Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains four Netfilter fixes for net, they are:
1) Fix Kconfig dependencies of new nf_dup_ipv4 and nf_dup_ipv6.
2) Remove bogus test nh_scope in IPv4 rpfilter match that is breaking
--accept-local, from Xin Long.
3) Wait for RCU grace period after dropping the pending packets in the
nfqueue, from Florian Westphal.
4) Fix sleeping allocation while holding spin_lock_bh, from Nikolay Borisov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d999297c3d ("tipc: reduce locking scope during packet reception")
we altered the packet retransmission function. Since then, when
restransmitting packets, we create a clone of the original buffer
using __pskb_copy(skb, MIN_H_SIZE), where MIN_H_SIZE is the size of
the area we want to have copied, but also the smallest possible TIPC
packet size. The value of MIN_H_SIZE is 24.
Unfortunately, __pskb_copy() also has the effect that the headroom
of the cloned buffer takes the size MIN_H_SIZE. This is too small
for carrying the packet over the UDP tunnel bearer, which requires
a minimum headroom of 28 bytes. A change to just use pskb_copy()
lets the clone inherit the original headroom of 80 bytes, but also
assumes that the copied data area is of at least that size, something
that is not always the case. So that is not a viable solution.
We now fix this by adding a check for sufficient headroom in the
transmit function of udp_media.c, and expanding it when necessary.
Fixes: commit d999297c3d ("tipc: reduce locking scope during packet reception")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_NET_VENDOR_CAVIUM is only used to hide/show config options and to
include subdirectories in the build, so it doesn't make sense to make it
tristate.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code for message reassembly is erroneously assuming that
the the first arriving fragment buffer always is linear, and then goes
ahead resetting the fragment list of that buffer in anticipation of
more arriving fragments.
However, if the buffer already happens to be non-linear, we will
inadvertently drop the already attached fragment list, and later
on trig a BUG() in __pskb_pull_tail().
We see this happen when running fragmented TIPC multicast across UDP,
something made possible since
commit d0f91938be ("tipc: add ip/udp media type")
We fix this by not resetting the fragment list when the buffer is non-
linear, and by initiatlizing our private fragment list tail pointer to
the tail of the existing fragment list.
Fixes: commit d0f91938be ("tipc: add ip/udp media type")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"openvswitch: Remove vport stats" removed the per-vport statistics, in
order to use the netdev's statistics fields.
"openvswitch: Fix ovs_vport_get_stats()" fixed the export of these stats
to user-space, by using the provided netdev_ops to collate them - but ovs
internal devices still use an unallocated dev->tstats field to count
packets, which are no longer exported by this api.
Allocate the dev->tstats field for ovs internal devices, and wire up
ndo_get_stats64 with the original implementation of
ovs_vport_get_stats().
On its own, "openvswitch: Fix ovs_vport_get_stats()" fixes the OOPs,
unmasking a full-on panic on arm64:
=============%<==============
[<ffffffbffc00ce4c>] internal_dev_recv+0xa8/0x170 [openvswitch]
[<ffffffbffc0008b4>] do_output.isra.31+0x60/0x19c [openvswitch]
[<ffffffbffc000bf8>] do_execute_actions+0x208/0x11c0 [openvswitch]
[<ffffffbffc001c78>] ovs_execute_actions+0xc8/0x238 [openvswitch]
[<ffffffbffc003dfc>] ovs_packet_cmd_execute+0x21c/0x288 [openvswitch]
[<ffffffc0005e8c5c>] genl_family_rcv_msg+0x1b0/0x310
[<ffffffc0005e8e60>] genl_rcv_msg+0xa4/0xe4
[<ffffffc0005e7ddc>] netlink_rcv_skb+0xb0/0xdc
[<ffffffc0005e8a94>] genl_rcv+0x38/0x50
[<ffffffc0005e76c0>] netlink_unicast+0x164/0x210
[<ffffffc0005e7b70>] netlink_sendmsg+0x304/0x368
[<ffffffc0005a21c0>] sock_sendmsg+0x30/0x4c
[SNIP]
Kernel panic - not syncing: Fatal exception in interrupt
=============%<==============
Fixes: 8c876639c9 ("openvswitch: Remove vport stats.")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6e28b00082 ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.
Fixes: 42a7b32b73 ("xfrm: Add oif to dst lookups")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default fix broadcast window size is currently set to 20 packets.
This is a very low value, set at a time when we were still testing on
10 Mb/s hubs, and a change to it is long overdue.
Commit 7845989cb4 ("net: tipc: fix stall during bclink wakeup procedure")
revealed a problem with this low value. For messages of importance LOW,
the backlog queue limit will be calculated to 30 packets, while a
single, maximum sized message of 66000 bytes, carried across a 1500 MTU
network consists of 46 packets.
This leads to the following scenario (among others leading to the same
situation):
1: Msg 1 of 46 packets is sent. 20 packets go to the transmit queue, 26
packets to the backlog queue.
2: Msg 2 of 46 packets is attempted sent, but rejected because there is
no more space in the backlog queue at this level. The sender is added
to the wakeup queue with a "pending packets chain size" number of 46.
3: Some packets in the transmit queue are acked and released. We try to
wake up the sender, but the pending size of 46 is bigger than the LOW
wakeup limit of 30, so this doesn't happen.
5: Subsequent acks releases all the remaining buffers. Each time we test
for the wakeup criteria and find that 46 still is larger than 30,
even after both the transmit and the backlog queues are empty.
6: The sender is never woken up and given a chance to send its message.
He is stuck.
We could now loosen the wakeup criteria (used by link_prepare_wakeup())
to become equal to the send criteria (used by tipc_link_xmit()), i.e.,
by ignoring the "pending packets chain size" value altogether, or we can
just increase the queue limits so that the criteria can be satisfied
anyway. There are good reasons (potentially multiple waiting senders) to
not opt for the former solution, so we choose the latter one.
This commit fixes the problem by giving the broadcast link window a
default value of 50 packets. We also introduce a new minimum link
window size BCLINK_MIN_WIN of 32, which is enough to always avoid the
described situation. Finally, in order to not break any existing users
which may set the window explicitly, we enforce that the window is set
to the new minimum value in case the user is trying to set it to
anything lower.
Fixes: 7845989cb4 ("net: tipc: fix stall during bclink wakeup procedure")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is decrementing the pointer, instead of the value stored in the
pointer. KASan detects it as an out of bounds reference.
Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes xennet_create_queues() may failed to created all requested
queues, we need to update num_queues to real created to avoid NULL
pointer dereference.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reset transport and unlock if misc_register failed.
Signed-off-by: Gao feng <omarapazanadi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philipp Kirchhofer says:
====================
net: mv643xx_eth: TSO TX data corruption fixes
as previously discussed [1] the mv643xx_eth driver has some
issues with data corruption when using TCP segmentation offload (TSO).
The following patch set improves this situation by fixing two data
corruption bugs in the TSO TX path.
Before applying the patches repeatedly accessing large files located on
a SMB share on my NSA325 NAS with TSO enabled resulted in different
hash sums, which confirmed that data corruption is happening during
file transfer. After applying the patches the hash sums were the same.
As this is my first patch submission please feel free to point out any
issues with the patch set.
[1] http://thread.gmane.org/gmane.linux.network/336530
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent a race between the TX DMA engine and the CPU the writing of the
first transmit descriptor must be deferred until all following descriptors
have been updated. The network card may otherwise start transmitting before
all packet descriptors are set up correctly, which leads to data corruption
or an aborted transmit operation.
This deferral is already done in the non-TSO TX path, implement it also in
the TSO TX path.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX DMA engine requires that buffers with a size of 8 bytes or smaller
must be 64 bit aligned. This requirement may be violated when doing TSO,
as in this case larger skb frags can be broken up and transmitted in small
parts with then inappropriate alignment.
Fix this by checking for proper alignment before handing a buffer to the
DMA engine. If the data is misaligned realign it by copying it into the
TSO header data area.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Schocher says:
====================
net, phy, smsc: add posibility to disable energy detect mode
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Therefore the property "smsc,disable-energy-detect" is
introduced.
Patch 1 introduces phy-handle support for the ti,cpsw
driver. This is needed now for the smsc phy.
Patch 2 adds the disable energy mode functionality
to the smsc phy
Changes in v2:
- add comments from Florian Fainelli
- I did not change disable property name into enable
because I fear to break existing behaviour
- add smsc vendor prefix
- remove CONFIG_OF and use __maybe_unused
- introduce "phy-handle" ability into ti,cpsw
driver, so I can remove bogus:
if (!of_node && dev->parent->of_node)
of_node = dev->parent->of_node;
construct. Therefore new patch for the ti,cpsw
driver is necessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.
This results in a forced speed of 1000 and RX/TX failure.
Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dc ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment
rtlwifi:
* rtl8821ae: Fix system lockups on boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWIdlLAAoJEG4XJFUm622bCrEH/jgABInQDEHR2NBfj1n3dYzG
W0jB3nxBR4EgRc7W73Fca8MWduhWxOJGJ8+awlvrsv2bLaLT4W228jB2BoYYzhxK
rMWziGURcAN2x9BcWN30fIl7pLs23rQorSZZFhInJ1yuVqTViI2z872wix9qbQVj
7BdgorH5EEHqBQMIn14nWUMNXl/m63SMQZf+aR+NSRs8KF6hgG4CEUDIFRU+IRHO
+bH/z7xdzNK+QziOIeNBZQ0xBUXD7C32c7wIVuqf5Tx5Eku3rOVb+OSWpX/y0FRy
CqTIaZuO4fEgyPQH8PAEmngAuM+7wGVdgRZEXxvYM/I2kpGFFnQraKg1Dmv93xI=
=Dz9Y
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-10-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment
rtlwifi:
* rtl8821ae: Fix system lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.
This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2015-10-16
First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.
The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.
The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.
I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since vzalloc can be failed in memory pressure,
writes -ENOMEM to xenstore to indicate error.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.
netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.
Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).
It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.
This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes for the I2C subsystem.
Kieran found a flaw in the recently renewed wake irq handling. Mika
handled a user bug report where the ACPI info turned out to be
unusable. I updated MAINTAINERS so that such bug reports will sooner
get to the right people. Geert pointed me to a problem of some i2c
drivers regarding PM which I fixed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
i2c: designware-platdrv: enable RuntimePM before registering to the core
i2c: s3c2410: enable RuntimePM before registering to the core
i2c: rcar: enable RuntimePM before registering to the core
i2c: return probe deferred status on dev_pm_domain_attach
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Pull irq/timer fixes from Thomas Gleixner:
"irq: a fix for the new hierarchical MSI interrupt handling which
unbreaks PCI=n configurations.
timers: a fix for the new hrtimer clock offset update mechanism to
ensure that the boot time offset is respected"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Increment clock_was_set_seq in timekeeping_init()
Greg reported crashes hitting the following check in __sk_backlog_rcv()
BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));
The pfmemalloc bit is currently checked in sk_filter().
This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.
For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.
Fixes: b4b9e35585 ("netvm: set PF_MEMALLOC as appropriate during SKB processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 00590fdd5b introduced RCU locking in list type and in
doing so introduced a memory allocation in list_set_add, which
is done in an atomic context, due to the fact that ipset rcu
list modifications are serialised with a spin lock. The reason
why we can't use a mutex is that in addition to modifying the
list with ipset commands, it's also being modified when a
particular ipset rule timeout expires aka garbage collection.
This gc is triggered from set_cleanup_entries, which in turn
is invoked from a timer thus requiring the lock to be bh-safe.
Concretely the following call chain can lead to "sleeping function
called in atomic context" splat:
call_ad -> list_set_uadt -> list_set_uadd -> kzalloc(, GFP_KERNEL).
And since GFP_KERNEL allows initiating direct reclaim thus
potentially sleeping in the allocation path.
To fix the issue change the allocation type to GFP_ATOMIC, to
correctly reflect that it is occuring in an atomic context.
Fixes: 00590fdd5b ("netfilter: ipset: Introduce RCU locking in list type")
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name(). We could make
of_clk_get_parent_name() more robust, but that may have unintended
side-effects, so we'll do that in the next version.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kSCW
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"Just one revert for Armada XP devices: the conversion to
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name().
We could make of_clk_get_parent_name() more robust, but that
may have unintended side-effects, so we'll do that in the
next version"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
one for a v4.3-rc5 thinko in DM snapshot).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWIVMAAAoJEMUj8QotnQNaUmQH/3/zAJbGRL7WBdPRMdG1Fq5G
nM4I3wUcorLWaZZZ6jpN3A4zX+UIOscH/Si6/33pV7+wG3JuvIcOgZQ7CBLW6Ipl
D8JqpIjG5yfO71CPFIzhM/aHlJCjAj79Ejyj0W9ci2xntbglIxYcipSd55P4LgzU
7Yu1mA32gHHIN0sghvZEVIpavwYV6RRxhTEwxYP0GeTc3PRpUbSyuYJijlWVPH8T
orTg5SeqRLDymYLMRrGs8lHlOBhbKipXsZwfLwUq8zXIBYFseKdQpuac1u/HMJlS
ssnLUooQdOnSxxf8Vn/ozhD8BxKkO0jtVZ8OAb3PKXD4QDQgMXLXwNjxDyOU2DY=
=VCRB
-----END PGP SIGNATURE-----
Merge tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two DM target error path cleanup fixes (one for stable in DM thinp and
one for a v4.3-rc5 thinko in DM snapshot)"
* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix missing pool reference count decrement in pool_ctr error path
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
Pull btrfs fixes from Chris Mason:
"I have two more bug fixes for btrfs.
My commit fixes a bug we hit last week at FB, a combination of lots of
hard links and an admin command to resolve inode numbers.
Dave is adding checks to make sure balance on current kernels ignores
filters it doesn't understand. The penalty for being wrong is just
doing more work (not crashing etc), but it's a good fix"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix use after free iterating extrefs
btrfs: check unsupported filters in balance arguments
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework
that may cause it to violate PM QoS latency constraints in some
cases (Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips
that do not update the MPERF counter as often as expected by the
driver which may result in a divide by 0 (Srinivas Pandruvada).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=+ku3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two recent regressions (ACPICA, the generic power domains
framework) and one crash that may happen on specific hardware
supported since 4.1 (intel_pstate).
Specifics:
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework that
may cause it to violate PM QoS latency constraints in some cases
(Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips that
do not update the MPERF counter as often as expected by the driver
which may result in a divide by 0 (Srinivas Pandruvada)"
* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
ACPICA: Tables: Fix FADT dependency regression
PM / Domains: Fix validation of latency constraints in genpd governor
Pull drm fixes from Dave Airlie:
"Nothing too crazy or exciting:
- two MAINTAINERS entries that I didn't see the point in delaying.
- one drm mst fix to stop sending uninitialised data to monitors
- two amdgpu fixes
- one radeon mst tiling fix
- one vmwgfx regression fix
- one virtio warning fix.
I have found one locking problem that needs a bit of reorg to fix, but
I'm not sure it's worth putting in -fixes as I don't think we've seen
it hit in the real world ever, I just found it using the virtio-gpu
driver when working on it. I'll possibly send it next week once I've
time to discuss with Daniel"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/virtio: use %llu format string form atomic64_t
MAINTAINERS: Add myself as maintainer for the gma500 driver
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
drm/dp/mst: make mst i2c transfer code more robust.
drm/radeon: attach tile property to mst connector
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3ze+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
copy_user_page() is needed by DAX. Without this we get a compile error
for DAX on SH:
fs/dax.c:280:2: error: implicit declaration of function `copy_user_page' [-Werror=implicit-function-declaration]
copy_user_page(vto, (void __force *)vfrom, vaddr, to);
^
This was done with a random config that happened to include DAX support.
This patch has only been compile tested.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/built-in.o: In function `__bitrev32':
deftree.c:(.text+0x1e799): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7a0): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7b4): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7c1): undefined reference to `byte_rev_table'
Anything which uses bitrevX() has to select BITREVERSE, to grab
lib/bitrev.o.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following two locking commits in the DAX code:
commit 843172978b ("dax: fix race between simultaneous faults")
commit 46c043ede4 ("mm: take i_mmap_lock in unmap_mapping_range() for DAX")
introduced a number of deadlocks and other issues which need to be fixed
for the v4.3 kernel. The list of issues in DAX after these commits
(some newly introduced by the commits, some preexisting) can be found
here:
https://lkml.org/lkml/2015/9/25/602 (Subject: "Re: [PATCH] dax: fix deadlock in __dax_fault").
This undoes most of the changes introduced by those two commits,
essentially returning us to the DAX locking scheme that was used in
v4.2.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page_counter_memparse() returns pages for the threshold, while
mem_cgroup_usage() returns bytes for memory usage. Convert the
threshold to bytes.
Fixes: 3e32cb2e0a ("memcg: rename cgroup_event to mem_cgroup_event").
Signed-off-by: Shaohua Li <shli@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3716001bcb ("deb-pkg: add source package") added the ability to
create a debian changelog file. This exposed that previously the
builddeb script hasn't cleared debian/files between builds.
As debian/files keeps accumulating entries, the changes file will end up
growing indefinelty. With outdated entries in debian/files, builddeb
script will exit with failure. This regression impacts those who use
"make deb-pkg" target to build kernel into a .deb package and never use
"make mrproper" or other means to clean kernel tree from generated
directories.
To fix the regression, remove debian/files before starting build and in
the generated clean rule.
Fixes: 3716001bcb ("deb-pkg: add source package")
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Michal Marek <mmarek@suse.cz>
Cc: maximilian attems <maks@stro.at>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 6afdb859b7 ("mm: do not ignore mapping_gfp_mask in page cache
allocation paths") has caught some users of hardcoded GFP_KERNEL used in
the page cache allocation paths. This, however, wasn't complete and
there were others which went unnoticed.
Dave Chinner has reported the following deadlock for xfs on loop device:
: With the recent merge of the loop device changes, I'm now seeing
: XFS deadlock on my single CPU, 1GB RAM VM running xfs/073.
:
: The deadlocked is as follows:
:
: kloopd1: loop_queue_read_work
: xfs_file_iter_read
: lock XFS inode XFS_IOLOCK_SHARED (on image file)
: page cache read (GFP_KERNEL)
: radix tree alloc
: memory reclaim
: reclaim XFS inodes
: log force to unpin inodes
: <wait for log IO completion>
:
: xfs-cil/loop1: <does log force IO work>
: xlog_cil_push
: xlog_write
: <loop issuing log writes>
: xlog_state_get_iclog_space()
: <blocks due to all log buffers under write io>
: <waits for IO completion>
:
: kloopd1: loop_queue_write_work
: xfs_file_write_iter
: lock XFS inode XFS_IOLOCK_EXCL (on image file)
: <wait for inode to be unlocked>
:
: i.e. the kloopd, with it's split read and write work queues, has
: introduced a dependency through memory reclaim. i.e. that writes
: need to be able to progress for reads make progress.
:
: The problem, fundamentally, is that mpage_readpages() does a
: GFP_KERNEL allocation, rather than paying attention to the inode's
: mapping gfp mask, which is set to GFP_NOFS.
:
: The didn't used to happen, because the loop device used to issue
: reads through the splice path and that does:
:
: error = add_to_page_cache_lru(page, mapping, index,
: GFP_KERNEL & mapping_gfp_mask(mapping));
This has changed by commit aa4d86163e ("block: loop: switch to VFS
ITER_BVEC").
This patch changes mpage_readpage{s} to follow gfp mask set for the
mapping. There are, however, other places which are doing basically the
same.
lustre:ll_dir_filler is doing GFP_KERNEL from the function which
apparently uses GFP_NOFS for other allocations so let's make this
consistent.
cifs:readpages_get_pages is called from cifs_readpages and
__cifs_readpages_from_fscache called from the same path obeys mapping
gfp.
ramfs_nommu_expand_for_mapping is hardcoding GFP_KERNEL as well
regardless it uses mapping_gfp_mask for the page allocation.
ext4_mpage_readpages is the called from the page cache allocation path
same as read_pages and read_cache_pages
As I've noticed in my previous post I cannot say I would be happy about
sprinkling mapping_gfp_mask all over the place and it sounds like we
should drop gfp_mask argument altogether and use it internally in
__add_to_page_cache_locked that would require all the filesystems to use
mapping gfp consistently which I am not sure is the case here. From a
quick glance it seems that some file system use it all the time while
others are selective.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Dave Chinner <david@fromorbit.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Reflects ceph.git commit 7bfb7f9025a8ee0d2305f49bf0336d2424da5b5b.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Commit 30e2bc08b2 ("Revert "block: remove artifical max_hw_sectors
cap"") restored a clamp on max_sectors. It's now 2560 sectors instead
of 1024, but it's not good enough: we set max_hw_sectors to rbd object
size because we don't want object sized I/Os to be split, and the
default object size is 4M.
So, set max_sectors to max_hw_sectors in rbd at queue init time.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
timekeeping_init() can set the wall time offset, so we need to
increment the clock_was_set_seq counter. That way hrtimers will pick
up the early offset immediately. Otherwise on a machine which does not
set wall time later in the boot process the hrtimer offset is stale at
0 and wall time timers are going to expire with a delay of 45 years.
Fixes: 868a3e915f "hrtimer: Make offset update smarter"
Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stefan Liebler <stli@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
David S. Miller