201015193039.12585-7-helgaas@kernel.org
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we stored the "ASPM Control" bits from the Link Control register
in the struct aspm_register_info.
Read PCI_EXP_LNKCTL directly when needed. This means we can use the
PCI_EXP_LNKCTL_ASPM_* bits directly instead of the similar but different
PCIE_LINK_STATE_* bits. No functional change intended.
[bhelgaas: drop get_aspm_enable() and read LNKCTL once directly]
Link: https://lore.kernel.org/r/20201015193039.12585-6-helgaas@kernel.org
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we stored the "ASPM Support" field from the Link Capabilities
register in the struct aspm_register_info.
Read the Link Capabilities directly when needed and remove it from the
struct aspm_register_info. No functional change intended.
[bhelgaas: remove pci_dev cached copy since LNKCAP isn't truly read-only,
add PCI_EXP_LNKCAP_ASPM_L0S & PCI_EXP_LNKCAP_ASPM_L1, check them directly
instead of adding aspm_support()]
Link: https://lore.kernel.org/r/20201015193039.12585-5-helgaas@kernel.org
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Amey Narkhede