Commit Graph

36 Commits

Author SHA1 Message Date
Hauke Mehrtens 3475372ff6 net: dsa: lantiq_gswip: Depend on HAS_IOMEM
The driver uses devm_ioremap_resource() which is only available when
CONFIG_HAS_IOMEM is set, make the driver depend on this config option.
User mode Linux does not have CONFIG_HAS_IOMEM set and the driver was
failing on this architecture.

Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-25 20:27:43 -07:00
Hauke Mehrtens 14fceff477 net: dsa: Add Lantiq / Intel DSA driver for vrx200
This adds the DSA driver for the GSWIP Switch found in the VRX200 SoC.
This switch is integrated in the DSL SoC, this SoC uses a GSWIP version
2.1, there are other SoCs using different versions of this IP block, but
this driver was only tested with the version found in the VRX200.
Currently only the basic features are implemented which will forward all
packages to the CPU and let the CPU do the forwarding. The hardware also
support Layer 2 offloading which is not yet implemented in this driver.

The GPHY FW loaded is now done by this driver and not any more by the
separate driver in drivers/soc/lantiq/gphy.c, I will remove this driver
is a separate patch. to make use of the GPHY this switch driver is
needed anyway. Other SoCs have more embedded GPHYs so this driver should
support a variable number of GPHYs. After the firmware was loaded the
GPHY can be probed on the MDIO bus and it behaves like an external GPHY,
without the firmware it can not be probed on the MDIO bus.

The clock names in the sysctrl.c file have to be changed because the
clocks are now used by a different driver. This should be cleaned up and
a real common clock driver should provide the clocks instead.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13 08:14:33 -07:00
Florian Fainelli 9aee398af3 net: dsa: Drop OF dependency for BCM_SF2
NET_DSA_BCM_SF2 does not need to depend on CONFIG_OF anymore since we have
stubs when that option is disabled.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-18 13:53:48 -07:00
Linus Walleij d8652956cf net: dsa: realtek-smi: Add Realtek SMI driver
This adds a driver core for the Realtek SMI chips and a
subdriver for the RTL8366RB. I just added this chip simply
because it is all I can test.

The code is a massaged variant of the code that has been
sitting out-of-tree in OpenWRT for years in the absence of
a proper switch subsystem. This creates a DSA driver for it.
I have tried to credit the original authors wherever
possible.

The main changes I've done from the OpenWRT code:

- Added an IRQ chip inside the RTL8366RB switch to demux and
  handle the line state IRQs.

- Distributed the phy handling out to the PHY driver.

- Added some RTL8366RB code that was missing in the driver at
  the time, such as setting up "green ethernet" with a funny
  jam table and forcing MAC5 (the CPU port) into 1 GBit.

- Select jam table and add the default jam table from the
  vendor driver, also for ASIC "version 0" if need be.

- Do not store jam tables in the device tree, store them
  in the driver.

- Pick in the "initvals" jam tables from OpenWRT's driver
  and make those get selected per compatible for the
  whole system. It's apparently about electrical settings
  for this system and whatnot, not really configuration
  from device tree.

- Implemented LED control: beware of bugs because there are
  no LEDs on the device I am using!

We do not implement custom DSA tags. This is explained in
a comment in the driver as well: this "tagging protocol" is
not simply a few extra bytes tagged on to the ethernet
frame as DSA is used to. Instead, enabling the CPU tags
will make the switch start talking Realtek RRCP internally.
For example a simple ping will make this kind of packets
appear inside the switch:

0000   ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00
0010   08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d
0020   a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00
0030   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

As you can see a custom "8899" tagged packet using the
protocol 0xa2. Norm RRCP appears to always have this
protocol set to 0x01 according to OpenRRCP. You can also
see that this is not a ping packet at all, instead the
switch is starting to talk network management issues
with the CPU port.

So for now custom "tagging" is disabled.

This was tested on the D-Link DIR-685 with initramfs and
OpenWRT userspaces and works fine on all the LAN ports
(lan0 .. lan3). The WAN port is yet not working.

Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-18 13:43:38 +09:00
Linus Walleij 05bd97fc55 net: dsa: Add Vitesse VSC73xx DSA router driver
This adds a DSA driver for:

Vitesse VSC7385 SparX-G5 5-port Integrated Gigabit Ethernet Switch
Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch

These switches have a built-in 8051 CPU and can download and execute
firmware in this CPU. They can also be configured to use an external
CPU handling the switch in a memory-mapped manner by connecting to
that external CPU's memory bus.

This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. The chip has embedded PHYs and VLAN support so we model it
using DSA as a best fit so we can easily add VLAN support and maybe
later also exploit the internal frame header to get more direct
control over the switch.

The four built-in GPIO lines are exposed using a standard GPIO chip.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04 11:30:02 +09:00
Florian Fainelli 2a93c1a365 net: dsa: Allow compiling out legacy support
Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-07 14:14:54 -05:00
Woojung Huh b987e98e50 dsa: add DSA switch driver for Microchip KSZ9477
The KSZ9477 is a fully integrated layer 2, managed, 7 ports GigE switch
with numerous advanced features. 5 ports incorporate 10/100/1000 Mbps PHYs.
The other 2 ports have interfaces that can be configured as SGMII, RGMII, MII
or RMII. Either of these may connect directly to a host processor or
to an external PHY. The SGMII port may interface to a fiber optic transceiver.

This driver currently supports vlan, fdb, mdb & mirror dsa switch operations.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-31 20:56:31 -04:00
Andrew Lunn ec34e93f99 drivers: net: DSA: Sort drivers
With more drivers being added, it is time to sort the drivers to
impose some order.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-17 15:19:40 -04:00
Arnd Bergmann 239c599a5f net: dsa: LAN9303: add I2C dependency
With CONFIG_I2C=m and NET_DSA_SMSC_LAN9303=y, we run into a link error:

drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_byte_reg_read':
regmap-i2c.c:(.text.regmap_smbus_byte_reg_read+0x18): undefined reference to `i2c_smbus_read_byte_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_byte_reg_write':
regmap-i2c.c:(.text.regmap_smbus_byte_reg_write+0x18): undefined reference to `i2c_smbus_write_byte_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_reg_read':
regmap-i2c.c:(.text.regmap_smbus_word_reg_read+0x18): undefined reference to `i2c_smbus_read_word_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_read_swapped':
regmap-i2c.c:(.text.regmap_smbus_word_read_swapped+0x18): undefined reference to `i2c_smbus_read_word_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_write_swapped':

This adds a Kconfig dependency to avoid the broken configuration.

Fixes: be4e119f99 ("net: dsa: LAN9303: add I2C managed mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-21 15:33:55 -04:00
Juergen Beisert dc70058315 net: dsa: LAN9303: add MDIO managed mode support
When the LAN9303 device is in MDIO manged mode, all register accesses must
be done via MDIO.

Please note: this code is compile time tested only due to the absence of such
configured hardware. It is based on a patch from Stefan Roese from 2014.

Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
CC: sr@denx.de
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-20 13:48:55 -04:00
Juergen Beisert be4e119f99 net: dsa: LAN9303: add I2C managed mode support
In this mode the switch device and the internal phys will be managed via
I2C interface. The MDIO interface is still supported, but for the
(emulated) CPU port only.

Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
CC: devicetree@vger.kernel.org
CC: robh+dt@kernel.org
CC: mark.rutland@arm.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-20 13:48:54 -04:00
Sean Wang b8f126a8d5 net-next: dsa: add dsa support for Mediatek MT7530 switch
MT7530 is a 7-ports Gigabit Ethernet Switch that could be found on
Mediatek router platforms such as MT7623A or MT7623N platform which
includes 7-port Gigabit Ethernet MAC and 5-port Gigabit Ethernet PHY.
Among these ports, The port from 0 to 4 are the user ports connecting
with the remote devices while the port 5 and 6 are the CPU ports
connecting into Mediatek Ethernet GMAC.

For port 6, it can communicate with the CPU via Mediatek Ethernet GMAC
through either the TRGMII or RGMII which could be controlled by phy-mode
in the dt-bindings to specify which mode is preferred to use. And for
port 5, only RGMII can be specified. However, currently, only port 6 is
being supported in this DSA driver.

The driver is made with the reference to qca8k and other existing DSA
driver. The most of the essential callbacks of the DSA are already
support in the driver, including tag insert for user port distinguishing,
port control, bridge offloading, STP setup and ethtool operation to allow
DSA to model each user port into a standalone netdevice as the other DSA
driver had done.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-07 13:52:11 -07:00
Florian Fainelli 98cd1552ea net: dsa: Mock-up driver
This patch adds support for a DSA mock-up driver which essentially does
the following:

- registers/unregisters 4 fixed PHYs to the slave network devices
- uses eth0 (configurable) as the master netdev
- registers the switch as a fixed MDIO device against the fixed MDIO bus
  at address 31
- includes dynamic debug prints for dsa_switch_ops functions that can be
  enabled to get call traces

This is a good way to test modular builds as well as exercise the DSA
APIs without requiring access to real hardware. This does not test the
data-path, although this could be added later on.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-01 12:39:32 -07:00
Florian Fainelli 68e498554f net: dsa: bcm_sf2: Add missing OF_MDIO dependency
bcm_sf2 does require the MDIO_BCM_UNIMAC driver which is now dependent
on OF_MDIO but also internally uses of_mdio.c provided routines which
are guarted with OF_MDIO.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-24 15:03:06 -07:00
John Crispin 6b93fb4648 net-next: dsa: add new driver for qca8xxx family
This patch contains initial support for the QCA8337 switch. It
will detect a QCA8337 switch, if present and declared in the DT.

Each port will be represented through a standalone net_device interface,
as for other DSA switches. CPU can communicate with any of the ports by
setting an IP@ on ethN interface. Most of the extra callbacks of the DSA
subsystem are already supported, such as bridge offloading, stp, fdb.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-16 04:31:51 -04:00
Florian Fainelli f458995b9a net: dsa: bcm_sf2: Utilize core B53 driver when possible
The Broadcom Starfighter2 is almost entirely register compatible with
B53, yet for historical reasons came up first in the tree and is now
being updated to utilize b53_common.c to the fullest extent possible. A
few things need to be adjusted to allow that:

- the switch "core" registers currently operate on a 32-bit address,
  whereas b53 passes a page + reg pair to offset from, so we need to
  convert that, thankfully there is a generic formula to do that

- the link managemenent is not self contained with the B53/CORE register
  set, but instead is in the SWITCH_REG block which is part of the
  integration glue logic, so we keep that entirely custom here because
  this really is part of the existing bcm_sf2 implementation

- there are additional power management constraints on the port's
  memories that make us keep the port_enable/disable callbacks custom
  for now, also, we support tagging whereas b53_common does not support
  that yet

All the VLAN and bridge code is entirely identical though so, avoid
duplicating it. Other things will be migrated in the future like EEE and
possibly Wake-on-LAN.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-26 13:15:48 -07:00
Vivien Didelot 0d3cd4b6b4 net: dsa: mv88e6xxx: move driver in its own folder
With the upcoming support for cross-chip operations and other mv88e6xxx
enhancements, new files will be added.

Similarly to mlxsw or b53, move mv88e6xxx files into their own folder.

In the meantime, update the MAINTAINERS entry to please checkpatch.pl,
by replacing the invalid 88E6352 entry with 88E6XXX, maintained by
Andrew and myself.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-25 11:29:47 -04:00
Florian Fainelli 967dd82ffc net: dsa: b53: Add support for Broadcom RoboSwitch
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.

This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).

Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-09 22:21:29 -07:00
Vivien Didelot f81ec90fe9 net: dsa: mv88e6xxx: factorize the switch driver
Now that all drivers support the same set of functions and the same
setup code, drop every model-specific DSA switch driver and replace them
with a common mv88e6xxx driver.

This merges the info tables into one, removes the function exports, the
model-specific files, and update the defconfigs.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-09 14:26:13 -04:00
Vivien Didelot b9729e53ad net: dsa: mv88e6131: use EDSA tag protocol
6131 is the only driver to set the tag protocol to DSA_TAG_PROTO_DSA.
Since it works fine with DSA_TAG_PROTO_EDSA, change its value, like all
other mv88e6xxx drivers.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-09 14:26:13 -04:00
Vivien Didelot 8c9983a224 net: dsa: mv88e6xxx: factorize PHY access with PPU
Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.

Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.

Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-09 14:26:08 -04:00
Andrew Lunn ca3dfa51e6 dsa: Rename mv88e6123_61_65 to mv88e6123 to be consistent
All the drivers support multiple chips, but mv88e6123_61_65 is the
only one that reflects this in its naming. Change it to be consistent
with the other drivers.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-14 15:43:10 -04:00
Aleksey S. Kazantsev 7c3d0d67d5 dsa: mv88e6352/mv88e6xxx: Add support for Marvell 88E6320 and 88E6321
MV88E6320 and MV88E6321 are largely compatible to MV886352,
but are members of a different chip family.

Signed-off-by: Aleksey S. Kazantsev <ioctl@yandex.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-09 14:34:23 -07:00
Andrew Lunn eee7483edb net: dsa: mv88e6171: Add other members of the family
The 6171 is one member of the family 6171/6175/6350/6351. Add the
other family members to the driver.

Not tested on these new devices.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-09 16:05:53 -04:00
Andrew Lunn 1636d88357 net: dsa: Move mv88e6172 support into mv88e6352 family driver
The mv88e6172 is part of the mv88e6352 family of devices. Move support
for it out of the mv88e6171 driver into the mv88e6352, which results
in some simplifications to the code.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-09 16:05:53 -04:00
Jiri Pirko bd76a11670 dsa: change "select" to "depends on" for NET_SWITCHDEV and for NET_DSA
This would fix randconfig compile error:
net/built-in.o: In function `netdev_switch_fib_ipv4_abort':
(.text+0xf7811): undefined reference to `fib_flush_external'

Also it fixes following warnings:
warning: (NET_DSA) selects NET_SWITCHDEV which has unmet direct dependencies (NET && INET)

warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6131 && NET_DSA_MV88E6123_61_65 && NET_DSA_MV88E6171 && NET_DSA_MV88E6352 && NET_DSA_BCM_SF2) selects NET_DSA which has unmet direct dependencies (NET && HAVE_NET_DSA && NET_SWITCHDEV)

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-16 16:29:18 -04:00
Florian Fainelli 9f9f26475c net: dsa: bcm_sf2: always select FIXED_PHY
There is no need to do the following:

select FIXED_PHY if NET_DSA_BCM_SF2=y, as this implies that we will not be
able to build and/or run the driver correctly when built as a module,
which is no longer an issue since commit 37e9a69045 ("net: phy: export
fixed_phy_register()").

Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-16 00:57:07 -05:00
Andrew Lunn f03ae5f9c8 dsa: mv88e6171: Add support for mv88e6172
The mv88e6172 is very similar to the mv88e6171.  So extend the
mv88e6171 driver to support it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-06 15:08:05 -05:00
Guenter Roeck 2716777b4f net: dsa/mv88e6352: Add support for MV88E6176
MV88E6176 is mostly compatible to MV88E6352 and is documented
in the same functional specification. Add support for it.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 14:54:10 -04:00
Guenter Roeck 3ad50cca39 net: dsa: Add support for Marvell 88E6352
Marvell 88E6352 is mostly compatible to MV88E6123/61/65,
but requires indirect phy access. Also, its configuration
registers are a bit different.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 14:54:10 -04:00
Chen Gang 28b5533a6f drivers/net/dsa/Kconfig: Let NET_DSA_BCM_SF2 depend on HAS_IOMEM
NET_DSA_BCM_SF2 need HAS_IOMEM, so depend on it, the related error (with
allmodconfig under um):

    CC [M]  drivers/net/dsa/bcm_sf2.o
  drivers/net/dsa/bcm_sf2.c: In function ‘bcm_sf2_sw_setup’:
  drivers/net/dsa/bcm_sf2.c:487:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
     iounmap(*base);
     ^

Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-03 15:52:04 -07:00
Andrew Lunn 42f2725394 net: DSA: Marvell mv88e6171 switch driver
This is the Marvell driver with some cleanups by Claudio Leite
and myself.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Claudio Leite <leitec@staticky.com>
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13 17:26:47 -04:00
Florian Fainelli 246d7f773c net: dsa: add Broadcom SF2 switch driver
Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:

- configuration of the external switch port interface: MII, RevMII,
  RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
  unused

Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-27 22:59:40 -07:00
Ben Hutchings b3422a314c dsa: Hide core config options; make drivers select what they need
Commit 82167cb8c6 ('net: dsa/slave: Fix
compilation warnings') fixed one possible invalid configuration
(NET_DSA enabled with no trailer formats) but added others: drivers
can select NET_DSA without its dependencies being met.

It's not very useful to make either the DSA core or the tagging
formats manually selectable without a driver to use them, so:

1. Define a hidden HAVE_NET_DSA option and move the dependencies of
   NET_DSA to that.  While we're at it, drop the deprecated
   EXPERIMENTAL dependency.
2. Make NET_DSA and the drivers dependent on HAVE_NET_DSA.
3. Hide the tagging format options again.
4. Make drivers select both NET_DSA and the appropriate tagging format
   option.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-26 17:10:44 -05:00
viresh kumar 82167cb8c6 net: dsa/slave: Fix compilation warnings
Currently when none of CONFIG_NET_DSA_TAG_DSA, CONFIG_NET_DSA_TAG_EDSA and
CONFIG_NET_DSA_TAG_TRAILER is defined, we get following compilation warnings:

net/dsa/slave.c:51:12: warning: 'dsa_slave_init' defined but not used [-Wunused-function]
net/dsa/slave.c:60:12: warning: 'dsa_slave_open' defined but not used [-Wunused-function]
net/dsa/slave.c:98:12: warning: 'dsa_slave_close' defined but not used [-Wunused-function]
net/dsa/slave.c:116:13: warning: 'dsa_slave_change_rx_flags' defined but not used [-Wunused-function]
net/dsa/slave.c:127:13: warning: 'dsa_slave_set_rx_mode' defined but not used [-Wunused-function]
net/dsa/slave.c:136:12: warning: 'dsa_slave_set_mac_address' defined but not used [-Wunused-function]
net/dsa/slave.c:164:12: warning: 'dsa_slave_ioctl' defined but not used [-Wunused-function]

Earlier approach to fix this was discussed here:

lkml.org/lkml/2012/10/29/549

This is another approach to fix it. This is done by some changes in config
options, which make more sense than the earlier approach. As, atleast one
tagging option must always be selected for using net/dsa/ infrastructure, this
patch selects NET_DSA from tagging configs instead of having it as an selectable
config.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-25 16:11:47 -05:00
Ben Hutchings 3b15885930 dsa: Move switch drivers to new directory drivers/net/dsa
Support for specific hardware belongs under drivers/net/ not net/.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-29 00:21:36 -05:00