The write wait queue is never added to since commit f1175daa5 ("USB:
ti_usb_3410_5052: kill custom closing_wait"). Remove it completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill private write fifo and use the already allocated port write fifo
instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the vendor and product module parameters which were added a long
time ago when we did not have the dynamic sysfs interface to add
new device ids (and which isn't limited to a single new vid/pid pair).
A vid/pid pair can be added dynamically using sysfs, for example:
echo 04dd 1234 >/sys/bus/usb-serial/drivers/safe_serial/new_id
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken "chase" implementation which was supposed to be used to
drain the write buffers at break.
The chase implementation slept on a wait queue which was never woken up
(i.e. no hardware buffers were queried), and thus amounted to nothing
more than polling chars_in_buffer, something which has already been
taken care of by the tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move port initialisation code from open to probe where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill private write fifo and use the already allocated port write fifo
instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the vendor and product module parameters which were added a long
time ago when we did not have the dynamic sysfs interface to add
new device ids (and which isn't limited to a single new vid/pid pair).
A vid/pid pair can be added dynamically using sysfs, for example:
echo 0403 1234 >/sys/bus/usb-serial/drivers/ftdi_sio/new_id
Also fix up the in-code comment that got the sysfs path wrong.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not raise DTR/RTS a second time in set_termios at open -- this has
already been taken care of by the tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use zeroed termios data to determine when to unconditionally
configure the device at open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure set_termios is not called with uninitialised data at open. The
old termios struct is currently not used, but pass NULL instead to avoid
future problems (e.g. stack data leak).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only log the tty_flags in process_read_urb on errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out baud-rate handling from set_termios.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary tests for open and write operations as these are set
to the generic implementations by usb-serial core if left unset by a
subdriver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port drain delay is constant and should be set at port probe rather
than open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 957dacae ("TTY: fix DTR not being dropped on hang up")
dtr_rts is no longer called for uninitialised ports (e.g. after
a disconnect), which removes the need to grab the disconnect mutex.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 31ca020b ("TTY: wake up processes last at hangup") there no
longer any need to check the hupping flag in the generic tiocmiwait
implementation, so remove it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove defensive test from set_termios which is never called with a NULL
tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.
Signed-off-by: Sami Rahman <sami.rahman@mmbresearch.com>
Tested-by: Sami Rahman <sami.rahman@mmbresearch.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.
Signed-off-by: Barry Grussling <barry@grussling.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series
USB ID (0846:0110) to the cp210x driver. Without this, the serial
adapter is not recognized in Linux. Description was obtained from
an Netgear Eng.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are all Gobi1K devices (according to the Windows INF
files) and should be handled by qcserial instead of option. Their
network port is handled by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add product id for Abbott strip port cable for Precision meter which
uses the TI 3410 chip.
Signed-off-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had the limit of 255 USB to serial devices on one system for almost
15 years, with no complaints. But now it's time to move on from these
tiny "baby" systems, and bump the number up to 512, which should last
us a few more years:
"512 is a nice number" -- Tobias Winter
Note, this is still a static value, and uses up tty core memory with
this many tty devices allocated. Converting the driver to use
TTY_DRIVER_DYNAMIC_DEV is the next thing to do in order to remove this
limitation.
Reported-by: Tobias Winter <tobias@linuxdingsda.de>
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the allocation of minor device numbers from a static array to
be dynamic, using the idr interface. This means that you could
potentially get "gaps" in a minor number range for a single USB serial
device with multiple ports, but all should still work properly.
We remove the 'minor' field from the usb_serial structure, as it no
longer makes any sense for it (use the field in the usb_serial_port
structure if you really want to know this number), and take the fact
that we were overloading a number in this field to determine if we had
initialized the minor numbers or not, and just use a flag variable
instead.
Note, we still have the limitation of 255 USB to serial devices in the
system, as that is all we are registering with the TTY layer at this
point in time.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_serial_port structure had the number field, which was the minor
number for the port, which almost no one really cared about. They
really wanted the number of the port within the device, which you had to
subtract from the minor of the parent usb_serial_device structure. To
clean this up, provide the real minor number of the port, and the number
of the port within the serial device separately, as these numbers might
not be related in the future.
Bonus is that this cleans up a lot of logic in the drivers, and saves
lines overall.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
drivers/staging/serqt_usb2/serqt_usb2.c | 21 +++--------
drivers/usb/serial/ark3116.c | 2 -
drivers/usb/serial/bus.c | 6 +--
drivers/usb/serial/console.c | 2 -
drivers/usb/serial/cp210x.c | 2 -
drivers/usb/serial/cypress_m8.c | 4 +-
drivers/usb/serial/digi_acceleport.c | 6 ---
drivers/usb/serial/f81232.c | 5 +-
drivers/usb/serial/garmin_gps.c | 6 +--
drivers/usb/serial/io_edgeport.c | 58 ++++++++++++--------------------
drivers/usb/serial/io_ti.c | 21 ++++-------
drivers/usb/serial/keyspan.c | 29 +++++++---------
drivers/usb/serial/metro-usb.c | 4 +-
drivers/usb/serial/mos7720.c | 37 +++++++++-----------
drivers/usb/serial/mos7840.c | 52 +++++++++-------------------
drivers/usb/serial/opticon.c | 2 -
drivers/usb/serial/pl2303.c | 2 -
drivers/usb/serial/quatech2.c | 7 +--
drivers/usb/serial/sierra.c | 2 -
drivers/usb/serial/ti_usb_3410_5052.c | 10 ++---
drivers/usb/serial/usb-serial.c | 7 ++-
drivers/usb/serial/usb_wwan.c | 2 -
drivers/usb/serial/whiteheat.c | 20 +++++------
include/linux/usb/serial.h | 6 ++-
24 files changed, 133 insertions(+), 180 deletions(-)
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace in the OOM error
path.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 143d9d9616 ("USB: serial: add
tiocmiwait subdriver operation") which made the ioctl operation return
ENODEV rather than ENOIOCTLCMD when a subdriver TIOCMIWAIT
implementation is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register access to enable hardware flow control depends on the
device port number and not the port minor number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the no longer used endpoint-array access completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The outcont_endpoints array was indexed using the port minor number
(which can be greater than the array size) rather than the device port
number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus port-number check in open and close, which prevented this
driver from being used with a minor number different from zero.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you want to download Infineon modem via USB, this Infineon USB
flashloader driver is required.
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Option GTM681W uses a qualcomm chip and can be
served by the qcserial device driver.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a specifier we may use to dump small buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control and bulk-message timeouts are specified in milliseconds and
should not depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bulk-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840:
add support for MCS7810 devices") which used stack-allocated buffers for
control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The read_mos_reg function is called with stack-allocated buffers, which
must not be used for control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first and second interrupt-in urbs are swapped for some Treo/Kyocera
devices, but the urb context was never updated with the new port.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rebranded Novatel E371 for AT&T's LTE bands.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'qt2_process_read_urb' is referenced only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to grab disconnect mutex in chars_in_buffer now that no
sub-driver is or should be querying hardware buffers anymore. (They
should use wait_until_sent.)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 2c992cd73 ("USB:
ti_usb_3410_5052: query hardware-buffer status in chars_in_buffer")
without breaking tty_wait_until_sent (used by, for example, tcdrain,
tcsendbreak and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 263e1f9f ("USB:
io_ti: query hardware-buffer status in chars_in_buffer") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 6f602912 ("usb:
serial: ftdi_sio: Add missing chars_in_buffer function") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Reported-by: Stas Sergeev <stsp@list.ru>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb-serial port rather than tty as argument to get_modem_status.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic wait_until_sent implementation which polls for empty
hardware buffers using the new port-operation tx_empty.
The generic implementation will be used for all sub-drivers that
implement tx_empty but does not define wait_until_sent.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add wait_until_sent operation which can be used to wait for hardware
buffers to drain.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea fixes,
which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+md4ACgkQMUfUDdst+ymkSgCfZWIiCtiX/li0yJqSiRB4yYJx
Ex0AoNemOOf6ywvSOHPbILTbJ1G+c/PX
=JmvB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea
fixes, which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while"
* tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits)
USB: ehci-msm: USB_MSM_OTG needs USB_PHY
USB: OHCI: avoid conflicting platform drivers
USB: OMAP: ISP1301 needs USB_PHY
USB: lpc32xx: ISP1301 needs USB_PHY
USB: ftdi_sio: enable two UART ports on ST Microconnect Lite
usb: phy: tegra: don't call into tegra-ehci directly
usb: phy: phy core cannot yet be a module
USB: Fix initconst in ehci driver
usb-storage: CY7C68300A chips do not support Cypress ATACB
USB: serial: option: Added support Olivetti Olicard 145
USB: ftdi_sio: correct ST Micro Connect Lite PIDs
ARM: mxs_defconfig: add CONFIG_USB_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY
usb: phy: remove exported function from __init section
usb: gadget: zero: put function instances on unbind
usb: gadget: f_sourcesink.c: correct a copy-paste misnomer
usb: gadget: cdc2: fix error return code in cdc_do_config()
usb: gadget: multi: fix error return code in rndis_do_config()
usb: gadget: f_obex: fix error return code in obex_bind()
USB: storage: convert to use module_usb_driver()
...
The FT4232H used in the ST Micro Connect Lite has four hi-speed UART ports.
The first two ports are reserved for the JTAG interface.
We enable by default ports 2 and 3 as UARTs (where port 2 is a
conventional RS-232 UART)
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.
For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill custom closing_wait implementation and let the tty-layer handle it
instead.
Note that the port drain-delay is set to three characters to keep the
20ms delay after wait_until_sent at low baudrates (1200 baud) during close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant drain, which has already been handled by the tty-layer,
from break_ctl.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Query hardware-buffer status in chars_in_buffer should the write fifo be
empty.
This is needed to make the tty layer wait for hardware buffers to drain
on close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The line status register is only polled so let's not keep a possibly
outdated value in the port data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move write-fifo flushing from ti_drain to close where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant wait_until_sent, which has already been handled by the
tty-layer, from break_ctl.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit f40d78155 ("USB: io_ti: kill custom
closing_wait implementation") which made TIOCGSERIAL return the wrong
value for closing_wait.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate port-private data in port-probe rather than in attach.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port device for debug messages in interrupt-urb callback and remove
unused private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port interrupt-in urb rather managing a private one.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device uses the second interrupt-in endpoint of the interface for
reading. Stop abusing the port read urb and store a pointer to the
second interrupt-in urb as port-private data instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port interrupt-out urb rather than abusing the port write_urb
pointer and allocating a new urb at every open (but the first...).
Note that the write_urb abuse would have led to a double free should
there ever be interfaces with a bulk-out endpoint.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the more efficient generic read implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor read-urb processing, and add sanity checks on header and data
lengths.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant data-offset define, which was really just the header
length.
Add payload-size define and use the bulk-out size define for the actual
bulk-out size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up and fix typos in protocol comment.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the port private data, which contains the write sequence
number, is cleared at allocation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a sparse warning where we should be using NULL instead of 0
Cc: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wishbone is an open hardware SoC bus commonly used in FPGA
designs. Bus access can be serialized using the Etherbone
protocol <http://www.ohwr.org/projects/etherbone-core>.
This driver is intended to be used with devices which attach
their internal Wishbone bus to a USB serial interface using
the Etherbone protocol. A userspace library is required to
speak the protocol made available by this driver as ttyUSBx.
Signed-off-by: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add a missing usb device id for the GDMBoost V1.x device
The patch is against 3.9-rc5
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_tty_get might return a tty which is NULL. But it is
dereferenced unconditionally in edge_send. Stop dereferencing that by
sending usb_serial_port pointer around.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"len" comes from the USB transfer and it's probably correct. The thing
is that we already have similar checks like:
if (data[i] >= serial->num_ports) {
So adding a sanity test here matches the rest of the code and is a good
idea.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can remove the "if (urb->actual_length) {" check because checking for
"while (i < urb->actual_length) {" is sufficient. This lets us pull the
code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit eba0e3c3a0.
When merged together (usb-linus and usb-next), this fix isn't needed and
causes a build error. Revert the commit to solve the build issue.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It enhances the driver for FTDI-based USB serial adapters
to recognize Mitsubishi Electric Corp. USB/RS422 Converters
as FT232BM chips and support them.
https://search.meau.com/?q=FX-USB-AW
Signed-off-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Tested-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan's 'fix use-after-free in TIOCMIWAIT' patchset[1] introduces
one bug which can cause kernel hang when opening port.
This patch initialized the 'port->delta_msr_wait' waitqueue head
to fix the bug which is introduced in 3.9-rc4.
[1], http://marc.info/?l=linux-usb&m=136368139627876&w=2
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in close. This
can never happen as close is guaranteed to be called before the last tty
reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in read bulk
callback. This can never happen as the port read urb is killed (and
poisoned) at close, which in turn is guaranteed to be called before the
last tty reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in close. This
can never happen as close is guaranteed to be called before the last tty
reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary disconnect test in tiocmset. No ioctls will be made
after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we return 0 or a negative error number appropriate for
userspace on errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary disconnect test in tiocmset. No ioctls will be made
after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we return 0 or a negative error number appropriate for
userspace on errors.
Currently 1 rather than 0 is returned on successful operation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove disconnected test from close which did not protect any device IO
at all.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fetch modem status on carrier_raised and tiocmget.
This driver appeared to support modem-status but only read the modem
status registers once at open and then used that cached value for all
further enquires.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reimplement device type detection using the device id table and quirks.
Device type was used to detect one device type which did not support to
control functions. Add quirks to the device table and store them in the
private port data at probe instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass usb-serial port to the control functions for uart status and work
mode.
Use port device for debugging and use dev_err to report errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken uart-error handling.
This driver appears to implement uart-error handling but does not
receive status interrupts or status information with bulk in transfers.
Instead status was retrieved at open and used to flag only the first
bulk in transfer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken TIOCMIWAIT support.
This drivers appears to implement TIOCMIWAIT but has no means of
receiving modem-status interrupts.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out TIOCMIWAIT handling from custom ioctl operation and use
tiocmiwait operation field instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Note that the interrupt counters will no longer be reset at open which
is in accordance with which how the other drivers work.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove SMP memory barriers from icount handling and rely on the barriers
implied by wait_event, sleep and locks, while using the port lock to
guarantee atomicity.
This is a step in moving over to the generic icount implementations.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken get_icount and TIOCMIWAIT support.
The driver has an icount structure but it is never been updated which
makes get_icount rather pointless and causes TIOCMIWAIT to always return
-EIO.
Note that the TIOCMIWAIT implementation has always been broken and would
not work even if icount support was added as it does not wait for the
modem status to change (does not use a work queue at all).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused, private modem-status wait queue from driver. If
TIOCMIWAIT is ever implemented it must not rely on a private wait queue
which may have been released when woken up.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Note that the interrupt counters will no longer be reset at open which
is in accordance with which how the other drivers work.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Note that the interrupt counters will no longer be reset at open which
is in accordance with which how the other drivers work.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out TIOCMIWAIT handling from custom ioctl operation and use
tiocmiwait operation field instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused, private modem-status wait queue from driver. If
TIOCMIWAIT is ever implemented it must not rely on a private wait queue
which may have been released when woken up.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect as wake up was only done in dtr_rts which isn't
guaranteed to be called (e.g. if HUPCL is not set).
Also remove the redundant wake-up call from dtr_rts.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port-data icount for interrupt counters.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic get_icount implementation that subdrivers relying on the
port interrupt counters can use.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure processes waiting for modem-status changes are woken up at
disconnect.
This is needed for custom subdriver TIOCMIWAIT-implementations which do
not yet handle hangup.
Even though processes on the tty-port wait queue are woken up at hangup
the wake-up call in usb-serial disconnect is still needed if a woken-up
process may go back to sleep (e.g. due to an incomplete
TIOCMIWAIT-implementation). If a disconnect occurs after a hangup, any
process waiting for changes will not be woken up a second time by the
tty-layer as the port will then have been disassociated from the tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic TIOCMIWAIT implementation which correctly handles hangup,
USB-device disconnect, does not rely on the deprecated sleep_on
functions and hence does not suffer from the races currently affecting
several usb-serial drivers.
This makes it much easier to add TIOCMIWAIT support to subdrivers as the
tricky details related to hangup and disconnect (e.g. atomicity, that
the private port data may have been freed when woken up, and waking up
processes at disconnect) have been handled once and for all.
To add support to a subdriver, simply set the tiocmiwait-port-operation
field, update the port icount fields and wake up any process sleeping on
the tty-port modem-status-change wait queue on changes.
Note that the tty-port initialised flag can be used to detect
disconnected as the port will be hung up as part of disconnect (and
cannot be reactivated due to the disconnected flag). However, as the
tty-port implementation currently wakes up processes before calling port
shutdown, the tty-hupping flag must also be checked to detect hangup for
now.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to unregister the tty-device before calling subdriver
port_remove.
This way remove will reverse probe, and specifically any port data
released in port_remove will be available throughout tty unregister.
Note that the order currently does not matter as the tty-layer can make
callbacks also after the device has been unregistered. This is
handled in usb-serial core using the disconnected flag, which is
already set when usb-serial bus device remove is called.
Cc: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_poison_urb to reliably kill all urbs on disconnect and suspend.
This way there will be no question that the urbs cannot be resubmitted
by buggy subdrivers.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename port_release so that all usb_serial_port functions have a common
prefix.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not call kill_traffic (and usb_kill_urb) once disconnect
returns. Any pending urbs are killed at disconnect and new submissions
are prevented by usb_unbind_interface (and usb_disable_interface).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the interrupt urb submitted in port_probe is killed in
port_remove.
The interrupt-urb completion handler references the port and may get
called after port_remove has returned and the port has been
unregistered (although this is currently prevented by usb-serial core as
we are using a non-private urb).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most USB serial drivers are, and should be, using as much of the generic
implementation as possible.
Rename the fixup_generic function to a more descriptive name.
Reword the related debug message in a more neutral tone (and remember to
add the missing newline).
Finally, move the operations initialisation to after the initial sanity
checks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove empty generic release implementation and make the release
callback non-mandatory (like attach, probe and disconnect).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the now empty generic disconnect callback and make the disconnect
callback non-mandatory.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for the generic disconnect callback to stop the read
and write urbs a second time as this has already been taken care of by
close (which is called from hangup as part of disconnect).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic close operation will be used if the close field is left
uninitialised.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The disconnect callback is set to the generic implementation by
usb-serial core if NULL.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in
cleanup.
The device is never cleared, and cleanup is never called after a
completed disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Simplify urb killing, and remove some related debug and dead code while
at it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in
dtr_rts.
The device is never cleared, and disconnect is handled for dtr_rts in
usb-serial core anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Remove some out-commented bogus code while at it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant port number from debug output (already printed as part
of device name).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failed allocations already get an OOM message and a stack dump.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant port number from debug output (already printed as part
of device name).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant comments and fix some minor coding style issues.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the tty-port callbacks using a common prefix to more clearly
separate them from the tty and usb driver callbacks.
Rename serial_down to serial_port_shutdown to match the callback name.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass usb-serial port rather than usb device to set_control_lines, and
make sure port device is used for all port related debugging.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use interface rather than usb-serial device for debugging interface
related operations. This gives more descriptive messages, such as
[ 905.669436] pl2303 1-4.1:1.0: 0x40:0x1:0x8:0x0 0
rather than
[ 341.943535] usb 1-4.1: 0x40:0x1:0x8:0x0 0
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove kill of interrupt-in urb on close as it has never been submitted.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove kill of interrupt-in urb on close as it has never been submitted.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold