This patch removes the error checking for debugfs_create_dir
in adm1266.c. This is because the debugfs_create_dir() does not
return NULL but an ERR_PTR after an error.
The DebugFS kernel API is developed in a way that the
caller can safely ignore the errors that occur during
the creation of DebugFS nodes.The debugfs Api handles
it gracefully. The check is unnecessary.
Link to the comment above debugfs_create_dir:
https://elixir.bootlin.com/linux/latest/source/fs/debugfs/inode.c#L565
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Link: https://lore.kernel.org/r/20230526163938.9903-1-osmtendev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch removes the error checking for debugfs_create_dir
in ucd9000.c. This is because the debugfs_create_dir() does not
return NULL but an ERR_PTR after an error.
The DebugFS kernel API is developed in a way that the
caller can safely ignore the errors that occur during
the creation of DebugFS nodes.The debugfs Api handles
it gracefully. The check is unnecessary.
Link to the comment above debugfs_create_dir:
https://elixir.bootlin.com/linux/latest/source/fs/debugfs/inode.c#L565
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Link: https://lore.kernel.org/r/20230526154906.6370-1-osmtendev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking for Kconfig symbols with #if is wrong:
drivers/hwmon/hp-wmi-sensors.c:1141:5: error: "CONFIG_DEBUG_FS" is not defined, evaluates to 0 [-Werror=undef]
This could be an #ifdef, but an IS_ENABLED() check is even better to
give the best compile coverage.
Fixes: 23902f98f8 ("hwmon: add HP WMI Sensors driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230601213216.3220550-1-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hewlett-Packard (and some HP Compaq) business-class computers report
hardware monitoring information via WMI. This driver exposes that
information to hwmon.
Initial support is provided for temperature, fan speed, and intrusion
sensor types. Provisional support is provided for voltage and current
sensor types.
HP's WMI implementation permits many other types of numeric sensors.
Therefore, a debugfs interface is also provided to enumerate and
inspect all numeric sensors visible on the WMI side. This should
facilitate adding support for other sensor types in the future.
Tested on a HP Z420, a HP EliteOne 800 G1, and a HP Compaq Elite 8300
SFF.
Note that provisionally supported sensor types are untested and seem
to be rare-to-nonexistent in the wild, having been encountered
neither on test systems nor in ACPI dumps from the Linux Hardware
Database. They are included because their popularity in general makes
their presence on past or future HP systems plausible and because no
doubt exists as to how the sensors themselves would be represented in
WMI (alarm attributes will need to wait for hardware to be located).
A 2005 HP whitepaper gives the relevant sensor object MOF definition
and sensor value scaling calculation, and both this driver and the
official HP Performance Advisor utility comply with them (confirmed
in the latter case by reverse engineering).
Link: https://h20331.www2.hp.com/hpsub/downloads/cmi_whitepaper.pdf
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230522115645.509701-1-james@equiv.tech
[groeck: Set error return value for intrusion writes to -EINVAL.
Always accept writes of 0 even if there was no intrusion. ]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We don't need to pass device structure to write_to_ec() so we remove
that from the function declaration.
The same is valid for pwm_enable() and pwm_disable() as we were passing
the pointer to hand it off to write_to_ec().
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230525142652.41981-1-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31827 is a low-power temperature switch with I2C interface.
The device is a ±1°C accuracy from -40°C to +125°C
(12 bits) local temperature switch and sensor with I2C/SM-
Bus interface. The combination of small 6-bump wafer-lev-
el package (WLP) and high accuracy makes this temper-
ature sensor/switch ideal for a wide range of applications.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20230524160131.14081-2-daniel.matyas@analog.com
[groeck: Improved define alignment, return -EINVAL after bad user input,
fixed up compatible statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for compatible AHT20 temperature/humidity sensor. The only
difference between the two is that AHT20 has additional crc8 byte.
It seems like AHT15 is also supported by the driver but it wasn't
verified and tested yet.
Tested on Beaglebone black rev C.
Signed-off-by: Kirill Yatsenko <kiriyatsenko@gmail.com>
Link: https://lore.kernel.org/r/20230524201912.815993-1-kiriyatsenko@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A newer BIOS version for the OneXPlayer Mini AMD modified vendor and
board name strings. Add those to the match table and set the same board
model as older OXP Mini AMD.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230517183540.187383-1-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer Leakshield leak prevention system, which communicates
through a proprietary USB HID protocol. Implemented by Noah Bergbauer [1].
Two temperature sensors are exposed, along with pressure (current, min, max
and target), reservoir volume (total and filled), pump speed and flow. Pump
speed and flow values are user provided and allow the Leakshield to
optimize its operation. Writing them to the device is subject of future
patches.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/41
Originally-from: Noah Bergbauer <main@ehvag.de>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230520095447.509287-3-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Exit from the function immediately if the poll time hasn't yet expired.
Therefore the code after the check can be moved one tab to the left which
improves readability.
Signed-off-by: Kirill Yatsenko <kiriyatsenko@gmail.com>
Link: https://lore.kernel.org/r/20230511202633.299174-2-kiriyatsenko@gmail.com
[groeck: Dropped else after return]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix typos in the description of the return value section of the
functions. The word 'succesfull' is incorrect, it should be 'successful'.
Signed-off-by: Kirill Yatsenko <kiriyatsenko@gmail.com>
Link: https://lore.kernel.org/r/20230511202633.299174-1-kiriyatsenko@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 848ba0a2f2 ("hwmon: (core) Rename groups parameter in API to
extra_groups") renames the 'groups' parameter of
devm_hwmon_device_register_with_info() to 'extra_groups' in
hwmon-kernel-api.txt (later .rst) and hwmon.h, but this change was not
propagated to the function code itself in hwmon.c. Finish the job.
Note that hwmon_device_register_with_info() has the same
parameter, and the name of that parameter was changed in all
three files. Harmonizing the name between these related
functions also removes a potential source of confusion.
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230507151051.1861929-1-james@equiv.tech
[groeck: Fixed up SHA reference in description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
beep_enable, inX_beep, currX_beep, fanX_beep, and tempX_beep
are standard attributes mentioned in the sysfs interface
specification but not implemented in the hwmon core. Since
these are not deprecated, implement them.
Adding beep_mask is not necessary, as it is deprecated and
the drivers already using it are manually defining it.
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230507152216.1862653-1-james@equiv.tech
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230505131718.1210071-1-u.kleine-koenig@pengutronix.de
[groeck: Added missing change in pmbus/acbel-fsg032.c]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some chips are known to only have 4 temperature sensors and there is no
requirement to test for more. Currently only the IT8622E fits this
category.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230430045032.1723288-1-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of of_property_read_*() use the equivalent
device_property_read_*() API. This will allow these properties to be
used on DT unaware platforms. For DT aware platforms this will be a
noop.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230418233656.869055-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add feature and support for chips with only 4 fans.
Reorder macro definitions to bring all fan definitions together.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230429115205.1547251-2-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Only the temp sensors that I can verify are present. HWINFO in
Windows shows other accumulated data and statistics (time since
installed, total power used, etc) that I have not attempted to find.
Signed-off-by: Michael Carns <mike@carns.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20230426200345.65765-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for handhelds with same EC registers
- AYANEO 2
- AYANEO GEEK
All functionality tests succeed on AYANEO 2 by "pastaq" user on Discord
and AYANEO GEEK tested by "oneoc" Discord user.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20230426184420.99945-1-samsagax@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PMON_CONFIG register on ADM1272 is a 16 bit register. Writing a 8 bit
value into it clears the upper 8 bits of the register, resulting in
unexpected side effects. Fix by writing the 16 bit register value.
Also, it has been reported that temperature readings are sometimes widely
inaccurate, to the point where readings may result in device shutdown due
to errant overtemperature faults. Improve by enabling temperature sampling.
While at it, move the common code for ADM1272 and ADM1278 into a separate
function, and clarify in the error message that an attempt was made to
enable both VOUT and temperature monitoring.
Last but not least, return the error code reported by the underlying I2C
controller and not -ENODEV if updating the PMON_CONFIG register fails.
After all, this does not indicate that the chip is not present, but an
error in the communication with the chip.
Fixes: 4ff0ce227a ("hwmon: (pmbus/adm1275) Add support for ADM1272")
Fixes: 9da9c2dc57 ("hwmon: (adm1275) enable adm1272 temperature reporting")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230602213447.3557346-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The GSC fan pwm temperature register is in centidegrees celcius but the
Linux hwmon convention is to use milidegrees celcius. Fix the scaling.
Fixes: 3bce5377ef ("hwmon: Add Gateworks System Controller support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://lore.kernel.org/r/20230606153004.1448086-1-tharvey@gateworks.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that it exists, use it instead of doing the multiplication manually.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: James Clark <james.clark@arm.com>
Link: https://lore.kernel.org/r/20230509094942.396150-3-james.clark@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PXA platform has a number of configurations that end up with
a warning like these when building with W=1:
drivers/hwmon/max1111.c:83:5: error: no previous prototype for 'max1111_read_channel' [-Werror=missing-prototypes]
arch/arm/mach-pxa/reset.c:86:6: error: no previous prototype for 'pxa_restart' [-Werror=missing-prototypes]
arch/arm/mach-pxa/mfp-pxa2xx.c:254:5: error: no previous prototype for 'keypad_set_wake' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa25x.c:70:14: error: no previous prototype for 'pxa25x_get_clk_frequency_khz' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa25x.c:325:12: error: no previous prototype for 'pxa25x_clocks_init' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:74:14: error: no previous prototype for 'pxa27x_get_clk_frequency_khz' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:102:6: error: no previous prototype for 'pxa27x_is_ppll_disabled' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:470:12: error: no previous prototype for 'pxa27x_clocks_init' [-Werror=missing-prototypes]
arch/arm/mach-pxa/pxa27x.c:44:6: error: no previous prototype for 'pxa27x_clear_otgph' [-Werror=missing-prototypes]
arch/arm/mach-pxa/pxa27x.c:58:6: error: no previous prototype for 'pxa27x_configure_ac97reset' [-Werror=missing-prototypes]
arch/arm/mach-pxa/spitz_pm.c:170:15: error: no previous prototype for 'spitzpm_read_devdata' [-Werror=missing-prototypes]
The problem is that there is a declaration for each of these, but
it's only seen by the caller and not the callee. Moving these
into appropriate header files ensures that both use the same
calling conventions and it avoids the warnings.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230516153109.514251-11-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In the unlikely event that something goes wrong with the device and
its registers, the fan_from_reg() function may return 0. This value
will cause a division-by-zero error in the show_pwm() function.
To prevent this, test the value of
fan_from_reg(data->fan_full_speed[nr]) against 0 before performing
the division. If the division-by-zero error is avoided, assign 0 to
the val variable.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: df9ec2dae0 ("hwmon: (f71882fg) Reorder symbols to get rid of a few forward declarations")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230510143537.145060-1-n.zhandarovich@fintech.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano).
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano).
- Clean up the hwmon thermal driver (Daniel Lezcano).
- Add thermal zone id accessor and thermal zone type accessor
and prevent drivers from using thermal zone fields directly (Daniel
Lezcano).
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano).
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui).
- Add more thermal zone device encapsulation: prevent setting structure
field directly, access the sensor device instead the thermal zone's
device for trace, relocate the traces in drivers/thermal (Daniel
Lezcano).
- Use the generic trip point for the i.MX and remove the get_trip_temp
ops (Daniel Lezcano).
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li).
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown (Wolfram
Sang).
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur).
- Add MT8365 support (Amjad Ouled-Ameur).
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel).
- Add driver support for RK3588 (Finley Xiao).
- Use devm_reset_control_array_get_exclusive() for the Rockchip driver
(Ye Xingchen).
- Detect power gated thermal zones and return -EAGAIN when reading the
temperature (Mikko Perttunen).
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring).
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn).
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai).
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen).
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI).
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano).
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano).
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano).
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui).
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki).
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring).
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki).
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada).
-----BEGIN PGP SIGNATURE-----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=XNJE
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These mostly continue to prepare the thermal control subsystem for
using unified representation of trip points, which includes cleanups,
code refactoring and similar and update several drivers (for other
reasons), which includes new hardware support.
Specifics:
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano)
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano)
- Clean up the hwmon thermal driver (Daniel Lezcano)
- Add thermal zone id accessor and thermal zone type accessor and
prevent drivers from using thermal zone fields directly (Daniel
Lezcano)
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano)
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui)
- Add more thermal zone device encapsulation: prevent setting
structure field directly, access the sensor device instead the
thermal zone's device for trace, relocate the traces in
drivers/thermal (Daniel Lezcano)
- Use the generic trip point for the i.MX and remove the
get_trip_temp ops (Daniel Lezcano)
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li)
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown
(Wolfram Sang)
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur)
- Add MT8365 support (Amjad Ouled-Ameur)
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel)
- Add driver support for RK3588 (Finley Xiao)
- Use devm_reset_control_array_get_exclusive() for the Rockchip
driver (Ye Xingchen)
- Detect power gated thermal zones and return -EAGAIN when reading
the temperature (Mikko Perttunen)
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring)
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn)
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai)
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen)
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI)
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano)
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano)
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano)
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui)
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki)
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring)
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki)
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada)"
* tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: intel: int340x: Add DLVR support for RFIM control
thermal/core: Alloc-copy-free the thermal zone parameters structure
thermal/of: Unexport unused OF functions
thermal/drivers/bcm2835: Remove buggy call to thermal_of_zone_unregister
thermal/drivers/mediatek/lvts_thermal: Add AP domain for mt8195
dt-bindings: thermal: mediatek: Add AP domain to LVTS thermal controllers for mt8195
thermal: amlogic: Use dev_err_probe()
thermal/drivers/mediatek/lvts_thermal: Fix sensor 1 interrupt status bitmask
MAINTAINERS: adjust entry in THERMAL/POWER_ALLOCATOR after header movement
dt-bindings: thermal: Drop unneeded quotes
thermal/core: Remove thermal_bind_params structure
thermal/drivers/tegra-bpmp: Handle offline zones
thermal/drivers/rockchip: use devm_reset_control_array_get_exclusive()
dt-bindings: rockchip-thermal: Support the RK3588 SoC compatible
thermal/drivers/rockchip: Support RK3588 SoC in the thermal driver
thermal/drivers/rockchip: Support dynamic sized sensor array
thermal/drivers/rockchip: Simplify channel id logic
thermal/drivers/rockchip: Use dev_err_probe
thermal/drivers/rockchip: Simplify clock logic
thermal/drivers/rockchip: Simplify getting match data
...
The bit flags in pmbus_driver_info functionality for YM-2151E chip were
joined with a comma operator instead of a bitwise OR. This means that
the last constant PMBUS_HAVE_IIN was not OR-ed with the other
PM_BUS_HAVE_* constants for this page but it initialized the next element
of the func array (which was not accessed from anywhere because of the
number of pages).
However, there is no need for setting PMBUS_HAVE_IIN in the 5Vsb page
because this command does not seem to be paged. Obviously, the device
only has one IIN sensor, so it doesn't make sense to query it again from
the second page.
Fixes: 1734b4135a ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Tomáš Pecka <tomas.pecka@cesnet.cz>
Link: https://lore.kernel.org/r/20230420171939.212040-1-tomas.pecka@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware sensors of the
Aquacomputer Aquastream XT watercooling pump, which communicates
through a proprietary USB HID protocol. Implemented by Leonard Anderweit
[1] [2].
Coolant temp, fan IC and external temp sensor readings are available, along
with speed and voltage of both the pump and optionally connected fan.
It also exposes pump current.
Additionally, serial number and firmware version are exposed through
debugfs.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/46
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/49
Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230416181702.9892-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configure the IT8622E chip to disable/re-enable access via an SMBus when
reading or writing the chip's registers.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Disable/re-enable access through SMBus for chip registers when they are
are being read or written.
For simple cases this is done at the same time as when a mutex is set,
however, within loops or during initialisation it is done separately.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
[groeck: Fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Handle errors from it87_update_device(), which currently only occurs if
SMBus access locking fails.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
[groeck: Fixed handling in show_temp_type()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add functions to disable and re-enable access by the SMBus for specific
chips.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the driver to use the default debugfs attributes instead of
ones that provide the same data under different names. Use the lock
functions for the debugfs and led attributes, and simplify the input
history operation by dropping the timer and lock.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230412161526.252294-3-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Debugfs operations may set the page number, which must be done
atomically with the subsequent i2c operation. Lock the update_lock
in the debugfs functions and provide a function for pmbus drivers
to lock and unlock the update_lock.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230412161526.252294-2-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
0-day rightfully complains:
drivers/hwmon/pmbus/pmbus_core.c:3164:7-32: WARNING:
Threaded IRQ with no primary handler requested without IRQF_ONESHOT
(unless it is nested IRQ)
Without IRQF_ONESHOT, the primary interrupt may end up in a loop,
and the threaded interrupt handler may never execute. Request interrupt
with IRQF_ONESHOT and assume that the interrupt will cleared and re-enabled
by clearing the fault condition in the threaded interrupt handler.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-hwmon/6436efbb.08+e+yEDqvRxvHDP%25lkp@intel.com/T/#u
Cc: Patrick Rudolph <patrick.rudolph@9elements.com>
Cc: Naresh Solanki <Naresh.Solanki@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TI ina2xx sensors according to datasheets have dedicated
vs supplies. Add it for proper work.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://lore.kernel.org/r/20230407160508.20479-3-clamor95@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add regulator events corresponding to regulator error in regulator flag
map.
Also capture the same in pmbus_regulator_get_flags.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230328150335.90238-2-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add driver for the StarFive JH71x0 temperature sensor. You
can enable/disable it and read temperature in milli Celcius
through sysfs.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Co-developed-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20230321022644.107027-3-hal.feng@starfivetech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The refinement of tjmax value retrieved from MSR_IA32_TEMPERATURE_TARGET
has been changed for several times.
Now, the raw value from MSR is used without refinement. Thus remove the
obsolete comment.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20230330103346.6044-2-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After commit c0c67f8761 ("hwmon: (coretemp) Add support for dynamic
tjmax"), tjmax value is retrieved from MSR every time the temperature is
read.
This means that, with debug message enabled, the tjmax debug message is
printed out for every single temperature read for any CPU. This spams
the syslog.
Ideally, as tjmax is package scope unique, the debug message should show
once when tjmax is changed for one package. But this requires inventing
some new per-package data in the coretemp driver, and this is overkill.
To keep the code simple, delete the tjmax debug message.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20230330103346.6044-1-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
clang with W=1 reports
drivers/hwmon/vt1211.c:198:20: error: unused function
'superio_outb' [-Werror,-Wunused-function]
static inline void superio_outb(int sio_cip, int reg, int val)
^
This function is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Juerg Haefliger <juergh@proton.me>
Link: https://lore.kernel.org/r/20230323211535.2637939-1-trix@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PWM fans are controlled solely by the duty cycle of the PWM signal, they
do not care about the exact timing. Thus set usage_power to true to
allow less flexible hardware to work as a PWM source for fan control.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://lore.kernel.org/r/20230309011009.2109696-1-lorenz@brun.one
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Boards such as
* EX-B660M-V5 D4,
* PRIME A520M-A,
* PRIME A520M-A II,
* PRIME A520M-E,
* PRIME A520M-K,
* PRIME B360M-A,
* PRIME B360M-C,
* PRIME B460M-A R2.0,
* PRIME B550M-A AC,
* PRIME B550M-A WIFI II,
* PRIME B550M-K,
* PRIME B650M-A AX II,
* PRIME Z590-P WIFI,
* PRIME Z590-V,
* Pro A520M-C,
* ProArt B650-CREATOR,
* ProArt Z790-CREATOR WIFI,
* Pro B660M-C,
* Pro WS W680-ACE,
* Pro WS W680-ACE IPMI,
* ROG MAXIMUS XIII APEX,
* ROG MAXIMUS XIII EXTREME,
* ROG MAXIMUS XIII HERO,
* ROG MAXIMUS Z690 APEX,
* ROG MAXIMUS Z790 EXTREME,
* ROG STRIX B660-A GAMING WIFI,
* ROG STRIX Z590-A GAMING WIFI,
* ROG STRIX Z590-E GAMING WIFI,
* ROG STRIX Z590-F GAMING WIFI,
* ROG STRIX Z590-I GAMING WIFI,
* TUF GAMING A520M-PLUS,
* TUF GAMING A520M-PLUS II,
* TUF GAMING A520M-PLUS WIFI,
* TUF GAMING B660M-E D4,
* TUF GAMING B660-PLUS WIFI D4,
* TUF GAMING X570-PLUS_BR,
* TUF GAMING Z590-PLUS,
* Z490-GUNDAM (WI-FI),
* Z590 WIFI GUNDAM EDITION
have got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
This commit adds such boards to the WMI monitoring list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Nick Owens <mischief@offblast.org>
Tested-by: A. M. <de99like@mennucci.debian.net>
Link: https://lore.kernel.org/r/20230315225128.1236-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add function pmbus get status that can be used to get both pmbus
specific status & regulator status
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
...
Change in V4
- None
Changes in V3:
- Add pmbus_is_enabled function
Changes in V2:
- Add __maybe attribute for pmbus_get_status function
- Remove unrelated changes
Link: https://lore.kernel.org/r/20230301164434.1928237-2-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PMBus status flag map(pmbus_regulator_status_flag_map) is moved
outside of the regulator #if block and the associated variable/struct
name updated to reflect as generic PMBus status.
This will make the PMBus status flag map more versatile and easier to
incorporate into different contexts and functions.
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230301164434.1928237-1-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the option to control fan PWM on Aquacomputer Aquaero. The Aquaero is
the most complex Aquacomputer device, control is therefore more complicated
then on already supported devices.
Setting PWM requires multiple steps. First, an internal static PWM
controller is set to the desired PWM value. Second, the fan is set to use
that PWM controller. Last, the minimum and maximum accepted PWM values
of the fan are set to allow all possible PWM values.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-7-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add information on the Aquacomputer Aquaero control report and disable the
control report checksum for Aquaero. The Aquaero does not use the checksum
so it must be disabled to avoid overwriting the last two bytes of the
control report.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-5-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device dependent control report id, secondary control report id,
secondary control report size and secondary control report for devices
which need different control report settings. All currently supported
devices use the same values.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-4-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add new function aqc_set_ctrl_vals() to support changing multiple control
values at once while sending only one control report.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-3-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for one byte control values. This extends aqc_set_ctrl_val()
and aqc_get_ctrl_val() with a type. Currently supported types are AQC_8
(one byte) and AQC_BE16 (two bytes big endian). More types will be added
in the future.
Signed-off-by: Leonard Anderweit <leonard.anderweit@gmail.com>
Link: https://lore.kernel.org/r/20230214220221.15003-2-leonard.anderweit@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144706.1542434-1-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144707.1542525-1-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 64-bit result will be cut to 32-bit automatically (by compiler)
due to the type of the destination value. No need to have an explicit
casting and especially additional conjunction which does the same.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230217191600.24837-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This seems to be a new revision of the device. RGB controls have changed,
but this driver doesn't touch them anyway.
Fan speed control reported to be working with existing userspace (hidraw)
software, so I assume it's compatible. Fan channel count is the same.
Recently added (0x1e71, 0x2019) seems to be the same device.
Discovered in liquidctl project:
https://github.com/liquidctl/liquidctl/issues/541
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20230219105924.333007-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Osama Muhammad