Now that cond_resched() also provides RCU quiescent states when
needed, it can be used in place of cond_resched_rcu_qs(). This
commit therefore documents this change.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The RCU CPU stall warnings have morphed significantly since the last
update, so this commit brings the documentation up to date.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
If a fast system has a worst-case grace-period duration of (say) ten
seconds, then running the same workload on a system ten times as slow
will get you an RCU CPU stall warning given default stall-warning
timeout settings. This commit therefore adds this possibility to
stallwarn.txt.
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
If a periodic interrupt's handler takes longer to execute than the period
between successive interrupts, RCU's kthreads and softirq handlers can
be prevented from executing, resulting in otherwise inexplicable RCU
CPU stall warnings. This commit therefore calls out this possibility
in Documentation/RCU/stallwarn.txt.
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit rearranges the Documentation/RCU/stallwarn.txt file to
put the list of issues that can cause RCU CPU stall warnings near
the beginning of the document.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Eric Engestrom <eric@engestrom.ch>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The Linux kernel outputs copious text during boot, and a slow serial
console can result in stall warnings, particularly when messages are
printed with interrupts disabled. This commit adds this to the list
of causes of RCU CPU stall warning messages.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The CONFIG_RCU_CPU_STALL_INFO has been default-y for a couple of
releases with no complaints, so it is time to eliminate this Kconfig
option entirely, so that the long-form RCU CPU stall warnings cannot
be disabled. This commit does just that.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit adds a message that is printed if the relevant grace-period
kthread has not been able to run for the two seconds preceding the
stall warning. (The two seconds is double the maximum interval between
successive bouts of quiescent-state forcing.)
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The current RCU CPU stall warning code will print "Stall ended before
state dump start" any time that the stall-warning code is triggered on
a CPU that has already reported a quiescent state for the current grace
period and if all quiescent states have been reported for the current
grace period. However, a true stall can result in these symptoms, for
example, by preventing RCU's grace-period kthreads from ever running
This commit therefore checks for this condition, reporting the end of
the stall only if one of the grace-period counters has actually advanced.
Otherwise, it reports the last time that the grace-period kthread made
meaningful progress. (In normal situations, the grace-period kthread
should make meaningful progress at least every jiffies_till_next_fqs
jiffies.)
Reported-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Miroslav Benes <mbenes@suse.cz>
Commit 6bfc09e232 ("rcu: Provide RCU CPU stall warnings for tiny RCU")
moved the rcu_cpu_stall_timeout module parameter from rcutree.c to
rcupdate.c, but failed to update Documentation/RCU/stallwarn.txt. This
commit therefore repairs this omission.
commit 96224daa16 ("documentation: Update sysfs path for rcu_cpu_stall_suppress")
updated the path for rcu_cpu_stall_suppress, but failed to update for
rcu_cpu_stall_timeout.
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
PREEMPT_RCU and TREE_PREEMPT_RCU serve the same function after
TINY_PREEMPT_RCU has been removed. This patch removes TREE_PREEMPT_RCU
and uses PREEMPT_RCU config option in its place.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The CONFIG_RCU_CPU_STALL_VERBOSE Kconfig parameter causes preemptible
RCU's CPU stall warnings to dump out any preempted tasks that are blocking
the current RCU grace period. This information is useful, and the default
has been CONFIG_RCU_CPU_STALL_VERBOSE=y for some years. It is therefore
time for this commit to remove this Kconfig parameter, so that future
kernel builds will always act as if CONFIG_RCU_CPU_STALL_VERBOSE=y.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit documents RCU-tasks stall warning messages and also describes
when to use the new cond_resched_rcu_qs() API.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Commit 6bfc09e232 (rcu: Provide RCU CPU stall warnings for tiny RCU)
moved the rcu_cpu_stall_suppress module parameter from rcutree.c to
rcupdate.c, but failed to update Documentation/RCU/stallwarn.txt. This
commit therefore repairs this omission.
Reported-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The full dynticks tree needs the latest RCU and sched
upstream updates in order to fix some dependencies.
Merge a common upstream merge point that has these
updates.
Conflicts:
include/linux/perf_event.h
kernel/rcutree.h
kernel/rcutree_plugin.h
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
We are planning to convert the dynticks Kconfig options layout
into a choice menu. The user must be able to easily pick
any of the following implementations: constant periodic tick,
idle dynticks, full dynticks.
As this implies a mutual exclusion, the two dynticks implementions
need to converge on the selection of a common Kconfig option in order
to ease the sharing of a common infrastructure.
It would thus seem pretty natural to reuse CONFIG_NO_HZ to
that end. It already implements all the idle dynticks code
and the full dynticks depends on all that code for now.
So ideally the choice menu would propose CONFIG_NO_HZ_IDLE and
CONFIG_NO_HZ_EXTENDED then both would select CONFIG_NO_HZ.
On the other hand we want to stay backward compatible: if
CONFIG_NO_HZ is set in an older config file, we want to
enable CONFIG_NO_HZ_IDLE by default.
But we can't afford both at the same time or we run into
a circular dependency:
1) CONFIG_NO_HZ_IDLE and CONFIG_NO_HZ_EXTENDED both select
CONFIG_NO_HZ
2) If CONFIG_NO_HZ is set, we default to CONFIG_NO_HZ_IDLE
We might be able to support that from Kconfig/Kbuild but it
may not be wise to introduce such a confusing behaviour.
So to solve this, create a new CONFIG_NO_HZ_COMMON option
which gathers the common code between idle and full dynticks
(that common code for now is simply the idle dynticks code)
and select it from their referring Kconfig.
Then we'll later create CONFIG_NO_HZ_IDLE and map CONFIG_NO_HZ
to it for backward compatibility.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
If RCU's softirq handler is prevented from executing, an RCU CPU stall
warning can result. Ways to prevent RCU's softirq handler from executing
include: (1) CPU spinning with interrupts disabled, (2) infinite loop
in some softirq handler, and (3) in -rt kernels, an infinite loop in a
set of real-time threads running at priorities higher than that of RCU's
softirq handler.
Because this situation can be difficult to track down, this commit causes
the count of RCU softirq handler invocations to be printed with RCU
CPU stall warnings. This information does require some interpretation,
as now documented in Documentation/RCU/stallwarn.txt.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The print_cpu_stall_fast_no_hz() function attempts to print -1 when
the ->idle_gp_timer is not pending, but unsigned arithmetic causes it
to instead print ULONG_MAX, which is 4294967295 on 32-bit systems and
18446744073709551615 on 64-bit systems. Neither of these are the most
reader-friendly values, so this commit instead causes "timer not pending"
to be printed when ->idle_gp_timer is not pending.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Add documentation of CONFIG_RCU_CPU_STALL_VERBOSE, CONFIG_RCU_CPU_STALL_INFO,
and RCU_STALL_DELAY_DELTA. Describe multiple stall-warning messages from
a single stall, and the timing of the subsequent messages. Add headings.
Remove RCU_SECONDS_TILL_STALL_RECHECK because this value is now computed
at runtime from RCU_CPU_STALL_TIMEOUT, so that sysfs changes to the timeout
value now directly affect the RCU_SECONDS_TILL_STALL_RECHECK value.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Update various files in Documentation/RCU to reflect srcu_read_lock_raw()
and srcu_read_unlock_raw(). Credit to Peter Zijlstra for suggesting
use of the existing _raw suffix instead of the earlier bulkref names.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
One of lclaudio's systems was seeing RCU CPU stall warnings from idle.
These turned out to be caused by a bug that stopped scheduling-clock
tick interrupts from being sent to a given CPU for several hundred seconds.
This commit therefore updates the documentation to call this out as a
possible cause for RCU CPU stall warnings.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The RCU CPU stall warnings can now be controlled using the
rcu_cpu_stall_suppress boot-time parameter or via the same parameter
from sysfs. There is therefore no longer any reason to have
kernel config parameters for this feature. This commit therefore
removes the RCU_CPU_STALL_DETECTOR and RCU_CPU_STALL_DETECTOR_RUNNABLE
kernel config parameters. The RCU_CPU_STALL_TIMEOUT parameter remains
to allow the timeout to be tuned and the RCU_CPU_STALL_VERBOSE parameter
remains to allow task-stall information to be suppressed if desired.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
CPU-bound real-time processes can cause RCU CPU stall warnings, and
much other trouble as well. Document the fact that they can cause
RCU CPU stall warnings.
Suggested-by: Darren Hart <dvhltc@us.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The existing Documentation/RCU/stallwarn.txt has proven unhelpful, so
rework it a bit. In particular, show how to interpret the stall-warning
messages.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Paul E. McKenney