wireless-testing
commit 37e5bf6535
Author: Luis R. Rodriguez <lrodriguez@atheros.com>
Date: Sat Jun 12 00:33:40 2010 -0400
ath9k_hw: fix clock rate calculations for ANI
This commit accidentally broke clock rate calculation by doubling the
calculated clock rate
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a WARN_ON failure in bond_masters sysfs file
Got a report of this warning recently
bonding: bond0 is being created...
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:590 proc_register+0x14d/0x185()
Hardware name: ProLiant BL465c G1
proc_dir_entry 'bonding/bond0' already registered
Modules linked in: bonding ipv6 tg3 bnx2 shpchp amd64_edac_mod edac_core
ipmi_si
ipmi_msghandler serio_raw i2c_piix4 k8temp edac_mce_amd hpwdt microcode hpsa
cc
iss radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core [last unloaded:
scsi_wai
t_scan]
Pid: 935, comm: ifup-eth Not tainted 2.6.33.5-124.fc13.x86_64 #1
Call Trace:
[<ffffffff8104b54c>] warn_slowpath_common+0x77/0x8f
[<ffffffff8104b5b1>] warn_slowpath_fmt+0x3c/0x3e
[<ffffffff8114bf0b>] proc_register+0x14d/0x185
[<ffffffff8114c20c>] proc_create_data+0x87/0xa1
[<ffffffffa0211e9b>] bond_create_proc_entry+0x55/0x95 [bonding]
[<ffffffffa0215e5d>] bond_init+0x95/0xd0 [bonding]
[<ffffffff8138cd97>] register_netdevice+0xdd/0x29e
[<ffffffffa021240b>] bond_create+0x8e/0xb8 [bonding]
[<ffffffffa021c4be>] bonding_store_bonds+0xb3/0x1c1 [bonding]
[<ffffffff812aec85>] class_attr_store+0x27/0x29
[<ffffffff8115423d>] sysfs_write_file+0x10f/0x14b
[<ffffffff81101acf>] vfs_write+0xa9/0x106
[<ffffffff81101be2>] sys_write+0x45/0x69
[<ffffffff81009b02>] system_call_fastpath+0x16/0x1b
---[ end trace a677c3f7f8b16b1e ]---
bonding: Bond creation failed.
It happens because a user space writer to bond_master can try to
register an already existing bond interface name. Fix it by teaching
bond_create to check for the existance of devices with that name first
in cases where a non-NULL name parameter has been passed in
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skge devices installed on some Gigabyte motherboards are not able to
perform 64 dma correctly due to board PCI implementation, so limit
DMA to 32bit if such boards are detected.
Bug was reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=447489
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
vlan: dont drop packets from unknown vlans in promiscuous mode
Phonet: Correct header retrieval after pskb_may_pull
um: Proper Fix for f25c80a4: remove duplicate structure field initialization
ip_gre: Fix dependencies wrt. ipv6.
net-2.6: SYN retransmits: Add new parameter to retransmits_timed_out()
iwl3945: queue the right work if the scan needs to be aborted
mac80211: fix use-after-free
Since 'select' ignores dependencies, drivers that select INET_LRO must
depend on INET. This fixes the broken configuration reported in
<http://article.gmane.org/gmane.linux.kernel/825646>.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwl3945's scan_completed calls into the mac80211 stack which triggers a
warn on if there is no scan outstanding.
This can be avoided by not calling scan_completed but abort_scan in
iwl3945_request_scan in the done: branch of the function which is used
as an error out.
The done: branch seems to be an error-out branch, as, for example, if
iwl_is_ready(priv) returns false the done: branch is executed.
NOTE:
I'm not familiar with the driver at all.
I just quickly scanned as a reaction to
https://bugzilla.kernel.org/show_bug.cgi?id=17722
the users of scan_completed in the iwl3945 driver and noted the odd
discrepancy between the comment above this instance and the comment in
mac80211 scan_completed function.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
tcp: Fix >4GB writes on 64-bit.
net/9p: Mount only matching virtio channels
de2104x: fix ethtool
tproxy: check for transparent flag in ip_route_newports
ipv6: add IPv6 to neighbour table overflow warning
tcp: fix TSO FACK loss marking in tcp_mark_head_lost
3c59x: fix regression from patch "Add ethtool WOL support"
ipv6: add a missing unregister_pernet_subsys call
s390: use free_netdev(netdev) instead of kfree()
sgiseeq: use free_netdev(netdev) instead of kfree()
rionet: use free_netdev(netdev) instead of kfree()
ibm_newemac: use free_netdev(netdev) instead of kfree()
smsc911x: Add MODULE_ALIAS()
net: reset skb queue mapping when rx'ing over tunnel
br2684: fix scheduling while atomic
de2104x: fix TP link detection
de2104x: fix power management
de2104x: disable autonegotiation on broken hardware
net: fix a lockdep splat
e1000e: 82579 do not gate auto config of PHY by hardware during nominal use
...
When the interface is up, using ethtool breaks it because:
a) link is put down but media_timer interval is not shortened to NO_LINK
b) rxtx is stopped but not restarted
Also manual 10baseT-HD (and probably FD too - untested) mode does not work -
the link is forced up, packets are transmitted but nothing is received.
Changing CSR14 value to match documentation (not disabling link check) fixes this.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (commit 690a1f2002) added a
new call site for acpi_set_WOL() without checking that the function is
actually suitable to be called via
vortex_set_wol+0xcd/0xe0 [3c59x]
dev_ethtool+0xa5a/0xb70
dev_ioctl+0x2e0/0x4b0
T.961+0x49/0x50
sock_ioctl+0x47/0x290
do_vfs_ioctl+0x7f/0x340
sys_ioctl+0x80/0xa0
system_call_fastpath+0x16/0x1b
i.e. outside of code paths run when the device is not yet enabled or
already disabled. In particular, putting the device into D3hot is a
pretty bad idea when it was already brought up.
Furthermore, all prior callers of the function made sure they're
actually dealing with a PCI device, while the newly added one didn't.
In the same spirit, the .get_wol handler shouldn't indicate support
for WOL for non-PCI devices.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables auto loading for the smsc911x ethernet driver.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).
Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).
This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.
Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.
Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).
de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets. This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register. It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately. Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls
the accounting of missed packets, these will go unnoticed. Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.
[1] commit e98cac447c
[2] commit 3f0c16e844
CC: stable@kernel.org
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers. On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed. Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively). The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are allocated in atl1_setup_ring_resources, zero out the pointers
in atl1_free_ring_resources (like the other resources).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).
Cc: stable@kernel.org
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is set in core network.
Dont change it unless dealing with fragments.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
dca: disable dca on IOAT ver.3.0 multiple-IOH platforms
netpoll: Disable IRQ around RCU dereference in netpoll_rx
sctp: Do not reset the packet during sctp_packet_config().
net/llc: storing negative error codes in unsigned short
MAINTAINERS: move atlx discussions to netdev
drivers/net/cxgb3/cxgb3_main.c: prevent reading uninitialized stack memory
drivers/net/eql.c: prevent reading uninitialized stack memory
drivers/net/usb/hso.c: prevent reading uninitialized memory
xfrm: dont assume rcu_read_lock in xfrm_output_one()
r8169: Handle rxfifo errors on 8168 chips
3c59x: Remove atomic context inside vortex_{set|get}_wol
tcp: Prevent overzealous packetization by SWS logic.
net: RPS needs to depend upon USE_GENERIC_SMP_HELPERS
phylib: fix PAL state machine restart on resume
net: use rcu_barrier() in rollback_registered_many
bonding: correctly process non-linear skbs
ipv4: enable getsockopt() for IP_NODEFRAG
ipv4: force_igmp_version ignored when a IGMPv3 query received
ppp: potential NULL dereference in ppp_mp_explode()
net/llc: make opt unsigned in llc_ui_setsockopt()
...
qlcnic driver allocates rx skbs and gives to hardware too bytes of extra
storage, allowing for corruption of kernel data.
NET_IP_ALIGN being 0 on some platforms (including x86), drivers should
not assume it's 2.
rds_ring->skb_size = rds_ring->dma_size + NET_IP_ALIGN;
...
skb = dev_alloc_skb(rds_ring->skb_size);
skb_reserve(skb, 2);
pci_map_single(pdev, skb->data, rds_ring->dma_size, PCI_DMA_FROMDEVICE);
(and rds_ring->skb_size == rds_ring->dma_size) -> bug
Because of extra alignment (1500 + 32) -> four extra bytes are available
before the struct skb_shared_info, so corruption is not noticed.
Note: this driver could use netdev_alloc_skb_ip_align()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed formatting (tabs and line breaks).
The CHELSIO_GET_QSET_NUM device ioctl allows unprivileged users to read
4 bytes of uninitialized stack memory, because the "addr" member of the
ch_reg struct declared on the stack in cxgb_extension_ioctl() is not
altered or zeroed before being copied back to the user. This patch
takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed formatting (tabs and line breaks).
The EQL_GETMASTRCFG device ioctl allows unprivileged users to read 16
bytes of uninitialized stack memory, because the "master_name" member of
the master_config_t struct declared on the stack in eql_g_master_cfg()
is not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed formatting (tabs and line breaks).
The TIOCGICOUNT device ioctl allows unprivileged users to read
uninitialized stack memory, because the "reserved" member of the
serial_icounter_struct struct declared on the stack in hso_get_count()
is not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Thinkpad X100e seems to have some odd behaviour when the display is
powered off - the onboard r8169 starts generating rxfifo overflow errors.
The root cause of this has not yet been identified and may well be a
hardware design bug on the platform, but r8169 should be more resiliant to
this. This patch enables the rxfifo interrupt on 8168 devices and removes
the MAC version check in the interrupt handler, and the machine no longer
crashes when under network load while the screen turns off.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some pcnet_cs compatible cards require an exact 16-lines match
of the ioport areas specified in CIS, but set the "iolines"
value in the CIS incorrectly. We can easily work around this
issue -- same as we do in serial_cs -- by first trying setting
iolines to the CIS-specified value, and then trying a 16-line
match.
Reported-and-tested-by: Wolfram Sang <w.sang@pengutronix.de>
Hardware-supplied-by: Jochen Frieling <j.frieling@pengutronix.de>
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
On resume, before starting the PAL state machine, check if the
adjust_link() method is well supplied. If not, this would lead to a
NULL pointer dereference in the phy_state_machine() function.
This scenario can happen if the Ethernet driver call manually the PHY
functions instead of using the PAL state machine. The mv643xx_eth driver
is a such example.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently brought to my attention that 802.3ad mode bonds would no
longer form when using some network hardware after a driver update.
After snooping around I realized that the particular hardware was using
page-based skbs and found that skb->data did not contain a valid LACPDU
as it was not stored there. That explained the inability to form an
802.3ad-based bond. For balance-alb mode bonds this was also an issue
as ARPs would not be properly processed.
This patch fixes the issue in my tests and should be applied to 2.6.36
and as far back as anyone cares to add it to stable.
Thanks to Alexander Duyck <alexander.h.duyck@intel.com> and Jesse
Brandeburg <jesse.brandeburg@intel.com> for the suggestions on this one.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: stable@kerne.org
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: move probe call to subsys_initcall()
powerpc/5200: mpc52xx_uart.c: Add of_node_put to avoid memory leak
spi/pl022: fix APB pclk power regression on U300
spi/spi_s3c64xx: Warn if PIO transfers time out
spi/s3c64xx: Fix incorrect reuse of 'val' local variable.
spi/s3c64xx: Fix compilation warning
spi/dw_spi: clean the cs_control code
spi/dw_spi: Allow interrupt sharing
spi/spi_s3c64xx: Increase dead reckoning time in wait_for_xfer()
spi/spi_s3c64xx: Move to subsys_initcall()
spi: free children in spi_unregister_master, not siblings
gpiolib: Add 'struct gpio_chip' forward declaration for !GPIOLIB case
of: Fix missing includes - ll_temac
spi/spi_s3c64xx: Staticise non-exported functions
spi/spi_s3c64xx: Make probe more robust against missing board config
Smatch complains because we check whether "pch->chan" is NULL and then
dereference it unconditionally on the next line. Partly the reason this
bug was introduced is because code was too complicated. I've simplified
it a little.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'wwan' devtype is meant for devices that require preconfiguration
and *every* time setup before the ethernet interface can be used, like
cellular modems which require a series of setup commands on serial ports
or other mechanisms before the ethernet interface will handle packets.
As ipheth only requires one-per-hotplug pairing setup with no
preconfiguration (like APN, phone #, etc) and the network interface is
usable at any time after that initial setup, remove the incorrect
devtype wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_alloc_skb_ip_align() helper and do correct allocation
Tested-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not. However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command. Therefore this is at least a local
denial-of-service vulnerability.
Change it to check before writing each entry and to return an error if
the buffer is already full.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
pkt_sched: Fix lockdep warning on est_tree_lock in gen_estimator
ipvs: avoid oops for passive FTP
Revert "sky2: don't do GRO on second port"
gro: fix different skb headrooms
bridge: Clear INET control block of SKBs passed into ip_fragment().
3c59x: Remove incorrect locking; correct documented lock hierarchy
sky2: don't do GRO on second port
ipv4: minor fix about RPF in help of Kconfig
xfrm_user: avoid a warning with some compiler
net/sched/sch_hfsc.c: initialize parent's cl_cfmin properly in init_vf()
pxa168_eth: fix a mdiobus leak
net sched: fix kernel leak in act_police
vhost: stop worker only if created
MAINTAINERS: Add ehea driver as Supported
ath9k_hw: fix parsing of HT40 5 GHz CTLs
ath9k_hw: Fix EEPROM uncompress block reading on AR9003
wireless: register wiphy rfkill w/o holding cfg80211_mutex
netlink: Make NETLINK_USERSOCK work again.
irda: Correctly clean up self->ias_obj on irda_bind() failure.
wireless extensions: fix kernel heap content leak
...
It causes all kinds of DMA API debugging assertions and
all straight-forward attempts to fix it have failed.
So turn off SG, and we'll tackle making this work
properly in net-next-2.6
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller