Currently, default VHT configuration from the firmware is used
for the VHT operations. Adding vhtcfg command to configure the
firmware based on input received from cfg.
Enable VHT for AP mode only when cfg80211_ap_settings has a
VHT IE i.e., when ieee80211ac is set to 1 in the hostapd.conf.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add proper alignment at first packet copy, to avoid extra copies made later
in networking stack.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move processing of received packets to tasklet from hard-irq context.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX path has extra copying of packets, that can be avoided.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use dedicated DMA coherent buffers for RX urbs, to avoid allocation of large
skbuffs in hard-irq context and improve performance.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spin locks and completions are expensive in hard IRQ context and cause
problems with RT kernels. In RT kernels, both spin locks and
completions can schedule(), so we can't use them in hard irq context.
Move handling code into the irq thread function to avoid that.
Reported-by: Gregoire Gentil <gregoire@alwaysinnovating.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were printing out all the hex dumps regardless of whether dynamic
debugging was enabled or not. Now that print_hex_dump_debug() has
been implemented, we can use that instead.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't ignore dummy packets when our queues are empty. This causes dummy
packets never to be sent when traffic is not suspended by FW thresholds,
which happens only in high Tx throughput situations. This may hurt Rx
performance.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wlcore state was checked without the mutex being taken. This leads
to WARN_ONs sometimes if a notification arrives when the driver
is on, but the mutex is only taken after it is off. This usually
happens if stopping the driver while connected to a network.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the sequence number of the broadcast AP link in the wlvif. For each
connected station, save the sequence number in the drv_priv part of
ieee80211_sta. Use the saved numbers on recovery/resume, with the
obligatory increment on recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Dont use free_sta() on AP global links. It would fail an internal check
within the function and various structures within the link struct would
not be reset.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Print board type, PG with metal and ROM versions.
This might help debugging HW related issues.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For STA we report beacon loss to higher levels so that wpa_s
can attempt to roam without disconnecting. In case of P2P CLI
we don't want to attempt roaming and instead disconnect immediately
upon beacon loss.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On !CONFIG_SMP builds spin_is_locked always returns 0. Assert the
locking using assert_spin_locked, which is written to behave correctly
in all cases.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
report the average beacon rssi which is calculated
by firmware for roaming statistics instead of the
last rx packet rssi. this results a more accurate
rssi reporting
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Accumulate the total number of sent packets per-link to find out how far
the encryption sequence number has progressed. Use this number as the
initial security sequence number after recovery.
This consolidates security sequence handling for both chip families, as
we no longer have to rely on 12xx specific Tx completion.
A fortunate side effect of this is correct management of seq numbers for
AP roles and multi-role scenarios.
When a link is removed we save the last seq number on a persistent part
of the wlvif. This helps the data survive through recoveries/suspends,
which also entail changes in the hlid of the link.
This functionality is STA only currently.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The HLID of a STA can change, particularly during recovery. Don't cache
the HLID before it was potentially allocated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit 144614f3eebd7d only allowed a single active link when
turning on the optimization, ignoring the fact that an AP has two
additional global links.
Use 3 links as an indication for a single active link. Use the
FW PSM bits to verify the extra active link belongs to the AP role.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Maximum number of supported RX BA sessions depends on chip type.
wl18xx supports 5 RX BA sessions while wl12xx supports 3.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is requiered to enter sleep mode with smaller delay in forced PS mode.
This fixes issue of testing force PS mode during VoIP traffic where packets
are sent every 20ms. Chip never enters ps mode with default 30 ms delay
in such test.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Schedule different time event based on the ROC type
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Increase the maximal remain on channel time as longer remain
on channel requests are handled by the FW using fragmented
time events.
This reduces the number of user/kernel space iterations during
flows such as p2p_listen. In addition it is currently required
for flows which require longer duration such as p2p_sd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RF-kill wakeup trigger flag is set in the wrong command,
which means it won't work. Also fix the comment in the TCP
wakeup trigger code -- the firmware was changed to look at
all the different trigger flags.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should disable MIMO only if bt_traffic_load goes up to 3.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the right source of information for the valid Tx
antennas, not the NVM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This data should taken from TLVs and not from the NVM. This
is true for the value written in CSR_HW_IF_CONFIG_REG too.
Also, no need to set the CSR_HW_IF_CONFIG_REG_BIT_MAC_SI bit
for 7000 devices which are the only devices currently
supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In firmware "listener" (monitor) mode, we still need to
open up the filters with the filter flags to receive all
frames.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This has valuable data about RFkill state seen from the fw
side.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
5ghz_disable has no effect any longer, that was changed during
refactoring of EEPROM reading/parsing. Remove it, wpa_supplicant
allow now to specify frequencies, on which device will operate.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1. Quota for the monitor interface should be added only if there is
a channel context assigned to the interface.
2. In the unassign channel context flow, need to remove the quota
for the monitor interface binding, before unbinding.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This feature is not implemented yet in firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The masks were wrong. They should be 0xffffffff when SCO,
HID or SNIFF profiles are used. They should be 0xffff0000
in any other case (default) to get a bit more throughput
when the BT profile allows for it.
Fix a debug print on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If wpa_supplicant and iw/iwconfig are used together, very
rarely the system crashes. It seems to be related to the
connection parameters not being set up, but it's not all
clear to me how this happens. In any case, checking that
the conn pointer exists here is probably a good idea.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My new tracing code for ath6kl introduced these warnings on 64-bit:
trace.h:38:1: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'size_t' [-Wformat]
trace.h:61:1: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'size_t' [-Wformat]
trace.h:84:1: warning: format '%d' expects argument of type 'int',
but argument 6 has type 'size_t' [-Wformat]
trace.h:119:1: warning: format '%d' expects argument of type 'int',
but argument 7 has type 'size_t' [-Wformat]
trace.h:173:1: warning: format '%d' expects argument of type 'int',
but argument 3 has type 'size_t' [-Wformat]
trace.h:193:1: warning: format '%d' expects argument of type 'int',
but argument 5 has type 'size_t' [-Wformat]
trace.h:221:1: warning: format '%d' expects argument of type 'int',
but argument 5 has type 'size_t' [-Wformat]
Fix them by using %zd.
Reported-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode, don't attempt to program GTKs into the
device, they're used for TX only so not needed and
programming them causes error messages. Also, in
this case and if key programming fails, avoid trying
to remove the key that isn't present later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code removed in this patch was used for bring up on
older NICs. No MVM capable fw will ever be released for
older NICs, so remove that code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface change type, the CAB queue must be reassigned,
do this in hwsim to avoid warnings/crashes.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rafał Miłecki