PLATFORM_DEVID_AUTO can be used to have the platform core assign a
unique ID instead of manually creating one with IDA. Do this in all
applicable drivers.
Link: http://lkml.kernel.org/r/20160531204313.20979-1-afd@ti.com
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since many temperature sensors come "preconfigured" with a lower
precision, people are stuck at that precision when running on a kernel
based device (unlike the Dallas 1Wire library for e.g. Arduino, which
supports writing the configuration/scratchpad). This patch adds write
support for the scratchpad/precision registers via w1_slave sysfs.
Signed-off-by: Ben Sen <0.x29a.0@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kstrtoint() returns -ERANGE then "tmp" is uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polaykov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit enables the active pullup (APU bit) by default for
the DS2482 1-Wire master.
>From the DS2482 datasheet:
"The APU bit controls whether an active pullup (controlled slew-rate
transistor) or a passive pullup (Rwpu resistor) will be used to drive
a 1-Wire line from low to high. When APU = 0, active pullup is disabled
(resistor mode). Active Pullup should always be selected unless there is
only a single slave on the 1-Wire line."
According to the module author, Ben Gardner:
"It doesn't look like active pullup would cause any hurt if there
is only a single slave."
And my tests with multiple and single slaves on 1-Wire bus
confirms that.
This active pullup can be manually disabled using the introduced
module parameter:
active_pullup = 0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_process() calls try_to_freeze(), but the thread doesn't mark itself
freezable through set_freezable(), so the try_to_freeze() call is useless.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hdq_usecount was set to zero after a successful read, so
omap_hdq_put could not properly free resources which leads
e.g. to increasing usecounts in lsmod output
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's stop using legacy platform driver hooks for power management and
switch to using the standard dev_pm_ops-based hooks.
Also, instead of guarding PM methods with #ifdef CONFIG_PM annotate them
as __maybe_unused as it provides better compile coverage.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches makes following changes to omap_hdq driver
- Enable 1-wire mode.
- Implement w1_triplet callback to facilitate search rom
procedure and auto detection of 1-wire slaves.
- Proper enabling and disabling of interrupt.
- Cleanups (formatting and return value checks).
HDQ mode remains unchanged.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, memsetting and kfreeing the device is bad behaviour. The
device will have a reference count of 1 and hence can cause trouble
because it has kfree'd. Proper way to handle a failed device_register is
to call put_device right after it fails.
Signed-off-by: Levente Kurusa <levex@linux.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When initialized as a platform device the initializer must now specify
a device. An empty device name is no longer valid.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use module_pci_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return pci_register_driver(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { pci_unregister_driver(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_pci_driver;
@@
-module_exit(e);
+module_pci_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed there was a problem here because Smatch complained:
drivers/w1/slaves/w1_therm.c:416 w1_seq_show() warn:
inconsistent returns 'mutex:&sl->master->mutex'.
Locked on: line 416
Unlocked on: line 413
The problem is that we lock ->mutex but we unlock ->bus_mutex on error.
David Fries says that ->bus_mutex is correct and ->mutex is incorrect.
Fixes: d9411e57dc ('w1: Add support for DS28EA00 sequence to w1-therm')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The W1_42_FINISHED_BYTE is 0xFF so the cast means the condition is
never true.
Fixes: d9411e57dc ('w1: Add support for DS28EA00 sequence to w1-therm')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add i2c alias to enable autoloading of the module for device specified
in device-tree.
Signed-off-by: Ludek Hlavacek <ludek_h@seznam.cz>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides support for the DS28EA00 digital thermometer.
The DS28EA00 provides an additional two pins for implementing a sequence
detection algorithm. This feature allows you to determine the physical
location of the chip in the 1-wire bus without needing pre-existing
knowledge of the bus ordering. Support is provided through the sysfs
w1_seq file. The file will contain a single line with an integer value
representing the device index in the bus starting at 0.
Signed-off-by: Matt Campbell <mattrcampbell@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A temperature conversion can take 750 ms and when possible the
w1_therm slave driver drops the bus_mutex to allow other bus
operations, but that includes operations such as a periodic slave
search, which can remove this slave when it is no longer detected.
If that happens the sl->family_data will be freed and set to NULL
causing w1_slave_show to crash when it wakes up.
Signed-off-by: David Fries <David@Fries.net>
Reported-By: Thorsten Bschorr <thorsten@bschorr.de>
Tested-by: Thorsten Bschorr <thorsten@bschorr.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of 1-Wire devices commonly associated with physical access control
systems are attached/generate presence for as short as 100 ms - hence
the tens-to-hundreds milliseconds scan intervals are required.
Signed-off-by: Dmitry Khromov <dk@icelogic.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a new
subsystem, "coresight" has been added. Full details are in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSODosACgkQMUfUDdst+ykSNwCfcqx1Z3rQzbLwSrR2sa1fV3Zb
yEAAniJoLZ4ZkoQK4/1ozsFc31q+gXNm
=/epr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
1/ change request_module call to zero-pad single digit
family numbers. This appears to be the intention of
the code, but not what it actually does.
This means that the alias created for W1_FAMILY_SMEM_01
might actually be useful.
2/ Define a family name for the BQ27000 battery charge monitor.
Unfortunately this is the same number as W1_FAMILY_SMEM_01
so if both a compiled on a system, one module might need to
be blacklisted.
3/ Add a MODULE_ALIAS for the bq27000.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has no 'compatible' string and so is not found when
using device-tree.
Add one with value to match
hdqw1w: 1w@480b2000 {
device in omap3.dtsi.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adjust the bulk message timeout to the other ones (1000ms). Otherwise the
following dmesg errors can be seen on a Raspberry Pi:
[ 31.492386] Failed to read 1-wire data from 0x81: err=-110.
[ 31.504168] 0x81: count=-110, status:
[ 31.613404] Failed to read 1-wire data from 0x81: err=-110.
[ 31.621915] 0x81: count=-110, status:
[ 43.260968] Failed to read 1-wire data from 0x81: err=-110.
[ 43.270998] 0x81: count=-110, status:
[ 43.379959] Failed to read 1-wire data from 0x81: err=-110.
[ 43.388854] 0x81: count=-110, status:
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94859308a2 "w1: new w1_ds2406 driver" added a new driver
that uses the crc16 library, but didn't ensure that the core is
there. This adds the necessary Kconfig statements, just like we
have it for other w1 drivers.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Scott Alfter <scott@alfter.us>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the "masters"
subdirectory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the main "w1"
directory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the "slaves"
subdirectory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some preliminary work at making use of this driver led me to implement
CRC-16 checks on read and write to deal with the occasional glitchiness of
the 1-Wire bus. The revised driver (attached) returns an I/O error if the
CRC check fails. When reading the chip's state, either you get a valid
indication or you get an I/O error. When changing its state, either the
change is successful or an I/O error is returned.
Signed-off-by: Scott Alfter <scott@alfter.us>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace spaces at beginning of the string with tabs, and replace foo * bar with foo *bar in a pointer declaration.
Signed-off-by: Thomas Wood <tommyandrena@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX reference manual, the read/write bit operations
takes from 60 us to 120 us.
This patch optimizes mxc_w1_ds2_touch_bit() function to use proper
value for such delay. Nevertheless, a small margin for the timeout has
been added for the case if clock frequency is inaccurate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a software reset for 1-Wire module at driver startup.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX reference manual, the reset procedure and
"presence" pulse takes 511 and 512 us, respectively. Measurement for
i.MX27 is about 1100 us. There is no need to wait Reset+Presence
more than this time.
This patch optimizes mxc_w1_ds2_reset_bus() function to use proper
value for delay after w1 bus reset. Nevertheless, a small margin for
the timeout has been added for the case if clock frequency is inaccurate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
W1 reset_bus() should return zero if slave device is present.
This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_process_callbacks() expects to be called with dev->list_mutex held,
but it is the fact only in w1_process(). __w1_remove_master_device()
calls w1_process_callbacks() after it releases list_mutex.
The patch fixes __w1_remove_master_device() to acquire list_mutex
for w1_process_callbacks().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: David Fries <david@fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applications can submit a set of commands in one packet to the kernel,
and in some cases it is required such as reading the temperature
sensor results. This adds an option W1_CN_BUNDLE to the flags of
cn_msg to request the kernel to reply in one packet for efficiency.
The cn_msg flags now check for unknown flag values and return an error
if one is seen. See "Proper handling of unknown flags in system
calls" http://lwn.net/Articles/588444/
This corrects the ack values returned as per the protocol standard,
namely the original ack for status messages and seq + 1 for all others
such as the data returned from a read.
Some of the common variable names have been standardized as follows.
struct cn_msg *cn
struct w1_netlink_msg *msg
struct w1_netlink_cmd *cmd
struct w1_master *dev
When an argument and a function scope variable would collide, add req_
to the argument.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__w1_attach_slave_device calls device_add which calls w1_bus_notify
which calls the w1_bq27000 slave driver, which calls
platform_device_add and device_add and deadlocks on getting
&(&priv->bus_notifier)->rwsem as it is still held in the previous
device_add. This avoids the problem by processing the family
add/remove outside of the slave device_add call.
Commit 47eba33a09 introduced this deadlock and added
a KOBJ_ADD, as the add was already reported in device_register two add
events were being sent. This change suppresses the device_register
add so that any slave device sysfs entries are setup before the add
goes out.
Belisko Marek reported this change fixed the deadlock he was seeing on
ARM device tree, while testing on my x86-64 system never saw the
deadlock.
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: David Fries <David@Fries.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the message type is W1_MASTER_CMD or W1_SLAVE_CMD, then a reference
is taken when searching for the slave or master device. If there
isn't any following data m->len (mlen is a copy) is 0 and packing up
the message for later execution is skipped leaving nothing to
decrement the reference counts.
Way back when, m->len was checked before the search that increments the
reference count, but W1_LIST_MASTERS has no additional data, the check
was moved in 9be62e0b2f causing this bug.
This change reorders to put the check before the reference count is
incremented avoiding the problem.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps increasing build testing coverage.
To do this, __raw_{read,write}b() functions was be replaced with
simple {read,write}b() variants.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove old and currently wrong address of the FSF from license
parts of the code.
- Remove unused #include and sort remaining headers alphabetically.
- Remove unised definitions.
- Add definitions for bit-fields.
- Add missing module owner field.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix mxc_w1_ds2_reset_bus() return value.
According to i.MX reference manual, "presence status" reflected
in the bit 6 of control register.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configuration for masters and slaves is included only if W1 symbol
enabled, so no reason to check it once more.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_get_gpio() might return -EPROBE_DEFER meaning that the driver
providing the gpio isn't ready yet. If that happens for the first gpio
the resulting kernel output without this patch is:
w1-gpio somename: Failed to parse DT
platform somename: Driver w1-gpio requests probe deferral
The first message is misleading and so is suppressed with this patch.
Further if determining the gpio to switch the external pullup yields
-EPROBE_DEFER this error should be passed back to the caller instead of
just continuing without pullup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 64 bit systems, a large value for "long tmp" is truncated when
assigning to "int md->max_slave_count" so we still end up with a value
less than one despite the "tmp < 1" check.
This is more of a problem for static checkers than a real life issue,
but it's simple enough to fix.
Acked-by: David Fries <david@fries.net>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts ds1wm.c from commit d3a8a9dbb9.
Of the three files changed ds1wm.c ds2490.c and w1_netlink.c, it turns out
ds1wm.c was locking bus_mutex, but inside the loop and I missed it.
Reverting ds1wm.c to the previous version.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Fries <David@Fries.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bus_mutex needs to be taken to serialize access to a specific bus.
netlink wasn't updated when bus_mutex was added and was calling
without that lock held, and not all of the masters were holding the
bus_mutex in a search. This was causing the ds2490 hardware to stop
responding when both netlink and /sys slaves were executing bus
commands at the same time.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch the code documentation format style to DocBook format, enable
DocBook documentation generation, and fix some comments.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first line printed from w1_slave gives the context of the w1
device. So does the second line, but if the CRC check failed, the
second line contains the last successful result. It is confusing when
it prints the temperature next to the line that might be a previous
conversion and has nothing to do with that printed temperature value.
Modify the code to store the last good conversion in family_data,
which is designed for custom data structures.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware search was failing without the COMM_RST flag. Enabled
the flag and rewrote the function to handle more than one buffer of
results and to continuing where the search left off. Remove hardware
search note from the limitations now that it works. The "w1: ds2490
USB setup fixes" change went from 23.16 seconds to about 3 seconds,
this takes the time for the search down to .307346 seconds.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling usb_reset_configuration after usb_set_interface resets the
interface that was just selected, so call reset first.
Using alternative 3 greatly speeds the one wire search.
alt 0 or 1, 10ms int, 23.16 seconds
alt 2 or 3, 1ms int, 2.99 to 3.05 seconds
Use usb_interrupt_msg not usb_bulk_msg as it is an interrupt pipe
(bulk worked, it was just technically the wrong call).
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a #define for the usb vendor request type, clear the status
byte and use that instead of a magic offset in checking if idle.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unicast one wire replies back to the sender portid to avoid multiple
programs getting each other's messages, especially as the response
can't be uniquely identified with the sequence coming from the
requesting program when both programs generate the same id. Continue
to broadcast events such as add/remove master/slave devices.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows replying only to the requestor portid while still
supporting broadcasting. Pass 0 to portid for the previous behavior.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Netlink is a socket interface and is expected to be asynchronous.
Clients can now make w1 requests without blocking by making use of the
w1_master thread to process netlink commands which was previously only
used for doing an automatic bus search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce new commands to add, remove, and list slave devices through
the netlink interface. This can be useful to skip the search on a
static network. They could previously only be added or removed
through automatic search or sysfs, and this allows a program to only
use netlink.
Only allocate memory when needed, so move kzalloc into w1_get_slaves
where it was used.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Search will detect at most max_slave_count devices per run, if there
are more pick up the next search where the previous left off.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_max_slave_count is only used to abort the search early
or take a fast search (when 1), so there isn't any reason to not allow
it to be updated through sysfs. Memory is not allocated based on
the current value and 10 is a rather low base number, increasing to
64, and printing a message the first time the count is reached and
there were more devices to discover to let the user know why not
all the devices were found.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's valid to set the search count to 0 to stop searching, so don't
wake up the search thread to not search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before 63706172f3 "rework kthread_stop()" kthread_should_stop()
always returned false when called from a non-kthread task, after it
would oops as a non-kthread didn't have that structure and netlink was
calling search from a thread which wasn't a kthread. 9d1817cab2
"w1: fix oops when w1_search is called from netlink connector",
modified the code to avoid calling kthread_stop from a netlink thread.
Introduce a w1_master flag and bit W1_ABORT_SEARCH to identify abort
to cleanly support both kthread and netlink search abort. A search
can take seconds to run, so it is important to abort early if the
hardware is removed in the middle of a search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Marcin Jurkowski <marcin1j@gmail.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Sven Geggus <lists@fuchsschwanzdomain.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous logic,
if (avail > 8) {
store slave;
return;
}
send data; clear;
The logic error is, if there isn't space send the buffer and clear,
but the slave wasn't added to the now empty buffer loosing that slave
id. It also should have been "if (avail >= 8)" because when it is 8,
there is space.
Instead, if there isn't space send and clear the buffer, then there is
always space for the slave id.
Signed-off-by: David Fries <David@Fries.net>
Cc: stable@vger.kernel.org
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Base frequency should be as close as possible to 1 MHz. This patch
adds warnings when clock is unreliable, according to i.MX datasheet.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Private field "clkdiv" is not used outside "probe", so there are
no reason to keep it in driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to make
the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On architectures where long is more then 32 bits, modifying a 32-bit field
with set_bit (and other atomic bit operations) may cause bytes following
the field to by modified.
Because the endianness of the bits within a field is the native endianness
of the CPU[1], on big-endian machines, bit number zero is in the last byte
of the field.
Therefore, `set_bit(0, ptr)' on a 64-bit big-endian machine is roughly
equivalent to `((char *)ptr)[7] |= 1', and since w1 driver uses a 32-bit
field for holding the flags, this causes bytes beyond the field to be
modified.
[1] From Documentation/atomic_ops.txt:
Native atomic bit operations are defined to operate on objects
aligned to the size of an "unsigned long" C data type, and are
least of that size. The endianness of the bits within each
"unsigned long" are the native endianness of the cpu.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to make
the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The first DT gpio is necessary for this driver, but errors returned for
of_get_gpio are ignored.
This patch adds a return value check for the first of_get_gpio.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
request_module for w1 slave modules needs to be called with the w1
master mutex unlocked. Because w1_attach_slave_device gets always(?)
called with mutex locked, we need to temporarily unlock the w1 master
mutex for the loading of the w1 slave module.
Signed-off by: Hans-Frieder Vogt <hfvogt@gmx.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a check to make sure that fops are only called if they have
been defined by the slave module.
Without this check modules like w1_smem cause a NULL pointer dereference
bug.
Signed-off by: Hans-Frieder Vogt <hfvogt@gmx.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The driver core clears the driver data to NULL after device_release or on
probe failure. Thus, it is not needed to manually clear the device driver
data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The usage of strict_strtol() is not preferred, because strict_strtol() is
obsolete. Thus, kstrtol() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: David Stevenson <david@avoncliff.com>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Michael Arndt <michael@scriptkiller.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lets w1 slave drivers declare an attribute group, and not have to
create/destroy sysfs files directly. All w1 slave drivers will be fixed
to use this field up in follow-on patches to this one.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we have 2 sysfs files for the w1 slave devices, let the driver core
create / destroy them automatically by setting the default attribute
group for them, saving code and housekeeping logic.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
W1 slave sysfs files are created _after_ userspace is notified that the
device has been added to the system. Fix that race by moving the
creation/remove of the files to the bus notifier that is there for doing
this type of thing.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Power-up timing
The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled. When this occurs, the P0 port
does not respond to the Channel Access Write command. For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below. The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first. This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.
Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD
[akpm@linux-foundation.org: don't use kerenldoc token to introduce a non-kerneldoc comment, tweak whitespace]
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows the 1-wire bus to autoload the corresponding module
for each slave being attached.
This works similar to bluetooth protocols.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fails, and also add the return value check of
platform_device_add_data().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
De-activating this reading back will effectively half the time required
for a write to the output register.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Sat, Mar 02, 2013 at 10:45:10AM +0100, Sven Geggus wrote:
> This is the bad commit I found doing git bisect:
> 04f482faf5 is the first bad commit
> commit 04f482faf5
> Author: Patrick McHardy <kaber@trash.net>
> Date: Mon Mar 28 08:39:36 2011 +0000
Good job. I was too lazy to bisect for bad commit;)
Reading the code I found problematic kthread_should_stop call from netlink
connector which causes the oops. After applying a patch, I've been testing
owfs+w1 setup for nearly two days and it seems to work very reliable (no
hangs, no memleaks etc).
More detailed description and possible fix is given below:
Function w1_search can be called from either kthread or netlink callback.
While the former works fine, the latter causes oops due to kthread_should_stop
invocation.
This patch adds a check if w1_search is serving netlink command, skipping
kthread_should_stop invocation if so.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Josh Boyer <jwboyer@gmail.com>
Tested-by: Sven Geggus <lists@fuchsschwanzdomain.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 3.0+
Commit 8a1861d997 ("w1-gpio: Simplify & get rid of defines") removed the
compile guards from the device-tree id table, thereby generating a
warning when building without device-tree support.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8a1861d997 ("w1-gpio: Simplify & get rid of defines") changed
(apparently unknowingly) the driver to a hotpluggable platform-device
driver but did not not update the section markers for probe and remove
(to __devinit/exit, which have since been removed). A later commit fixed
the section mismatch for probe, but left remove marked with __exit.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.8
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRL81iAAoJEIwa5zzehBx38egP/jkD5elNVtJ9Pu2AzwOnfYNG
oNfoVRr189VcCxQ8sq9xocnZDPyJEZzR/wnrs0wiFcFaMU1qQJpR4EgG8zhifM8D
plIFnf9H3z1/p+XKk7NwPII2RcSEQQ7jfK3UaPg0tQVOgGJiOh/czoYTRNHCaoQY
RF0W1K01uR15Pee95USIBvllyveJrss54dFB9ON1xGgf3aAHtyoPy/7Robm1FZAd
14msm3cN2v1lWXrTYvL8d+8sK6cIm1lOGOpc/VBSX5sjEBMiuGwnIDvajEvXIXMB
DNvkK6WpWSQsVv0oDLgWSBcgqpEElHmbzOo0WTMdec4hjaoLHRbeLdoaA7On/kpj
XofbXoXtsM2O5VSumhSfOWFtu22W3E4ng69UE5UkKknq8n+CKA5J0NmMW3PmCWws
xk9bk9I1feqy4uVkgaihCV5o+gtawaG6vOBEClLoVF+D6INMGts1FBN/MNZCBLck
hZjgr1/tcPlK5VMrxnlQBGRKcaXV1uGU+RWcV4jA1xR5GM3fQWMXe4aQohcYqglO
lpHeZCfy5JDexY30jfA+ldcG27PxUIYqhapanYTmcXMCSO4XZ4o1gy8oxDLrUoXe
/Whi3csxcGhitkUBWvxAeoOTeWRJonwyqEPJ/LpdNgnPmj8tnZKo3tc5wEKEywMA
qVDu5M4yi3FfkDK+0vp9
=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
Also fixes some whitespace inconsistency in Kconfig and w1_family.h when
DS2408 chip support was added.
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
This fixes the following section mismatch:
WARNING: drivers/w1/masters/w1-gpio.o(.data+0x188): Section mismatch in
reference from the variable w1_gpio_driver to the function
.init.text:w1_gpio_probe()
The variable w1_gpio_driver references
the function __init w1_gpio_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_therm includes some obsolete code to detect bad_roms, this is no
longer relevant.
The retry code is only used for this bad_rom test, however there is a
CRC check that detects a bad read, but does not trigger a retry. This
patch removes all the bad_rom code and uses the CRC check to trigger
retries.
Signed-off-by: David Stevenson <david@avoncliff.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
At the same time, this fixes two faults. First, mdev, the result of
kzalloc, was never freed. Second, on failure of ioremap, 0 was returned.
This has been replaced by -EBUSY, which was the failure value for the call
to request_mem_region, with which the call to ioremap has been combined.
The warning message on failure of ioremap is dropped, because
devm_request_and_ioremap already gives such messages on failure.
Finally, the initial call to platform_get_resource is moved closer to the
call to devm_request_and_ioremap, which takes care of checking whether its
result is NULL, implying that a test on the result of this call to
platform_get_resource is not needed.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This slipped in through the merging of different trees. Remove
__devexit_p() use in the mxc_w1 driver.
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are not available on other architectures, so
let's limit them to omap.
If the driver subsystem maintainers want to build test
system wide changes without building for each target,
it's easy to carry a test patch that just strips out the
depends entries from Kconfig files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no reason to have the OF defines; it complicates the driver.
There's also no need for the funky platform_driver_probe.
Add a few warnings in case there's a failure; helps us find out
what went wrong.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are dealing with mxc_w1 registers.
While at it use dev_err() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using module_platform_driver() makes the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the new i.mx clock framework the mxc_w1 clock is registered as:
clk_register_clkdev(clk[owire_gate], NULL, "mxc_w1.0");
So we do not need to pass "owire" string and can use NULL instead.
While at it, also fix the clock error handling code.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
-----
Changes since v2:
- Add Ack's
Changes since v1:
- Fix clock error handling
drivers/w1/masters/mxc_w1.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Paul Walmsley <paul@pwsan.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my tree,
or in Andrew's (the lis3l driver changes came from his tree last week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3pcACgkQMUfUDdst+ymLswCcDYG9RkRcEdYwT5bOm1zM4IVl
WM0AoLKfC86g6xe4MdS7zROJn7ep/9qu
=zAHk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my
tree, or in Andrew's (the lis3l driver changes came from his tree last
week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (52 commits)
drivers/misc/lis3lv02d/lis3lv02d_i2c.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d: remove lis3lv02d driver DT init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add DT matching table passthru code
drivers/misc/lis3lv02d: add generic DT matching code
lis3lv02d: fix some comments specific to lis331dlh driver
MISC: hpilo, remove pci_disable_device
pcmcia: synclink_cs: fix potential tty NULL dereference
drivers/char/mmtimer.c: Remove useless kfree
drivers/char: removes unnecessary semicolon
char/misc: remove CONFIG_EXPERIMENTAL dependencies
mei: don't print buffer as a string
mei: struct mei_message_data doesn't have to be packed
mei: add error messages for open count errors
misc: use module_spi_driver
tifm: use module_pci_driver
misc/at25, dt: Improve at25 SPI eeprom device tree bindings.
mei: add lynx point pci device ids
mei: fix max number of open handles
mei: rename struct pci_dev *mei_device to mei_pdev
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
This patch adds support for maxim ds1825 based 1-wire temperature sensors.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the process of porting boards to devicetree implemenation, we should
keep information about external circuitry where they belong - the
individual drivers.
This patch adds a way to specify a GPIO to drive the (optional) external
pull-up logic, rather than using a function pointer for that.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add DT bindings to the w1-gpio driver, along with some
documentation on how to use them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let the driver compile everywhere while
also removing unnecessary headers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this lets us remove a bit of boilerplate code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
we have the helpful resource_size() macro to
calculate the size of the memory resource for
us, let's use it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes now
settled down. All we have here is some extcon driver updates, w1 driver
updates, a few printk cleanups that weren't needed for 3.5, but are good to
have now, and some other minor fixes/changes in the driver core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlARgIUACgkQMUfUDdst+ynDHgCfRNwIB9L+zZvjcKE5e1BhDbUl
wVUAn398DFgbJ1+PjGkd1EMR2uVTh7Ou
=MIFu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg Kroah-Hartman:
"Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes
now settled down. All we have here is some extcon driver updates, w1
driver updates, a few printk cleanups that weren't needed for 3.5, but
are good to have now, and some other minor fixes/changes in the driver
core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
printk: Export struct log size and member offsets through vmcoreinfo
Drivers: hv: Change the hex constant to a decimal constant
driver core: don't trigger uevent after failure
extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device
sysfs: fail dentry revalidation after namespace change fix
sysfs: fail dentry revalidation after namespace change
extcon: spelling of detach in function doc
extcon: arizona: Stop microphone detection if we give up on it
extcon: arizona: Update cable reporting calls and split headset
PM / Runtime: Do not increment device usage counts before probing
kmsg - do not flush partial lines when the console is busy
kmsg - export "continuation record" flag to /dev/kmsg
kmsg - avoid warning for CONFIG_PRINTK=n compilations
kmsg - properly print over-long continuation lines
driver-core: Use kobj_to_dev instead of re-implementing it
driver-core: Move kobj_to_dev from genhd.h to device.h
driver core: Move deferred devices to the end of dpm_list before probing
driver core: move uevent call to driver_register
driver core: fix shutdown races with probe/remove(v3)
Extcon: Arizona: Add driver for Wolfson Arizona class devices
...
Convert the OMAP HDQ driver to use runtime PM. Compile- and boot-tested,
but not tested in actual use.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Tested-by: NeilBrown <neilb@suse.de>
HDQ/1-wire registers are 32 bits long, even if the register contents
fit into 8 bits, so accesses must be 32-bit aligned. Evidently the
OMAP2/3 interconnects allowed the driver to get away with 8 bit accesses,
but the OMAP4 puts a stop to that:
[ 1.488800] Driver for 1-wire Dallas network protocol.
[ 1.495025] Bad mode in data abort handler detected
[ 1.500122] Internal error: Oops - bad mode: 0 [#1] SMP
[ 1.505615] Modules linked in:
[ 1.508819] CPU: 0 Not tainted (3.3.0-rc1-00008-g45030e9 #992)
[ 1.515289] PC is at 0xffff0018
[ 1.518615] LR is at omap_hdq_probe+0xd4/0x2cc
The OMAP4430 ES2 Rev X TRM does warn about this restriction in section
23.2.6.2 "HDQ/1-Wire Registers".
Fixes the crash on OMAP4430 ES2 Pandaboard. Tested also on OMAP34xx and
OMAP2420; it seems to work fine on those chips, although due to the lack
of boards with HDQ/1-wire devices here, a more indepth test was not
possible.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Allow the OMAP HDQ1W driver to be built for all OMAP2+ SoCs by
adjusting KConfig dependencies. The previous dependency required
either SOC_OMAP2430 or ARCH_OMAP3 to be set, but the HDQ IP block is
present on OMAP2420 and OMAP44xx SoCs. The driver was still
selectable on multi-OMAP kernel configurations, however; so the
previous prohibition was rather pointless.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
The 'mutex' in struct w1_master is use for two very different
purposes.
Firstly it protects various data structures such as the list of all
slaves.
Secondly it protects the w1 buss against concurrent accesses.
This can lead to deadlocks when the ->probe code called while adding a
slave needs to talk on the bus, as is the case for power_supply
devices.
ds2780 and ds2781 drivers contain a work around to track which
process hold the lock simply to avoid this deadlock. bq27000 doesn't
have that work around and so deadlocks.
There are other possible deadlocks involving sysfs.
When removing a device the sysfs s_active lock is held, so the lock
that protects the slave list must take precedence over s_active.
However when access power_supply attributes via sysfs, the s_active
lock must take precedence over the lock that protects accesses to
the bus.
So to avoid deadlocks between w1 slaves and sysfs, these must be
two separate locks. Making them separate means that the work around
in ds2780 and ds2781 can be removed.
So this patch:
- adds a new mutex: "bus_mutex" which serialises access to the bus.
- takes in mutex in w1_search and ds1wm_search while they access
the bus for searching. The mutex is dropped before calling the
callback which adds the slave.
- changes all slaves to use bus_mutex instead of mutex to
protect access to the bus
- removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the
related code from drivers/power/ds278[01]_battery.c which
calls them.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no gain in having a loop - there is no risk of missing the
interrupt with wait_event_timeout.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- some debug messages missed spaces
- sometimes no error was returned when it should have been
- sometimes a message is printed when there is no error, rather
than when there is one.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 59d4467be4.
Turns out it was the wrong version, will apply the correct version after
this.
Reported-by: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were some return statements around in the w1_uevent, used goto
to cleanup those return statements with the help of err variable,
and also removed a semi colon at the end of the w1_uevent's closing
brace.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1 devices need a mutex to serial IO. Most use master->mutex.
However that is used for other purposes and they can conflict.
In particular master->mutex is held while w1_attach_slave_device is
called.
For bq27000, this registers a 'powersupply' device which tries to read the
current status. The attempt to read will cause a deadlock on
master->mutex.
So create a new per-slave mutex and use that for serializing IO for
bq27000.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuexPAAoJEIwa5zzehBx3YBsP/0nFhXjb5t1PdLfFzGKtcZVB
j4zXWXMHQ1fA7wIfEpZF3Nnco6MQkufF5wJPoPdn1+wmkzCn3D6IwNVWVtW4U5i9
VGyShSbgusAAYXUe/9yYj8eN+bbRQSvdN4eWYWU6+rRXShGZ5dZZmp+IPNl54dnW
6F8uCnHX0cnIMCpGqV+41zZgZ/4wL2k9gdqu0LO6pi07o4tGd0Z4gcySgUFAnn1R
kofNHueYIP4UgOg8DREoBzVKlpRqMou3S2kSZUfMeb3Q9ryF7UIvaGqIILyi7PKL
kWd3nptg0EPavfL21SwXHiGpnDpB/Gj/F70kcPLus5RYujB24C9bvBmc26z68NZx
Sz9mbElkkIU5duZsl1nxBWJ8IZ/tSWdtmC2xQMznmV7gHyGgVwr4j47f4Uv5sBvM
14JHDO7mqN6E6FnTFZu/oPAN5pDjgL+TVNK5BU6Wkq0zitrA6eyKDqCvBCqkO6Nn
tNzOuyRDzMOwM7HzqXhxqtzJWXylO1Mldc4bM8X4Cocf4pnLna/X6uP6dgE6A+JY
azVYx4I/0NdEPerDTzIcEhBDgZeBVROhUQr+kHxc4rf6WzUUbu/wEo1UKXWV66oW
1jb1yAFFWqYjkQuQc2PD4JSx35sFJaoSaoneRtmzBzRDfzSr5KjKj1E0e1skyMFq
7ZVLCqZD0cB9DhmMDkWP
=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
There are three Kconfig entries with "--- help ---" attributes, and over
2000 Kconfig entries with "---help---" attributes. Apparently the three
attributes with embedded spaces are valid. Still, I see little reason
for using this obscure variant. And replacing those three attributes
with the common variant makes grepping Kconfig files for help texts a
bit easier too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NULL not 0 should be used with pointers. Just remove the offending
lines since they will default to NULL anyway.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f19420c1ac.
It contained lots of errors and warnings and shouldn't have ever been
applied, that was my fault, sorry.
Cc: Markus Franke <markus.franke@s2002.tu-chemnitz.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>,
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should unlock here before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch offers the possibility to disables irqs during w1_write_bit()
and w1_reset_bus() operations as timing requirements are very strict for
the 1-wire bus protocol. Per default interrupts are enabled but can be
disabled via the module parameter "w1_disable_irqs".
Extend 1-wire reset pulse length from 480us to 500us as 480us is the
minimum requirement for the 1-wire reset/presence pulse.
Signed-off-by: Markus Franke <franm@hrz.tu-chemnitz.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a 1-wire slave device driver for the DS28E04-100.
Signed-off-by: Markus Franke <franm@hrz.tu-chemnitz.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
If multiple threads try, they trip over each other badly.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is never used so remove it to avoid bit-rot.
It can trivially be re-added if there is ever a need.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As recent change means that we now dereference 'dev' before testing
for NULL.
That means either the change was wrong, or the test isn't needed.
As this function is only called from one driver (bq27x000_battery) and
it always passed a non-NULL dev, it seems good to assume that the
test isn't needed.
So remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_bq27000 adds a bq27000-battery platform device but does not provide
platform data for it. This causes the bq27x00 driver to dereference a NULL
pointer.
So provide the appropriate platform data. This requires modifying
w1_bq27000_read so that it find the w1 device as the parent of the bq device.
Also there is no point exporting w1_bq27000_read as nothing else uses it
or could use it. So make it static.
Finally, as there is no way to track how many batteries have been found, and
we will probably only find one, use an id number of '-1' to assert that this
is a unique instance.
Signed-off-by: NeilBrown <neilb@suse.de>
Tested-by: Thomas Weber <weber@corscience.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct inclusion of the asm header has long been deprecated by the
introduction of gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enables a much more efficient way of device searching. It uses the
1-wire read-rom operation which allows the direct reading of the slave
address. BUT this works only with exactly one slave on the bus.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
index c374978..9761950 100644
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the remaining USB drivers in the kernel to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Till Harbaum <till@harbaum.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w1_therm devices can either be bus powered or externally powered.
When device is bus powered during temperature conversion the bus
have to be left high to provide necessary power. Some masters also allow
strong power-up to be enabled in this case.
Naturally, no communication over bus can occur during that time.
However, if device has external power then there is no such restriction,
and host can talk to other devices during temperature conversion.
There is command which allows us to check how device is powered,
this patch uses it to release the bus on externally w1_therm powered devices
during temperature conversion.
Also, this changes uninterruptible sleeps there into interruptible ones to
avoid long uninterruptible sleep if w1 subsystem happens to grab bus for
scan during w1_therm_read().
Signed-off-by: Maciej Szmigiero <mhej@o2.pl>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Interrupting w1_delay() in w1_read_bit() results in missing the low level
on the w1 line and receiving "1" instead of "0".
Add local_irq_save()/local_irq_restore() around the critical section
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a nolock function to the w1 interface to avoid locking the
mutex if needed.
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straightforward. As an aside, the ida_init calls are not needed as far as
I can see needed. (DEFINE_IDA does the same already).
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Clifton Barnes <cabarnes@indesign-llc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It doesn't need the full module.h but it was getting moduleparam.h
from the fact that module.h was everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Give these files export.h so that they can reliably get the EXPORT_SYMBOL
and THIS_MODULE macros in the future, once module.h isn't implicitly
everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The for loop was looking for i <= 0 instead of i >= 0 so this function
never did anything. Also we started with i = NB_SYSFS_BIN_FILES instead
of "NB_SYSFS_BIN_FILES - 1" which is an off by one bug.
Reported-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jean-Franois Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:
: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.
This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves. Unfortunately,
this is not always the case. The sleep is restored but as a parameter to
the probe function in the pdata.
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew F. Davis