Tariq Toukan says:
====================
mlx4 fixes
This patchset contains several bug fixes from the team to the
mlx4 Eth driver.
Series generated against net commit:
c2f57fb97d "drivers: net: phy: mdio-xgene: Add hardware dependency"
v2:
* excluded some cleanup patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is down, tx drop counter update is not needed.
Updating the counter in this case can cause a kernel
panic as when the port is down, ring can be NULL.
Fixes: 63a664b7e9 ("net/mlx4_en: fix tx_dropped bug")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a capability check before enabling DCBX.
In addition, it re-organizes the relevant data structures,
and fixes a typo in a define.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_dcbnl_set_state() returns u8, the return value from
mlx4_en_setup_tc() could be negative in case of failure, so fix that.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_dcbnl_set_all() returns u8, so return value can't be negative in
case of failure.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a mistake in the hardware manual, the FWSLC and POST1-4 registers
were not documented and left out of the driver for RZ/A making the CAM
feature non-operational.
Additionally, when the offset values for POST1-4 are left blank, the driver
attempts to set them using an offset of 0xFFFF which can cause a memory
corruption or panic.
This patch fixes the panic and properly enables CAM.
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-xgene driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix P2P dump trigger
* prevent a potential null dereference in iwlmvm
* prevent an uninitialized value from being returned in iwlmvm
* advertise support for channel width change in AP mode
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
brcmfmac
* avoid potential stack overflow in brcmf_cfg80211_start_ap()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJX0UZGAAoJEG4XJFUm622bNrQH/1x1A5go1O0WT9LFz7xgowY9
LtcpDcyDsz0h+dn1d9VuncTuO8mSREP/zxcDyibhiwnrVXR00QM0F9VgPSlUxASH
PwM06NZACblCk/mqSzI79BJ8kNBlwIhcr6OXpwzlcvF9JMUIDu/hQCdRPPn0lDRI
XVJHrM7dP2ZB0sVKAbM7+1Q1Bnv5JetPUduu1jOBtk+HiGjOAsejTFOh6AsOqZzZ
ZUTKBJeGkDp3XEVnlgkhJ1Y9xPaMpke/yqAlOPIgP90Ghd2SMJHTHiW6S28P/W1F
FMtTMXbYzzHAHNVSnOMgJyWRm1xD/Y6sVkeyXTD40BgHYXZcB6uHVLnzjR4i4BY=
=teXL
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-09-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.8
iwlwifi
* fix P2P dump trigger
* prevent a potential null dereference in iwlmvm
* prevent an uninitialized value from being returned in iwlmvm
* advertise support for channel width change in AP mode
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
brcmfmac
* avoid potential stack overflow in brcmf_cfg80211_start_ap()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We move register_netdev() to the end of dwceqos_probe() to close any
races where the netdev callbacks are called before the initialization
has finished.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, without GSO, it was easy to identify it: if the chunk didn't
fit and there was no data chunk in the packet yet, we could fragment at
IP level. So if there was an auth chunk and we were bundling a big data
chunk, it would fragment regardless of the size of the auth chunk. This
also works for the context of PMTU reductions.
But with GSO, we cannot distinguish such PMTU events anymore, as the
packet is allowed to exceed PMTU.
So we need another check: to ensure that the chunk that we are adding,
actually fits the current PMTU. If it doesn't, trigger a flush and let
it be fragmented at IP level in the next round.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: couple of fixes
Couple of fixes from Ido and myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During port init, we currently set the port's type to Ethernet after
setting its MAC address. However, the hardware documentation states this
should be the other way around.
Align the driver with the hardware documentation and set the port's MAC
address after setting its type.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When neigh_init fails, we have to do proper cleanup including
router_fini call.
Fixes: 6cf3c971dc ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: fixes and trivial cleanup
First patch drops unnecessary version.h includes. Second one
drops support for pre-release versions of FW ABI. Removing
FW ABI 0.0 from supported set is particularly good since 0
could just be uninitialized memory. Last but not least I drop
unnecessary padding of frames on RX which makes us count bytes
incorrectly for the VF2VF traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to pad frames to ETH_ZLEN on RX.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more strict about FW versions. Drop support for old
transitional revisions which were never used in production.
Dropping support for FW ABI version 0.0.0.0 is particularly
useful because 0 could just be uninitialized memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary version.h includes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 76174004a0
(tcp: do not slow start when cwnd equals ssthresh )
introduced regression in TCP YeAH. Using 100ms delay 1% loss virtual
ethernet link kernel 4.2 shows bandwidth ~500KB/s for single TCP
connection and kernel 4.3 and above (including 4.8-rc4) shows bandwidth
~100KB/s.
That is caused by stalled cwnd when cwnd equals ssthresh. This patch
fixes it by proper increasing cwnd in this case.
Signed-off-by: Artem Germanov <agermanov@anchorfree.com>
Acked-by: Dmitry Adamushko <d.adamushko@anchorfree.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes 2016-09-07
The following series contains bug fixes for the mlx5e driver.
from Gal,
- Static code checker cleanup (casting overflow)
- Fix global PFC counter statistics reading
- Fix HW LRO when vlan stripping is off
From Bodong,
- Deprecate old autoneg capability bit and use new one.
From Tariq,
- Fix xmit more counter race condition
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vlan tagged packets were not parsed correctly
and assumed to be regular IPv4/IPv6 packets.
We should check for 802.1Q/802.1ad tags and update the lro header
accordingly.
This fixes the use case where LRO is on and rxvlan is off
(vlan stripping is off).
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when reading global PFC statistics we left the counter
iterator out of the equation and we ended up reading the same counter
over and over again.
Instead of reading the counter at index 0 on every iteration we now read
the counter at index (i).
Fixes: e989d5a532 ('net/mlx5e: Expose flow control counters to ethtool')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64 bits architectures unsigned long is longer than u32,
casting to unsigned long will result in overflow.
We need to first allocate an unsigned long variable, then assign the
wanted value.
Fixes: 665bc53969 ('net/mlx5e: Use new ethtool get/set link ksettings API')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous an_disable_cap position bit31 is deprecated to be use in driver
with newer firmware. New firmware will advertise the same capability
in bit29.
Old capability didn't allow setting more than one protocol for a
specific speed when autoneg is off, while newer firmware will allow
this and it is indicated in the new capability location.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the xmit_more counter before notifying the HW,
to prevent a possible use-after-free of the skb.
Fixes: c8cf78fe10 ("net/mlx5e: Add ethtool counter for TX xmit_more")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DATA and/or FIN are carried in a SYN/ACK message or SYN message,
we append an skb in socket receive queue, but we forget to call
sk_forced_mem_schedule().
Effect is that the socket has a negative sk->sk_forward_alloc as long as
the message is not read by the application.
Josh Hunt fixed a similar issue in commit d22e153718 ("tcp: fix tcp
fin memory accounting")
Fixes: 168a8f5805 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
ipsec 2016-09-08
1) Fix a crash when xfrm_dump_sa returns an error.
From Vegard Nossum.
2) Remove some incorrect WARN() on normal error handling.
From Vegard Nossum.
3) Ignore socket policies when rebuilding hash tables,
socket policies are not inserted into the hash tables.
From Tobias Brunner.
4) Initialize and check tunnel pointers properly before
we use it. From Alexey Kodanev.
5) Fix l3mdev oif setting on xfrm dst lookups.
From David Ahern.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git fixes for 4.8. Major changes:
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
User-space can choose to omit NL80211_ATTR_SSID and only provide raw
IE TLV data. When doing so it can provide SSID IE with length exceeding
the allowed size. The driver further processes this IE copying it
into a local variable without checking the length. Hence stack can be
corrupted and used as exploit.
Cc: stable@vger.kernel.org # v4.7
Reported-by: Daxing Guo <freener.gdx@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A regression was introduced in commit id 79d4db1214 ("ath9k: cleanup
led_pin initial") that broken the WLAN status led on my laptop with
AR9287 after suspending and resuming.
Steps to reproduce:
* Suspend (laptop)
* Resume (laptop)
* Observe that the WLAN led no longer turns ON/OFF depending on the
status and is always red
Even though for my case it only needs to be set to OUT in ath9k_start
but for consistency bring back the IN direction setting as well.
Fixes: 79d4db1214 ("ath9k: cleanup led_pin initial")
Cc: Miaoqing Pan <miaoqing@codeaurora.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: <stable@vger.kernel.org> # 4.7+
Link: https://bugzilla.kernel.org/show_bug.cgi?id=151711
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In general, when DAD detected IPv6 duplicate address, ifp->state
will be set to INET6_IFADDR_STATE_ERRDAD and DAD is stopped by a
delayed work, the call tree should be like this:
ndisc_recv_ns
-> addrconf_dad_failure <- missing ifp put
-> addrconf_mod_dad_work
-> schedule addrconf_dad_work()
-> addrconf_dad_stop() <- missing ifp hold before call it
addrconf_dad_failure() called with ifp refcont holding but not put.
addrconf_dad_work() call addrconf_dad_stop() without extra holding
refcount. This will not cause any issue normally.
But the race between addrconf_dad_failure() and addrconf_dad_work()
may cause ifp refcount leak and netdevice can not be unregister,
dmesg show the following messages:
IPv6: eth0: IPv6 duplicate address fe80::XX:XXXX:XXXX:XX detected!
...
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Cc: stable@vger.kernel.org
Fixes: c15b1ccadb ("ipv6: move DAD and addrconf_verify processing
to workqueue")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a code path where we are calling __iowrite64_copy() on
an address that is not 64-bit aligned. This causes an exception on
some architectures such as arm64. Fix that code path by using
__iowrite32_copy().
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting an IP address from an interface, there is a clean-up of
routes which refer to this local address. However, there was no check to
see that the VRF matched. This meant that deletion wasn't confined to
the VRF it should have been.
To solve this, a new field has been added to fib_info to hold a table
id. When removing fib entries corresponding to a local ip address, this
table id is also used in the comparison.
The table id is populated when the fib_info is created. This was already
done in some places, but not in ip_rt_ioctl(). This has now been fixed.
Fixes: 021dd3b8a1 ("net: Add routes to the table associated with the device")
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build of m32r was giving warning:
In file included from drivers/net/ethernet/smsc/smc91x.c:92:0:
drivers/net/ethernet/smsc/smc91x.h:448:0: warning: "SMC_inb" redefined
#define SMC_inb(ioaddr, reg) ({ BUG(); 0; })
drivers/net/ethernet/smsc/smc91x.h:106:0:
note: this is the location of the previous definition
#define SMC_inb(a, r) inb(((u32)a) + (r))
drivers/net/ethernet/smsc/smc91x.h:449:0: warning: "SMC_outb" redefined
#define SMC_outb(x, ioaddr, reg) BUG()
drivers/net/ethernet/smsc/smc91x.h:108:0:
note: this is the location of the previous definition
#define SMC_outb(v, a, r) outb(v, ((u32)a) + (r))
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm still struggling to get this fix right..
Changes since v2:
- do not blindly modify SKB contents according to Dave's legitimate
objection
Changes since v1:
- dropped disabling HW checksum offload for Zynq
- initialize checksum similar to net/ethernet/freescale/fec_main.c
-- >8 --
MACB/GEM needs the checksum field initialized to 0 to get correct
results on transmit in all cases, e.g. on Zynq, UDP packets with
payload <= 2 otherwise contain a wrong checksums.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neither the failure or success paths of ping_v6_sendmsg release
the dst it acquires. This leads to a flood of warnings from
"net/core/dst.c:288 dst_release" on older kernels that
don't have 8bf4ada2e2 backported.
That patch optimistically hoped this had been fixed post 3.10, but
it seems at least one case wasn't, where I've seen this triggered
a lot from machines doing unprivileged icmp sockets.
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now we use the 'readlock' both for protecting some of the af_unix
IO path and for making the bind be single-threaded.
The two are independent, but using the same lock makes for a nasty
deadlock due to ordering with regards to filesystem locking. The bind
locking would want to nest outside the VSF pathname locking, but the IO
locking wants to nest inside some of those same locks.
We tried to fix this earlier with commit c845acb324 ("af_unix: Fix
splice-bind deadlock") which moved the readlock inside the vfs locks,
but that caused problems with overlayfs that will then call back into
filesystem routines that take the lock in the wrong order anyway.
Splitting the locks means that we can go back to having the bind lock be
the outermost lock, and we don't have any deadlocks with lock ordering.
Acked-by: Rainer Weikusat <rweikusat@cyberadapt.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c845acb324.
It turns out that it just replaces one deadlock with another one: we can
still get the wrong lock ordering with the readlock due to overlayfs
calling back into the filesystem layer and still taking the vfs locks
after the readlock.
The proper solution ends up being to just split the readlock into two
pieces: the bind lock (taken *outside* the vfs locks) and the IO lock
(taken *inside* the filesystem locks). The two locks are independent
anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc says:
====================
vxlan: fix error reporting
This patchset improves checking for invalid configuration in VXLAN and
fixes problems with duplicated and inappropriate error messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_dev_configure outputs error messages before returning, no need to
print again the same mesages in vxlan_newlink. Also, vxlan_dev_configure may
return a particular error code for a different reason than vxlan_newlink
thinks.
Move the remaining error messages into vxlan_dev_configure and let
vxlan_newlink just pass on the error code.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, kernel accepts configurations such as:
ip l a type vxlan dstport 4789 id 1 group 239.192.0.1
ip l a type vxlan dstport 4789 id 1 group ff0e::110
However, neither of those really works. In the IPv4 case, the interface
cannot be brought up ("RTNETLINK answers: No such device"). This is because
multicast join will be rejected without the interface being specified.
In the IPv6 case, multicast wil be joined on the first interface found. This
is not what the user wants as it depends on random factors (order of
interfaces).
Note that it's possible to add a local address but it doesn't solve
anything. For IPv4, it's not considered in the multicast join (thus the same
error as above is returned on ifup). This could be added but it wouldn't
help for IPv6 anyway. For IPv6, we do need the interface.
Just reject a configuration that sets multicast address and does not provide
an interface. Nobody can depend on the previous behavior as it never worked.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following few steps will crash kernel -
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Linton says:
====================
net: smsc911x: Move phy and interrupt config
v2-v3: Move error handing into separate patch, replace a couple cases
of fixed errors with the errors being returned from the failing functions.
Hoist irq handler.
The smsc911x driver is doing a number of things in its probe routine that
should be delayed until the interface is started. Because of this, the module
cannot be unloaded, the phy states are incorrect/stale if the interface isn't
running, open's unnecessarily fail causing network configuration problems, and
the /proc/irq nodes are incorrectly named.
Clean up a number of these problems by moving the mdio and interrupt
configuration into the smsc911x_open routine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The /proc/irq/xx information is incorrect for smsc911x because
the request_irq is happening before the register_netdev has the
proper device name. Moving it to the open also fixes the case
of when the device is renamed.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the allocating/enabling interrupts
in the ndo_open routine move the irq handler before it.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move phy startup/shutdown into the smsc911x_open/stop routines. This
allows the module to be unloaded because phy_connect_direct is no longer
always holding the module use count. This one change also resolves a
number of other problems.
The link status of a downed interface no longer reflects a stale state.
Errors caused by the net device being opened before the mdio/phy was
configured. There is also a potential power savings as the phy's don't
remain powered when the interface isn't running.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the error handling in smsc911x open in preparation
for the mdio startup being moved here.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel deletion is delayed by both a workqueue (l2tp_tunnel_delete -> wq
-> l2tp_tunnel_del_work) and RCU (sk_destruct -> RCU ->
l2tp_tunnel_destruct).
By the time l2tp_tunnel_destruct() runs to destroy the tunnel and finish
destroying the socket, the private data reserved via the net_generic
mechanism has already been freed, but l2tp_tunnel_destruct() actually
uses this data.
Make sure tunnel deletion for the netns has completed before returning
from l2tp_exit_net() by first flushing the tunnel removal workqueue, and
then waiting for RCU callbacks to complete.
Fixes: 167eb17e0b ("l2tp: create tunnel sockets in the right namespace")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8eb30be035 ("ipv6: Create ip6_tnl_xmit") unsets
flowi6_proto in ip4ip6_tnl_xmit() and ip6ip6_tnl_xmit().
Since xfrm_selector_match() relies on this info, IPv6 packets
sent by an ip6tunnel cannot be properly selected by their
protocols after removing it. This patch puts flowi6_proto back.
Cc: stable@vger.kernel.org
Fixes: 8eb30be035 ("ipv6: Create ip6_tnl_xmit")
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller