Flushing system-wide workqueues is dangerous and will be forbidden.
Use a local workqueue in dm-mpath.c, dm-raid1.c, and dm-stripe.c.
Link: https://lkml.kernel.org/r/49925af7-78a8-a3dd-bce6-cfc02e1a9236@I-love.SAKURA.ne.jp
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
'GPL-2.0-only' is used instead of 'GPL-2.0' because SPDX has
deprecated its use.
Suggested-by: John Wiele <jwiele@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Introduce dax_recovery_write() operation. The function is used to
recover a dax range that contains poison. Typical use case is when
a user process receives a SIGBUS with si_code BUS_MCEERR_AR
indicating poison(s) in a dax range, in response, the user process
issues a pwrite() to the page-aligned dax range, thus clears the
poison and puts valid data in the range.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Link: https://lore.kernel.org/r/20220422224508.440670-6-jane.chu@oracle.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Up till now, dax_direct_access() is used implicitly for normal
access, but for the purpose of recovery write, dax range with
poison is requested. To make the interface clear, introduce
enum dax_access_mode {
DAX_ACCESS,
DAX_RECOVERY_WRITE,
}
where DAX_ACCESS is used for normal dax access, and
DAX_RECOVERY_WRITE is used for dax recovery write.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Vivek Goyal <vgoyal@redhat.com>
Link: https://lore.kernel.org/r/165247982851.52965.11024212198889762949.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are no more end-users of REQ_OP_WRITE_SAME left, so we can start
deleting it.
Link: https://lore.kernel.org/r/20220209082828.2629273-7-hch@lst.de
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These methods indirect the actual DAX read/write path. In the end pmem
uses magic flush and mc safe variants and fuse and dcssblk use plain ones
while device mapper picks redirects to the underlying device.
Add set_dax_nocache() and set_dax_nomc() APIs to control which copy
routines are used to remove indirect call from the read/write fast path
as well as a lot of boilerplate code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Vivek Goyal <vgoyal@redhat.com> [virtiofs]
Link: https://lore.kernel.org/r/20211215084508.435401-5-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a helper to perform the entire remapping for DAX accesses. This
helper open codes bdev_dax_pgoff given that the alignment checks have
already been done by the submitting file system and don't need to be
repeated.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20211129102203.2243509-12-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The device mapper DAX support is all hanging off a block device and thus
can't be used with device dax. Make it depend on CONFIG_FS_DAX instead
of CONFIG_DAX_DRIVER. This also means that bdev_dax_pgoff only needs to
be built under CONFIG_FS_DAX now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Link: https://lore.kernel.org/r/20211129102203.2243509-3-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For device mapper targets to take advantage of IMA's measurement
capabilities, the status functions for the individual targets need to be
updated to handle the status_type_t case for value STATUSTYPE_IMA.
Update status functions for the following target types, to log their
respective attributes to be measured using IMA.
01. cache
02. crypt
03. integrity
04. linear
05. mirror
06. multipath
07. raid
08. snapshot
09. striped
10. verity
For rest of the targets, handle the STATUSTYPE_IMA case by setting the
measurement buffer to NULL.
For IMA to measure the data on a given system, the IMA policy on the
system needs to be updated to have the following line, and the system
needs to be restarted for the measurements to take effect.
/etc/ima/ima-policy
measure func=CRITICAL_DATA label=device-mapper template=ima-buf
The measurements will be reflected in the IMA logs, which are located at:
/sys/kernel/security/integrity/ima/ascii_runtime_measurements
/sys/kernel/security/integrity/ima/binary_runtime_measurements
These IMA logs can later be consumed by various attestation clients
running on the system, and send them to external services for attesting
the system.
The DM target data measured by IMA subsystem can alternatively
be queried from userspace by setting DM_IMA_MEASUREMENT_FLAG with
DM_TABLE_STATUS_CMD.
Signed-off-by: Tushar Sugandhi <tusharsu@linux.microsoft.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
commit 021a24460d ("block: add QUEUE_FLAG_NOWAIT") added a new queue
flag QUEUE_FLAG_NOWAIT to advertise if the bdev supports handling of
REQ_NOWAIT or not. DM core supports stacking QUEUE_FLAG_NOWAIT since
commit 6abc49468e ("dm: add support for REQ_NOWAIT and enable it for
linear target"), in which only dm-linear enabled it.
Update others DM targets, which just do simple remapping, to enable
support for REQ_NOWAIT.
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch adds support for dax zero_page_range operation to dm targets.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Link: https://lore.kernel.org/r/20200228163456.1587-5-vgoyal@redhat.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct stripe_c {
...
struct stripe stripe[0];
};
In this case alloc_context() and dm_array_too_big() are removed and
replaced by the direct use of the struct_size() helper in kmalloc().
Notice that open-coded form is prone to type mistakes.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Similar to the ->copy_from_iter() operation, a platform may want to
deploy an architecture or device specific routine for handling reads
from a dax_device like /dev/pmemX. On x86 this routine will point to a
machine check safe version of copy_to_iter(). For now, add the plumbing
to device-mapper and the dax core.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* A rework of the filesytem-dax implementation provides for detection of
unmap operations (truncate / hole punch) colliding with in-progress
device-DMA. A fix for these collisions remains a work-in-progress
pending resolution of truncate latency and starvation regressions.
* The of_pmem driver expands the users of libnvdimm outside of x86 and
ACPI to describe an implementation of persistent memory on PowerPC with
Open Firmware / Device tree.
* Address Range Scrub (ARS) handling is completely rewritten to account for
the fact that ARS may run for 100s of seconds and there is no platform
defined way to cancel it. ARS will now no longer block namespace
initialization.
* The NVDIMM Namespace Label implementation is updated to handle label
areas as small as 1K, down from 128K.
* Miscellaneous cleanups and updates to unit test infrastructure.
-----BEGIN PGP SIGNATURE-----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=acZQ
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This cycle was was not something I ever want to repeat as there were
several late changes that have only now just settled.
Half of the branch up to commit d2c997c0f1 ("fs, dax: use
page->mapping to warn...") have been in -next for several releases.
The of_pmem driver and the address range scrub rework were late
arrivals, and the dax work was scaled back at the last moment.
The of_pmem driver missed a previous merge window due to an oversight.
A sense of obligation to rectify that miss is why it is included for
4.17. It has acks from PowerPC folks. Stephen reported a build failure
that only occurs when merging it with your latest tree, for now I have
fixed that up by disabling modular builds of of_pmem. A test merge
with your tree has received a build success report from the 0day robot
over 156 configs.
An initial version of the ARS rework was submitted before the merge
window. It is self contained to libnvdimm, a net code reduction, and
passing all unit tests.
The filesystem-dax changes are based on the wait_var_event()
functionality from tip/sched/core. However, late review feedback
showed that those changes regressed truncate performance to a large
degree. The branch was rewound to drop the truncate behavior change
and now only includes preparation patches and cleanups (with full acks
and reviews). The finalization of this dax-dma-vs-trnucate work will
need to wait for 4.18.
Summary:
- A rework of the filesytem-dax implementation provides for detection
of unmap operations (truncate / hole punch) colliding with
in-progress device-DMA. A fix for these collisions remains a
work-in-progress pending resolution of truncate latency and
starvation regressions.
- The of_pmem driver expands the users of libnvdimm outside of x86
and ACPI to describe an implementation of persistent memory on
PowerPC with Open Firmware / Device tree.
- Address Range Scrub (ARS) handling is completely rewritten to
account for the fact that ARS may run for 100s of seconds and there
is no platform defined way to cancel it. ARS will now no longer
block namespace initialization.
- The NVDIMM Namespace Label implementation is updated to handle
label areas as small as 1K, down from 128K.
- Miscellaneous cleanups and updates to unit test infrastructure"
* tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (39 commits)
libnvdimm, of_pmem: workaround OF_NUMA=n build error
nfit, address-range-scrub: add module option to skip initial ars
nfit, address-range-scrub: rework and simplify ARS state machine
nfit, address-range-scrub: determine one platform max_ars value
powerpc/powernv: Create platform devs for nvdimm buses
doc/devicetree: Persistent memory region bindings
libnvdimm: Add device-tree based driver
libnvdimm: Add of_node to region and bus descriptors
libnvdimm, region: quiet region probe
libnvdimm, namespace: use a safe lookup for dimm device name
libnvdimm, dimm: fix dpa reservation vs uninitialized label area
libnvdimm, testing: update the default smart ctrl_temperature
libnvdimm, testing: Add emulation for smart injection commands
nfit, address-range-scrub: introduce nfit_spa->ars_state
libnvdimm: add an api to cast a 'struct nd_region' to its 'struct device'
nfit, address-range-scrub: fix scrub in-progress reporting
dax, dm: allow device-mapper to operate without dax support
dax: introduce CONFIG_DAX_DRIVER
fs, dax: use page->mapping to warn if truncate collides with a busy page
ext2, dax: introduce ext2_dax_aops
...
Set QUEUE_FLAG_SECERASE in DM device's queue_flags if a DM table's
data devices support secure erase.
Also, add support for secure erase to both the linear and striped
targets.
Signed-off-by: Denis Semakin <d.semakin@omprussia.ru>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Ideally, we'd like to get rid of all VLAs in the kernel and add -Wvla to
the build args: https://lkml.org/lkml/2018/3/7/621
This one is a simple case, since we don't actually need the VLA at all: we
can just iterate over the stripes twice, once to emit their names, and the
second time to emit status (i.e. trade memory for time). Since the number
of stripes is probably low, this is hopefully not that expensive.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Change device-mapper's DAX dependency to require the presence of at
least one DAX_DRIVER. This allows device-mapper to be built without
bringing the DAX core along which is especially wasteful when there are
no DAX drivers, like BLK_DEV_PMEM, configured.
Cc: Alasdair Kergon <agk@redhat.com>
Reported-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush abstraction
that was stood up for DM's use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZuo8UAAoJEMUj8QotnQNa5BEIANO4mHh1nrzEbH72a4RCLgxV
H1Pk1zZx/W1bhOOmcRRhxCSM85dPgsCegc5EmpwLZEMavQrP9UZblHcYOUsyIx7W
S/lWa+soOq/5N2OveROc4WdoWVs50UFmc1+BcClc4YrEe+15XC3R0VMkjX2b/hUL
o2eYhPjpMlgaorMtRRU6MAooo2fBRQ9m05aPeVgd35fxibrE7PZm+EYW09wa0STi
9ufuDXJf8+TtFP/38BD41LbUEskuHUZTSDeAJ+3DBaTtfEZcZYxsst4P9JangsHx
jqqqI9aYzFD2a27fl9WLhCvm40YFiKp5nwzED0RZjzWxVa/jTShX7a49BdzTTfw=
=rkSB
-----END PGP SIGNATURE-----
Merge tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Some request-based DM core and DM multipath fixes and cleanups
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM
integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush
abstraction that was stood up for DM's use.
* tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dax: remove the pmem_dax_ops->flush abstraction
dm integrity: use init_completion instead of COMPLETION_INITIALIZER_ONSTACK
dm integrity: make blk_integrity_profile structure const
dm integrity: do not check integrity for failed read operations
dm log writes: fix >512b sectorsize support
dm log writes: don't use all the cpu while waiting to log blocks
dm ioctl: constify ioctl lookup table
dm: constify argument arrays
dm integrity: count and display checksum failures
dm integrity: optimize writing dm-bufio buffers that are partially changed
dm rq: do not update rq partially in each ending bio
dm rq: make dm-sq requeuing behavior consistent with dm-mq behavior
dm mpath: complain about unsupported __multipath_map_bio() return values
dm mpath: avoid that building with W=1 causes gcc 7 to complain about fall-through
Commit abebfbe2f7 ("dm: add ->flush() dax operation support") is
buggy. A DM device may be composed of multiple underlying devices and
all of them need to be flushed. That commit just routes the flush
request to the first device and ignores the other devices.
It could be fixed by adding more complex logic to the device mapper. But
there is only one implementation of the method pmem_dax_ops->flush - that
is pmem_dax_flush() - and it calls arch_wb_cache_pmem(). Consequently, we
don't need the pmem_dax_ops->flush abstraction at all, we can call
arch_wb_cache_pmem() directly from dax_flush() because dax_dev->ops->flush
can't ever reach anything different from arch_wb_cache_pmem().
It should be also pointed out that for some uses of persistent memory it
is needed to flush only a very small amount of data (such as 1 cacheline),
and it would be overkill if we go through that device mapper machinery for
a single flushed cache line.
Fix this by removing the pmem_dax_ops->flush abstraction and call
arch_wb_cache_pmem() directly from dax_flush(). Also, remove the device
mapper code that forwards the flushes.
Fixes: abebfbe2f7 ("dm: add ->flush() dax operation support")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Introduce the _flushcache() family of memory copy helpers and use them
for persistent memory write operations on x86. The _flushcache()
semantic indicates that the cache is either bypassed for the copy
operation (movnt) or any lines dirtied by the copy operation are
written back (clwb, clflushopt, or clflush).
* Extend dax_operations with ->copy_from_iter() and ->flush()
operations. These operations and other infrastructure updates allow
all persistent memory specific dax functionality to be pushed into
libnvdimm and the pmem driver directly. It also allows dax-specific
sysfs attributes to be linked to a host device, for example:
/sys/block/pmem0/dax/write_cache
* Add support for the new NVDIMM platform/firmware mechanisms introduced
in ACPI 6.2 and UEFI 2.7. This support includes the v1.2 namespace
label format, extensions to the address-range-scrub command set, new
error injection commands, and a new BTT (block-translation-table)
layout. These updates support inter-OS and pre-OS compatibility.
* Fix a longstanding memory corruption bug in nfit_test.
* Make the pmem and nvdimm-region 'badblocks' sysfs files poll(2)
capable.
* Miscellaneous fixes and small updates across libnvdimm and the nfit
driver.
Acknowledgements that came after the branch was pushed:
commit 6aa734a2f3 "libnvdimm, region, pmem: fix 'badblocks'
sysfs_get_dirent() reference lifetime"
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
-----BEGIN PGP SIGNATURE-----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=xKQB
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"libnvdimm updates for the latest ACPI and UEFI specifications. This
pull request also includes new 'struct dax_operations' enabling to
undo the abuse of copy_user_nocache() for copy operations to pmem.
The dax work originally missed 4.12 to address concerns raised by Al.
Summary:
- Introduce the _flushcache() family of memory copy helpers and use
them for persistent memory write operations on x86. The
_flushcache() semantic indicates that the cache is either bypassed
for the copy operation (movnt) or any lines dirtied by the copy
operation are written back (clwb, clflushopt, or clflush).
- Extend dax_operations with ->copy_from_iter() and ->flush()
operations. These operations and other infrastructure updates allow
all persistent memory specific dax functionality to be pushed into
libnvdimm and the pmem driver directly. It also allows dax-specific
sysfs attributes to be linked to a host device, for example:
/sys/block/pmem0/dax/write_cache
- Add support for the new NVDIMM platform/firmware mechanisms
introduced in ACPI 6.2 and UEFI 2.7. This support includes the v1.2
namespace label format, extensions to the address-range-scrub
command set, new error injection commands, and a new BTT
(block-translation-table) layout. These updates support inter-OS
and pre-OS compatibility.
- Fix a longstanding memory corruption bug in nfit_test.
- Make the pmem and nvdimm-region 'badblocks' sysfs files poll(2)
capable.
- Miscellaneous fixes and small updates across libnvdimm and the nfit
driver.
Acknowledgements that came after the branch was pushed: commit
6aa734a2f3 ("libnvdimm, region, pmem: fix 'badblocks'
sysfs_get_dirent() reference lifetime") was reviewed by Toshi Kani
<toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (42 commits)
libnvdimm, namespace: record 'lbasize' for pmem namespaces
acpi/nfit: Issue Start ARS to retrieve existing records
libnvdimm: New ACPI 6.2 DSM functions
acpi, nfit: Show bus_dsm_mask in sysfs
libnvdimm, acpi, nfit: Add bus level dsm mask for pass thru.
acpi, nfit: Enable DSM pass thru for root functions.
libnvdimm: passthru functions clear to send
libnvdimm, btt: convert some info messages to warn/err
libnvdimm, region, pmem: fix 'badblocks' sysfs_get_dirent() reference lifetime
libnvdimm: fix the clear-error check in nsio_rw_bytes
libnvdimm, btt: fix btt_rw_page not returning errors
acpi, nfit: quiet invalid block-aperture-region warnings
libnvdimm, btt: BTT updates for UEFI 2.7 format
acpi, nfit: constify *_attribute_group
libnvdimm, pmem: disable dax flushing when pmem is fronting a volatile region
libnvdimm, pmem, dax: export a cache control attribute
dax: convert to bitmask for flags
dax: remove default copy_from_iter fallback
libnvdimm, nfit: enable support for volatile ranges
libnvdimm, pmem: fix persistence warning
...
Allow device-mapper to route flush operations to the
per-target implementation. In order for the device stacking to work we
need a dax_dev and a pgoff relative to that device. This gives each
layer of the stack the information it needs to look up the operation
pointer for the next level.
This conceptually allows for an array of mixed device drivers with
varying flush implementations.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Allow device-mapper to route copy_from_iter operations to the
per-target implementation. In order for the device stacking to work we
need a dax_dev and a pgoff relative to that device. This gives each
layer of the stack the information it needs to look up the operation
pointer for the next level.
This conceptually allows for an array of mixed device drivers with
varying copy_from_iter implementations.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Turn the error paramter into a pointer so that target drivers can change
the value, and make sure only DM_ENDIO_* values are returned from the
methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A few (but not all) dm targets use a special EWOULDBLOCK error code for
failing REQ_RAHEAD requests that fail due to a lack of available resources.
But no one else knows about this magic code, and lower level drivers also
don't generate it when failing read-ahead requests for similar reasons.
So remove this special casing and ignore all additional error handling for
REQ_RAHEAD - if this was a real underlying error we'd get a normal read
once the real read comes in.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
* Region media error reporting: A libnvdimm region device is the parent
to one or more namespaces. To date, media errors have been reported via
the "badblocks" attribute attached to pmem block devices for namespaces
in "raw" or "memory" mode. Given that namespaces can be in "device-dax"
or "btt-sector" mode this new interface reports media errors
generically, i.e. independent of namespace modes or state. This
subsequently allows userspace tooling to craft "ACPI 6.1 Section
9.20.7.6 Function Index 4 - Clear Uncorrectable Error" requests and
submit them via the ioctl path for NVDIMM root bus devices.
* Introduce 'struct dax_device' and 'struct dax_operations': Prompted by
a request from Linus and feedback from Christoph this allows for dax
capable drivers to publish their own custom dax operations. This fixes
the broken assumption that all dax operations are related to a
persistent memory device, and makes it easier for other architectures
and platforms to add customized persistent memory support.
* 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger memory
controllers to drain write-pending buffers that would otherwise be
flushed automatically by the platform ADR (asynchronous-DRAM-refresh)
mechanism at a power loss event. Support for "locked" DIMMs is included
to prevent namespaces from surfacing when the namespace label data area
is locked. Finally, fixes for various reported deadlocks and crashes,
also tagged for -stable.
* ACPI / nfit driver updates: General updates of the nfit driver to add
DSM command overrides, ACPI 6.1 health state flags support, DSM payload
debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
commmit 565851c972 "device-dax: fix sysfs attribute deadlock"
Tested-by: Yi Zhang <yizhan@redhat.com>
commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>
-----BEGIN PGP SIGNATURE-----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=Ox0s
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this has been in multiple -next releases. There were a few
late breaking fixes and small features that got added in the last
couple days, but the whole set has received a build success
notification from the kbuild robot.
Change summary:
- Region media error reporting: A libnvdimm region device is the
parent to one or more namespaces. To date, media errors have been
reported via the "badblocks" attribute attached to pmem block
devices for namespaces in "raw" or "memory" mode. Given that
namespaces can be in "device-dax" or "btt-sector" mode this new
interface reports media errors generically, i.e. independent of
namespace modes or state.
This subsequently allows userspace tooling to craft "ACPI 6.1
Section 9.20.7.6 Function Index 4 - Clear Uncorrectable Error"
requests and submit them via the ioctl path for NVDIMM root bus
devices.
- Introduce 'struct dax_device' and 'struct dax_operations': Prompted
by a request from Linus and feedback from Christoph this allows for
dax capable drivers to publish their own custom dax operations.
This fixes the broken assumption that all dax operations are
related to a persistent memory device, and makes it easier for
other architectures and platforms to add customized persistent
memory support.
- 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger
memory controllers to drain write-pending buffers that would
otherwise be flushed automatically by the platform ADR
(asynchronous-DRAM-refresh) mechanism at a power loss event.
Support for "locked" DIMMs is included to prevent namespaces from
surfacing when the namespace label data area is locked. Finally,
fixes for various reported deadlocks and crashes, also tagged for
-stable.
- ACPI / nfit driver updates: General updates of the nfit driver to
add DSM command overrides, ACPI 6.1 health state flags support, DSM
payload debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
- commmit 565851c972 "device-dax: fix sysfs attribute deadlock":
Tested-by: Yi Zhang <yizhan@redhat.com>
- commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (52 commits)
libnvdimm, pfn: fix 'npfns' vs section alignment
libnvdimm: handle locked label storage areas
libnvdimm: convert NDD_ flags to use bitops, introduce NDD_LOCKED
brd: fix uninitialized use of brd->dax_dev
block, dax: use correct format string in bdev_dax_supported
device-dax: fix sysfs attribute deadlock
libnvdimm: restore "libnvdimm: band aid btt vs clear poison locking"
libnvdimm: fix nvdimm_bus_lock() vs device_lock() ordering
libnvdimm: rework region badblocks clearing
acpi, nfit: kill ACPI_NFIT_DEBUG
libnvdimm: fix clear length of nvdimm_forget_poison()
libnvdimm, pmem: fix a NULL pointer BUG in nd_pmem_notify
libnvdimm, region: sysfs trigger for nvdimm_flush()
libnvdimm: fix phys_addr for nvdimm_clear_poison
x86, dax, pmem: remove indirection around memcpy_from_pmem()
block: remove block_device_operations ->direct_access()
block, dax: convert bdev_dax_supported() to dax_direct_access()
filesystem-dax: convert to dax_direct_access()
Revert "block: use DAX for partition table reads"
ext2, ext4, xfs: retrieve dax_device for iomap operations
...
whether blocks should migrate to/from the cache. The bio-prison-v2
interface supports this improvement by enabling direct dispatch of
work to workqueues rather than having to delay the actual work
dispatch to the DM cache core. So the dm-cache policies are much more
nimble by being able to drive IO as they see fit. One immediate
benefit from the improved latency is a cache that should be much more
adaptive to changing workloads.
- Add a new DM integrity target that emulates a block device that has
additional per-sector tags that can be used for storing integrity
information.
- Add a new authenticated encryption feature to the DM crypt target that
builds on the capabilities provided by the DM integrity target.
- Add MD interface for switching the raid4/5/6 journal mode and update
the DM raid target to use it to enable aid4/5/6 journal write-back
support.
- Switch the DM verity target over to using the asynchronous hash crypto
API (this helps work better with architectures that have access to
off-CPU algorithm providers, which should reduce CPU utilization).
- Various request-based DM and DM multipath fixes and improvements from
Bart and Christoph.
- A DM thinp target fix for a bio structure leak that occurs for each
discard IFF discard passdown is enabled.
- A fix for a possible deadlock in DM bufio and a fix to re-check the
new buffer allocation watermark in the face of competing admin changes
to the 'max_cache_size_bytes' tunable.
- A couple DM core cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZB6vtAAoJEMUj8QotnQNaoicIALuZTLElgAzxzA28cfk1+1Ea
Gd09CfJ3M6cvk/YGUU7WwiSYIwu16yOJALG4sLcYnEmUCzvKfFPcl/RpeSJHPpYM
0aVXa6NIJw7K2r3C17toiK2DRMHYw6QU843WeWI93vBW13lDJklNJL9fM7GBEOLH
NMSNw2mAq9ajtLlnJhM3ZfhloA7/u/jektvlBO1AA3RQ5Kx1cXVXFPqN7FdRfcqp
4RuEMe9faAadlXLsj3bia5IBmF/W0Qza6JilP+NLKLWB4fm7LZDjN/k+TsHWMa9e
cGR73TgUGLMBJX+sDJy8R3oeBG9JZkFVkD7I30eCjzyhSOs/54XNYQ23EkqHJU0=
=9Ryi
-----END PGP SIGNATURE-----
Merge tag 'for-4.12/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- A major update for DM cache that reduces the latency for deciding
whether blocks should migrate to/from the cache. The bio-prison-v2
interface supports this improvement by enabling direct dispatch of
work to workqueues rather than having to delay the actual work
dispatch to the DM cache core. So the dm-cache policies are much more
nimble by being able to drive IO as they see fit. One immediate
benefit from the improved latency is a cache that should be much more
adaptive to changing workloads.
- Add a new DM integrity target that emulates a block device that has
additional per-sector tags that can be used for storing integrity
information.
- Add a new authenticated encryption feature to the DM crypt target
that builds on the capabilities provided by the DM integrity target.
- Add MD interface for switching the raid4/5/6 journal mode and update
the DM raid target to use it to enable aid4/5/6 journal write-back
support.
- Switch the DM verity target over to using the asynchronous hash
crypto API (this helps work better with architectures that have
access to off-CPU algorithm providers, which should reduce CPU
utilization).
- Various request-based DM and DM multipath fixes and improvements from
Bart and Christoph.
- A DM thinp target fix for a bio structure leak that occurs for each
discard IFF discard passdown is enabled.
- A fix for a possible deadlock in DM bufio and a fix to re-check the
new buffer allocation watermark in the face of competing admin
changes to the 'max_cache_size_bytes' tunable.
- A couple DM core cleanups.
* tag 'for-4.12/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (50 commits)
dm bufio: check new buffer allocation watermark every 30 seconds
dm bufio: avoid a possible ABBA deadlock
dm mpath: make it easier to detect unintended I/O request flushes
dm mpath: cleanup QUEUE_IF_NO_PATH bit manipulation by introducing assign_bit()
dm mpath: micro-optimize the hot path relative to MPATHF_QUEUE_IF_NO_PATH
dm: introduce enum dm_queue_mode to cleanup related code
dm mpath: verify __pg_init_all_paths locking assumptions at runtime
dm: verify suspend_locking assumptions at runtime
dm block manager: remove an unused argument from dm_block_manager_create()
dm rq: check blk_mq_register_dev() return value in dm_mq_init_request_queue()
dm mpath: delay requeuing while path initialization is in progress
dm mpath: avoid that path removal can trigger an infinite loop
dm mpath: split and rename activate_path() to prepare for its expanded use
dm ioctl: prevent stack leak in dm ioctl call
dm integrity: use previously calculated log2 of sectors_per_block
dm integrity: use hex2bin instead of open-coded variant
dm crypt: replace custom implementation of hex2bin()
dm crypt: remove obsolete references to per-CPU state
dm verity: switch to using asynchronous hash crypto API
dm crypt: use WQ_HIGHPRI for the IO and crypt workqueues
...
Arrange for dm to lookup the dax services available from member devices.
Update the dax-capable targets, linear and stripe, to route dax
operations to the underlying device. Changes the target-internal
->direct_access() method to more closely align with the dax_operations
->direct_access() calling convention.
Cc: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A dm-crypt on dm-integrity device incorrectly advertises an integrity
profile on the DM crypt device. It can be seen in the files
"/sys/block/dm-*/integrity/*" that both dm-integrity and dm-crypt target
advertise the integrity profile. That is incorrect, only the
dm-integrity target should advertise the integrity profile.
A general problem in DM is that if we have a DM device that depends on
another device with an integrity profile, the upper device will always
advertise the integrity profile, even when the target driver doesn't
support handling integrity data.
Most targets don't support integrity data, so we provide a whitelist of
targets that support it (linear, delay and striped). The targets that
support passing integrity data to the lower device are marked with the
flag DM_TARGET_PASSES_INTEGRITY. The DM core will now advertise
integrity data on a DM device only if all the targets support the
integrity data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Copy & paste from the REQ_OP_WRITE_SAME code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
1/ Replace pcommit with ADR / directed-flushing:
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement either
ADR, or provide one or more flush addresses per nvdimm. ADR
(Asynchronous DRAM Refresh) flushes data in posted write buffers to the
memory controller on a power-fail event. Flush addresses are defined in
ACPI 6.x as an NVDIMM Firmware Interface Table (NFIT) sub-structure:
"Flush Hint Address Structure". A flush hint is an mmio address that
when written and fenced assures that all previous posted writes
targeting a given dimm have been flushed to media.
2/ On-demand ARS (address range scrub):
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the media
to refresh the bad block list, userspace can also request a re-scrub at
any time.
3/ Support for the Microsoft DSM (device specific method) command format.
4/ Support for EDK2/OVMF virtual disk device memory ranges.
5/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xCBG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
Change dm-stripe to implement direct_access function,
stripe_direct_access(), which maps bdev and sector and
calls direct_access function of its physical target device.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have dm
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull device mapper update from Mike Snitzer:
- a couple small cleanups in dm-cache, dm-verity, persistent-data's
dm-btree, and DM core.
- a 4.1-stable fix for dm-cache that fixes the leaking of deferred bio
prison cells
- a 4.2-stable fix that adds feature reporting for the dm-stats
features added in 4.2
- improve DM-snapshot to not invalidate the on-disk snapshot if
snapshot device write overflow occurs; but a write overflow triggered
through the origin device will still invalidate the snapshot.
- optimize DM-thinp's async discard submission a bit now that late bio
splitting has been included in block core.
- switch DM-cache's SMQ policy lock from using a mutex to a spinlock;
improves performance on very low latency devices (eg. NVMe SSD).
- document DM RAID 4/5/6's discard support
[ I did not pull the slab changes, which weren't appropriate for this
tree, and weren't obviously the right thing to do anyway. At the very
least they need some discussion and explanation before getting merged.
Because not pulling the actual tagged commit but doing a partial pull
instead, this merge commit thus also obviously is missing the git
signature from the original tag ]
* tag 'dm-4.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix use after freeing migrations
dm cache: small cleanups related to deferred prison cell cleanup
dm cache: fix leaking of deferred bio prison cells
dm raid: document RAID 4/5/6 discard support
dm stats: report precise_timestamps and histogram in @stats_list output
dm thin: optimize async discard submission
dm snapshot: don't invalidate on-disk image on snapshot write overflow
dm: remove unlikely() before IS_ERR()
dm: do not override error code returned from dm_get_device()
dm: test return value for DM_MAPIO_SUBMITTED
dm verity: remove unused mempool
dm cache: move wake_waker() from free_migrations() to where it is needed
dm btree remove: remove unused function get_nr_entries()
dm btree: remove unused "dm_block_t root" parameter in btree_split_sibling()
dm cache policy smq: change the mutex to a spinlock
As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
dm-era-target, and resolve merge conflicts]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Some of the device mapper targets override the error code returned by
dm_get_device() and return either -EINVAL or -ENXIO. There is nothing
gained by this override. It is better to propagate the returned error
code unchanged to caller.
This work was motivated by hitting an issue where the underlying device
was busy but -EINVAL was being returned. After this change we get
-EBUSY instead and it is easier to figure out the problem.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix a potential struct stripe_c leak that would occur if the
chunk_size exceeded the maximum allowed by dm_set_target_max_io_len
(UINT_MAX). However, in practice there is no possibility of this
occuring given that chunk_size is of type uint32_t. But it is good to
fix this to future-proof in case dm_set_target_max_io_len's
implementation were to change.
Signed-off-by: Pavitra Kumar <pavitrak@nvidia.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Eliminate the following sparse warnings:
drivers/md/dm-stripe.c:443:12: warning: symbol 'dm_stripe_init' was not declared. Should it be static?
drivers/md/dm-stripe.c:456:6: warning: symbol 'dm_stripe_exit' was not declared. Should it be static?
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>