Driver currently uses advertised-autoneg value to populate the
supported-autoneg field. When advertised field is updated, user gets
the same value for supported field. Supported-autoneg value need to be
populated from the link capabilities value returned by the MFW.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value for status block id could be more than 256 in 100G mode, need to
update its data type from u8 to u16.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V2: using "aquantia" subsystem tag.
The command "ethtool -i ethX" should display driver name (driver: atlantic)
instead vendor name (driver: aquantia).
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since netif_carrier_on() will do nothing if device's
carrier is already on, so it's unnecessary to do
carrier status check.
It's the same for netif_carrier_off().
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restart of the subqueue should occur outside of the loop processing
any tx buffers instead of doing this in the middle of the loop.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Map each RX SKB to the RX queue associated with the driver's RX SCRQ.
This should improve the RX CPU load balancing issues seen by the
performance team.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not a need to stop processing skbs if we encounter a
skb that has a receive completion error.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the check for the driver resetting to the first thing
in ibmvnic_xmit().
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When closing the ibmvnic driver we need to wait for any pending
sub crq entries to ensure they are handled.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When closing the ibmvnic driver, most notably during the reset
path, the tx pools need to be cleaned to ensure there are no
hanging skbs that need to be free'ed.
The need for this was found during debugging a loss of network
traffic after handling a driver reset. The underlying cause was
some skbs in the tx pool that were never free'ed. As a
result the upper network layers never tried a re-send since it
believed the driver still had the skb.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi structs allocated at drivier initializatio need to be
free'ed when releasing the drivers resources.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver has multiple handlers for resetting the driver
depending on the reason the reset is needed (failover, lpm,
fatal erors,...). All of the reset handlers do essentially the same
thing, this patch moves this work to a common reset handler.
By doing this we also allow the driver to better handle situations
where we can get a reset while handling a reset.
The updated reset handling works by adding a reset work item to the
list of resets and then scheduling work to perform the reset. This
step is necessary because we can receive a reset in interrupt context
and we want to handle the reset out of interrupt context.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the is_closed flag in the ibmvnic adapter strcut with a
more comprehensive state field that tracks the current state of
the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all of the calls to initialize resources for the driver to
a separate routine.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now tg3 NIC's stats will be cleared after ifdown/ifup. bond_get_stats traverse
its salves to get statistics,cumulative the increment.If a tg3 NIC is added to
bonding as a slave,ifdown/ifup will cause bonding's stats become tremendous value
(ex.1638.3 PiB) because of negative increment.
Fixes: 92feeabf3f ("tg3: Save stats across chip resets")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small follow-up to d74a32acd5 ("xdp: use netlink extended ACK reporting")
in order to let drivers all use the same NL_SET_ERR_MSG_MOD() helper macro
for reporting. This also ensures that we consistently add the driver's
prefix for dumping the report in user space to indicate that the error
message is driver specific and not coming from core code. Furthermore,
NL_SET_ERR_MSG_MOD() now reuses NL_SET_ERR_MSG() and thus makes all macros
check the pointer as suggested.
References: https://www.spinics.net/lists/netdev/msg433267.html
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for Microchip LAN9250 Ethernet controller.
Signed-off-by: David Cai <david.cai@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.12:
API:
- Add batch registration for acomp/scomp
- Change acomp testing to non-unique compressed result
- Extend algorithm name limit to 128 bytes
- Require setkey before accept(2) in algif_aead
Algorithms:
- Add support for deflate rfc1950 (zlib)
Drivers:
- Add accelerated crct10dif for powerpc
- Add crc32 in stm32
- Add sha384/sha512 in ccp
- Add 3des/gcm(aes) for v5 devices in ccp
- Add Queue Interface (QI) backend support in caam
- Add new Exynos RNG driver
- Add ThunderX ZIP driver
- Add driver for hardware random generator on MT7623 SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (101 commits)
crypto: stm32 - Fix OF module alias information
crypto: algif_aead - Require setkey before accept(2)
crypto: scomp - add support for deflate rfc1950 (zlib)
crypto: scomp - allow registration of multiple scomps
crypto: ccp - Change ISR handler method for a v5 CCP
crypto: ccp - Change ISR handler method for a v3 CCP
crypto: crypto4xx - rename ce_ring_contol to ce_ring_control
crypto: testmgr - Allow ecb(cipher_null) in FIPS mode
Revert "crypto: arm64/sha - Add constant operand modifier to ASM_EXPORT"
crypto: ccp - Disable interrupts early on unload
crypto: ccp - Use only the relevant interrupt bits
hwrng: mtk - Add driver for hardware random generator on MT7623 SoC
dt-bindings: hwrng: Add Mediatek hardware random generator bindings
crypto: crct10dif-vpmsum - Fix missing preempt_disable()
crypto: testmgr - replace compression known answer test
crypto: acomp - allow registration of multiple acomps
hwrng: n2 - Use devm_kcalloc() in n2rng_probe()
crypto: chcr - Fix error handling related to 'chcr_alloc_shash'
padata: get_next is never NULL
crypto: exynos - Add new Exynos RNG driver
...
Driver follows a method of taking one extra reference on the
page for recycling which is fine in usual packet path where
each 64KB page is segmented into multiple receive buffers.
But in XDP mode since there is just one receive buffer per
page taking extra page reference itself becomes big bottleneck
consuming ~50% of CPU cycles due to atomic operations.
This patch adds a internal ref count in pgcache for each
page and additional page references are taken in a batch
instead of just one at a time. Internal i.e 'pgcache->ref_count'
and page's i.e 'page->_refcount' counters are compared to check
page's recyclability.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in XDP mode reserve XDP_PACKET_HEADROOM bytes at the start
of receive buffer for XDP program to modify headers and adjust
packet start. Additional code changes done to handle such packets.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for XDP_TX i.e transmits packet out of
the XDP TX queue mapped to the corresponding Rx queue
on which packet is received.
Since SQ for XDP TX will be used only on a single cpu i.e
SQ description creation and freeing, using atomic free count
is not necessary and will become a bottleneck. Hence added
a separate 'xdp_free_cnt' used for SQs designated for XDP
to track descriptor free count.
Changes also include
- A new entry 'xdp_page' is added to save transmitted packet's
page pointer for later cleanup.
- XDP Tx SQ's doorbell is ringed once per NAPI instance.
- Retrieving designated SQ for packets being sent out by stack
via 'nicvf_xmit'.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for XDP_DROP.
Also since in XDP mode there is just a single buffer per page,
made changes to recycle DMA mapping info as well along with pages.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds basic XDP support i.e attaching a BPF program to an
interface. Also takes care of allocating separate Tx queues
for XDP path and for network stack packet transmission.
This patch doesn't support handling of any of the XDP actions,
all are treated as XDP_PASS i.e packets will be handed over to
the network stack.
Changes also involve allocating one receive buffer per page in XDP
mode and multiple in normal mode i.e when no BPF program is attached.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of unnecessary double pointer references and type casting
in receive buffer allocation code.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimized CQE handling with below changes
- Feeing descriptors back to SQ in bulk i.e once per NAPI
instance instead for every CQE_TX, this will reduce number
of atomic updates to 'sq->free_cnt'.
- Checking errors in CQE_TX and CQE_RX before calling appropriate
fn()s to update error stats i.e reduce branching.
Also removed debug messages in packet handling path which otherwise
causes issues if DEBUG is enabled.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive buffer's physical address or iova will anyway not
go beyond 49bits, since it is the max supported HW address.
As per perf, updating bitfields i.e buf_addr:42 in RBDR
descriptor entry consumes lots of cpu cycles, hence changed
it to a 64bit field with alignment requirements taken care of.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for page recycling for allocating receive buffers
to reduce cost of refilling RBDR ring. Also got rid of using
compound pages when pagesize is 4K, only order-0 pages now.
Only page is recycled, DMA mappings still needs to be done for
every receive buffer allocated due to following constraints
- Cannot have just one receive buffer per 64KB page.
- There is just one buffer ring shared across 8 Rx queues, so
buffers of same page can go to any Rx queue.
- HW gives buffer address where packet has been DMA'ed and not
the index into buffer ring.
This makes it not possible to resue DMA mapping info. So unfortunately
have to go through costly mapping route for every buffer.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
TimeSync/"V1 frame format support"/"V2 frame format support" on
the TX side. Set the associated bits based on the user request.
2. ptp4l application fails to operate in Peer Delay mode. Following
changes are needed to fix this,
a. Driver should enable (set to 0) DA #1-related bits for IPv4,
IPv6 and MAC destination addresses in these registers:
NIG_REG_TX_LLH_PTP_RULE_MASK
NIG_REG_LLH_PTP_RULE_MASK
b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
be set to 0x0 in all modes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Tx timestamping data structures are not protected against the
concurrent access in the Tx paths. Protecting the same using atomic
bit locks.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IOT2000 is industrial controller platform, derived from the Intel
Galileo Gen2 board. The variant IOT2020 comes with one LAN port, the
IOT2040 has two of them. They can be told apart based on the board asset
tag in the DMI table.
Based on patch by Sascha Weisenberger.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is enslaved to a VRF master, its router interface (RIF)
needs to be destroyed (if exists) and a new one created using the
corresponding virtual router (VR).
>From the driver's perspective, the above is equivalent to an inetaddr
event sent for this netdev. Therefore, when a port netdev (or its
uppers) are enslaved to a VRF master, call the same function that
would've been called had a NETDEV_UP was sent for this netdev in the
inetaddr notification chain.
This patch also fixes a bug when a LAG netdev with an existing RIF is
enslaved to a VRF. Before this patch, each LAG port would drop the
reference on the RIF, but would re-join the same one (in the wrong VR)
soon after. With this patch, the corresponding RIF is first destroyed
and a new one is created using the correct VR.
Fixes: 7179eb5acd ("mlxsw: spectrum_router: Add support for VRFs")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or says:
================
mlx5 neigh update
This series (whose code name is 'neigh update') from Hadar, enhances the
mlx5 TC IP tunnel offloads to deal with changes to tunnel destination
neighbours used in offloaded flows which involved encapsulation.
In order to keep track on the validity state of such neighbours, we register
a netevent notifier callback and act on NEIGH_UPDATE events: if a neighbour
becomes valid, offload the related flows to HW (the other way around when
neigh becomes invalid) and similarly when a neigh mac addresses changes.
Since this traffic is offloaded from the host OS, the neighbour for the IP
tunnel destination can mistakenly become STALE and deleted by the kernel
since its 'used' value wasn't changed. To address that, we proactively
update the neighbour 'used' value every DELAY_PROBE_TIME seconds, using
time stamps generated by the existing driver code for HW flow counters.
We use the DELAY_PROBE_TIME_UPDATE event to adjust the frequency of the updates.
Prior to the core of the series, there's a patch from Saeed that introduces an
extendable vport representor implementation scheme. It provides a separation
between the eswitch to the netdev related aspects of the representors.
We would like to thank Ido Schimmel and Ilya Lesokhin for their coaching && advice
through the long design and review cycles while we struggled to understand and
(hopefully correctly) implement the locking around the different driver flows(..) .
- Or.
=================
Misc Updates:
From Tariq:
Some small performance and trivial code optimization for mlx5 netdev driver
- Optimize poll ICOSQ completion queue
- Use prefetchw when a write is to follow
- Use u8 as ownership type in mlx5e_get_cqe()
From Eran:
- Disable LRO by default on specific setups
From Eli:
- Small cleanup for E-Switch to avoid redundant allocation
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZBeGlAAoJEEg/ir3gV/o+AuMH/2OfS+diXrTMU90tQGfucurg
cPuv2qSGzSzcyFOjMUKL/hgj+y8HcUNZVSqts/LPhUj5CbR8On2jo/3XZb405SMX
1eAffpD5JxDGm4xQCADwkDMRVOuWNbXlTceRMbD+8vDtboTDEZwbaXX20En6MIEW
qcQPX0wv7/u8VpxGlhch2RRvl7+zBhhGCLNpwzkE5K+RggIPguE+F2hLpm+SH9PD
AOHSuwGWnE40In8dZIPqsEnUsmsC9LmUQ17ip8S8dEtGDHMvwDelsKGZcRGMuwoz
wSxpVTWn5JaU0EwN0t+rYtERFH18SqboG3OFwqb27qtRns6ALXIx3Dj1bb9sVBo=
=3qOg
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-04-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2017-04-30
Or says:
================
mlx5 neigh update
This series (whose code name is 'neigh update') from Hadar, enhances the
mlx5 TC IP tunnel offloads to deal with changes to tunnel destination
neighbours used in offloaded flows which involved encapsulation.
In order to keep track on the validity state of such neighbours, we register
a netevent notifier callback and act on NEIGH_UPDATE events: if a neighbour
becomes valid, offload the related flows to HW (the other way around when
neigh becomes invalid) and similarly when a neigh mac addresses changes.
Since this traffic is offloaded from the host OS, the neighbour for the IP
tunnel destination can mistakenly become STALE and deleted by the kernel
since its 'used' value wasn't changed. To address that, we proactively
update the neighbour 'used' value every DELAY_PROBE_TIME seconds, using
time stamps generated by the existing driver code for HW flow counters.
We use the DELAY_PROBE_TIME_UPDATE event to adjust the frequency of the updates.
Prior to the core of the series, there's a patch from Saeed that introduces an
extendable vport representor implementation scheme. It provides a separation
between the eswitch to the netdev related aspects of the representors.
We would like to thank Ido Schimmel and Ilya Lesokhin for their coaching && advice
through the long design and review cycles while we struggled to understand and
(hopefully correctly) implement the locking around the different driver flows(..) .
- Or.
=================
Misc Updates:
From Tariq:
Some small performance and trivial code optimization for mlx5 netdev driver
- Optimize poll ICOSQ completion queue
- Use prefetchw when a write is to follow
- Use u8 as ownership type in mlx5e_get_cqe()
From Eran:
- Disable LRO by default on specific setups
From Eli:
- Small cleanup for E-Switch to avoid redundant allocation
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing the PTP related initialization from slowpath start,
the remaining PTT entry is required only in case CONFIG_RFS_ACCEL is set.
Otherwise, it leads to a warning due to it being unused.
Fixes: d179bd1699 ("qed: Acquire/release ptt_ptp lock when enabling/disabling PTP")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output to the RDMA driver whether DPM mode is enabled or disabled in
the HW and if so what is the number of WIDs it supports
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating doorbell BAR partitioning round up the number of
CPUs to the nearest power of 2 so the size of the DPI (per user
section) configured in the hardware will be stored properly and
not truncated.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mechanism to verify RoCE resources are released prior to freeing the
bitmaps. If this is not the case, print what resources were not released.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the posting of the ramrod for the purpose of TID deregistration
fails, abort the deregistration operation without using the FW's
return code.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal RoCE SQE QP state isn't being used. Instead we mark the
QP as in regular error state.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use time_before_eq for time comparison more safe and dealing
with timer wrapping to be future-proof.
Signed-off-by: Karim Eshapa <karim.eshapa@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to carry error messages to the user via the netlink extended
ack message attribute.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistakes in printk message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presumably we never hit this return, but static checkers complain that
we need to unlock so we may as well fix that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that we're holding a mutex on this error
path. Let's goto exit instead of returning directly.
Fixes: b0bccb69eb ("qed: Change locking scheme for VF channel")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hip06 and hip07 SoCs, phy connect to mdio bus.The mdio
module is probed with module_init, and, as such,
is not guaranteed to probe before the HNS driver. So we need
to support deferred probe.
We check for probe deferral in the mac init, so we not init DSAF
when there is no mdio, and free all resource, to later learn that
we need to defer the probe.
Signed-off-by: lipeng <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sudarsana.kalluru@cavium.com