The function is only used in one file, so move it up a
bit to avoid forward declarations and make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix a number of different checkpatch errors.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow to read management keys stored in a station's gtk key
array with a get_key function.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Verify that a pairwise key index value on ieee80211_get_key call
doesn't exceed the boundaries of the pairwise key array.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return value of ieee80211_ibss_csa_beacon is not aligned with the
return value of ieee80211_assign_beacon(). For consistency and to be
able to use both functions with similar code, change
ieee80211_ibss_csa_beacon() not to send the bss changed notification
itself, but return what has changed so the caller can send the
notification instead.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor ieee80211_ibss_process_chanswitch() to use
ieee80211_channel_switch() and avoid code duplication.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This regression was introduced in "mac80211: cache mesh
beacon".
mesh_sync_offset_adjust_tbtt() was assuming that the
beacon would be rebuilt in every single pre-tbtt
interrupt, but now the beacon update happens on the
workqueue, and it must be ready for immediate delivery to
the driver.
Save a pointer to the meshconf IE in the beacon_data (this
works because both the IE pointer and beacon buffer are
protected by the same rcu_{dereference,assign_pointer}())
for quick updates during pre-tbtt. This is faster and a
little prettier than iterating over the elements to find
the meshconf IE every time.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Keep the sched scan req when starting sched scan, and reschedule
it in case of HW restart during sched scan.
The upper layer don't have to know about the restart.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is not used anywhere else than in cfg.c, so there's no
need to export it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We call ieee80211_ibss_disconnect(), which requires sdata to be
locked, so lock the sdata during ieee80211_csa_connection_drop_work().
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Can be used to add extra IEs (such as P2P NoA) without having to
reallocate the buffer.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AP interface is stopped, free all AP and VLAN keys at
once to only require synchronize_net() once. Since that does
synchronize_net(), also move two such calls into the function
(using the new force_synchronize parameter) to avoid doing it
twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Teach sta_info_flush() to optionally also remove stations
from all VLANs associated with an AP interface to optimise
the station removal (in particular, synchronize_net().)
To not have to add the vlans argument throughout, do some
refactoring.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to have one synchronize_net() for each
removed station, refactor the code slightly to have just
a single synchronize_net() for all stations.
Note that this is currently useless as hostapd removes
stations one by one and this coalescing never happens.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to do this inside the sta key removal
since the keys can only be reached through the sta (and
not by the driver at all) so once the sta can no longer
be reached, the keys are safe.
This will allow further optimisation opportunities with
multiple stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.
This should speed up some scenarios like hostapd shutdown.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer should be cleared before synchronize_rcu() so that the
consequently dead station won't be found by any lookups in the TX
or RX paths.
Also check that the station is actually the one being removed, the
check is not needed because each 4-addr VLAN can only have a single
station and non-4-addr VLANs always have a NULL pointer there, but
the code is clearer this way (and we avoid the memory write.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 allows drivers to keep RCU-protected station
references that are cleared when the station is removed from the
driver and consequently needs to synchronize twice, once before
removing the station from the driver (so it can guarantee that
the station is no longer used in TX towards the driver) and once
after the station is removed from the driver.
Add a new pre-RCU-synchronisation station removal operation to
the API to allow drivers to clear/invalidate their RCU-protected
station pointers before the RCU synchronisation.
This will allow removing the second synchronisation by changing
the driver API so that the driver may no longer assume a valid
RCU-protected pointer after sta_remove/sta_state returns.
The alternative to this would be to synchronize_rcu() in all the
drivers that currently rely on this behaviour (only iwlmvm) but
that would defeat the purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes a regression introduced by my patch "mac80211: don't cancel
csa finalize work within stop_ap", which added sdata locks to
ieee80211_csa_finalize_work() without removing the locking for
ieee80211_ibss_finish_csa(), which is called by the former, resulting
in a deadlock due to nested locking.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On scan completion we try start any pending roc.
However, if scan was just pending (and not actually started)
there is no point in trying to start the roc, as it might
have started already.
This solves the following warning:
WARNING: CPU: 0 PID: 3552 at net/mac80211/offchannel.c:269 ieee80211_start_next_roc+0x164/0x204 [mac80211]()
[<c001cd38>] (unwind_backtrace+0x0/0xf0)
[<c00181d0>] (show_stack+0x10/0x14)
[<c05c0d8c>] (dump_stack+0x78/0x94)
[<c0047c08>] (warn_slowpath_common+0x68/0x8c)
[<c0047c48>] (warn_slowpath_null+0x1c/0x24)
[<bf4d6660>] (ieee80211_start_next_roc+0x164/0x204 [mac80211])
[<bf4d5a74>] (ieee80211_scan_cancel+0xe8/0x190 [mac80211])
[<bf4df970>] (ieee80211_do_stop+0x63c/0x79c [mac80211])
[<bf4dfae0>] (ieee80211_stop+0x10/0x18 [mac80211])
[<c0504d84>] (__dev_close_many+0x84/0xcc)
[<c0504df4>] (__dev_close+0x28/0x3c)
[<c0509708>] (__dev_change_flags+0x78/0x144)
[<c0509854>] (dev_change_flags+0x10/0x48)
[<c055fe3c>] (devinet_ioctl+0x614/0x6d0)
[<c04f22a0>] (sock_ioctl+0x5c/0x2a4)
[<c0124eb4>] (do_vfs_ioctl+0x7c/0x5d8)
[<c012547c>] (SyS_ioctl+0x6c/0x7c)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, determining the completed scan type was
done by testing the SCAN_HW_SCANNING flag.
However, this doesn't take care for the case in which
the hw scan was requested, but hasn't started yet (e.g.
due to active remain_on_channel).
Replace this test by checking whether ops->hw_scan is
defined.
This solves the following warning:
WARNING: CPU: 0 PID: 3552 at net/mac80211/offchannel.c:156 __ieee80211_scan_completed+0x1b4/0x2dc [mac80211]()
[<c001cd38>] (unwind_backtrace+0x0/0xf0)
[<c00181d0>] (show_stack+0x10/0x14)
[<c05c0d8c>] (dump_stack+0x78/0x94)
[<c0047c08>] (warn_slowpath_common+0x68/0x8c)
[<c0047c48>] (warn_slowpath_null+0x1c/0x24)
[<bf4d4504>] (__ieee80211_scan_completed+0x1b4/0x2dc [mac80211])
[<bf4d5a74>] (ieee80211_scan_cancel+0xe8/0x190 [mac80211])
[<bf4df970>] (ieee80211_do_stop+0x63c/0x79c [mac80211])
[<bf4dfae0>] (ieee80211_stop+0x10/0x18 [mac80211])
[<c0504d84>] (__dev_close_many+0x84/0xcc)
[<c0504df4>] (__dev_close+0x28/0x3c)
[<c0509708>] (__dev_change_flags+0x78/0x144)
[<c0509854>] (dev_change_flags+0x10/0x48)
[<c055fe3c>] (devinet_ioctl+0x614/0x6d0)
[<c04f22a0>] (sock_ioctl+0x5c/0x2a4)
[<c0124eb4>] (do_vfs_ioctl+0x7c/0x5d8)
[<c012547c>] (SyS_ioctl+0x6c/0x7c)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also
rename mcs to ht_mcs in struct cfg80211_bitrate_mask.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the unnecessary duplicate test of "if (skb) {"
when !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS.
Remove now unnecessary __maybe_unused, neaten comment
Remove unnecessary parenthesis around align cast.
Substitute reference to deprecated compare_ether_addr
with ether_addr_equal (in the comment.)
Signed-off-by: Joe Perches <joe@perches.com>
[edit commit log slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for vendor-specific commands to nl80211. This is
intended to be used for really vendor-specific functionality
that can't be implemented in a generic fashion for any reason.
It's *NOT* intended to be used for any normal/generic feature
or any optimisations that could be implemented across drivers.
Currently, only vendor commands (with replies) are supported,
no dump operations or vendor-specific notifications.
Also add a function wdev_to_ieee80211_vif() to mac80211 which
is needed for mac80211-based drivers wanting to implement any
vendor commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 488b366a45.
The code isn't used by anyone, and the Intel driver isn't planning
to use it either right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers with hardware rate control were given
sta->rx_nss set to 0. This was because rx_nss
calculation procedure was protected by hw/sw rate
control check.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When external CSA IEs are received (beacons or action messages), a
channel switch is triggered as well. This should only be allowed on
devices which actually support channel switches, otherwise disconnect.
(For the corresponding userspace invocation, the wiphy flag is checked
in nl80211).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current channel switch code has a potential deadlock:
1) * cfg80211_stop_ap acquires wdev-lock
* ieee80211_stop_ap calls cancel_work_sync for the csa_finalize_work,
which acquires the associated worker-lock
2) * ieee80211_csa_finalize_work holds the worker-lock when run
* it calls cfg80211_ch_switch_notify which will claim the wdev-lock,
and also needs to claim the sdata-lock (which is the same as the
wdev-lock) to modify the beacons.
It is sufficient to just set the channel switch active to false. If the
worker is running later, it will find the channel switch to not be
active anymore and returns immediately without changing anything.
Canceling the worker is done anyway when the interface goes down
(ieee80211_do_stop).
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa finalize worker needs to change the beacon information (for
different modes). These are normally protected under rtnl lock, but the
csa finalize worker is called by drivers and should not acquire the RTNL
lock. Therefore change access protection for beacons to sdata/wdev lock.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[fix sdata_dereference]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The local TSF timer is used to compute the timing offset between
mesh peers on beacon reception. However, asking the device for
the TSF is not very accurate, so we prefer to use rx->mactime
if available. In the latter case, calling drv_get_tsf() just
adds more delay into the RX path, so skip it if we can.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bug in tracking HT opmode changes in mac80211, it
fails to update the driver when the channel parameters don't
change.
Move the code to do the HT opmode checking independently of
the channel/bandwidth tracking.
Signed-off-by: Avri Altman <avri.altman@intel.com>
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All interface types now properly clean up their stations
using some form of sta_info_flush() themselves, so there's
no need to try it again at teardown. Remove the call to
get rid of the extra delay from the synchronize_net() and
rcu_barrier() calls.
Reported-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Measure TX latency and jitter statistics per station per TID.
These Measurements are disabled by default and can be enabled
via debugfs.
Features included for each station's TID:
1. Keep count of the maximum and average latency of Tx frames.
2. Keep track of many frames arrived in a specific time range
(need to enable through debugfs and configure the bins ranges)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM minstrel_ht does not check whether a sampling rate is supported.
Unsupported rates attempts can trigger when there are holes in bitfields
of supported MCSes belonging to the same group (e.g many devices are
MCS32 capable without MCS33->39 capable, also we systematically have a
hole for CCK rates).
Drop any attempts to sample unsupported rates, as suggested by Felix.
This is not a problem in minstrel which fills a per STA sample table
with only supported rates (though only at init).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM, only the first array value returned by get_random_bytes is used.
This change moves the call to get_random_bytes from the nested loop it
is in to its parent.
While at it, replace get_random_bytes with prandom_bytes since PRNs are
way enough for the selection process.
After this, minstrel_ht reclaims 80 PR-bytes instead of 640 R-bytes.
minstrels use sample tables to probe different rates in a randomized
manner.
minstrel_ht inits one single sample table upon registration (during
subsys_initcalls) and minstrel uses one per STA addition in minstrel.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Consecutive MCSes in [8*(NSS-1)->8*NSS[ have the same number NSS of
streams (except for MCS32 which is mishandled ATM).
ATM minstrel_ht uses MCS_GROUP_RATES in place of this 8 modulus.
This change replaces such occurences and by doing so allows for different
values of MCS_GROUP_RATES (e.g to cope with VHT MCS8,9).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new field to ieee80211_chanctx_conf to indicate
the min required channel configuration.
Tuning to a narrower channel might help reducing
the noise level and saving some power.
The min required channel definition is the max of
all min required channel definitions of the interfaces
bound to this channel context.
In AP mode, use 20MHz when there are no connected station.
When a new station is added/removed, calculate the new max
bandwidth supported by any of the stations (e.g. 80MHz when
80MHz and 40MHz stations are connected).
In other cases, simply use bss_conf.chandef as the
min required chandef.
Notify drivers about changes to this field by calling
drv_change_chanctx with a new CHANGE_MIN_WIDTH notification.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce shift and mask defines for beamformee STS cap and number
of sounding dimensions cap as these can take any 3 bit value.
While at it also cleanup an unrequired parenthesis.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no reason why we should have only one channel switch
announcement at a time for a single phy. When support for channel
switch with multiple contexts and multiple vifs per context is
implemented, we will need the chandef data for each vif. Move the
csa_chandef structure to sdata to prepare for this.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[Fixed compilation with mesh]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use put_unaligned_le16 and put_unaligned_le32 for
mesh_path_error_tx and mesh_path_sel_frame_tx.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use put_unaligned_le16 in mesh_plink_frame_tx.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg